mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-25 00:11:13 +00:00
a4e2766a5b
NEC Aterm WF1200CR is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on QCA9561. Specification: - SoC : Qualcomm Atheros QCA9561 - RAM : DDR2 128 MiB (W971GG6SB-25) - Flash : SPI-NOR 8 MiB (MX25L6433FM2I-08G) - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : QCA9561 (SoC) - 5 GHz : QCA9888 - Ethernet : 2x 10/100 Mbps - Switch : QCA9561 (SoC) - LEDs/Keys : 8x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - JP1: Vcc, GND, NC, TX, RX from "JP1" marking - 115200n8 - Power : 12 VDC, 0.9 A Flash instruction using factory image (stock: < v1.3.2): 1. Boot WF1200CR normally with "Router" mode 2. Access to "http://192.168.10.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Alternate flash instruction using initramfs image (stock: >= v1.3.2): 1. Prepare the TFTP server with the IP address 192.168.1.10 and place the OpenWrt initramfs image to the TFTP directory with the name "0101A8C0.img" 2. Connect serial console to WF1200CR 3. Boot WF1200CR and interrupt with any key after the message "Hit any key to stop autoboot: 2", the U-Boot starts telnetd after the message "starting telnetd server from server 192.168.1.1" 4. login the telnet (address: 192.168.1.1) 5. Perform the following commands to modify "bootcmd" variable temporary and check the value (to ignore the limitation of available commands, "tp; " command at the first is required as dummy, and the output of "printenv" is printed on the serial console) tp; set bootcmd 'set autostart yes; tftpboot' tp; printenv 6. Save the modified variable with the following command and reset device tp; saveenv tp; reset 7. The U-Boot downloads initramfs image from TFTP server and boots it 8. On initramfs image, download the sysupgrade image to the device and perform the following commands to erase stock firmware and sysupgrade mtd erase firmware sysupgrade <sysupgrade image> 9. After the rebooting by completion of sysupgrade, start U-Boot telnetd and login with the same way above (3, 4) 10. Perform the following commands to reset "bootcmd" variable to the default and reset the device tp; run seattle tp; reset (the contents of "seattle": setenv bootcmd 'bootm 0x9f070040' && saveenv) 11. Wait booting-up the device Known issues: - the following 6x LEDs are connected to the gpio controller on QCA9888 chip and the implementation of control via the controller is missing in ath10k/ath10k-ct - "ACTIVE" (Red/Green) - "2.4GHz" (Red/Green) - "5GHz" (Red/Green) Note: - after the version v1.3.2 of stock firmware, "offline update" by uploading image by user is deleted and the factory image cannot be used - the U-Boot on WF1200CR doesn't configure the port-side LEDs on WAN/LAN and the configuration is required on OpenWrt - gpio-hog: set the direction of GPIO 14(WAN)/19(LAN) to output - pinmux: set GPIO 14/19 as switch-controlled LEDs Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2353 lines
64 KiB
Makefile
2353 lines
64 KiB
Makefile
include ./common-buffalo.mk
|
|
include ./common-netgear.mk
|
|
include ./common-senao.mk
|
|
include ./common-tp-link.mk
|
|
include ./common-yuncore.mk
|
|
|
|
DEVICE_VARS += ADDPATTERN_ID ADDPATTERN_VERSION
|
|
DEVICE_VARS += SEAMA_SIGNATURE SEAMA_MTDBLOCK
|
|
DEVICE_VARS += KERNEL_INITRAMFS_PREFIX DAP_SIGNATURE
|
|
DEVICE_VARS += EDIMAX_HEADER_MAGIC EDIMAX_HEADER_MODEL
|
|
DEVICE_VARS += OPENMESH_CE_TYPE
|
|
|
|
define Build/add-elecom-factory-initramfs
|
|
$(eval edimax_model=$(word 1,$(1)))
|
|
$(eval product=$(word 2,$(1)))
|
|
|
|
$(STAGING_DIR_HOST)/bin/mkedimaximg \
|
|
-b -s CSYS -m $(edimax_model) \
|
|
-f 0x70000 -S 0x01100000 \
|
|
-i $@ -o $@.factory
|
|
|
|
$(call Build/elecom-product-header,$(product) $@.factory)
|
|
|
|
if [ "$$(stat -c%s $@.factory)" -le $$(($(subst k,* 1024,$(subst m, * 1024k,$(IMAGE_SIZE))))) ]; then \
|
|
mv $@.factory $(BIN_DIR)/$(KERNEL_INITRAMFS_PREFIX)-factory.bin; \
|
|
else \
|
|
echo "WARNING: initramfs kernel image too big, cannot generate factory image" >&2; \
|
|
fi
|
|
endef
|
|
|
|
define Build/addpattern
|
|
-$(STAGING_DIR_HOST)/bin/addpattern -B $(ADDPATTERN_ID) \
|
|
-v v$(ADDPATTERN_VERSION) -i $@ -o $@.new
|
|
-mv "$@.new" "$@"
|
|
endef
|
|
|
|
define Build/append-md5sum-bin
|
|
$(MKHASH) md5 $@ | sed 's/../\\\\x&/g' |\
|
|
xargs echo -ne >> $@
|
|
endef
|
|
|
|
define Build/cybertan-trx
|
|
@echo -n '' > $@-empty.bin
|
|
-$(STAGING_DIR_HOST)/bin/trx -o $@.new \
|
|
-f $(IMAGE_KERNEL) -F $@-empty.bin \
|
|
-x 32 -a 0x10000 -x -32 -f $@
|
|
-mv "$@.new" "$@"
|
|
-rm $@-empty.bin
|
|
endef
|
|
|
|
define Build/edimax-headers
|
|
$(eval edimax_magic=$(word 1,$(1)))
|
|
$(eval edimax_model=$(word 2,$(1)))
|
|
|
|
$(STAGING_DIR_HOST)/bin/edimax_fw_header -M $(edimax_magic) -m $(edimax_model)\
|
|
-v $(VERSION_DIST)$(firstword $(subst +, , $(firstword $(subst -, ,$(REVISION))))) \
|
|
-n "uImage" \
|
|
-i $(KDIR)/loader-$(DEVICE_NAME).uImage \
|
|
-o $@.uImage
|
|
$(STAGING_DIR_HOST)/bin/edimax_fw_header -M $(edimax_magic) -m $(edimax_model)\
|
|
-v $(VERSION_DIST)$(firstword $(subst +, , $(firstword $(subst -, ,$(REVISION))))) \
|
|
-n "rootfs" \
|
|
-i $@ \
|
|
-o $@.rootfs
|
|
cat $@.uImage $@.rootfs > $@
|
|
rm -rf $@.uImage $@.rootfs
|
|
endef
|
|
|
|
define Build/mkdapimg2
|
|
$(STAGING_DIR_HOST)/bin/mkdapimg2 \
|
|
-i $@ -o $@.new \
|
|
-s $(DAP_SIGNATURE) \
|
|
-v $(VERSION_DIST)-$(firstword $(subst +, , \
|
|
$(firstword $(subst -, ,$(REVISION))))) \
|
|
-r Default \
|
|
$(if $(1),-k $(1))
|
|
mv $@.new $@
|
|
endef
|
|
|
|
define Build/mkmylofw_16m
|
|
$(eval device_id=$(word 1,$(1)))
|
|
$(eval revision=$(word 2,$(1)))
|
|
|
|
# On WPJ344, WPJ531, and WPJ563, the default boot command tries 0x9f680000
|
|
# first and fails if the remains of the stock image are sill there
|
|
# - resulting in an infinite boot loop.
|
|
# The size parameter is grown to have that block deleted if the firmware
|
|
# isn't big enough by itself.
|
|
|
|
let \
|
|
size="$$(stat -c%s $@)" \
|
|
pad="$(subst k,* 1024,$(BLOCKSIZE))" \
|
|
pad="(pad - (size % pad)) % pad" \
|
|
newsize='size + pad' ; \
|
|
[ $$newsize -lt $$((0x660000)) ] && newsize=0x660000 ; \
|
|
$(STAGING_DIR_HOST)/bin/mkmylofw \
|
|
-B WPE72 -i 0x11f6:$(device_id):0x11f6:$(device_id) -r $(revision) \
|
|
-s 0x1000000 -p0x30000:$$newsize:al:0x80060000:"OpenWRT":$@ \
|
|
$@.new
|
|
@mv $@.new $@
|
|
endef
|
|
|
|
define Build/mkwrggimg
|
|
$(STAGING_DIR_HOST)/bin/mkwrggimg -b \
|
|
-i $@ -o $@.imghdr -d /dev/mtdblock/1 \
|
|
-m $(DEVICE_MODEL)-$(DEVICE_VARIANT) -s $(DAP_SIGNATURE) \
|
|
-v $(VERSION_DIST) -B $(REVISION)
|
|
mv $@.imghdr $@
|
|
endef
|
|
|
|
define Build/nec-enc
|
|
$(STAGING_DIR_HOST)/bin/nec-enc \
|
|
-i $@ -o $@.new -k $(1)
|
|
mv $@.new $@
|
|
endef
|
|
|
|
define Build/nec-fw
|
|
( stat -c%s $@ | tr -d "\n" | dd bs=16 count=1 conv=sync; ) >> $@
|
|
( \
|
|
echo -n -e "$(1)" | dd bs=16 count=1 conv=sync; \
|
|
echo -n "0.0.00" | dd bs=16 count=1 conv=sync; \
|
|
dd if=$@; \
|
|
) > $@.new
|
|
mv $@.new $@
|
|
endef
|
|
|
|
define Build/pisen_wmb001n-factory
|
|
-[ -f "$@" ] && \
|
|
mkdir -p "$@.tmp" && \
|
|
cp "$(KDIR)/loader-$(word 1,$(1)).uImage" "$@.tmp/uImage" && \
|
|
mv "$@" "$@.tmp/rootfs" && \
|
|
cp "bin/pisen_wmb001n_factory-header.bin" "$@" && \
|
|
$(TAR) -cp --numeric-owner --owner=0 --group=0 --mode=a-s --sort=name \
|
|
$(if $(SOURCE_DATE_EPOCH),--mtime="@$(SOURCE_DATE_EPOCH)") \
|
|
-C "$@.tmp" . | gzip -9n >> "$@" && \
|
|
rm -rf "$@.tmp"
|
|
endef
|
|
|
|
define Build/teltonika-fw-fake-checksum
|
|
# Teltonika U-Boot web based firmware upgrade/recovery routine compares
|
|
# 16 bytes from md5sum1[16] field in TP-Link v1 header (offset: 76 bytes
|
|
# from begin of the firmware file) with 16 bytes stored just before
|
|
# 0xdeadc0de marker. Values are only compared, MD5 sum is not verified.
|
|
let \
|
|
offs="$$(stat -c%s $@) - 20"; \
|
|
dd if=$@ bs=1 count=16 skip=76 |\
|
|
dd of=$@ bs=1 count=16 seek=$$offs conv=notrunc
|
|
endef
|
|
|
|
define Build/wrgg-pad-rootfs
|
|
$(STAGING_DIR_HOST)/bin/padjffs2 $(IMAGE_ROOTFS) -c 64 >>$@
|
|
endef
|
|
|
|
|
|
define Device/seama
|
|
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
|
|
KERNEL_INITRAMFS := $$(KERNEL) | seama
|
|
IMAGES += factory.bin
|
|
SEAMA_MTDBLOCK := 1
|
|
|
|
# 64 bytes offset:
|
|
# - 28 bytes seama_header
|
|
# - 36 bytes of META data (4-bytes aligned)
|
|
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | seama | pad-rootfs | \
|
|
append-metadata | check-size
|
|
IMAGE/factory.bin := $$(IMAGE/default) | pad-rootfs -x 64 | seama | \
|
|
seama-seal | check-size
|
|
SEAMA_SIGNATURE :=
|
|
endef
|
|
|
|
|
|
define Device/8dev_carambola2
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := 8devices
|
|
DEVICE_MODEL := Carambola2
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2
|
|
IMAGE_SIZE := 16000k
|
|
SUPPORTED_DEVICES += carambola2
|
|
endef
|
|
TARGET_DEVICES += 8dev_carambola2
|
|
|
|
define Device/8dev_lima
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := 8devices
|
|
DEVICE_MODEL := Lima
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
IMAGE_SIZE := 15616k
|
|
SUPPORTED_DEVICES += lima
|
|
endef
|
|
TARGET_DEVICES += 8dev_lima
|
|
|
|
define Device/adtran_bsap1880
|
|
SOC := ar7161
|
|
DEVICE_VENDOR := Adtran/Bluesocket
|
|
DEVICE_PACKAGES += -swconfig -uboot-envtools fconfig
|
|
KERNEL := kernel-bin | append-dtb | lzma | pad-to $$(BLOCKSIZE)
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb
|
|
IMAGE_SIZE := 11200k
|
|
IMAGES += kernel.bin rootfs.bin
|
|
IMAGE/kernel.bin := append-kernel
|
|
IMAGE/rootfs.bin := append-rootfs | pad-rootfs
|
|
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | \
|
|
check-size | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
endef
|
|
|
|
define Device/adtran_bsap1800-v2
|
|
$(Device/adtran_bsap1880)
|
|
DEVICE_MODEL := BSAP-1800
|
|
DEVICE_VARIANT := v2
|
|
endef
|
|
TARGET_DEVICES += adtran_bsap1800-v2
|
|
|
|
define Device/adtran_bsap1840
|
|
$(Device/adtran_bsap1880)
|
|
DEVICE_MODEL := BSAP-1840
|
|
endef
|
|
TARGET_DEVICES += adtran_bsap1840
|
|
|
|
define Device/airtight_c-75
|
|
SOC := qca9550
|
|
DEVICE_VENDOR := AirTight Networks
|
|
DEVICE_MODEL := C-75
|
|
DEVICE_ALT0_VENDOR := Mojo Networks
|
|
DEVICE_ALT0_MODEL := C-75
|
|
DEVICE_ALT1_VENDOR := WatchGuard
|
|
DEVICE_ALT1_MODEL := AP320
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2
|
|
IMAGE_SIZE := 32320k
|
|
KERNEL_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += airtight_c-75
|
|
|
|
define Device/alfa-network_ap121f
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := ALFA Network
|
|
DEVICE_MODEL := AP121F
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-usb-storage -swconfig
|
|
IMAGE_SIZE := 16064k
|
|
SUPPORTED_DEVICES += ap121f
|
|
endef
|
|
TARGET_DEVICES += alfa-network_ap121f
|
|
|
|
define Device/alfa-network_ap121fe
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := ALFA Network
|
|
DEVICE_MODEL := AP121FE
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-usb-gadget-eth -swconfig
|
|
IMAGE_SIZE := 16064k
|
|
endef
|
|
TARGET_DEVICES += alfa-network_ap121fe
|
|
|
|
define Device/alfa-network_n2q
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := ALFA Network
|
|
DEVICE_MODEL := N2Q
|
|
DEVICE_PACKAGES := kmod-i2c-gpio kmod-gpio-pcf857x kmod-usb2 \
|
|
kmod-usb-ledtrig-usbport rssileds
|
|
IMAGE_SIZE := 15872k
|
|
endef
|
|
TARGET_DEVICES += alfa-network_n2q
|
|
|
|
define Device/alfa-network_n5q
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := ALFA Network
|
|
DEVICE_MODEL := N5Q
|
|
DEVICE_PACKAGES := rssileds
|
|
IMAGE_SIZE := 15872k
|
|
SUPPORTED_DEVICES += n5q
|
|
endef
|
|
TARGET_DEVICES += alfa-network_n5q
|
|
|
|
define Device/alfa-network_pi-wifi4
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := ALFA Network
|
|
DEVICE_MODEL := Pi-WiFi4
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport -swconfig
|
|
IMAGE_SIZE := 15872k
|
|
endef
|
|
TARGET_DEVICES += alfa-network_pi-wifi4
|
|
|
|
define Device/alfa-network_r36a
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := ALFA Network
|
|
DEVICE_MODEL := R36A
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
|
|
IMAGE_SIZE := 15872k
|
|
SUPPORTED_DEVICES += r36a
|
|
endef
|
|
TARGET_DEVICES += alfa-network_r36a
|
|
|
|
define Device/allnet_all-wap02860ac
|
|
$(Device/senao_loader_okli)
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := ALLNET
|
|
DEVICE_MODEL := ALL-WAP02860AC
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
|
|
IMAGE_SIZE := 11584k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := senao-allwap02860ac
|
|
endef
|
|
TARGET_DEVICES += allnet_all-wap02860ac
|
|
|
|
define Device/arduino_yun
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := Arduino
|
|
DEVICE_MODEL := Yun
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-usb-ledtrig-usbport \
|
|
kmod-usb-storage block-mount -swconfig
|
|
IMAGE_SIZE := 15936k
|
|
SUPPORTED_DEVICES += arduino-yun
|
|
endef
|
|
TARGET_DEVICES += arduino_yun
|
|
|
|
define Device/aruba_ap-105
|
|
SOC := ar7161
|
|
DEVICE_VENDOR := Aruba
|
|
DEVICE_MODEL := AP-105
|
|
IMAGE_SIZE := 16000k
|
|
DEVICE_PACKAGES := kmod-i2c-gpio kmod-tpm-i2c-atmel
|
|
endef
|
|
TARGET_DEVICES += aruba_ap-105
|
|
|
|
define Device/avm
|
|
DEVICE_VENDOR := AVM
|
|
KERNEL := kernel-bin | append-dtb | lzma | eva-image
|
|
KERNEL_INITRAMFS := $$(KERNEL)
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | \
|
|
append-squashfs-fakeroot-be | pad-to 256 | append-rootfs | pad-rootfs | \
|
|
append-metadata | check-size
|
|
DEVICE_PACKAGES := fritz-tffs
|
|
endef
|
|
|
|
define Device/avm_fritz1750e
|
|
$(Device/avm)
|
|
SOC := qca9556
|
|
IMAGE_SIZE := 15232k
|
|
DEVICE_MODEL := FRITZ!WLAN Repeater 1750E
|
|
DEVICE_PACKAGES += rssileds kmod-ath10k-ct-smallbuffers \
|
|
ath10k-firmware-qca988x-ct -swconfig
|
|
endef
|
|
TARGET_DEVICES += avm_fritz1750e
|
|
|
|
define Device/avm_fritz300e
|
|
$(Device/avm)
|
|
SOC := ar7242
|
|
IMAGE_SIZE := 15232k
|
|
DEVICE_MODEL := FRITZ!WLAN Repeater 300E
|
|
DEVICE_PACKAGES += rssileds -swconfig
|
|
SUPPORTED_DEVICES += fritz300e
|
|
endef
|
|
TARGET_DEVICES += avm_fritz300e
|
|
|
|
define Device/avm_fritz4020
|
|
$(Device/avm)
|
|
SOC := qca9561
|
|
IMAGE_SIZE := 15232k
|
|
DEVICE_MODEL := FRITZ!Box 4020
|
|
SUPPORTED_DEVICES += fritz4020
|
|
endef
|
|
TARGET_DEVICES += avm_fritz4020
|
|
|
|
define Device/avm_fritz450e
|
|
$(Device/avm)
|
|
SOC := qca9556
|
|
IMAGE_SIZE := 15232k
|
|
DEVICE_MODEL := FRITZ!WLAN Repeater 450E
|
|
SUPPORTED_DEVICES += fritz450e
|
|
endef
|
|
TARGET_DEVICES += avm_fritz450e
|
|
|
|
define Device/avm_fritzdvbc
|
|
$(Device/avm)
|
|
SOC := qca9556
|
|
IMAGE_SIZE := 15232k
|
|
DEVICE_MODEL := FRITZ!WLAN Repeater DVB-C
|
|
DEVICE_PACKAGES += rssileds kmod-ath10k-ct-smallbuffers \
|
|
ath10k-firmware-qca988x-ct -swconfig
|
|
endef
|
|
TARGET_DEVICES += avm_fritzdvbc
|
|
|
|
define Device/belkin_f9x-v2
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Belkin
|
|
IMAGE_SIZE := 14464k
|
|
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2 \
|
|
kmod-usb3 kmod-usb-ledtrig-usbport
|
|
LOADER_TYPE := bin
|
|
LOADER_FLASH_OFFS := 0x50000
|
|
COMPILE := loader-$(1).bin loader-$(1).uImage
|
|
COMPILE/loader-$(1).bin := loader-okli-compile
|
|
COMPILE/loader-$(1).uImage := append-loader-okli $(1) | pad-to 64k | \
|
|
lzma | uImage lzma
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
edimax-headers $$$$(EDIMAX_HEADER_MAGIC) $$$$(EDIMAX_HEADER_MODEL) | \
|
|
pad-to $$$$(BLOCKSIZE)
|
|
endef
|
|
|
|
define Device/belkin_f9j1108-v2
|
|
$(Device/belkin_f9x-v2)
|
|
DEVICE_MODEL := F9J1108 v2 (AC1750 DB Wi-Fi)
|
|
EDIMAX_HEADER_MAGIC := F9J1108v1
|
|
EDIMAX_HEADER_MODEL := BR-6679BAC
|
|
endef
|
|
TARGET_DEVICES += belkin_f9j1108-v2
|
|
|
|
define Device/belkin_f9k1115-v2
|
|
$(Device/belkin_f9x-v2)
|
|
DEVICE_MODEL := F9K1115 v2 (AC1750 DB Wi-Fi)
|
|
EDIMAX_HEADER_MAGIC := eDiMaX
|
|
EDIMAX_HEADER_MODEL := F9K1115V2
|
|
endef
|
|
TARGET_DEVICES += belkin_f9k1115-v2
|
|
|
|
define Device/buffalo_bhr-4grv
|
|
$(Device/buffalo_common)
|
|
SOC := ar7242
|
|
DEVICE_MODEL := BHR-4GRV
|
|
BUFFALO_PRODUCT := BHR-4GRV
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
|
|
IMAGE_SIZE := 32256k
|
|
SUPPORTED_DEVICES += wzr-hp-g450h
|
|
endef
|
|
TARGET_DEVICES += buffalo_bhr-4grv
|
|
|
|
define Device/buffalo_bhr-4grv2
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := Buffalo
|
|
DEVICE_MODEL := BHR-4GRV2
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
TARGET_DEVICES += buffalo_bhr-4grv2
|
|
|
|
define Device/buffalo_wzr_ar7161
|
|
$(Device/buffalo_common)
|
|
SOC := ar7161
|
|
BUFFALO_PRODUCT := WZR-HP-AG300H
|
|
DEVICE_PACKAGES := kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport \
|
|
kmod-leds-reset kmod-owl-loader
|
|
IMAGE_SIZE := 32320k
|
|
SUPPORTED_DEVICES += wzr-hp-ag300h
|
|
endef
|
|
|
|
define Device/buffalo_wzr-600dhp
|
|
$(Device/buffalo_wzr_ar7161)
|
|
DEVICE_MODEL := WZR-600DHP
|
|
endef
|
|
TARGET_DEVICES += buffalo_wzr-600dhp
|
|
|
|
define Device/buffalo_wzr-hp-ag300h
|
|
$(Device/buffalo_wzr_ar7161)
|
|
DEVICE_MODEL := WZR-HP-AG300H
|
|
endef
|
|
TARGET_DEVICES += buffalo_wzr-hp-ag300h
|
|
|
|
define Device/buffalo_wzr-hp-g300nh
|
|
$(Device/buffalo_common)
|
|
SOC := ar9132
|
|
BUFFALO_PRODUCT := WZR-HP-G300NH
|
|
BUFFALO_HWVER := 1
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-gpio-nxp-74hc153
|
|
BLOCKSIZE := 128k
|
|
IMAGE_SIZE := 32128k
|
|
SUPPORTED_DEVICES += wzr-hp-g300nh
|
|
endef
|
|
|
|
define Device/buffalo_wzr-hp-g300nh-rb
|
|
$(Device/buffalo_wzr-hp-g300nh)
|
|
DEVICE_MODEL := WZR-HP-G300NH (RTL8366RB switch)
|
|
endef
|
|
TARGET_DEVICES += buffalo_wzr-hp-g300nh-rb
|
|
|
|
define Device/buffalo_wzr-hp-g300nh-s
|
|
$(Device/buffalo_wzr-hp-g300nh)
|
|
DEVICE_MODEL := WZR-HP-G300NH (RTL8366S switch)
|
|
endef
|
|
TARGET_DEVICES += buffalo_wzr-hp-g300nh-s
|
|
|
|
define Device/buffalo_wzr-hp-g302h-a1a0
|
|
$(Device/buffalo_common)
|
|
SOC := ar7242
|
|
DEVICE_MODEL := WZR-HP-G302H
|
|
DEVICE_VARIANT := A1A0
|
|
BUFFALO_PRODUCT := WZR-HP-G302H
|
|
BUFFALO_HWVER := 4
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
|
|
IMAGE_SIZE := 32128k
|
|
SUPPORTED_DEVICES += wzr-hp-g300nh2
|
|
endef
|
|
TARGET_DEVICES += buffalo_wzr-hp-g302h-a1a0
|
|
|
|
define Device/buffalo_wzr-hp-g450h
|
|
$(Device/buffalo_common)
|
|
SOC := ar7242
|
|
DEVICE_MODEL := WZR-HP-G450H/WZR-450HP
|
|
BUFFALO_PRODUCT := WZR-HP-G450H
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
|
|
IMAGE_SIZE := 32256k
|
|
SUPPORTED_DEVICES += wzr-hp-g450h
|
|
endef
|
|
TARGET_DEVICES += buffalo_wzr-hp-g450h
|
|
|
|
define Device/comfast_cf-e110n-v2
|
|
SOC := qca9533
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-E110N
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES := rssileds -swconfig -uboot-envtools
|
|
IMAGE_SIZE := 16192k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-e110n-v2
|
|
|
|
define Device/comfast_cf-e120a-v3
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-E120A
|
|
DEVICE_VARIANT := v3
|
|
DEVICE_PACKAGES := rssileds -uboot-envtools
|
|
IMAGE_SIZE := 8000k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-e120a-v3
|
|
|
|
define Device/comfast_cf-e130n-v2
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-E130N
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES := rssileds -swconfig -uboot-envtools
|
|
IMAGE_SIZE := 7936k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-e130n-v2
|
|
|
|
define Device/comfast_cf-e313ac
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-E313AC
|
|
DEVICE_PACKAGES := rssileds kmod-ath10k-ct-smallbuffers \
|
|
ath10k-firmware-qca9888-ct -swconfig -uboot-envtools
|
|
IMAGE_SIZE := 7936k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-e313ac
|
|
|
|
define Device/comfast_cf-e314n-v2
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-E314N
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES := rssileds
|
|
IMAGE_SIZE := 7936k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-e314n-v2
|
|
|
|
define Device/comfast_cf-e375ac
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-E375AC
|
|
DEVICE_PACKAGES := kmod-ath10k-ct \
|
|
ath10k-firmware-qca9888-ct -uboot-envtools
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-e375ac
|
|
|
|
define Device/comfast_cf-e5
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-E5/E7
|
|
DEVICE_PACKAGES := rssileds kmod-usb2 kmod-usb-net-qmi-wwan -swconfig \
|
|
-uboot-envtools
|
|
IMAGE_SIZE := 16192k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-e5
|
|
|
|
define Device/comfast_cf-e560ac
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-E560AC
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
|
IMAGE_SIZE := 16128k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-e560ac
|
|
|
|
define Device/comfast_cf-ew72
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-EW72
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct \
|
|
-uboot-envtools -swconfig
|
|
IMAGE_SIZE := 16192k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-ew72
|
|
|
|
define Device/comfast_cf-wr650ac-v1
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-WR650AC
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 16128k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-wr650ac-v1
|
|
|
|
define Device/comfast_cf-wr650ac-v2
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-WR650AC
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-wr650ac-v2
|
|
|
|
define Device/comfast_cf-wr752ac-v1
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := COMFAST
|
|
DEVICE_MODEL := CF-WR752AC
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct \
|
|
-uboot-envtools
|
|
IMAGE_SIZE := 16192k
|
|
endef
|
|
TARGET_DEVICES += comfast_cf-wr752ac-v1
|
|
|
|
define Device/compex_wpj344-16m
|
|
SOC := ar9344
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
IMAGE_SIZE := 16128k
|
|
DEVICE_VENDOR := Compex
|
|
DEVICE_MODEL := WPJ344
|
|
DEVICE_VARIANT := 16M
|
|
SUPPORTED_DEVICES += wpj344
|
|
IMAGES += cpximg-6a08.bin
|
|
IMAGE/cpximg-6a08.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x690 3
|
|
endef
|
|
TARGET_DEVICES += compex_wpj344-16m
|
|
|
|
define Device/compex_wpj531-16m
|
|
SOC := qca9531
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
IMAGE_SIZE := 16128k
|
|
DEVICE_VENDOR := Compex
|
|
DEVICE_MODEL := WPJ531
|
|
DEVICE_VARIANT := 16M
|
|
SUPPORTED_DEVICES += wpj531
|
|
IMAGES += cpximg-7a03.bin cpximg-7a04.bin cpximg-7a06.bin cpximg-7a07.bin
|
|
IMAGE/cpximg-7a03.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x68a 2
|
|
IMAGE/cpximg-7a04.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x693 3
|
|
IMAGE/cpximg-7a06.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x693 3
|
|
IMAGE/cpximg-7a07.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x693 3
|
|
endef
|
|
TARGET_DEVICES += compex_wpj531-16m
|
|
|
|
define Device/compex_wpj563
|
|
SOC := qca9563
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb3
|
|
IMAGE_SIZE := 16128k
|
|
DEVICE_VENDOR := Compex
|
|
DEVICE_MODEL := WPJ563
|
|
SUPPORTED_DEVICES += wpj563
|
|
IMAGES += cpximg-7a02.bin
|
|
IMAGE/cpximg-7a02.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x694 2
|
|
endef
|
|
TARGET_DEVICES += compex_wpj563
|
|
|
|
define Device/devolo_dlan-pro-1200plus-ac
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Devolo
|
|
DEVICE_MODEL := dLAN pro 1200+ WiFi ac
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15872k
|
|
endef
|
|
TARGET_DEVICES += devolo_dlan-pro-1200plus-ac
|
|
|
|
define Device/devolo_dvl1200e
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := devolo
|
|
DEVICE_MODEL := WiFi pro 1200e
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += devolo_dvl1200e
|
|
|
|
define Device/devolo_dvl1200i
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := devolo
|
|
DEVICE_MODEL := WiFi pro 1200i
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += devolo_dvl1200i
|
|
|
|
define Device/devolo_dvl1750c
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := devolo
|
|
DEVICE_MODEL := WiFi pro 1750c
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += devolo_dvl1750c
|
|
|
|
define Device/devolo_dvl1750e
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := devolo
|
|
DEVICE_MODEL := WiFi pro 1750e
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += devolo_dvl1750e
|
|
|
|
define Device/devolo_dvl1750i
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := devolo
|
|
DEVICE_MODEL := WiFi pro 1750i
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += devolo_dvl1750i
|
|
|
|
define Device/devolo_dvl1750x
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := devolo
|
|
DEVICE_MODEL := WiFi pro 1750x
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += devolo_dvl1750x
|
|
|
|
define Device/devolo_magic-2-wifi
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Devolo
|
|
DEVICE_MODEL := Magic 2 WiFi
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15872k
|
|
endef
|
|
TARGET_DEVICES += devolo_magic-2-wifi
|
|
|
|
define Device/dlink_dap-13xx
|
|
SOC := qca9533
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_PACKAGES += rssileds
|
|
IMAGE_SIZE := 7936k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | mkdapimg2 0xE0000
|
|
endef
|
|
|
|
define Device/dlink_dap-1330-a1
|
|
$(Device/dlink_dap-13xx)
|
|
DEVICE_MODEL := DAP-1330
|
|
DEVICE_VARIANT := A1
|
|
DAP_SIGNATURE := HONEYBEE-FIRMWARE-DAP-1330
|
|
SUPPORTED_DEVICES += dap-1330-a1
|
|
endef
|
|
TARGET_DEVICES += dlink_dap-1330-a1
|
|
|
|
define Device/dlink_dap-1365-a1
|
|
$(Device/dlink_dap-13xx)
|
|
DEVICE_MODEL := DAP-1365
|
|
DEVICE_VARIANT := A1
|
|
DAP_SIGNATURE := HONEYBEE-FIRMWARE-DAP-1365
|
|
endef
|
|
TARGET_DEVICES += dlink_dap-1365-a1
|
|
|
|
define Device/dlink_dap-2xxx
|
|
IMAGES += factory.img
|
|
IMAGE/factory.img := append-kernel | pad-offset 6144k 160 | \
|
|
append-rootfs | wrgg-pad-rootfs | mkwrggimg | check-size
|
|
IMAGE/sysupgrade.bin := append-kernel | mkwrggimg | \
|
|
pad-to $$$$(BLOCKSIZE) | append-rootfs | append-metadata | check-size
|
|
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
|
|
KERNEL_INITRAMFS := $$(KERNEL) | mkwrggimg
|
|
endef
|
|
|
|
define Device/dlink_dap-2230-a1
|
|
$(Device/dlink_dap-2xxx)
|
|
SOC := qca9533
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DAP-2230
|
|
DEVICE_VARIANT := A1
|
|
IMAGE_SIZE := 15232k
|
|
DAP_SIGNATURE := wapn31_dkbs_dap2230
|
|
endef
|
|
TARGET_DEVICES += dlink_dap-2230-a1
|
|
|
|
define Device/dlink_dap-2660-a1
|
|
$(Device/dlink_dap-2xxx)
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DAP-2660
|
|
DEVICE_VARIANT := A1
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
|
|
IMAGE_SIZE := 15232k
|
|
DAP_SIGNATURE := wapac09_dkbs_dap2660
|
|
endef
|
|
TARGET_DEVICES += dlink_dap-2660-a1
|
|
|
|
define Device/dlink_dap-2680-a1
|
|
$(Device/dlink_dap-2xxx)
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DAP-2680
|
|
DEVICE_VARIANT := A1
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct kmod-ath10k-ct
|
|
IMAGE_SIZE := 15232k
|
|
DAP_SIGNATURE := wapac36_dkbs_dap2680
|
|
endef
|
|
TARGET_DEVICES += dlink_dap-2680-a1
|
|
|
|
define Device/dlink_dap-2695-a1
|
|
SOC := qca9558
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DAP-2965
|
|
DEVICE_VARIANT := A1
|
|
IMAGES := factory.img sysupgrade.bin
|
|
IMAGE_SIZE := 15360k
|
|
IMAGE/default := append-kernel | pad-offset 65536 160
|
|
IMAGE/factory.img := $$(IMAGE/default) | append-rootfs | wrgg-pad-rootfs | \
|
|
mkwrggimg | check-size
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | mkwrggimg | append-rootfs | \
|
|
wrgg-pad-rootfs | append-metadata | check-size
|
|
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
|
|
KERNEL_INITRAMFS := $$(KERNEL) | mkwrggimg
|
|
DAP_SIGNATURE := wapac02_dkbs_dap2695
|
|
SUPPORTED_DEVICES += dap-2695-a1
|
|
endef
|
|
TARGET_DEVICES += dlink_dap-2695-a1
|
|
|
|
define Device/dlink_dap-3320-a1
|
|
$(Device/dlink_dap-2xxx)
|
|
SOC := qca9533
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DAP-3320
|
|
DEVICE_VARIANT := A1
|
|
IMAGE_SIZE := 15296k
|
|
DAP_SIGNATURE := wapn29_dkbs_dap3320
|
|
endef
|
|
TARGET_DEVICES += dlink_dap-3320-a1
|
|
|
|
define Device/dlink_dap-3662-a1
|
|
$(Device/dlink_dap-2xxx)
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DAP-3662
|
|
DEVICE_VARIANT := A1
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
|
|
IMAGE_SIZE := 15296k
|
|
DAP_SIGNATURE := wapac11_dkbs_dap3662
|
|
endef
|
|
TARGET_DEVICES += dlink_dap-3662-a1
|
|
|
|
define Device/dlink_dch-g020-a1
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DCH-G020
|
|
DEVICE_VARIANT := A1
|
|
DEVICE_PACKAGES := kmod-gpio-pca953x kmod-i2c-gpio kmod-usb2 kmod-usb-acm
|
|
IMAGES += factory.bin
|
|
IMAGE_SIZE := 14784k
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | mkdapimg2 0x20000
|
|
DAP_SIGNATURE := HONEYBEE-FIRMWARE-DCH-G020
|
|
endef
|
|
TARGET_DEVICES += dlink_dch-g020-a1
|
|
|
|
define Device/dlink_dir-505
|
|
SOC := ar9330
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DIR-505
|
|
IMAGE_SIZE := 7680k
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
SUPPORTED_DEVICES += dir-505-a1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-505
|
|
|
|
define Device/dlink_dir-825-b1
|
|
SOC := ar7161
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DIR-825
|
|
DEVICE_VARIANT := B1
|
|
IMAGE_SIZE := 6208k
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
append-metadata | check-size
|
|
DEVICE_PACKAGES := kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport \
|
|
kmod-leds-reset kmod-owl-loader
|
|
SUPPORTED_DEVICES += dir-825-b1
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-825-b1
|
|
|
|
define Device/dlink_dir-825-c1
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DIR-825
|
|
DEVICE_VARIANT := C1
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-leds-reset \
|
|
kmod-owl-loader
|
|
SUPPORTED_DEVICES += dir-825-c1
|
|
IMAGE_SIZE := 15936k
|
|
IMAGES := factory.bin sysupgrade.bin
|
|
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
|
|
pad-rootfs
|
|
IMAGE/factory.bin := $$(IMAGE/default) | pad-offset $$$$(IMAGE_SIZE) 26 | \
|
|
append-string 00DB120AR9344-RT-101214-00 | check-size
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | \
|
|
check-size
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-825-c1
|
|
|
|
define Device/dlink_dir-835-a1
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DIR-835
|
|
DEVICE_VARIANT := A1
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-leds-reset kmod-owl-loader
|
|
SUPPORTED_DEVICES += dir-835-a1
|
|
IMAGE_SIZE := 15936k
|
|
IMAGES := factory.bin sysupgrade.bin
|
|
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
|
|
pad-rootfs
|
|
IMAGE/factory.bin := $$(IMAGE/default) | pad-offset $$$$(IMAGE_SIZE) 26 | \
|
|
append-string 00DB120AR9344-RT-101214-00 | check-size
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | \
|
|
check-size
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-835-a1
|
|
|
|
define Device/dlink_dir-842-c
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DIR-842
|
|
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
|
|
KERNEL_INITRAMFS := $$(KERNEL) | seama
|
|
IMAGES += factory.bin
|
|
SEAMA_MTDBLOCK := 5
|
|
SEAMA_SIGNATURE := wrgac65_dlink.2015_dir842
|
|
# 64 bytes offset:
|
|
# - 28 bytes seama_header
|
|
# - 36 bytes of META data (4-bytes aligned)
|
|
IMAGE/default := append-kernel | uImage lzma | \
|
|
pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | seama | pad-rootfs | \
|
|
append-metadata | check-size
|
|
IMAGE/factory.bin := $$(IMAGE/default) | pad-rootfs -x 64 | seama | \
|
|
seama-seal | check-size
|
|
IMAGE_SIZE := 15680k
|
|
endef
|
|
|
|
define Device/dlink_dir-842-c1
|
|
$(Device/dlink_dir-842-c)
|
|
DEVICE_VARIANT := C1
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-842-c1
|
|
|
|
define Device/dlink_dir-842-c2
|
|
$(Device/dlink_dir-842-c)
|
|
DEVICE_VARIANT := C2
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-842-c2
|
|
|
|
define Device/dlink_dir-842-c3
|
|
$(Device/dlink_dir-842-c)
|
|
DEVICE_VARIANT := C3
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-842-c3
|
|
|
|
define Device/dlink_dir-859-a1
|
|
$(Device/seama)
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DIR-859
|
|
DEVICE_VARIANT := A1
|
|
IMAGE_SIZE := 15872k
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
|
|
SEAMA_SIGNATURE := wrgac37_dlink.2013gui_dir859
|
|
endef
|
|
TARGET_DEVICES += dlink_dir-859-a1
|
|
|
|
define Device/elecom_wrc-1750ghbk2-i
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := ELECOM
|
|
DEVICE_MODEL := WRC-1750GHBK2-I/C
|
|
IMAGE_SIZE := 15808k
|
|
KERNEL_INITRAMFS := $$(KERNEL) | pad-to 2 | \
|
|
add-elecom-factory-initramfs RN68 WRC-1750GHBK2
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-1750ghbk2-i
|
|
|
|
define Device/elecom_wrc-300ghbk2-i
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := ELECOM
|
|
DEVICE_MODEL := WRC-300GHBK2-I
|
|
IMAGE_SIZE := 7616k
|
|
KERNEL_INITRAMFS := $$(KERNEL) | pad-to 2 | \
|
|
add-elecom-factory-initramfs RN51 WRC-300GHBK2-I
|
|
endef
|
|
TARGET_DEVICES += elecom_wrc-300ghbk2-i
|
|
|
|
define Device/embeddedwireless_dorin
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := Embedded Wireless
|
|
DEVICE_MODEL := Dorin
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
TARGET_DEVICES += embeddedwireless_dorin
|
|
|
|
define Device/engenius_eap1200h
|
|
$(Device/senao_loader_okli)
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EAP1200H
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
|
|
IMAGE_SIZE := 11584k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := ar71xx-generic-eap1200h
|
|
endef
|
|
TARGET_DEVICES += engenius_eap1200h
|
|
|
|
define Device/engenius_eap300-v2
|
|
$(Device/senao_loader_okli)
|
|
SOC := ar9341
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EAP300
|
|
DEVICE_VARIANT := v2
|
|
IMAGE_SIZE := 12096k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := senao-eap300v2
|
|
endef
|
|
TARGET_DEVICES += engenius_eap300-v2
|
|
|
|
define Device/engenius_eap600
|
|
$(Device/senao_loader_okli)
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EAP600
|
|
IMAGE_SIZE := 12096k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := senao-eap600
|
|
endef
|
|
TARGET_DEVICES += engenius_eap600
|
|
|
|
define Device/engenius_ecb1200
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := ECB1200
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
|
|
IMAGE_SIZE := 15680k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
senao-header -r 0x101 -p 0x6e -t 2
|
|
endef
|
|
TARGET_DEVICES += engenius_ecb1200
|
|
|
|
define Device/engenius_ecb1750
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := ECB1750
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
|
|
IMAGE_SIZE := 15680k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
senao-header -r 0x101 -p 0x6d -t 2
|
|
endef
|
|
TARGET_DEVICES += engenius_ecb1750
|
|
|
|
define Device/engenius_ecb600
|
|
$(Device/senao_loader_okli)
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := ECB600
|
|
IMAGE_SIZE := 12096k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := senao-ecb600
|
|
endef
|
|
TARGET_DEVICES += engenius_ecb600
|
|
|
|
define Device/engenius_ens202ext-v1
|
|
$(Device/senao_loader_okli)
|
|
SOC := ar9341
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := ENS202EXT
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := rssileds
|
|
IMAGE_SIZE := 12096k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := senao-ens202ext
|
|
endef
|
|
TARGET_DEVICES += engenius_ens202ext-v1
|
|
|
|
define Device/engenius_enstationac-v1
|
|
$(Device/senao_loader_okli)
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EnStationAC
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct rssileds
|
|
IMAGE_SIZE := 11584k
|
|
LOADER_FLASH_OFFS := 0x220000
|
|
SENAO_IMGNAME := ar71xx-generic-enstationac
|
|
endef
|
|
TARGET_DEVICES += engenius_enstationac-v1
|
|
|
|
define Device/engenius_epg5000
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EPG5000
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2
|
|
IMAGE_SIZE := 14656k
|
|
IMAGES += factory.dlf
|
|
IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
senao-header -r 0x101 -p 0x71 -t 2
|
|
SUPPORTED_DEVICES += epg5000
|
|
endef
|
|
TARGET_DEVICES += engenius_epg5000
|
|
|
|
define Device/engenius_ews511ap
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EWS511AP
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
TARGET_DEVICES += engenius_ews511ap
|
|
|
|
define Device/enterasys_ws-ap3705i
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Enterasys
|
|
DEVICE_MODEL := WS-AP3705i
|
|
IMAGE_SIZE := 30528k
|
|
endef
|
|
TARGET_DEVICES += enterasys_ws-ap3705i
|
|
|
|
define Device/etactica_eg200
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := eTactica
|
|
DEVICE_MODEL := EG200
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-ledtrig-oneshot \
|
|
kmod-usb-serial-ftdi kmod-usb-storage kmod-fs-ext4
|
|
IMAGE_SIZE := 16000k
|
|
SUPPORTED_DEVICES += rme-eg200
|
|
endef
|
|
TARGET_DEVICES += etactica_eg200
|
|
|
|
define Device/glinet_6408
|
|
$(Device/tplink-8mlzma)
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := 6408
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
IMAGE_SIZE := 8000k
|
|
TPLINK_HWID := 0x08000001
|
|
IMAGES := sysupgrade.bin
|
|
SUPPORTED_DEVICES += gl-inet
|
|
endef
|
|
TARGET_DEVICES += glinet_6408
|
|
|
|
define Device/glinet_6416
|
|
$(Device/tplink-16mlzma)
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := 6416
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
IMAGE_SIZE := 16192k
|
|
TPLINK_HWID := 0x08000001
|
|
IMAGES := sysupgrade.bin
|
|
SUPPORTED_DEVICES += gl-inet
|
|
endef
|
|
TARGET_DEVICES += glinet_6416
|
|
|
|
define Device/glinet_gl-ar150
|
|
SOC := ar9330
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-AR150
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2
|
|
IMAGE_SIZE := 16000k
|
|
SUPPORTED_DEVICES += gl-ar150
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-ar150
|
|
|
|
define Device/glinet_gl-ar300m-common-nor
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
IMAGE_SIZE := 16000k
|
|
SUPPORTED_DEVICES += gl-ar300m
|
|
endef
|
|
|
|
define Device/glinet_gl-ar300m-lite
|
|
$(Device/glinet_gl-ar300m-common-nor)
|
|
DEVICE_MODEL := GL-AR300M
|
|
DEVICE_VARIANT := Lite
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-ar300m-lite
|
|
|
|
define Device/glinet_gl-ar300m16
|
|
$(Device/glinet_gl-ar300m-common-nor)
|
|
DEVICE_MODEL := GL-AR300M16
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-ar300m16
|
|
|
|
define Device/glinet_gl-ar750
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-AR750
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9887-ct
|
|
IMAGE_SIZE := 16000k
|
|
SUPPORTED_DEVICES += gl-ar750
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-ar750
|
|
|
|
define Device/glinet_gl-mifi
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := GL.iNET
|
|
DEVICE_MODEL := GL-MiFi
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2
|
|
IMAGE_SIZE := 16000k
|
|
SUPPORTED_DEVICES += gl-mifi
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-mifi
|
|
|
|
define Device/glinet_gl-usb150
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := GL.iNET
|
|
DEVICE_MODEL := GL-USB150
|
|
IMAGE_SIZE := 16000k
|
|
SUPPORTED_DEVICES += gl-usb150
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-usb150
|
|
|
|
define Device/glinet_gl-x750
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-X750
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9887-ct
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-x750
|
|
|
|
define Device/hak5_lan-turtle
|
|
$(Device/tplink-16mlzma)
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := Hak5
|
|
DEVICE_MODEL := LAN Turtle
|
|
TPLINK_HWID := 0x5348334c
|
|
IMAGES := sysupgrade.bin
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2 -iwinfo -kmod-ath9k -swconfig \
|
|
-uboot-envtools -wpad-basic-wolfssl
|
|
SUPPORTED_DEVICES += lan-turtle
|
|
endef
|
|
TARGET_DEVICES += hak5_lan-turtle
|
|
|
|
define Device/hak5_packet-squirrel
|
|
$(Device/tplink-16mlzma)
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := Hak5
|
|
DEVICE_MODEL := Packet Squirrel
|
|
TPLINK_HWID := 0x5351524c
|
|
IMAGES := sysupgrade.bin
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2 -iwinfo -kmod-ath9k -swconfig \
|
|
-uboot-envtools -wpad-basic-wolfssl
|
|
SUPPORTED_DEVICES += packet-squirrel
|
|
endef
|
|
TARGET_DEVICES += hak5_packet-squirrel
|
|
|
|
define Device/hak5_wifi-pineapple-nano
|
|
$(Device/tplink-16mlzma)
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := Hak5
|
|
DEVICE_MODEL := WiFi Pineapple NANO
|
|
TPLINK_HWID := 0x4e414e4f
|
|
IMAGES := sysupgrade.bin
|
|
DEVICE_PACKAGES := kmod-ath9k-htc kmod-usb-chipidea2 kmod-usb-storage \
|
|
-swconfig -uboot-envtools
|
|
SUPPORTED_DEVICES += wifi-pineapple-nano
|
|
endef
|
|
TARGET_DEVICES += hak5_wifi-pineapple-nano
|
|
|
|
define Device/iodata_etg3-r
|
|
SOC := ar9342
|
|
DEVICE_VENDOR := I-O DATA
|
|
DEVICE_MODEL := ETG3-R
|
|
IMAGE_SIZE := 7680k
|
|
DEVICE_PACKAGES := -iwinfo -kmod-ath9k -wpad-basic-wolfssl
|
|
endef
|
|
TARGET_DEVICES += iodata_etg3-r
|
|
|
|
define Device/iodata_wn-ac1167dgr
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := I-O DATA
|
|
DEVICE_MODEL := WN-AC1167DGR
|
|
IMAGE_SIZE := 14656k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
senao-header -r 0x30a -p 0x61 -t 2
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-ac1167dgr
|
|
|
|
define Device/iodata_wn-ac1600dgr
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := I-O DATA
|
|
DEVICE_MODEL := WN-AC1600DGR
|
|
IMAGE_SIZE := 14656k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
senao-header -r 0x30a -p 0x60 -t 2 -v 200
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-ac1600dgr
|
|
|
|
define Device/iodata_wn-ac1600dgr2
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := I-O DATA
|
|
DEVICE_MODEL := WN-AC1600DGR2/DGR3
|
|
IMAGE_SIZE := 14656k
|
|
IMAGES += dgr2-dgr3-factory.bin
|
|
IMAGE/dgr2-dgr3-factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
senao-header -r 0x30a -p 0x60 -t 2 -v 200
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-ac1600dgr2
|
|
|
|
define Device/iodata_wn-ag300dgr
|
|
SOC := ar1022
|
|
DEVICE_VENDOR := I-O DATA
|
|
DEVICE_MODEL := WN-AG300DGR
|
|
IMAGE_SIZE := 15424k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
senao-header -r 0x30a -p 0x47 -t 2
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
endef
|
|
TARGET_DEVICES += iodata_wn-ag300dgr
|
|
|
|
define Device/jjplus_ja76pf2
|
|
SOC := ar7161
|
|
DEVICE_VENDOR := jjPlus
|
|
DEVICE_MODEL := JA76PF2
|
|
DEVICE_PACKAGES += -kmod-ath9k -swconfig -wpad-basic-wolfssl -uboot-envtools fconfig
|
|
IMAGES += kernel.bin rootfs.bin
|
|
IMAGE/kernel.bin := append-kernel
|
|
IMAGE/rootfs.bin := append-rootfs | pad-rootfs
|
|
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | combined-image | \
|
|
append-metadata | check-size
|
|
KERNEL := kernel-bin | append-dtb | lzma | pad-to $$(BLOCKSIZE)
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb
|
|
IMAGE_SIZE := 16000k
|
|
SUPPORTED_DEVICES += ja76pf2
|
|
endef
|
|
TARGET_DEVICES += jjplus_ja76pf2
|
|
|
|
define Device/librerouter_librerouter-v1
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Librerouter
|
|
DEVICE_MODEL := LibreRouter
|
|
DEVICE_VARIANT := v1
|
|
IMAGE_SIZE := 7936k
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
endef
|
|
TARGET_DEVICES += librerouter_librerouter-v1
|
|
|
|
define Device/meraki_mr12
|
|
SOC := ar7242
|
|
DEVICE_VENDOR := Meraki
|
|
DEVICE_MODEL := MR12
|
|
IMAGE_SIZE := 15616k
|
|
DEVICE_PACKAGES := kmod-owl-loader rssileds
|
|
SUPPORTED_DEVICES += mr12
|
|
DEVICE_COMPAT_VERSION := 2.0
|
|
DEVICE_COMPAT_MESSAGE := Partitions differ from ar71xx version of MR12. Image format is incompatible. \
|
|
To use sysupgrade, you must change /lib/update/common.sh::get_image to prepend 128K zeroes to this image, \
|
|
and change the bootcmd in u-boot to "bootm 0xbf0a0000". After that, you can use "sysupgrade -F -n". \
|
|
Make sure you do not keep your old config, as ethernet setup is not compatible either. \
|
|
For more details, see the OpenWrt Wiki: https://openwrt.org/toh/meraki/MR12, \
|
|
or the commit message of the MR12 ath79 port on git.openwrt.org.
|
|
endef
|
|
TARGET_DEVICES += meraki_mr12
|
|
|
|
define Device/meraki_mr16
|
|
SOC := ar7161
|
|
DEVICE_VENDOR := Meraki
|
|
DEVICE_MODEL := MR16
|
|
IMAGE_SIZE := 15616k
|
|
DEVICE_PACKAGES := kmod-owl-loader
|
|
SUPPORTED_DEVICES += mr16
|
|
DEVICE_COMPAT_VERSION := 2.0
|
|
DEVICE_COMPAT_MESSAGE := Partitions differ from ar71xx version of MR16. Image format is incompatible. \
|
|
To use sysupgrade, you must change /lib/update/common.sh::get_image to prepend 128K zeroes to this image, \
|
|
and change the bootcmd in u-boot to "bootm 0xbf0a0000". After that, you can use "sysupgrade -F". \
|
|
For more details, see the OpenWrt Wiki: https://openwrt.org/toh/meraki/mr16, \
|
|
or the commit message of the MR16 ath79 port on git.openwrt.org.
|
|
endef
|
|
TARGET_DEVICES += meraki_mr16
|
|
|
|
define Device/mercury_mw4530r-v1
|
|
$(Device/tplink-8mlzma)
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Mercury
|
|
DEVICE_MODEL := MW4530R
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
|
|
TPLINK_HWID := 0x45300001
|
|
SUPPORTED_DEVICES += tl-wdr4300
|
|
endef
|
|
TARGET_DEVICES += mercury_mw4530r-v1
|
|
|
|
define Device/nec_wx1200cr
|
|
DEVICE_VENDOR := NEC
|
|
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | seama | pad-rootfs | \
|
|
append-metadata | check-size
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
|
endef
|
|
|
|
define Device/nec_wf1200cr
|
|
$(Device/nec_wx1200cr)
|
|
SOC := qca9561
|
|
DEVICE_MODEL := Aterm WF1200CR
|
|
IMAGE_SIZE := 7680k
|
|
SEAMA_MTDBLOCK := 5
|
|
SEAMA_SIGNATURE := wrgac62_necpf.2016gui_wf1200cr
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(IMAGE/default) | pad-rootfs -x 64 | seama | \
|
|
seama-seal | nec-enc ryztfyutcrqqo69d | check-size
|
|
endef
|
|
TARGET_DEVICES += nec_wf1200cr
|
|
|
|
define Device/nec_wg1200cr
|
|
$(Device/nec_wx1200cr)
|
|
SOC := qca9563
|
|
DEVICE_MODEL := Aterm WG1200CR
|
|
IMAGE_SIZE := 7616k
|
|
SEAMA_MTDBLOCK := 6
|
|
SEAMA_SIGNATURE := wrgac72_necpf.2016gui_wg1200cr
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(IMAGE/default) | pad-rootfs -x 64 | seama | \
|
|
seama-seal | nec-enc 9gsiy9nzep452pad | check-size
|
|
endef
|
|
TARGET_DEVICES += nec_wg1200cr
|
|
|
|
define Device/nec_wg800hp
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := NEC
|
|
DEVICE_MODEL := Aterm WG800HP
|
|
IMAGE_SIZE := 7104k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
xor-image -p 6A57190601121E4C004C1E1201061957 -x | nec-fw LASER_ATERM
|
|
DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers ath10k-firmware-qca9887-ct-full-htt
|
|
endef
|
|
TARGET_DEVICES += nec_wg800hp
|
|
|
|
define Device/netgear_ex6400_ex7300
|
|
$(Device/netgear_generic)
|
|
SOC := qca9558
|
|
UIMAGE_MAGIC := 0x27051956
|
|
NETGEAR_BOARD_ID := EX7300series
|
|
NETGEAR_HW_ID := 29765104+16+0+128
|
|
IMAGE_SIZE := 15552k
|
|
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | \
|
|
netgear-rootfs | pad-rootfs
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | \
|
|
check-size
|
|
IMAGE/factory.img := $$(IMAGE/default) | netgear-dni | \
|
|
check-size
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca99x0-ct
|
|
endef
|
|
|
|
define Device/netgear_ex6400
|
|
$(Device/netgear_ex6400_ex7300)
|
|
DEVICE_MODEL := EX6400
|
|
endef
|
|
TARGET_DEVICES += netgear_ex6400
|
|
|
|
define Device/netgear_ex7300
|
|
$(Device/netgear_ex6400_ex7300)
|
|
DEVICE_MODEL := EX7300
|
|
endef
|
|
TARGET_DEVICES += netgear_ex7300
|
|
|
|
define Device/netgear_wndr3x00
|
|
$(Device/netgear_generic)
|
|
SOC := ar7161
|
|
DEVICE_PACKAGES := kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport \
|
|
kmod-leds-reset kmod-owl-loader
|
|
endef
|
|
|
|
define Device/netgear_wndr3700
|
|
$(Device/netgear_wndr3x00)
|
|
DEVICE_MODEL := WNDR3700
|
|
DEVICE_VARIANT := v1
|
|
UIMAGE_MAGIC := 0x33373030
|
|
NETGEAR_BOARD_ID := WNDR3700
|
|
IMAGE_SIZE := 7680k
|
|
IMAGES += factory-NA.img
|
|
IMAGE/factory-NA.img := $$(IMAGE/default) | netgear-dni NA | \
|
|
check-size
|
|
SUPPORTED_DEVICES += wndr3700
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr3700
|
|
|
|
define Device/netgear_wndr3700-v2
|
|
$(Device/netgear_wndr3x00)
|
|
DEVICE_MODEL := WNDR3700
|
|
DEVICE_VARIANT := v2
|
|
UIMAGE_MAGIC := 0x33373031
|
|
NETGEAR_BOARD_ID := WNDR3700v2
|
|
NETGEAR_HW_ID := 29763654+16+64
|
|
IMAGE_SIZE := 15872k
|
|
SUPPORTED_DEVICES += wndr3700 netgear,wndr3700v2
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr3700-v2
|
|
|
|
define Device/netgear_wndr3800
|
|
$(Device/netgear_wndr3x00)
|
|
DEVICE_MODEL := WNDR3800
|
|
UIMAGE_MAGIC := 0x33373031
|
|
NETGEAR_BOARD_ID := WNDR3800
|
|
NETGEAR_HW_ID := 29763654+16+128
|
|
IMAGE_SIZE := 15872k
|
|
SUPPORTED_DEVICES += wndr3700
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr3800
|
|
|
|
define Device/netgear_wndr3800ch
|
|
$(Device/netgear_wndr3x00)
|
|
DEVICE_MODEL := WNDR3800CH
|
|
UIMAGE_MAGIC := 0x33373031
|
|
NETGEAR_BOARD_ID := WNDR3800CH
|
|
NETGEAR_HW_ID := 29763654+16+128
|
|
IMAGE_SIZE := 15872k
|
|
SUPPORTED_DEVICES += wndr3700
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr3800ch
|
|
|
|
define Device/netgear_wndrmac-v1
|
|
$(Device/netgear_wndr3x00)
|
|
DEVICE_MODEL := WNDRMAC
|
|
DEVICE_VARIANT := v1
|
|
UIMAGE_MAGIC := 0x33373031
|
|
NETGEAR_BOARD_ID := WNDRMAC
|
|
NETGEAR_HW_ID := 29763654+16+64
|
|
IMAGE_SIZE := 15872k
|
|
SUPPORTED_DEVICES += wndr3700
|
|
endef
|
|
TARGET_DEVICES += netgear_wndrmac-v1
|
|
|
|
define Device/netgear_wndrmac-v2
|
|
$(Device/netgear_wndr3x00)
|
|
DEVICE_MODEL := WNDRMAC
|
|
DEVICE_VARIANT := v2
|
|
UIMAGE_MAGIC := 0x33373031
|
|
NETGEAR_BOARD_ID := WNDRMACv2
|
|
NETGEAR_HW_ID := 29763654+16+128
|
|
IMAGE_SIZE := 15872k
|
|
SUPPORTED_DEVICES += wndr3700
|
|
endef
|
|
TARGET_DEVICES += netgear_wndrmac-v2
|
|
|
|
define Device/netgear_wnr2200_common
|
|
$(Device/netgear_generic)
|
|
SOC := ar7241
|
|
DEVICE_MODEL := WNR2200
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
|
|
UIMAGE_MAGIC := 0x32323030
|
|
NETGEAR_BOARD_ID := wnr2200
|
|
endef
|
|
|
|
define Device/netgear_wnr2200-8m
|
|
$(Device/netgear_wnr2200_common)
|
|
DEVICE_VARIANT := 8M
|
|
NETGEAR_HW_ID := 29763600+08+64
|
|
IMAGE_SIZE := 7808k
|
|
IMAGES += factory-NA.img
|
|
IMAGE/factory-NA.img := $$(IMAGE/default) | netgear-dni NA | \
|
|
check-size
|
|
SUPPORTED_DEVICES += wnr2200
|
|
endef
|
|
TARGET_DEVICES += netgear_wnr2200-8m
|
|
|
|
define Device/netgear_wnr2200-16m
|
|
$(Device/netgear_wnr2200_common)
|
|
DEVICE_VARIANT := 16M
|
|
DEVICE_ALT0_VENDOR := NETGEAR
|
|
DEVICE_ALT0_MODEL := WNR2200
|
|
DEVICE_ALT0_VARIANT := CN/RU
|
|
NETGEAR_HW_ID :=
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
TARGET_DEVICES += netgear_wnr2200-16m
|
|
|
|
define Device/ocedo_koala
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Ocedo
|
|
DEVICE_MODEL := Koala
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
SUPPORTED_DEVICES += koala
|
|
IMAGE_SIZE := 7424k
|
|
endef
|
|
TARGET_DEVICES += ocedo_koala
|
|
|
|
define Device/ocedo_raccoon
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Ocedo
|
|
DEVICE_MODEL := Raccoon
|
|
IMAGE_SIZE := 7424k
|
|
endef
|
|
TARGET_DEVICES += ocedo_raccoon
|
|
|
|
define Device/ocedo_ursus
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Ocedo
|
|
DEVICE_MODEL := Ursus
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 7424k
|
|
endef
|
|
TARGET_DEVICES += ocedo_ursus
|
|
|
|
define Device/openmesh_common_64k
|
|
DEVICE_VENDOR := OpenMesh
|
|
DEVICE_PACKAGES := uboot-envtools
|
|
IMAGE_SIZE := 7808k
|
|
BLOCKSIZE := 64k
|
|
OPENMESH_CE_TYPE :=
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma | \
|
|
pad-to $$(BLOCKSIZE)
|
|
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | \
|
|
openmesh-image ce_type=$$$$(OPENMESH_CE_TYPE) | append-metadata
|
|
endef
|
|
|
|
define Device/openmesh_common_256k
|
|
DEVICE_VENDOR := OpenMesh
|
|
DEVICE_PACKAGES := uboot-envtools
|
|
IMAGE_SIZE := 7168k
|
|
BLOCKSIZE := 256k
|
|
OPENMESH_CE_TYPE :=
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma | \
|
|
pad-to $$(BLOCKSIZE)
|
|
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | \
|
|
openmesh-image ce_type=$$$$(OPENMESH_CE_TYPE) | append-metadata
|
|
endef
|
|
|
|
define Device/openmesh_a40
|
|
$(Device/openmesh_common_64k)
|
|
SOC := qca9558
|
|
DEVICE_MODEL := A40
|
|
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2
|
|
OPENMESH_CE_TYPE := A60
|
|
SUPPORTED_DEVICES += a40
|
|
endef
|
|
TARGET_DEVICES += openmesh_a40
|
|
|
|
define Device/openmesh_a60
|
|
$(Device/openmesh_common_64k)
|
|
SOC := qca9558
|
|
DEVICE_MODEL := A60
|
|
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2
|
|
OPENMESH_CE_TYPE := A60
|
|
SUPPORTED_DEVICES += a60
|
|
endef
|
|
TARGET_DEVICES += openmesh_a60
|
|
|
|
define Device/openmesh_mr600-v1
|
|
$(Device/openmesh_common_64k)
|
|
SOC := ar9344
|
|
DEVICE_MODEL := MR600
|
|
DEVICE_VARIANT := v1
|
|
OPENMESH_CE_TYPE := MR600
|
|
SUPPORTED_DEVICES += mr600
|
|
endef
|
|
TARGET_DEVICES += openmesh_mr600-v1
|
|
|
|
define Device/openmesh_mr600-v2
|
|
$(Device/openmesh_common_64k)
|
|
SOC := ar9344
|
|
DEVICE_MODEL := MR600
|
|
DEVICE_VARIANT := v2
|
|
OPENMESH_CE_TYPE := MR600
|
|
SUPPORTED_DEVICES += mr600v2
|
|
endef
|
|
TARGET_DEVICES += openmesh_mr600-v2
|
|
|
|
define Device/openmesh_mr900-v1
|
|
$(Device/openmesh_common_64k)
|
|
SOC := qca9558
|
|
DEVICE_MODEL := MR900
|
|
DEVICE_VARIANT := v1
|
|
OPENMESH_CE_TYPE := MR900
|
|
SUPPORTED_DEVICES += mr900
|
|
endef
|
|
TARGET_DEVICES += openmesh_mr900-v1
|
|
|
|
define Device/openmesh_mr900-v2
|
|
$(Device/openmesh_common_64k)
|
|
SOC := qca9558
|
|
DEVICE_MODEL := MR900
|
|
DEVICE_VARIANT := v2
|
|
OPENMESH_CE_TYPE := MR900
|
|
SUPPORTED_DEVICES += mr900v2
|
|
endef
|
|
TARGET_DEVICES += openmesh_mr900-v2
|
|
|
|
define Device/openmesh_mr1750-v1
|
|
$(Device/openmesh_common_64k)
|
|
SOC := qca9558
|
|
DEVICE_MODEL := MR1750
|
|
DEVICE_VARIANT := v1
|
|
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
OPENMESH_CE_TYPE := MR1750
|
|
SUPPORTED_DEVICES += mr1750
|
|
endef
|
|
TARGET_DEVICES += openmesh_mr1750-v1
|
|
|
|
define Device/openmesh_mr1750-v2
|
|
$(Device/openmesh_common_64k)
|
|
SOC := qca9558
|
|
DEVICE_MODEL := MR1750
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
OPENMESH_CE_TYPE := MR1750
|
|
SUPPORTED_DEVICES += mr1750v2
|
|
endef
|
|
TARGET_DEVICES += openmesh_mr1750-v2
|
|
|
|
define Device/openmesh_om2p-v2
|
|
$(Device/openmesh_common_256k)
|
|
SOC := ar9330
|
|
DEVICE_MODEL := OM2P
|
|
DEVICE_VARIANT := v2
|
|
OPENMESH_CE_TYPE := OM2P
|
|
SUPPORTED_DEVICES += om2pv2
|
|
endef
|
|
TARGET_DEVICES += openmesh_om2p-v2
|
|
|
|
define Device/openmesh_om2p-v4
|
|
$(Device/openmesh_common_256k)
|
|
SOC := qca9533
|
|
DEVICE_MODEL := OM2P
|
|
DEVICE_VARIANT := v4
|
|
OPENMESH_CE_TYPE := OM2P
|
|
SUPPORTED_DEVICES += om2pv4
|
|
endef
|
|
TARGET_DEVICES += openmesh_om2p-v4
|
|
|
|
define Device/openmesh_om2p-hs-v1
|
|
$(Device/openmesh_common_256k)
|
|
SOC := ar9341
|
|
DEVICE_MODEL := OM2P-HS
|
|
DEVICE_VARIANT := v1
|
|
OPENMESH_CE_TYPE := OM2P
|
|
SUPPORTED_DEVICES += om2p-hs
|
|
endef
|
|
TARGET_DEVICES += openmesh_om2p-hs-v1
|
|
|
|
define Device/openmesh_om2p-hs-v2
|
|
$(Device/openmesh_common_256k)
|
|
SOC := ar9341
|
|
DEVICE_MODEL := OM2P-HS
|
|
DEVICE_VARIANT := v2
|
|
OPENMESH_CE_TYPE := OM2P
|
|
SUPPORTED_DEVICES += om2p-hsv2
|
|
endef
|
|
TARGET_DEVICES += openmesh_om2p-hs-v2
|
|
|
|
define Device/openmesh_om2p-hs-v3
|
|
$(Device/openmesh_common_256k)
|
|
SOC := ar9341
|
|
DEVICE_MODEL := OM2P-HS
|
|
DEVICE_VARIANT := v3
|
|
OPENMESH_CE_TYPE := OM2P
|
|
SUPPORTED_DEVICES += om2p-hsv3
|
|
endef
|
|
TARGET_DEVICES += openmesh_om2p-hs-v3
|
|
|
|
define Device/openmesh_om2p-hs-v4
|
|
$(Device/openmesh_common_256k)
|
|
SOC := qca9533
|
|
DEVICE_MODEL := OM2P-HS
|
|
DEVICE_VARIANT := v4
|
|
OPENMESH_CE_TYPE := OM2P
|
|
SUPPORTED_DEVICES += om2p-hsv4
|
|
endef
|
|
TARGET_DEVICES += openmesh_om2p-hs-v4
|
|
|
|
define Device/openmesh_om2p-lc
|
|
$(Device/openmesh_common_256k)
|
|
SOC := ar9330
|
|
DEVICE_MODEL := OM2P-LC
|
|
OPENMESH_CE_TYPE := OM2P
|
|
SUPPORTED_DEVICES += om2p-lc
|
|
endef
|
|
TARGET_DEVICES += openmesh_om2p-lc
|
|
|
|
define Device/openmesh_om5p
|
|
$(Device/openmesh_common_64k)
|
|
SOC := ar9344
|
|
DEVICE_MODEL := OM5P
|
|
OPENMESH_CE_TYPE := OM5P
|
|
SUPPORTED_DEVICES += om5p
|
|
endef
|
|
TARGET_DEVICES += openmesh_om5p
|
|
|
|
define Device/openmesh_om5p-ac-v2
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := OpenMesh
|
|
DEVICE_MODEL := OM5P-AC
|
|
DEVICE_VARIANT := v2
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct om-watchdog
|
|
IMAGE_SIZE := 7808k
|
|
SUPPORTED_DEVICES += om5p-acv2
|
|
endef
|
|
TARGET_DEVICES += openmesh_om5p-ac-v2
|
|
|
|
define Device/pcs_cap324
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := PowerCloud Systems
|
|
DEVICE_MODEL := CAP324
|
|
IMAGE_SIZE := 16000k
|
|
SUPPORTED_DEVICES += cap324
|
|
endef
|
|
TARGET_DEVICES += pcs_cap324
|
|
|
|
define Device/pcs_cr3000
|
|
SOC := ar9341
|
|
DEVICE_VENDOR := PowerCloud Systems
|
|
DEVICE_MODEL := CR3000
|
|
IMAGE_SIZE := 7808k
|
|
SUPPORTED_DEVICES += cr3000
|
|
endef
|
|
TARGET_DEVICES += pcs_cr3000
|
|
|
|
define Device/pcs_cr5000
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := PowerCloud Systems
|
|
DEVICE_MODEL := CR5000
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
IMAGE_SIZE := 7808k
|
|
SUPPORTED_DEVICES += cr5000
|
|
endef
|
|
TARGET_DEVICES += pcs_cr5000
|
|
|
|
define Device/phicomm_k2t
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := Phicomm
|
|
DEVICE_MODEL := K2T
|
|
IMAGE_SIZE := 15744k
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
append-metadata | check-size
|
|
DEVICE_PACKAGES := kmod-leds-reset kmod-ath10k-ct-smallbuffers ath10k-firmware-qca9888-ct
|
|
endef
|
|
TARGET_DEVICES += phicomm_k2t
|
|
|
|
define Device/pisen_ts-d084
|
|
$(Device/tplink-8mlzma)
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := PISEN
|
|
DEVICE_MODEL := TS-D084
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2
|
|
TPLINK_HWID := 0x07030101
|
|
endef
|
|
TARGET_DEVICES += pisen_ts-d084
|
|
|
|
define Device/pisen_wmb001n
|
|
SOC := ar9341
|
|
DEVICE_VENDOR := PISEN
|
|
DEVICE_MODEL := WMB001N
|
|
IMAGE_SIZE := 14080k
|
|
DEVICE_PACKAGES := kmod-i2c-gpio kmod-usb2
|
|
LOADER_TYPE := bin
|
|
LOADER_FLASH_OFFS := 0x20000
|
|
COMPILE := loader-$(1).bin loader-$(1).uImage
|
|
COMPILE/loader-$(1).bin := loader-okli-compile
|
|
COMPILE/loader-$(1).uImage := append-loader-okli $(1) | pad-to 64k | lzma | \
|
|
uImage lzma
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := $$(IMAGE/sysupgrade.bin) | pisen_wmb001n-factory $(1)
|
|
endef
|
|
TARGET_DEVICES += pisen_wmb001n
|
|
|
|
define Device/pisen_wmm003n
|
|
$(Device/tplink-8mlzma)
|
|
SOC := ar9331
|
|
DEVICE_VENDOR := PISEN
|
|
DEVICE_MODEL := Cloud Easy Power (WMM003N)
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2
|
|
TPLINK_HWID := 0x07030101
|
|
endef
|
|
TARGET_DEVICES += pisen_wmm003n
|
|
|
|
define Device/plasmacloud_pa300-common
|
|
SOC := qca9533
|
|
DEVICE_VENDOR := Plasma Cloud
|
|
DEVICE_PACKAGES := uboot-envtools
|
|
IMAGE_SIZE := 7168k
|
|
BLOCKSIZE := 64k
|
|
IMAGES += factory.bin
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma | pad-to $$(BLOCKSIZE)
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA300
|
|
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
endef
|
|
|
|
define Device/plasmacloud_pa300
|
|
$(Device/plasmacloud_pa300-common)
|
|
DEVICE_MODEL := PA300
|
|
endef
|
|
TARGET_DEVICES += plasmacloud_pa300
|
|
|
|
define Device/plasmacloud_pa300e
|
|
$(Device/plasmacloud_pa300-common)
|
|
DEVICE_MODEL := PA300E
|
|
endef
|
|
TARGET_DEVICES += plasmacloud_pa300e
|
|
|
|
define Device/qca_ap143
|
|
SOC := qca9533
|
|
DEVICE_VENDOR := Qualcomm Atheros
|
|
DEVICE_MODEL := AP143
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
SUPPORTED_DEVICES += ap143
|
|
LOADER_TYPE := bin
|
|
LOADER_FLASH_OFFS := 0x50000
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
|
|
COMPILE := loader-$(1).bin loader-$(1).uImage
|
|
COMPILE/loader-$(1).bin := loader-okli-compile
|
|
COMPILE/loader-$(1).uImage := append-loader-okli $(1) | pad-to 64k | lzma | \
|
|
uImage lzma
|
|
endef
|
|
|
|
define Device/qca_ap143-8m
|
|
$(Device/qca_ap143)
|
|
DEVICE_VARIANT := (8M)
|
|
IMAGE_SIZE := 7744k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | pad-to 6336k | \
|
|
append-loader-okli-uimage $(1) | pad-to 64k
|
|
endef
|
|
TARGET_DEVICES += qca_ap143-8m
|
|
|
|
define Device/qca_ap143-16m
|
|
$(Device/qca_ap143)
|
|
DEVICE_VARIANT := (16M)
|
|
IMAGE_SIZE := 15936k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | pad-to 14528k | \
|
|
append-loader-okli-uimage $(1) | pad-to 64k
|
|
endef
|
|
TARGET_DEVICES += qca_ap143-16m
|
|
|
|
define Device/qihoo_c301
|
|
$(Device/seama)
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Qihoo
|
|
DEVICE_MODEL := C301
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct \
|
|
uboot-envtools
|
|
IMAGE_SIZE := 15744k
|
|
SEAMA_SIGNATURE := wrgac26_qihoo360_360rg
|
|
SUPPORTED_DEVICES += qihoo-c301
|
|
endef
|
|
TARGET_DEVICES += qihoo_c301
|
|
|
|
define Device/qxwlan_e1700ac-v2
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := Qxwlan
|
|
DEVICE_MODEL := E1700AC
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
SUPPORTED_DEVICES += e1700ac-v2
|
|
endef
|
|
|
|
define Device/qxwlan_e1700ac-v2-16m
|
|
$(Device/qxwlan_e1700ac-v2)
|
|
DEVICE_VARIANT := v2 (16M)
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e1700ac-v2-16m
|
|
|
|
define Device/qxwlan_e1700ac-v2-8m
|
|
$(Device/qxwlan_e1700ac-v2)
|
|
DEVICE_VARIANT := v2 (8M)
|
|
IMAGE_SIZE := 7744k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e1700ac-v2-8m
|
|
|
|
define Device/qxwlan_e558-v2
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Qxwlan
|
|
DEVICE_MODEL := E558
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
SUPPORTED_DEVICES += e558-v2
|
|
endef
|
|
|
|
define Device/qxwlan_e558-v2-16m
|
|
$(Device/qxwlan_e558-v2)
|
|
DEVICE_VARIANT := v2 (16M)
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e558-v2-16m
|
|
|
|
define Device/qxwlan_e558-v2-8m
|
|
$(Device/qxwlan_e558-v2)
|
|
DEVICE_VARIANT := v2 (8M)
|
|
IMAGE_SIZE := 7744k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e558-v2-8m
|
|
|
|
define Device/qxwlan_e600g-v2
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := Qxwlan
|
|
DEVICE_MODEL := E600G
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
SUPPORTED_DEVICES += e600g-v2
|
|
endef
|
|
|
|
define Device/qxwlan_e600g-v2-16m
|
|
$(Device/qxwlan_e600g-v2)
|
|
DEVICE_VARIANT := v2 (16M)
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e600g-v2-16m
|
|
|
|
define Device/qxwlan_e600g-v2-8m
|
|
$(Device/qxwlan_e600g-v2)
|
|
DEVICE_VARIANT := v2 (8M)
|
|
IMAGE_SIZE := 7744k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e600g-v2-8m
|
|
|
|
define Device/qxwlan_e600gac-v2
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := Qxwlan
|
|
DEVICE_MODEL := E600GAC
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct
|
|
SUPPORTED_DEVICES += e600gac-v2
|
|
endef
|
|
|
|
define Device/qxwlan_e600gac-v2-16m
|
|
$(Device/qxwlan_e600gac-v2)
|
|
DEVICE_VARIANT := v2 (16M)
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e600gac-v2-16m
|
|
|
|
define Device/qxwlan_e600gac-v2-8m
|
|
$(Device/qxwlan_e600gac-v2)
|
|
DEVICE_VARIANT := v2 (8M)
|
|
IMAGE_SIZE := 7744k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e600gac-v2-8m
|
|
|
|
define Device/qxwlan_e750a-v4
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Qxwlan
|
|
DEVICE_MODEL := E750A
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
SUPPORTED_DEVICES += e750a-v4
|
|
endef
|
|
|
|
define Device/qxwlan_e750a-v4-16m
|
|
$(Device/qxwlan_e750a-v4)
|
|
DEVICE_VARIANT := v4 (16M)
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e750a-v4-16m
|
|
|
|
define Device/qxwlan_e750a-v4-8m
|
|
$(Device/qxwlan_e750a-v4)
|
|
DEVICE_VARIANT := v4 (8M)
|
|
IMAGE_SIZE := 7744k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e750a-v4-8m
|
|
|
|
define Device/qxwlan_e750g-v8
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Qxwlan
|
|
DEVICE_MODEL := E750G
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
SUPPORTED_DEVICES += e750g-v8
|
|
endef
|
|
|
|
define Device/qxwlan_e750g-v8-16m
|
|
$(Device/qxwlan_e750g-v8)
|
|
DEVICE_VARIANT := v8 (16M)
|
|
IMAGE_SIZE := 15936k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e750g-v8-16m
|
|
|
|
define Device/qxwlan_e750g-v8-8m
|
|
$(Device/qxwlan_e750g-v8)
|
|
DEVICE_VARIANT := v8 (8M)
|
|
IMAGE_SIZE := 7744k
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e750g-v8-8m
|
|
|
|
define Device/rosinson_wr818
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := Rosinson
|
|
DEVICE_MODEL := WR818
|
|
IMAGE_SIZE := 15872k
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += rosinson_wr818
|
|
|
|
define Device/samsung_wam250
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Samsung
|
|
DEVICE_MODEL := WAM250
|
|
IMAGE_SIZE := 15872k
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
SUPPORTED_DEVICES += wam250
|
|
endef
|
|
TARGET_DEVICES += samsung_wam250
|
|
|
|
define Device/siemens_ws-ap3610
|
|
SOC := ar7161
|
|
DEVICE_VENDOR := Siemens
|
|
DEVICE_MODEL := WS-AP3610
|
|
IMAGE_SIZE := 14336k
|
|
BLOCKSIZE := 256k
|
|
LOADER_TYPE := bin
|
|
LOADER_FLASH_OFFS := 0x82000
|
|
COMPILE := loader-$(1).bin
|
|
COMPILE/loader-$(1).bin := loader-okli-compile
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49 | loader-okli $(1) 8128 | uImage none
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | uImage none
|
|
endef
|
|
TARGET_DEVICES += siemens_ws-ap3610
|
|
|
|
define Device/sitecom_wlr-7100
|
|
SOC := ar1022
|
|
DEVICE_VENDOR := Sitecom
|
|
DEVICE_MODEL := WLR-7100
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct-smallbuffers kmod-usb2
|
|
IMAGES += factory.dlf
|
|
IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
senao-header -r 0x222 -p 0x53 -t 2
|
|
IMAGE_SIZE := 7488k
|
|
endef
|
|
TARGET_DEVICES += sitecom_wlr-7100
|
|
|
|
define Device/sitecom_wlr-8100
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Sitecom
|
|
DEVICE_MODEL := WLR-8100
|
|
DEVICE_ALT0_VENDOR := Sitecom
|
|
DEVICE_ALT0_MODEL := X8 AC1750
|
|
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2 kmod-usb3
|
|
SUPPORTED_DEVICES += wlr8100
|
|
IMAGES += factory.dlf
|
|
IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | check-size | \
|
|
senao-header -r 0x222 -p 0x56 -t 2
|
|
IMAGE_SIZE := 15424k
|
|
endef
|
|
TARGET_DEVICES += sitecom_wlr-8100
|
|
|
|
define Device/telco_t1
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := Telco
|
|
DEVICE_MODEL := T1
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-net-qmi-wwan \
|
|
kmod-usb-serial-option uqmi -swconfig -uboot-envtools
|
|
IMAGE_SIZE := 16192k
|
|
SUPPORTED_DEVICES += telco_electronics,tel-t1
|
|
endef
|
|
TARGET_DEVICES += telco_t1
|
|
|
|
define Device/teltonika_rut955
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Teltonika
|
|
DEVICE_MODEL := RUT955
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-acm kmod-usb-net-qmi-wwan \
|
|
kmod-usb-serial-option kmod-hwmon-mcp3021 uqmi -uboot-envtools
|
|
IMAGE_SIZE := 15552k
|
|
TPLINK_HWID := 0x35000001
|
|
TPLINK_HWREV := 0x1
|
|
TPLINK_HEADER_VERSION := 1
|
|
KERNEL := kernel-bin | append-dtb | lzma | tplink-v1-header
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | uImage lzma
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs |\
|
|
pad-rootfs | teltonika-fw-fake-checksum | append-string master |\
|
|
append-md5sum-bin | check-size
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) |\
|
|
append-rootfs | pad-rootfs | append-metadata |\
|
|
check-size
|
|
endef
|
|
TARGET_DEVICES += teltonika_rut955
|
|
|
|
define Device/teltonika_rut955-h7v3c0
|
|
$(Device/teltonika_rut955)
|
|
DEVICE_VARIANT := H7V3C0
|
|
endef
|
|
TARGET_DEVICES += teltonika_rut955-h7v3c0
|
|
|
|
define Device/trendnet_tew-823dru
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Trendnet
|
|
DEVICE_MODEL := TEW-823DRU
|
|
DEVICE_VARIANT := v1.0R
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
SUPPORTED_DEVICES += tew-823dru
|
|
IMAGE_SIZE := 15296k
|
|
IMAGES := factory.bin sysupgrade.bin
|
|
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
|
|
pad-rootfs
|
|
IMAGE/factory.bin := $$(IMAGE/default) | pad-offset $$$$(IMAGE_SIZE) 26 | \
|
|
append-string 00AP135AR9558-RT-131129-00 | check-size
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | \
|
|
check-size
|
|
endef
|
|
TARGET_DEVICES += trendnet_tew-823dru
|
|
|
|
define Device/wallys_dr531
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := Wallys
|
|
DEVICE_MODEL := DR531
|
|
DEVICE_PACKAGES := kmod-usb2 rssileds
|
|
IMAGE_SIZE := 7808k
|
|
SUPPORTED_DEVICES += dr531
|
|
endef
|
|
TARGET_DEVICES += wallys_dr531
|
|
|
|
define Device/wd_mynet-n750
|
|
$(Device/seama)
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Western Digital
|
|
DEVICE_MODEL := My Net N750
|
|
IMAGE_SIZE := 15872k
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
SEAMA_SIGNATURE := wrgnd13_wd_av
|
|
SUPPORTED_DEVICES += mynet-n750
|
|
endef
|
|
TARGET_DEVICES += wd_mynet-n750
|
|
|
|
define Device/wd_mynet-wifi-rangeextender
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Western Digital
|
|
DEVICE_MODEL := My Net Wi-Fi Range Extender
|
|
DEVICE_PACKAGES := rssileds nvram -swconfig
|
|
IMAGE_SIZE := 7808k
|
|
ADDPATTERN_ID := mynet-rext
|
|
ADDPATTERN_VERSION := 1.00.01
|
|
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | cybertan-trx | \
|
|
addpattern | append-metadata
|
|
SUPPORTED_DEVICES += mynet-rext
|
|
endef
|
|
TARGET_DEVICES += wd_mynet-wifi-rangeextender
|
|
|
|
define Device/winchannel_wb2000
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Winchannel
|
|
DEVICE_MODEL := WB2000
|
|
IMAGE_SIZE := 15872k
|
|
DEVICE_PACKAGES := kmod-i2c-gpio kmod-rtc-ds1307 kmod-usb2 \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += winchannel_wb2000
|
|
|
|
define Device/xiaomi_mi-router-4q
|
|
SOC := qca9561
|
|
DEVICE_VENDOR := Xiaomi
|
|
DEVICE_MODEL := Mi Router 4Q
|
|
IMAGE_SIZE := 14336k
|
|
endef
|
|
TARGET_DEVICES += xiaomi_mi-router-4q
|
|
|
|
define Device/yuncore_a770
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := YunCore
|
|
DEVICE_MODEL := A770
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct
|
|
IMAGE_SIZE := 16000k
|
|
IMAGES += tftp.bin
|
|
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
|
|
endef
|
|
TARGET_DEVICES += yuncore_a770
|
|
|
|
define Device/yuncore_a782
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := YunCore
|
|
DEVICE_MODEL := A782
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
|
IMAGE_SIZE := 16000k
|
|
IMAGES += tftp.bin
|
|
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
|
|
endef
|
|
TARGET_DEVICES += yuncore_a782
|
|
|
|
define Device/yuncore_xd4200
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := YunCore
|
|
DEVICE_MODEL := XD4200
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
|
IMAGE_SIZE := 16000k
|
|
IMAGES += tftp.bin
|
|
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
|
|
endef
|
|
TARGET_DEVICES += yuncore_xd4200
|
|
|
|
define Device/ziking_cpe46b
|
|
SOC := ar9330
|
|
DEVICE_VENDOR := ZiKing
|
|
DEVICE_MODEL := CPE46B
|
|
IMAGE_SIZE := 8000k
|
|
DEVICE_PACKAGES := kmod-i2c-gpio
|
|
endef
|
|
TARGET_DEVICES += ziking_cpe46b
|
|
|
|
define Device/zbtlink_zbt-wd323
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := ZBT
|
|
DEVICE_MODEL := WD323
|
|
IMAGE_SIZE := 16000k
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-i2c-gpio kmod-rtc-pcf8563 \
|
|
kmod-usb-serial-cp210x uqmi
|
|
endef
|
|
TARGET_DEVICES += zbtlink_zbt-wd323
|
|
|
|
define Device/zyxel_nbg6616
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := ZyXEL
|
|
DEVICE_MODEL := NBG6616
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-rtc-pcf8563 \
|
|
kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
IMAGE_SIZE := 15232k
|
|
RAS_BOARD := NBG6616
|
|
RAS_ROOTFS_SIZE := 14464k
|
|
RAS_VERSION := "OpenWrt Linux-$(LINUX_VERSION)"
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
append-rootfs | pad-rootfs | pad-to 64k | check-size | zyxel-ras-image
|
|
SUPPORTED_DEVICES += nbg6616
|
|
endef
|
|
TARGET_DEVICES += zyxel_nbg6616
|