mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-23 23:42:43 +00:00
b2681e584c
We are close to provide enduser friendly OpenWrt images for DGS-1210 switches that do not need serial console. Nevertheless a small bit is missing. We cannot switch back to the vendor partition or initiate a download of a vendor firmware image. To issue this from inside OpenWrt we need write access to U-Boot environment. Case 1: Switch back to secondary (vendor) image > fw_setenv bootcmd run addargs\; bootm 0xb4e80000 > fw_setenv image /dev/mtdblock7 > reboot Case 2: Issue D-Link Network Assistant based download on next reboot. This is a combination of some vendor specific protocol (DDP) and a TFTP download afterwards. > fw_setenv bootstop on > reboot Allow these commands by opening up u-boot-env for write access. Tested on DGS-1210-20. Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
87 lines
1.5 KiB
Plaintext
87 lines
1.5 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "rtl838x.dtsi"
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
/ {
|
|
aliases {
|
|
led-boot = &led_power;
|
|
led-failsafe = &led_power;
|
|
led-running = &led_power;
|
|
led-upgrade = &led_power;
|
|
};
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x8000000>;
|
|
};
|
|
|
|
leds {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinmux_disable_sys_led>;
|
|
|
|
compatible = "gpio-leds";
|
|
|
|
led_power: power {
|
|
label = "green:power";
|
|
gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&gpio0 {
|
|
indirect-access-bus-id = <0>;
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <10000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x00000000 0x80000>;
|
|
read-only;
|
|
};
|
|
partition@80000 {
|
|
label = "u-boot-env";
|
|
reg = <0x00080000 0x40000>;
|
|
};
|
|
partition@c0000 {
|
|
label = "board-name";
|
|
reg = <0x000c0000 0x40000>;
|
|
};
|
|
partition@280000 {
|
|
label = "firmware";
|
|
compatible = "denx,uimage";
|
|
reg = <0x00100000 0xd80000>;
|
|
};
|
|
partition@be80000 {
|
|
label = "kernel2";
|
|
reg = <0x00e80000 0x180000>;
|
|
};
|
|
partition@1000000 {
|
|
label = "sysinfo";
|
|
reg = <0x01000000 0x40000>;
|
|
};
|
|
partition@1040000 {
|
|
label = "rootfs2";
|
|
reg = <0x01040000 0xc00000>;
|
|
};
|
|
partition@1c40000 {
|
|
label = "jffs2";
|
|
reg = <0x01c40000 0x3c0000>;
|
|
};
|
|
};
|
|
};
|
|
};
|