mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-25 08:21:14 +00:00
88ca372b5a
Refreshed all patches. Remove upstreamed: - 0004-boot-sq201-from-sda1.patch - 500-v4.20-ubifs-Fix-default-compression-selection-in-ubifs.patch - 0003-usb-dwc2-use-a-longer-core-rest-timeout-in-dwc2_core.patch Altered patches: - 0011-ARM-dts-Fix-up-SQ201-flash-access.patch - 400-mtd-add-rootfs-split-support.patch - 0101-pci-mediatek-backport-fix-pcie.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
154 lines
4.5 KiB
Diff
154 lines
4.5 KiB
Diff
From 928681e6b46cb70317f7721aae8435ea89fcfd80 Mon Sep 17 00:00:00 2001
|
|
From: Linus Walleij <linus.walleij@linaro.org>
|
|
Date: Thu, 11 Oct 2018 20:06:23 +0200
|
|
Subject: [PATCH] ARM: dts: Enable Gemini flash access
|
|
|
|
Some Gemini platforms have a parallel NOR flash which conflicts
|
|
with use cases reusing some of the flash lines (such as CE1)
|
|
for GPIO.
|
|
|
|
Fix this on the D-Link DIR-685 and Itian SQ201 by creating
|
|
"enabled" and "disabled" states for the flash pin control
|
|
handle, and rely on the flash handling code to switch this
|
|
in and out when accessed so these lines can be used
|
|
for GPIO when flash is not accessed, and enable flash
|
|
access.
|
|
|
|
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
---
|
|
arch/arm/boot/dts/gemini-dlink-dir-685.dts | 33 +++++++++++++++-------
|
|
arch/arm/boot/dts/gemini-sq201.dts | 31 +++++++++++---------
|
|
2 files changed, 40 insertions(+), 24 deletions(-)
|
|
|
|
--- a/arch/arm/boot/dts/gemini-dlink-dir-685.dts
|
|
+++ b/arch/arm/boot/dts/gemini-dlink-dir-685.dts
|
|
@@ -64,7 +64,6 @@
|
|
gpio-sck = <&gpio1 5 GPIO_ACTIVE_HIGH>;
|
|
gpio-miso = <&gpio1 8 GPIO_ACTIVE_HIGH>;
|
|
gpio-mosi = <&gpio1 7 GPIO_ACTIVE_HIGH>;
|
|
- /* Collides with pflash CE1, not so cool */
|
|
cs-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
|
|
num-chipselects = <1>;
|
|
|
|
@@ -253,15 +252,18 @@
|
|
soc {
|
|
flash@30000000 {
|
|
/*
|
|
- * Flash access is by default disabled, because it
|
|
- * collides with the Chip Enable signal for the display
|
|
- * panel, that reuse the parallel flash Chip Select 1
|
|
- * (CS1). Enabling flash makes graphics stop working.
|
|
- *
|
|
- * We might be able to hack around this by letting
|
|
- * GPIO poke around in the flash controller registers.
|
|
+ * Flash access collides with the Chip Enable signal for
|
|
+ * the display panel, that reuse the parallel flash Chip
|
|
+ * Select 1 (CS1). We switch the pin control state so we
|
|
+ * enable these pins for flash access only when we need
|
|
+ * then, and when disabled they can be used for GPIO which
|
|
+ * is what the display panel needs.
|
|
*/
|
|
- /* status = "okay"; */
|
|
+ status = "okay";
|
|
+ pinctrl-names = "enabled", "disabled";
|
|
+ pinctrl-0 = <&pflash_default_pins>;
|
|
+ pinctrl-1 = <&pflash_disabled_pins>;
|
|
+
|
|
/* 32MB of flash */
|
|
reg = <0x30000000 0x02000000>;
|
|
|
|
@@ -327,7 +329,6 @@
|
|
"gpio0cgrp",
|
|
"gpio0egrp",
|
|
"gpio0fgrp",
|
|
- "gpio0ggrp",
|
|
"gpio0hgrp";
|
|
};
|
|
};
|
|
@@ -342,6 +343,18 @@
|
|
groups = "gpio1bgrp";
|
|
};
|
|
};
|
|
+ /*
|
|
+ * These GPIO groups will be mapped in over some
|
|
+ * of the flash pins when the flash is not in
|
|
+ * active use.
|
|
+ */
|
|
+ pflash_disabled_pins: pinctrl-pflash-disabled {
|
|
+ mux {
|
|
+ function = "gpio0";
|
|
+ groups = "gpio0ggrp", "gpio0igrp", "gpio0jgrp",
|
|
+ "gpio0kgrp";
|
|
+ };
|
|
+ };
|
|
pinctrl-gmii {
|
|
mux {
|
|
function = "gmii";
|
|
--- a/arch/arm/boot/dts/gemini-sq201.dts
|
|
+++ b/arch/arm/boot/dts/gemini-sq201.dts
|
|
@@ -41,14 +41,12 @@
|
|
compatible = "gpio-leds";
|
|
led-green-info {
|
|
label = "sq201:green:info";
|
|
- /* Conflict with parallel flash */
|
|
gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
|
|
default-state = "on";
|
|
linux,default-trigger = "heartbeat";
|
|
};
|
|
led-green-usb {
|
|
label = "sq201:green:usb";
|
|
- /* Conflict with parallel and NAND flash */
|
|
gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
linux,default-trigger = "usb-host";
|
|
@@ -126,15 +124,10 @@
|
|
|
|
soc {
|
|
flash@30000000 {
|
|
- /*
|
|
- * Flash access can be enabled, with the side effect
|
|
- * of disabling access to GPIO LED on GPIO0[20] which
|
|
- * reuse one of the parallel flash chip select lines.
|
|
- * Also the default firmware on the machine has the
|
|
- * problem that since it uses the flash, the two LEDS
|
|
- * on the right become numb.
|
|
- */
|
|
- /* status = "okay"; */
|
|
+ status = "okay";
|
|
+ pinctrl-names = "enabled", "disabled";
|
|
+ pinctrl-0 = <&pflash_default_pins>;
|
|
+ pinctrl-1 = <&pflash_disabled_pins>;
|
|
/* 16MB of flash */
|
|
reg = <0x30000000 0x01000000>;
|
|
|
|
@@ -157,9 +150,7 @@
|
|
mux {
|
|
function = "gpio0";
|
|
groups = "gpio0fgrp",
|
|
- "gpio0ggrp",
|
|
- "gpio0hgrp",
|
|
- "gpio0kgrp";
|
|
+ "gpio0hgrp";
|
|
};
|
|
};
|
|
/*
|
|
@@ -172,6 +163,18 @@
|
|
groups = "gpio1dgrp";
|
|
};
|
|
};
|
|
+ /*
|
|
+ * These GPIO groups will be mapped in over some
|
|
+ * of the flash pins when the flash is not in
|
|
+ * active use.
|
|
+ */
|
|
+ pflash_disabled_pins: pinctrl-pflash-disabled {
|
|
+ mux {
|
|
+ function = "gpio0";
|
|
+ groups = "gpio0ggrp", "gpio0igrp", "gpio0jgrp",
|
|
+ "gpio0kgrp";
|
|
+ };
|
|
+ };
|
|
pinctrl-gmii {
|
|
mux {
|
|
function = "gmii";
|