openwrt/package/firmware/ipq-wifi/Makefile
Felix Matouschek 1cc3b95efc ipq40xx: Add support for Teltonika RUTX10
This patch adds support for the Teltonika RUTX10.
This device is an industrial DIN-rail router with 4 ethernet ports,
2.4G/5G dualband WiFi, Bluetooth, a USB 2.0 port and two GPIOs.

The RUTX series devices are very similiar so common parts of the DTS
are kept in a DTSI file. They are based on the QCA AP-DK01.1-C1 dev
board.

See https://teltonika-networks.com/product/rutx10 for more info.

Hardware:
  SoC:                 Qualcomm IPQ4018
  RAM:                 256MB DDR3
  SPI Flash 1:         XTX XT25F128B (16MB, NOR)
  SPI Flash 2:         XTX XT26G02AWS (256MB, NAND)
  Ethernet:            Built-in IPQ4018 (SoC, QCA8075), 4x 10/100/1000 ports
  WiFi 1:              Qualcomm QCA4019 IEEE 802.11b/g/n
  Wifi 2:              Qualcomm QCA4019 IEEE 802.11a/n/ac
  USB Hub:             Genesys Logic GL852GT
  Bluetooth:           Qualcomm CSR8510 (A10U)
  LED/GPIO controller: STM32F030 with custom firmware
  Buttons:             Reset button
  Leds:                Power (green, cannot be controlled)
                       WiFi 2.4G activity (green)
                       WiFi 5G activity (green)

MACs Details verified with the stock firmware:
   eth0:             Partition 0:CONFIG Offset: 0x0
   eth1:             = eth0 + 1
   radio0 (2.4 GHz): = eth0 + 2
   radio1 (5.0 GHz): = eth0 + 3
Label MAC address is from eth0.

The LED/GPIO controller needs a separate kernel driver to function.
The driver was extracted from the Teltonika GPL sources and can be
found at following feed: https://github.com/0xFelix/teltonika-rutx-openwrt

USB detection of the bluetooth interface is sometimes a bit flaky. When
not detected power cycle the device. When the bluetooth interface was
detected properly it can be used with bluez / bluetoothctl.

Flash instructions via stock web interface (sysupgrade based):
  1. Set PC to fixed ip address 192.168.1.100
  2. Push reset button and power on the device
  3. Open u-boot HTTP recovery at http://192.168.1.1
  4. Upload latest stock firmware and wait until the device is rebooted
  5. Open stock web interface at http://192.168.1.1
  6. Set some password so the web interface is happy
  7. Go to firmware upgrade settings
  8. Choose
     openwrt-ipq40xx-generic-teltonika_rutx10-squashfs-nand-factory.ubi
  9. Set 'Keep settings' to off
  10. Click update, when warned that it is not a signed image proceed

Return to stock firmware:
  1. Set PC to fixed ip address 192.168.1.100
  2. Push reset button and power on the device
  3. Open u-boot HTTP recovery at http://192.168.1.1
  4. Upload latest stock firmware and wait until the device is rebooted

Note: The DTS expects OpenWrt to be running from the second rootfs
partition. u-boot on these devices hot-patches the DTS so running from the
first rootfs partition should also be possible. If you want to be save follow
the instructions above. u-boot HTTP recovery restores the device so that when
flashing OpenWrt from stock firmware it is flashed to the second rootfs
partition and the DTS matches.

Signed-off-by: Felix Matouschek <felix@matouschek.org>
2021-11-28 18:39:01 +01:00

146 lines
5.3 KiB
Makefile

include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/version.mk
PKG_NAME:=ipq-wifi
PKG_RELEASE:=1
PKG_FLAGS:=nonshared
include $(INCLUDE_DIR)/package.mk
define Build/Prepare
mkdir -p $(PKG_BUILD_DIR)
endef
define Build/Compile
endef
# Use ath10k-bdencoder from https://github.com/qca/qca-swiss-army-knife.git
# to generate the board-* files here.
#
# This is intended to be used on an interim basis until device-specific
# board data for new devices is available through the upstream compilation
#
# Please send a mail with your device-specific board files upstream.
# You can find instructions and examples on the linux-wireless wiki:
# <https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles>
ALLWIFIBOARDS:= \
8dev_habanero-dvk \
aruba_ap-303 \
avm_fritzrepeater-1200 \
buffalo_wtr-m2133hp \
cellc_rtl30vw \
devolo_magic-2-wifi-next \
dlink_dap2610 \
edgecore_ecw5410 \
edgecore_oap100 \
engenius_eap2200 \
engenius_emd1 \
engenius_emr3500 \
ezviz_cs-w3-wd1200g-eup \
glinet_gl-ap1300 \
glinet_gl-s1300 \
linksys_ea8300 \
linksys_mr8300-v0 \
luma_wrtq-329acn \
mikrotik_hap-ac2 \
mikrotik_hap-ac3 \
mikrotik_sxtsq-5-ac \
mobipromo_cm520-79f \
nec_wg2600hp3 \
p2w_r619ac \
plasmacloud_pa1200 \
plasmacloud_pa2200 \
qxwlan_e2600ac \
teltonika_rutx
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
define Package/ipq-wifi-default
SUBMENU:=ath10k Board-Specific Overrides
SECTION:=firmware
CATEGORY:=Firmware
DEPENDS:=@(TARGET_ipq40xx||TARGET_ipq806x)
TITLE:=Custom Board
endef
define ipq-wifi-install-one-to
$(INSTALL_DIR) $(2)/lib/firmware/ath10k/$(3)/
$(INSTALL_DATA) $(1) $(2)/lib/firmware/ath10k/$(3)/board-2.bin
endef
define ipq-wifi-install-one
$(if $(filter $(suffix $(1)),.QCA4019 .qca4019),\
$(call ipq-wifi-install-one-to,$(1),$(2),QCA4019/hw1.0),\
$(if $(filter $(suffix $(1)),.QCA9888 .qca9888),\
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9888/hw2.0),\
$(if $(filter $(suffix $(1)),.QCA9984 .qca9984),\
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9984/hw1.0),\
$(error Unrecognized board-file suffix '$(suffix $(1))' for '$(1)')\
)))
endef
# Blank line required at end of above define due to foreach context
define generate-ipq-wifi-package
define Package/ipq-wifi-$(1)
$(call Package/ipq-wifi-default)
TITLE:=board-2.bin Overrides for $(2)
CONFLICTS:=$(PREV_BOARD)
endef
define Package/ipq-wifi-$(1)/description
The $(2) requires board-specific, reference ("cal") data
that is not yet present in the upstream wireless firmware distribution.
This package supplies board-2.bin file(s) that, in the interim,
overwrite those supplied by the ath10k-firmware-* packages.
This is package is only necessary for the $(2).
Do not install it for any other device!
endef
define Package/ipq-wifi-$(1)/install-overlay
$$$$(foreach IPQ_WIFI_BOARD_FILE,$$$$(wildcard board-$(1).*),\
$$$$(call ipq-wifi-install-one,$$$$(IPQ_WIFI_BOARD_FILE),$$(1)))
endef
PREV_BOARD+=ipq-wifi-$(1)
endef
# Add board name to ALLWIFIBOARDS
# Place files in this directory as board-<devicename>.<qca4019|qca9888|qca9984>
# Add $(eval $(call generate-ipq-wifi-package,<devicename>,<display name>))
$(eval $(call generate-ipq-wifi-package,8dev_habanero-dvk,8devices Habanero DVK))
$(eval $(call generate-ipq-wifi-package,aruba_ap-303,Aruba AP-303))
$(eval $(call generate-ipq-wifi-package,avm_fritzrepeater-1200,AVM FRITZRepeater 1200))
$(eval $(call generate-ipq-wifi-package,buffalo_wtr-m2133hp,Buffalo WTR-M2133HP))
$(eval $(call generate-ipq-wifi-package,cellc_rtl30vw, Cell C RTL30VW))
$(eval $(call generate-ipq-wifi-package,devolo_magic-2-wifi-next,devolo Magic 2 WiFi next))
$(eval $(call generate-ipq-wifi-package,dlink_dap2610,D-Link DAP-2610))
$(eval $(call generate-ipq-wifi-package,edgecore_ecw5410,Edgecore ECW5410))
$(eval $(call generate-ipq-wifi-package,edgecore_oap100,Edgecore OAP100))
$(eval $(call generate-ipq-wifi-package,engenius_eap2200,EnGenius EAP2200))
$(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1))
$(eval $(call generate-ipq-wifi-package,engenius_emr3500,EnGenius EMR3500))
$(eval $(call generate-ipq-wifi-package,ezviz_cs-w3-wd1200g-eup,EZVIZ CS-W3-WD1200G EUP))
$(eval $(call generate-ipq-wifi-package,glinet_gl-ap1300,GL.iNet GL-AP1300))
$(eval $(call generate-ipq-wifi-package,glinet_gl-s1300,GL.iNet GL-S1300))
$(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
$(eval $(call generate-ipq-wifi-package,linksys_mr8300-v0,Linksys MR8300))
$(eval $(call generate-ipq-wifi-package,luma_wrtq-329acn,Luma WRTQ-329ACN))
$(eval $(call generate-ipq-wifi-package,mikrotik_hap-ac2,Mikrotik hAP ac2))
$(eval $(call generate-ipq-wifi-package,mikrotik_hap-ac3,Mikrotik hAP ac3))
$(eval $(call generate-ipq-wifi-package,mikrotik_sxtsq-5-ac,MikroTik SXTsq 5 ac))
$(eval $(call generate-ipq-wifi-package,mobipromo_cm520-79f,MobiPromo CM520-79F))
$(eval $(call generate-ipq-wifi-package,nec_wg2600hp3,NEC Platforms WG2600HP3))
$(eval $(call generate-ipq-wifi-package,p2w_r619ac,P&W R619AC))
$(eval $(call generate-ipq-wifi-package,plasmacloud_pa1200,Plasma Cloud PA1200))
$(eval $(call generate-ipq-wifi-package,plasmacloud_pa2200,Plasma Cloud PA2200))
$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC))
$(eval $(call generate-ipq-wifi-package,teltonika_rutx,Teltonika RUTX))
$(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))