mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-25 08:21:14 +00:00
1cc3b95efc
This patch adds support for the Teltonika RUTX10. This device is an industrial DIN-rail router with 4 ethernet ports, 2.4G/5G dualband WiFi, Bluetooth, a USB 2.0 port and two GPIOs. The RUTX series devices are very similiar so common parts of the DTS are kept in a DTSI file. They are based on the QCA AP-DK01.1-C1 dev board. See https://teltonika-networks.com/product/rutx10 for more info. Hardware: SoC: Qualcomm IPQ4018 RAM: 256MB DDR3 SPI Flash 1: XTX XT25F128B (16MB, NOR) SPI Flash 2: XTX XT26G02AWS (256MB, NAND) Ethernet: Built-in IPQ4018 (SoC, QCA8075), 4x 10/100/1000 ports WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n Wifi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac USB Hub: Genesys Logic GL852GT Bluetooth: Qualcomm CSR8510 (A10U) LED/GPIO controller: STM32F030 with custom firmware Buttons: Reset button Leds: Power (green, cannot be controlled) WiFi 2.4G activity (green) WiFi 5G activity (green) MACs Details verified with the stock firmware: eth0: Partition 0:CONFIG Offset: 0x0 eth1: = eth0 + 1 radio0 (2.4 GHz): = eth0 + 2 radio1 (5.0 GHz): = eth0 + 3 Label MAC address is from eth0. The LED/GPIO controller needs a separate kernel driver to function. The driver was extracted from the Teltonika GPL sources and can be found at following feed: https://github.com/0xFelix/teltonika-rutx-openwrt USB detection of the bluetooth interface is sometimes a bit flaky. When not detected power cycle the device. When the bluetooth interface was detected properly it can be used with bluez / bluetoothctl. Flash instructions via stock web interface (sysupgrade based): 1. Set PC to fixed ip address 192.168.1.100 2. Push reset button and power on the device 3. Open u-boot HTTP recovery at http://192.168.1.1 4. Upload latest stock firmware and wait until the device is rebooted 5. Open stock web interface at http://192.168.1.1 6. Set some password so the web interface is happy 7. Go to firmware upgrade settings 8. Choose openwrt-ipq40xx-generic-teltonika_rutx10-squashfs-nand-factory.ubi 9. Set 'Keep settings' to off 10. Click update, when warned that it is not a signed image proceed Return to stock firmware: 1. Set PC to fixed ip address 192.168.1.100 2. Push reset button and power on the device 3. Open u-boot HTTP recovery at http://192.168.1.1 4. Upload latest stock firmware and wait until the device is rebooted Note: The DTS expects OpenWrt to be running from the second rootfs partition. u-boot on these devices hot-patches the DTS so running from the first rootfs partition should also be possible. If you want to be save follow the instructions above. u-boot HTTP recovery restores the device so that when flashing OpenWrt from stock firmware it is flashed to the second rootfs partition and the DTS matches. Signed-off-by: Felix Matouschek <felix@matouschek.org> |
||
|---|---|---|
| .. | ||
| board-8dev_habanero-dvk.qca4019 | ||
| board-aruba_ap-303.qca4019 | ||
| board-avm_fritzrepeater-1200.qca4019 | ||
| board-buffalo_wtr-m2133hp.qca4019 | ||
| board-buffalo_wtr-m2133hp.qca9984 | ||
| board-cellc_rtl30vw.qca4019 | ||
| board-devolo_magic-2-wifi-next.qca4019 | ||
| board-dlink_dap2610.qca4019 | ||
| board-edgecore_ecw5410.qca9984 | ||
| board-edgecore_oap100.qca4019 | ||
| board-engenius_eap2200.qca4019 | ||
| board-engenius_eap2200.qca9888 | ||
| board-engenius_emd1.qca4019 | ||
| board-engenius_emr3500.qca4019 | ||
| board-ezviz_cs-w3-wd1200g-eup.qca4019 | ||
| board-glinet_gl-ap1300.qca4019 | ||
| board-glinet_gl-s1300.qca4019 | ||
| board-linksys_ea8300.qca4019 | ||
| board-linksys_ea8300.qca9888 | ||
| board-linksys_mr8300-v0.qca4019 | ||
| board-linksys_mr8300-v0.qca9888 | ||
| board-luma_wrtq-329acn.qca4019 | ||
| board-mikrotik_hap-ac2.qca4019 | ||
| board-mikrotik_hap-ac3.qca4019 | ||
| board-mikrotik_sxtsq-5-ac.qca4019 | ||
| board-mobipromo_cm520-79f.qca4019 | ||
| board-nec_wg2600hp3.qca9984 | ||
| board-p2w_r619ac.qca4019 | ||
| board-plasmacloud_pa1200.qca4019 | ||
| board-plasmacloud_pa2200.qca4019 | ||
| board-plasmacloud_pa2200.qca9888 | ||
| board-qxwlan_e2600ac.qca4019 | ||
| board-teltonika_rutx.qca4019 | ||
| Makefile | ||