mirror of
https://github.com/openwrt/openwrt.git
synced 2025-02-21 01:41:41 +00:00
67ce9aedd6
This patch adds support for the Check Point L-50 from 600/1100 series routers. Specification: -CPU: Marvell Kirkwood 88F6281 1200MHz -RAM: 512MB -Flash: NAND 512MB -WiFi: mPCIe card based on Atheros AR9287 b/g/n -WAN: 1 Gigabit Port (Marvell 88E1116R PHY) -LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+4)) -USB: 2x USB2.0 -Express card slot -SD card slot -Serial console: RJ-45 115200 8n1 -Unsupported DSL Known issues: -DSL not supported -Expresscard not tested Installation: Step one -> backup: make backup u-boot and env for revert stock posibility make backup dsl_mac_addr, dmz_mac_addr, eth1addr, ethaddr and all lanX_mac_addr Step two -> Use kwboot tool to upload openwrt u-boot to RAM: run kwboot: "kwboot -B 115200 /dev/ttyUSB0 -b u-boot.kwb -p -t" end start u-boot Step three -> Restore macs (e.g. below): setenv eth1addr 00:1C:XX:XX:XX:6C setenv ethaddr 00:1C:XX:XX:XX:6B setenv lan1_mac_addr 00:1C:XX:XX:XX:6C setenv lan2_mac_addr 00:1C:XX:XX:XX:6D setenv lan3_mac_addr 00:1C:XX:XX:XX:6E setenv lan4_mac_addr 00:1C:XX:XX:XX:6F setenv lan5_mac_addr 00:1C:XX:XX:XX:70 setenv lan6_mac_addr 00:1C:XX:XX:XX:71 setenv lan7_mac_addr 00:1C:XX:XX:XX:72 setenv lan8_mac_addr 00:1C:XX:XX:XX:73 setenv dmz_mac_addr 00:1C:XX:XX:XX:74 setenv dsl_mac_addr 00:1C:XX:XX:XX:75 Step four -> flash u-boot: mw 0x0800000 0xffff 0x100000 nand erase 0x0 100000 tftp 0x0800000 openwrt-kirkwood-l50-u-boot.kwb nand write 0x0800000 0x0 0x100000 saveenv Step five -> run initramfs image: tftpboot 0x02000000 openwrt.bin; bootm 0x02000000; Step six -> install sysupgrade OpenWrt image: copy to /tmp/ sysupgrade image run sysupgrade Back to stock: Restore original u-boot end env. Install factory image via stock u-boot. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
This is the buildsystem for the OpenWrt Linux distribution.
To build your own firmware you need a Linux, BSD or MacOSX system (case
sensitive filesystem required). Cygwin is unsupported because of the lack
of a case sensitive file system.
You need gcc, binutils, bzip2, flex, python3.5+, perl, make, find, grep, diff,
unzip, gawk, getopt, subversion, libz-dev and libc headers installed.
1. Run "./scripts/feeds update -a" to obtain all the latest package definitions
defined in feeds.conf / feeds.conf.default
2. Run "./scripts/feeds install -a" to install symlinks for all obtained
packages into package/feeds/
3. Run "make menuconfig" to select your preferred configuration for the
toolchain, target system & firmware packages.
4. Run "make" to build your firmware. This will download all sources, build
the cross-compile toolchain and then cross-compile the Linux kernel & all
chosen applications for your target system.
Sunshine!
Your OpenWrt Community
http://www.openwrt.org