ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-28 01:28:59 +00:00
Code Issues Actions 10 Packages Projects Releases Wiki Activity
6378d72ef6
openwrt/target/linux/ath79/image/nand.mk
Lech Perczak 8c78a13bfc ath79: support ZTE MF286 
ZTE MF286 is an indoor LTE category 6 CPE router with simultaneous
dual-band 802.11ac plus 802.11n Wi-Fi radios and quad-port gigabit
Ethernet switch, FXS and external USB 2.0 port.

Hardware highlights:
- CPU: QCA9563 SoC at 775MHz,
- RAM: 128MB DDR2,
- NOR Flash: MX25L1606E 2MB SPI Flash, for U-boot only,
- NAND Flash: GD5F1G04UBYIG 128MB SPI NAND-Flash, for all other data,
- Wi-Fi 5GHz: QCA9882 2x2 MIMO 802.11ac radio,
- WI-Fi 2.4GHz: QCA9563 3x3 MIMO 802.11n radio,
- Switch: QCA8337v2 4-port gigabit Ethernet, with single SGMII CPU port,
- WWAN: MDM9230-based category 6 internal LTE modem in extended
  mini-PCIE form factor, with 3 internal antennas and 2 external antenna
  connections, single mini-SIM slot. Modem model identified as MF270,
- FXS: one external ATA port (handled entirely by modem part) with two
  physical connections in parallel,
- USB: Single external USB 2.0 port,
- Switches: power switch, WPS, Wi-Fi and reset buttons,
- LEDs: Wi-Fi, Test (internal). Rest of LEDs (Phone, WWAN, Battery,
  Signal state) handled entirely by modem. 4 link status LEDs handled by
  the switch on the backside.
- Battery: 3Ah 1-cell Li-Ion replaceable battery, with charging and
  monitoring handled by modem.
- Label MAC device: eth0

Console connection: connector X2 is the console port, with the following
pinout, starting from pin 1, which is the topmost pin when the board is
upright:
- VCC (3.3V). Do not use unless you need to source power for the
  converer from it.
- TX
- RX
- GND
Default port configuration in U-boot as well as in stock firmware is
115200-8-N-1.

Installation:
Due to different flash layout from stock firmware, sysupgrade from
within stock firmware is impossible, despite it's based on QSDK which
itself is based on OpenWrt.

STEP 0: Stock firmware update:
As installing OpenWrt cuts you off from official firmware updates for
the modem part, it is recommended to update the stock firmware to latest
version before installation, to have built-in modem at the latest firmware
version.

STEP 1: gaining root shell:

Method 1:
This works if busybox has telnetd compiled in the binary.
If this does not work, try method 2.

Using well-known exploit to start telnetd on your router - works
only if Busybox on stock firmware has telnetd included:
- Open stock firmware web interface
- Navigate to "URL filtering" section by going to "Advanced settings",
  then "Firewall" and finally "URL filter".
- Add an entry ending with "&&telnetd&&", for example
  "http://hostname/&&telnetd&&".
- telnetd will immediately listen on port 4719.
- After connecting to telnetd use "admin/admin" as credentials.

Method 2:
This works if busybox does not have telnetd compiled in. Notably, this
is the case in DNA.fi firmware.
If this does not work, try method 3.

- Set IP of your computer to 192.168.1.22.
- Have a TFTP server running at that address
- Download MIPS build of busybox including telnetd, for example from:
  https://busybox.net/downloads/binaries/1.21.1/busybox-mips
  and put it in it's root directory. Rename it as "telnetd".
- As previously, login to router's web UI and navigate to "URL
  filtering"
- Using "Inspect" feature, extend "maxlength" property of the input
  field named "addURLFilter", so it looks like this:
  <input type="text" name="addURLFilter" id="addURLFilter" maxlength="332"
    class="required form-control">
- Stay on the page - do not navigate anywhere
- Enter "http://aa&zte_debug.sh 192.168.1.22 telnetd" as a filter.
- Save the settings. This will download the telnetd binary over tftp and
  execute it. You should be able to log in at port 23, using
  "admin/admin" as credentials.

Method 3:
If the above doesn't work, use the serial console - it exposes root shell
directly without need for login. Some stock firmwares, notably one from
finnish DNA operator lack telnetd in their builds.

STEP 2: Backing up original software:
As the stock firmware may be customized by the carrier and is not
officially available in the Internet, IT IS IMPERATIVE to back up the
stock firmware, if you ever plan to returning to stock firmware.

Method 1: after booting OpenWrt initramfs image via TFTP:
PLEASE NOTE: YOU CANNOT DO THIS IF USING INTERMEDIATE FIRMWARE FOR INSTALLATION.
- Dump stock firmware located on stock kernel and ubi partitions:

  ssh root@192.168.1.1: cat /dev/mtd4 > mtd4_kernel.bin
  ssh root@192.168.1.1: cat /dev/mtd8 > mtd8_ubi.bin

And keep them in a safe place, should a restore be needed in future.

Method 2: using stock firmware:
- Connect an external USB drive formatted with FAT or ext4 to the USB
  port.
- The drive will be auto-mounted to /var/usb_disk
- Check the flash layout of the device:

  cat /proc/mtd

  It should show the following:
  mtd0: 00080000 00010000 "uboot"
  mtd1: 00020000 00010000 "uboot-env"
  mtd2: 00140000 00020000 "fota-flag"
  mtd3: 00140000 00020000 "caldata"
  mtd4: 00140000 00020000 "mac"
  mtd5: 00600000 00020000 "cfg-param"
  mtd6: 00140000 00020000 "oops"
  mtd7: 00800000 00020000 "web"
  mtd8: 00300000 00020000 "kernel"
  mtd9: 01f00000 00020000 "rootfs"
  mtd10: 01900000 00020000 "data"
  mtd11: 03200000 00020000 "fota"

  Differences might indicate that this is NOT a vanilla MF286 device but
  one of its later derivatives.
- Copy over all MTD partitions, for example by executing the following:

  for i in 0 1 2 3 4 5 6 7 8 9 10 11; do cat /dev/mtd$i > \
  /var/usb_disk/mtd$i; done

- If the count of MTD partitions is different, this might indicate that
  this is not a standard MF286 device, but one of its later derivatives.
- (optionally) rename the files according to MTD partition names from
  /proc/mtd
- Unmount the filesystem:

  umount /var/usb_disk; sync

  and then remove the drive.
- Store the files in safe place if you ever plan to return to stock
  firmware. This is especially important, because stock firmware for
  this device is not available officially, and is usually customized by
  the mobile providers.

STEP 3: Booting initramfs image:

Method 1: using serial console (RECOMMENDED):
- Have TFTP server running, exposing the OpenWrt initramfs image, and
  set your computer's IP address as 192.168.1.22. This is the default
  expected by U-boot. You may wish to change that, and alter later
  commands accordingly.
- Connect the serial console if you haven't done so already,
- Interrupt boot sequence by pressing any key in U-boot when prompted
- Use the following commands to boot OpenWrt initramfs through TFTP:

  setenv serverip 192.168.1.22
  setenv ipaddr 192.168.1.1
  tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin
  bootm 0x81000000

  (Replace server IP and router IP as needed). There is no  emergency
  TFTP boot sequence triggered by buttons, contrary to MF283+.
- When OpenWrt initramfs finishes booting, proceed to actual
  installation.

Method 2: using initramfs image as temporary boot kernel
This exploits the fact, that kernel and rootfs MTD devices are
consecutive on NAND flash, so from within stock image, an initramfs can
be written to this area and booted by U-boot on next reboot, because it
uses "nboot" command which isn't limited by kernel partition size.
- Download the initramfs-kernel.bin image
- Split the image into two parts on 3MB partition size boundary, which
  is the size of kernel partition. Pad the output of second file to
  eraseblock size:

  dd if=openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin \
  bs=128k count=24 \
  of=openwrt-ath79-zte_mf286-intermediate-kernel.bin

  dd if=openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin \
  bs=128k skip=24 conv=sync \
  of=openwrt-ath79-zte_mf286-intermediate-rootfs.bin

- Copy over /usr/bin/flash_eraseall and /usr/bin/nandwrite utilities to
  /tmp. This is CRITICAL for installation, as erasing rootfs will cut
  you off from those tools on flash!

- After backing up the previous MTD contents, write the images to the
  respective MTD devices:

  /tmp/flash_eraseall /dev/<kernel-mtd>

  /tmp/nandwrite /dev/<kernel-mtd> \
  /var/usb_disk/openwrt-ath79-zte_mf286-intermediate-kernel.bin

  /tmp/flash_eraseall /dev/<kernel-mtd>

  /tmp/nandwrite /dev/<rootfs-mtd> \
  /var/usb_disk/openwrt-ath79-zte_mf286-intermediate-rootfs.bin

- Ensure that no bad blocks were present on the devices while writing.
  If they were present, you may need to vary the split  between
  kernel and rootfs parts, so U-boot reads a valid uImage after skipping
  the bad blocks. If it fails, you will be left with method 3 (below).
- If write is OK, reboot the device, it will reboot to OpenWrt
  initramfs:

  reboot -f

- After rebooting, SSH into the device and use sysupgrade to perform
  proper installation.

Method 3: using built-in TFTP recovery (LAST RESORT):
- With that method, ensure you have complete backup of system's NAND
  flash first. It involves deliberately erasing the kernel.
- Download "-initramfs-kernel.bin" image for the device.
- Prepare the recovery image by prepending 8MB of zeroes to the image,
  and name it root_uImage:

  dd if=/dev/zero of=padding.bin bs=8M count=1

  cat padding.bin openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin >
  root_uImage

- Set up a TFTP server at 192.0.0.1/8. Router will use random address
  from that range.
- Put the previously generated "root_uImage" into TFTP server root
  directory.
- Deliberately erase "kernel" partition" using stock firmware after
  taking backup. THIS IS POINT OF NO RETURN.
- Restart the device. U-boot will attempt flashing the recovery
  initramfs image, which will let you perform actual installation using
  sysupgrade. This might take a considerable time, sometimes the router
  doesn't establish Ethernet link properly right after booting. Be
  patient.
- After U-boot finishes flashing, the LEDs of switch ports will all
  light up. At this moment, perform power-on reset, and wait for OpenWrt
  initramfs to finish booting. Then proceed to actual installation.

STEP 4: Actual installation:
- scp the sysupgrade image to the device:

  scp openwrt-ath79-nand-zte_mf286-squashfs-sysupgrade.bin \
  root@192.168.1.1:/tmp/

- ssh into the device and execute sysupgrade:

  sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286-squashfs-sysupgrade.bin

- Wait for router to reboot to full OpenWrt.

STEP 5: WAN connection establishment
Since the router is equipped with LTE modem as its main WAN interface, it
might be useful to connect to the Internet right away after
installation. To do so, please put the following entries in
/etc/config/network, replacing the specific configuration entries with
one needed for your ISP:

config interface 'wan'
        option proto 'qmi'
        option device '/dev/cdc-wdm0'
        option auth '<auth>' # As required, usually 'none'
        option pincode '<pin>' # If required by SIM
        option apn '<apn>' # As required by ISP
        option pdptype '<pdp>' # Typically 'ipv4', or 'ipv4v6' or 'ipv6'

For example, the following works for most polish ISPs
config interface 'wan'
        option proto 'qmi'
        option device '/dev/cdc-wdm0'
        option auth 'none'
        option apn 'internet'
        option pdptype 'ipv4'

If you have build with LuCI, installing luci-proto-qmi helps with this
task.

Restoring the stock firmware:

Preparation:
If you took your backup using stock firmware, you will need to
reassemble the partitions into images to be restored onto the flash. The
layout might differ from ISP to ISP, this example is based on generic stock
firmware.
The only partitions you really care about are "web", "kernel", and
"rootfs". For easy padding and possibly restoring configuration, you can
concatenate most of them into images written into "ubi" meta-partition
in OpenWrt. To do so, execute something like:

cat mtd5_cfg-param.bin mtd6-oops.bin mtd7-web.bin mtd9-rootfs.bin > \
mtd8-ubi_restore.bin

You can skip the "fota" partition altogether,
it is used only for stock firmware update purposes and can be overwritten
safely anyway. The same is true for "data" partition which on my device
was found to be unused at all. Restoring mtd5_cfg-param.bin will restore
the stock firmware configuration you had before.

Method 1: Using initramfs:
- Boot to initramfs as in step 3:
- Completely detach ubi0 partition using ubidetach /dev/ubi0_0
- Look up the kernel and ubi partitions in /proc/mtd
- Copy over the stock kernel image using scp to /tmp
- Erase kernel and restore stock kernel:
  (scp mtd4_kernel.bin root@192.168.1.1:/tmp/)
  mtd write <kernel_mtd> mtd4_kernel.bin
  rm mtd4_kernel.bin
- Copy over the stock partition backups one-by-one using scp to /tmp, and
  restore them individually. Otherwise you might run out of space in
  tmpfs:

  (scp mtd3_ubiconcat0.bin root@192.168.1.1:/tmp/)

  mtd write <ubiconcat0_mtd> mtd3_ubiconcat0.bin
  rm mtd3_ubiconcat0.bin

  (scp mtd5_ubiconcat1.bin root@192.168.1.1:/tmp/)

  mtd write <ubiconcat1_mtd> mtd5_ubiconcat1.bin
  rm mtd5_ubiconcat1.bin

- If the write was correct, force a device reboot with

  reboot -f

Method 2: Using live OpenWrt system (NOT RECOMMENDED):
- Prepare a USB flash drive contatining MTD backup files
- Ensure you have kmod-usb-storage and filesystem driver installed for
  your drive
- Mount your flash drive

  mkdir /tmp/usb

  mount /dev/sda1 /tmp/usb

- Remount your UBI volume at /overlay to R/O

  mount -o remount,ro /overlay

- Write back the kernel and ubi partitions from USB drive

  cd /tmp/usb
  mtd write mtd4_kernel.bin /dev/<kernel_mtd>

  mtd write mtd8_ubi.bin /dev/<kernel_ubi>

- If everything went well, force a device reboot with
  reboot -f

Last image may be truncated a bit due to lack of space in RAM, but this will happen over "fota"
MTD partition which may be safely erased after reboot anyway.

Method 3: using built-in TFTP recovery (LAST RESORT):
- Assemble a recovery rootfs image from backup of stock partitions by
  concatenating "web", "kernel", "rootfs" images dumped from the device,
  as "root_uImage"
- Use it in place of "root_uImage" recovery initramfs image as in the
  TFTP pre-installation method.

Quirks and known issues
- Kernel partition size is increased to 4MB compared to stock 3MB, to
  accomodate future kernel updates - at this moment OpenWrt 5.10 kernel
  image is at 2.5MB which is dangerously close to the limit. This has no
  effect on booting the system - but keep that in mind when reassembling
  an image to restore stock firmware.
- uqmi seems to be unable to change APN manually, so please use the one
  you used before in stock firmware first. If you need to change it,
  please use protocok '3g' to establish connection once, or use the
  following command to change APN (and optionally IP type) manually:
  echo -ne 'AT+CGDCONT=1,"IP","<apn>' > /dev/ttyUSB0
- The only usable LED as a "system LED" is the green debug LED hidden
  inside the case. All other LEDs are controlled by modem, on which the
  router part has some influence only on Wi-Fi LED.
- Wi-Fi LED currently doesn't work while under OpenWrt, despite having
  correct GPIO mapping. All other LEDs are controlled by modem,
  including this one in stock firmware. GPIO19, mapped there only acts
  as a gate, while the actual signal source seems to be 5GHz Wi-Fi
  radio, however it seems it is not the LED exposed by ath10k as
  ath10k-phy0.
- GPIO5 used for modem reset is a suicide switch, causing a hardware
  reset of whole board, not only the modem. It is attached to
  gpio-restart driver, to restart the modem on reboot as well, to ensure
  QMI connectivity after reboot, which tends to fail otherwise.
- Modem, as in MF283+, exposes root shell over ADB - while not needed
  for OpenWrt operation at all - have fun lurking around.
- MAC address shift for 5GHz Wi-Fi used in stock firmware is
  0x320000000000, which is impossible to encode in the device tree, so I
  took the liberty of using MAC address increment of 1 for it, to ensure
  different BSSID for both Wi-Fi interfaces.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-02-05 12:14:08 +01:00

347 lines
9.8 KiB
Makefile
Raw Blame History

define Build/dongwon-header
head -c 4 $@ > $@.tmp
head -c 8 /dev/zero >> $@.tmp
tail -c +9 $@ >> $@.tmp
( \
header_crc="$$(head -c 68 $@.tmp | gzip -c | \
tail -c 8 | od -An -N4 -tx4 --endian little | tr -d ' \n')"; \
printf "$$(echo $$header_crc | sed 's/../\\x&/g')" | \
dd of=$@.tmp bs=4 count=1 seek=1 conv=notrunc \
)
mv $@.tmp $@
endef
# attention: only zlib compression is allowed for the boot fs
define Build/zyxel-buildkerneljffs
mkdir -p $@.tmp/boot
cp $@ $@.tmp/boot/vmlinux.lzma.uImage
$(STAGING_DIR_HOST)/bin/mkfs.jffs2 \
--big-endian --squash-uids -v -e 128KiB -q -f -n -x lzma -x rtime \
-o $@ \
-d $@.tmp
rm -rf $@.tmp
endef
define Build/zyxel-factory
let \
maxsize="$(subst k,* 1024,$(RAS_ROOTFS_SIZE))"; \
let size="$$(stat -c%s $@)"; \
if [ $$size -lt $$maxsize ]; then \
$(STAGING_DIR_HOST)/bin/mkrasimage \
-b $(RAS_BOARD) \
-v $(RAS_VERSION) \
-r $@ \
-s $$maxsize \
-o $@.new \
-l 131072 \
&& mv $@.new $@ ; \
fi
endef
define Device/8dev_rambutan
SOC := qca9557
DEVICE_VENDOR := 8devices
DEVICE_MODEL := Rambutan
DEVICE_PACKAGES := kmod-usb2
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
KERNEL_IN_UBI := 1
IMAGES := factory.bin sysupgrade.tar
IMAGE/sysupgrade.tar := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-ubi
endef
TARGET_DEVICES += 8dev_rambutan
define Device/aerohive_hiveap-121
SOC := ar9344
DEVICE_VENDOR := Aerohive
DEVICE_MODEL := HiveAP 121
DEVICE_PACKAGES := kmod-usb2
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 116m
KERNEL_SIZE := 5120k
UBINIZE_OPTS := -E 5
SUPPORTED_DEVICES += hiveap-121
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
check-size
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += aerohive_hiveap-121
define Device/domywifi_dw33d
SOC := qca9558
DEVICE_VENDOR := DomyWifi
DEVICE_MODEL := DW33D
DEVICE_PACKAGES := kmod-usb2 kmod-usb-storage kmod-usb-ledtrig-usbport \
kmod-ath10k-ct ath10k-firmware-qca988x-ct
KERNEL_SIZE := 5120k
IMAGE_SIZE := 98304k
BLOCKSIZE := 128k
PAGESIZE := 2048
UBINIZE_OPTS := -E 5
IMAGES += factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
check-size
endef
TARGET_DEVICES += domywifi_dw33d
define Device/dongwon_dw02-412h
SOC := qca9557
DEVICE_VENDOR := Dongwon T&I
DEVICE_MODEL := DW02-412H
DEVICE_ALT0_VENDOR := KT
DEVICE_ALT0_MODEL := GiGA WiFi home
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
KERNEL_SIZE := 8192k
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL := $$(KERNEL) | dongwon-header
KERNEL_INITRAMFS := $$(KERNEL)
UBINIZE_OPTS := -E 5
IMAGES += factory.img
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
check-size
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
define Device/dongwon_dw02-412h-64m
$(Device/dongwon_dw02-412h)
DEVICE_VARIANT := (64M)
DEVICE_ALT0_VARIANT := (64M)
IMAGE_SIZE := 49152k
endef
TARGET_DEVICES += dongwon_dw02-412h-64m
define Device/dongwon_dw02-412h-128m
$(Device/dongwon_dw02-412h)
DEVICE_VARIANT := (128M)
DEVICE_ALT0_VARIANT := (128M)
IMAGE_SIZE := 114688k
endef
TARGET_DEVICES += dongwon_dw02-412h-128m
define Device/glinet_gl-ar300m-common-nand
SOC := qca9531
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-AR300M
DEVICE_PACKAGES := kmod-usb2
KERNEL_SIZE := 4096k
IMAGE_SIZE := 16000k
PAGESIZE := 2048
VID_HDR_OFFSET := 2048
endef
define Device/glinet_gl-ar300m-nand
$(Device/glinet_gl-ar300m-common-nand)
DEVICE_VARIANT := NAND
BLOCKSIZE := 128k
IMAGES += factory.img
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
SUPPORTED_DEVICES += glinet,gl-ar300m-nor
endef
TARGET_DEVICES += glinet_gl-ar300m-nand
define Device/glinet_gl-ar300m-nor
$(Device/glinet_gl-ar300m-common-nand)
DEVICE_VARIANT := NOR
SUPPORTED_DEVICES += glinet,gl-ar300m-nand gl-ar300m
endef
TARGET_DEVICES += glinet_gl-ar300m-nor
define Device/glinet_gl-ar750s-common
SOC := qca9563
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-AR750S
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct kmod-usb2 \
kmod-usb-storage block-mount
IMAGE_SIZE := 16000k
endef
define Device/glinet_gl-ar750s-nor-nand
$(Device/glinet_gl-ar750s-common)
DEVICE_VARIANT := NOR/NAND
KERNEL_SIZE := 4096k
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
SUPPORTED_DEVICES += glinet,gl-ar750s-nor
endef
TARGET_DEVICES += glinet_gl-ar750s-nor-nand
define Device/glinet_gl-ar750s-nor
$(Device/glinet_gl-ar750s-common)
DEVICE_VARIANT := NOR
SUPPORTED_DEVICES += gl-ar750s glinet,gl-ar750s glinet,gl-ar750s-nor-nand
endef
TARGET_DEVICES += glinet_gl-ar750s-nor
define Device/glinet_gl-e750
SOC := qca9531
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-E750
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct kmod-usb2
SUPPORTED_DEVICES += gl-e750
KERNEL_SIZE := 4096k
IMAGE_SIZE := 131072k
PAGESIZE := 2048
VID_HDR_OFFSET := 2048
BLOCKSIZE := 128k
IMAGES += factory.img
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += glinet_gl-e750
define Device/glinet_gl-xe300
SOC := qca9531
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-XE300
DEVICE_PACKAGES := kmod-usb2 block-mount kmod-usb-serial-ch341
KERNEL_SIZE := 4096k
IMAGE_SIZE := 131072k
PAGESIZE := 2048
VID_HDR_OFFSET := 2048
BLOCKSIZE := 128k
IMAGES += factory.img
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += glinet_gl-xe300
# fake rootfs is mandatory, pad-offset 129 equals (2 * uimage_header + 0xff)
define Device/netgear_ath79_nand
DEVICE_VENDOR := NETGEAR
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
KERNEL_SIZE := 4096k
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 25600k
KERNEL := kernel-bin | append-dtb | lzma -d20 | \
pad-offset $$(KERNEL_SIZE) 129 | uImage lzma | \
append-string -e '\xff' | \
append-uImage-fakehdr filesystem $$(UIMAGE_MAGIC)
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma -d20 | uImage lzma
IMAGES := sysupgrade.bin factory.img
IMAGE/factory.img := append-kernel | append-ubi | netgear-dni | \
check-size
IMAGE/sysupgrade.bin := sysupgrade-tar | check-size | append-metadata
UBINIZE_OPTS := -E 5
endef
define Device/netgear_r6100
SOC := ar9344
DEVICE_MODEL := R6100
UIMAGE_MAGIC := 0x36303030
NETGEAR_BOARD_ID := R6100
NETGEAR_HW_ID := 29764434+0+128+128+2x2+2x2
$(Device/netgear_ath79_nand)
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += netgear_r6100
define Device/netgear_wndr3700-v4
SOC := ar9344
DEVICE_MODEL := WNDR3700
DEVICE_VARIANT := v4
UIMAGE_MAGIC := 0x33373033
NETGEAR_BOARD_ID := WNDR3700v4
NETGEAR_HW_ID := 29763948+128+128
$(Device/netgear_ath79_nand)
endef
TARGET_DEVICES += netgear_wndr3700-v4
define Device/netgear_wndr4300
SOC := ar9344
DEVICE_MODEL := WNDR4300
UIMAGE_MAGIC := 0x33373033
NETGEAR_BOARD_ID := WNDR4300
NETGEAR_HW_ID := 29763948+0+128+128+2x2+3x3
$(Device/netgear_ath79_nand)
endef
TARGET_DEVICES += netgear_wndr4300
define Device/netgear_wndr4300sw
SOC := ar9344
DEVICE_MODEL := WNDR4300SW
UIMAGE_MAGIC := 0x33373033
NETGEAR_BOARD_ID := WNDR4300SW
NETGEAR_HW_ID := 29763948+0+128+128+2x2+3x3
$(Device/netgear_ath79_nand)
endef
TARGET_DEVICES += netgear_wndr4300sw
define Device/netgear_wndr4300tn
SOC := ar9344
DEVICE_MODEL := WNDR4300TN
UIMAGE_MAGIC := 0x33373033
NETGEAR_BOARD_ID := WNDR4300TN
NETGEAR_HW_ID := 29763948+0+128+128+2x2+3x3
$(Device/netgear_ath79_nand)
endef
TARGET_DEVICES += netgear_wndr4300tn
define Device/netgear_wndr4300-v2
SOC := qca9563
DEVICE_MODEL := WNDR4300
DEVICE_VARIANT := v2
UIMAGE_MAGIC := 0x27051956
NETGEAR_BOARD_ID := WNDR4500series
NETGEAR_HW_ID := 29764821+2+128+128+3x3+3x3+5508012175
$(Device/netgear_ath79_nand)
endef
TARGET_DEVICES += netgear_wndr4300-v2
define Device/netgear_wndr4500-v3
SOC := qca9563
DEVICE_MODEL := WNDR4500
DEVICE_VARIANT := v3
UIMAGE_MAGIC := 0x27051956
NETGEAR_BOARD_ID := WNDR4500series
NETGEAR_HW_ID := 29764821+2+128+128+3x3+3x3+5508012173
$(Device/netgear_ath79_nand)
endef
TARGET_DEVICES += netgear_wndr4500-v3
define Device/zte_mf286
SOC := qca9563
DEVICE_VENDOR := ZTE
DEVICE_MODEL := MF286
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-ath10k-ct \
ath10k-firmware-qca988x-ct kmod-usb-net-qmi-wwan kmod-usb-serial-option \
uqmi
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_SIZE := 4096k
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += zte_mf286
define Device/zyxel_nbg6716
SOC := qca9558
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := NBG6716
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-ath10k-ct \
ath10k-firmware-qca988x-ct
RAS_BOARD := NBG6716
RAS_ROOTFS_SIZE := 29696k
RAS_VERSION := "OpenWrt Linux-$(LINUX_VERSION)"
KERNEL_SIZE := 4096k
BLOCKSIZE := 128k
PAGESIZE := 2048
LOADER_TYPE := bin
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | uImage none | \
zyxel-buildkerneljffs | check-size 4096k
IMAGES := sysupgrade.tar sysupgrade-4M-Kernel.bin factory.bin
IMAGE/sysupgrade.tar/squashfs := append-rootfs | pad-to $$$$(BLOCKSIZE) | \
sysupgrade-tar rootfs=$$$$@ | append-metadata
IMAGE/sysupgrade-4M-Kernel.bin/squashfs := append-kernel | \
pad-to $$$$(KERNEL_SIZE) | append-ubi | pad-to 263192576 | gzip
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
zyxel-factory
UBINIZE_OPTS := -E 5
endef
TARGET_DEVICES += zyxel_nbg6716
Reference in New Issue View Git Blame Copy Permalink