ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-20 14:13:16 +00:00
Code Issues Actions 1 Packages Projects Releases Wiki Activity
67ce9aedd6
openwrt/target/linux/kirkwood/image/Makefile
Pawel Dembicki 67ce9aedd6 kirkwood: add support for Check Point L-50 
This patch adds support for the Check Point L-50 from 600/1100 series
routers.

Specification:
-CPU: Marvell Kirkwood 88F6281 1200MHz
-RAM: 512MB
-Flash: NAND 512MB
-WiFi: mPCIe card based on Atheros AR9287 b/g/n
-WAN: 1 Gigabit Port (Marvell 88E1116R PHY)
-LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+4))
-USB: 2x USB2.0
-Express card slot
-SD card slot
-Serial console: RJ-45 115200 8n1
-Unsupported DSL

Known issues:
-DSL not supported
-Expresscard not tested

Installation:

Step one -> backup:
make backup u-boot and env for revert stock posibility
make backup dsl_mac_addr, dmz_mac_addr, eth1addr, ethaddr and all lanX_mac_addr

Step two -> Use kwboot tool to upload openwrt u-boot to RAM:

run kwboot: "kwboot -B 115200 /dev/ttyUSB0 -b u-boot.kwb -p -t"
end start u-boot

Step three -> Restore macs (e.g. below):
setenv eth1addr 00:1C:XX:XX:XX:6C
setenv ethaddr 00:1C:XX:XX:XX:6B
setenv lan1_mac_addr 00:1C:XX:XX:XX:6C
setenv lan2_mac_addr 00:1C:XX:XX:XX:6D
setenv lan3_mac_addr 00:1C:XX:XX:XX:6E
setenv lan4_mac_addr 00:1C:XX:XX:XX:6F
setenv lan5_mac_addr 00:1C:XX:XX:XX:70
setenv lan6_mac_addr 00:1C:XX:XX:XX:71
setenv lan7_mac_addr 00:1C:XX:XX:XX:72
setenv lan8_mac_addr 00:1C:XX:XX:XX:73
setenv dmz_mac_addr 00:1C:XX:XX:XX:74
setenv dsl_mac_addr 00:1C:XX:XX:XX:75

Step four -> flash u-boot:
mw 0x0800000 0xffff 0x100000
nand erase 0x0 100000
tftp 0x0800000 openwrt-kirkwood-l50-u-boot.kwb
nand write 0x0800000 0x0 0x100000
saveenv

Step five -> run initramfs image:

tftpboot 0x02000000 openwrt.bin; bootm 0x02000000;

Step six -> install sysupgrade OpenWrt image:

copy to /tmp/ sysupgrade image
run sysupgrade

Back to stock:
Restore original u-boot end env.
Install factory image via stock u-boot.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-07-11 13:33:28 +02:00

180 lines
4.8 KiB
Makefile
Raw Blame History

#
# Copyright (C) 2009-2013 OpenWrt.org
#
# This is free software, licensed under the GNU General Public License v2.
# See /LICENSE for more information.
#
include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk
KERNEL_LOADADDR:=0x8000
define Device/Default
PROFILES := Default
DEVICE_DTS = $$(if $$(BOARD_NAME),kirkwood-$$(BOARD_NAME),)
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
KERNEL := kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
KERNEL_SUFFIX := -uImage
KERNEL_IN_UBI := 1
PAGESIZE := 2048
SUBPAGESIZE := 512
BLOCKSIZE := 128k
IMAGES := sysupgrade.bin factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-ubi
SUPPORTED_DEVICES = $(subst _,$(comma),$(1)) $$(BOARD_NAME)
endef
define Device/checkpoint_l-50
DEVICE_VENDOR := Check Point
DEVICE_MODEL := L-50
DEVICE_DTS := kirkwood-l-50
DEVICE_PACKAGES := kmod-ath9k kmod-gpio-button-hotplug kmod-mvsdio \
kmod-rtc-s35390a kmod-usb-ledtrig-usbport wpad-basic
IMAGES := sysupgrade.bin
endef
TARGET_DEVICES += checkpoint_l-50
define Device/cisco_on100
DEVICE_VENDOR := Cisco Systems
DEVICE_MODEL := ON100
KERNEL_SIZE := 5376k
KERNEL_IN_UBI :=
UBINIZE_OPTS := -E 5
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
BOARD_NAME := on100
DEVICE_PACKAGES := kmod-mvsdio
endef
TARGET_DEVICES += cisco_on100
define Device/cloudengines_pogoe02
DEVICE_VENDOR := Cloud Engines
DEVICE_MODEL := Pogoplug E02
BOARD_NAME := pogo_e02
endef
TARGET_DEVICES += cloudengines_pogoe02
define Device/cloudengines_pogoplugv4
DEVICE_VENDOR := Cloud Engines
DEVICE_MODEL := Pogoplug V4
DEVICE_DTS := kirkwood-pogoplug-series-4
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 kmod-mvsdio kmod-usb3 \
kmod-gpio-button-hotplug
endef
TARGET_DEVICES += cloudengines_pogoplugv4
define Device/iom_iconnect-1.1
DEVICE_VENDOR := Iomega
DEVICE_MODEL := Iconnect
BOARD_NAME := iconnect
endef
TARGET_DEVICES += iom_iconnect-1.1
define Device/iom_ix2-200
DEVICE_VENDOR := Iomega
DEVICE_MODEL := StorCenter ix2-200
DEVICE_DTS := kirkwood-iomega_ix2_200
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 \
kmod-gpio-button-hotplug kmod-hwmon-lm63
PAGESIZE := 512
SUBPAGESIZE := 256
BLOCKSIZE := 16k
KERNEL_SIZE := 3072k
KERNEL_IN_UBI :=
UBINIZE_OPTS := -E 5
IMAGE_SIZE := 31744k
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
check-size
endef
TARGET_DEVICES += iom_ix2-200
define Device/linksys_audi
DEVICE_VENDOR := Linksys
DEVICE_MODEL := EA3500 (Audi)
DEVICE_PACKAGES := kmod-mwl8k wpad-basic kmod-gpio-button-hotplug
PAGESIZE := 512
SUBPAGESIZE := 256
BLOCKSIZE := 16k
KERNEL_SIZE := 2624k
KERNEL_IN_UBI :=
UBINIZE_OPTS := -E 5
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
BOARD_NAME := linksys-audi
endef
TARGET_DEVICES += linksys_audi
define Device/linksys_viper
DEVICE_VENDOR := Linksys
DEVICE_MODEL := E4200v2 / EA4500 (Viper)
DEVICE_PACKAGES := kmod-mwl8k wpad-basic kmod-gpio-button-hotplug
KERNEL_SIZE := 2688k
KERNEL_IN_UBI :=
UBINIZE_OPTS := -E 5
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
BOARD_NAME := linksys-viper
endef
TARGET_DEVICES += linksys_viper
define Device/raidsonic_ib-nas62x0
DEVICE_VENDOR := RaidSonic
DEVICE_MODEL := ICY BOX IB-NAS62x0
BOARD_NAME := ib62x0
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4
endef
TARGET_DEVICES += raidsonic_ib-nas62x0
define Device/seagate_dockstar
DEVICE_VENDOR := Seagate
DEVICE_MODEL := FreeAgent Dockstar
BOARD_NAME := dockstar
endef
TARGET_DEVICES += seagate_dockstar
define Device/seagate_goflexnet
DEVICE_VENDOR := Seagate
DEVICE_MODEL := GoFlexNet
BOARD_NAME := goflexnet
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4
endef
TARGET_DEVICES += seagate_goflexnet
define Device/seagate_goflexhome
DEVICE_VENDOR := Seagate
DEVICE_MODEL := GoFlexHome
BOARD_NAME := goflexhome
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4
endef
TARGET_DEVICES += seagate_goflexhome
define Device/zyxel_nsa310b
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := NSA310b
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-r8169 kmod-fs-ext4 \
kmod-gpio-button-hotplug kmod-hwmon-lm85
BOARD_NAME := nsa310b
endef
TARGET_DEVICES += zyxel_nsa310b
define Device/zyxel_nsa310s
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := NSA310S
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 kmod-gpio-button-hotplug
DEVICE_DTS := kirkwood-nsa310s
endef
TARGET_DEVICES += zyxel_nsa310s
define Device/zyxel_nsa325
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := NSA325
DEVICE_VARIANT := v1/v2
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 \
kmod-gpio-button-hotplug kmod-rtc-pcf8563 kmod-usb3
BOARD_NAME := nsa325
endef
TARGET_DEVICES += zyxel_nsa325
$(eval $(call BuildImage))
Reference in New Issue View Git Blame Copy Permalink