mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-23 07:22:33 +00:00
67ce9aedd6
This patch adds support for the Check Point L-50 from 600/1100 series routers. Specification: -CPU: Marvell Kirkwood 88F6281 1200MHz -RAM: 512MB -Flash: NAND 512MB -WiFi: mPCIe card based on Atheros AR9287 b/g/n -WAN: 1 Gigabit Port (Marvell 88E1116R PHY) -LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+4)) -USB: 2x USB2.0 -Express card slot -SD card slot -Serial console: RJ-45 115200 8n1 -Unsupported DSL Known issues: -DSL not supported -Expresscard not tested Installation: Step one -> backup: make backup u-boot and env for revert stock posibility make backup dsl_mac_addr, dmz_mac_addr, eth1addr, ethaddr and all lanX_mac_addr Step two -> Use kwboot tool to upload openwrt u-boot to RAM: run kwboot: "kwboot -B 115200 /dev/ttyUSB0 -b u-boot.kwb -p -t" end start u-boot Step three -> Restore macs (e.g. below): setenv eth1addr 00:1C:XX:XX:XX:6C setenv ethaddr 00:1C:XX:XX:XX:6B setenv lan1_mac_addr 00:1C:XX:XX:XX:6C setenv lan2_mac_addr 00:1C:XX:XX:XX:6D setenv lan3_mac_addr 00:1C:XX:XX:XX:6E setenv lan4_mac_addr 00:1C:XX:XX:XX:6F setenv lan5_mac_addr 00:1C:XX:XX:XX:70 setenv lan6_mac_addr 00:1C:XX:XX:XX:71 setenv lan7_mac_addr 00:1C:XX:XX:XX:72 setenv lan8_mac_addr 00:1C:XX:XX:XX:73 setenv dmz_mac_addr 00:1C:XX:XX:XX:74 setenv dsl_mac_addr 00:1C:XX:XX:XX:75 Step four -> flash u-boot: mw 0x0800000 0xffff 0x100000 nand erase 0x0 100000 tftp 0x0800000 openwrt-kirkwood-l50-u-boot.kwb nand write 0x0800000 0x0 0x100000 saveenv Step five -> run initramfs image: tftpboot 0x02000000 openwrt.bin; bootm 0x02000000; Step six -> install sysupgrade OpenWrt image: copy to /tmp/ sysupgrade image run sysupgrade Back to stock: Restore original u-boot end env. Install factory image via stock u-boot. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
48 lines
965 B
Diff
48 lines
965 B
Diff
--- a/arch/arm/boot/dts/kirkwood-l-50.dts
|
|
+++ b/arch/arm/boot/dts/kirkwood-l-50.dts
|
|
@@ -18,6 +18,13 @@
|
|
reg = <0x00000000 0x20000000>;
|
|
};
|
|
|
|
+ aliases {
|
|
+ led-boot = &led_status_green;
|
|
+ led-failsafe = &led_status_red;
|
|
+ led-running = &led_status_green;
|
|
+ led-upgrade = &led_status_red;
|
|
+ };
|
|
+
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8";
|
|
stdout-path = &uart0;
|
|
@@ -95,12 +102,12 @@
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
- status_green {
|
|
+ led_status_green: status_green {
|
|
label = "l-50:green:status";
|
|
gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
- status_red {
|
|
+ led_status_red: status_red {
|
|
label = "l-50:red:status";
|
|
gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
|
|
};
|
|
@@ -349,13 +356,8 @@
|
|
};
|
|
|
|
partition@100000 {
|
|
- label = "kernel-1";
|
|
- reg = <0x00100000 0x00800000>;
|
|
- };
|
|
-
|
|
- partition@900000 {
|
|
- label = "rootfs-1";
|
|
- reg = <0x00900000 0x07100000>;
|
|
+ label = "ubi";
|
|
+ reg = <0x00100000 0x07900000>;
|
|
};
|
|
|
|
partition@7a00000 {
|