ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2025-01-20 03:36:29 +00:00
Code Issues Actions 4 Packages Projects Releases Wiki Activity
4e46ae1f69
openwrt/target/linux/kirkwood/image/Makefile
Pawel Dembicki 4e46ae1f69 kirkwood: add support for NETGEAR ReadyNAS Duo v2 
NETGEAR ReadyNAS Duo v2 is a NAS based on Marvell kirkwood SoC.

Specification:
 - Processor Marvell 88F6282 (1.6 GHz)
 - 256MB RAM
 - 128MB NAND
 - 1x GBE LAN port (PHY: Marvell 88E1318)
 - 1x USB 2.0
 - 2x USB 3.0
 - 2x SATA
 - 3x button
 - 5x leds
 - serial on J5 connector accessible from rear panel
   (115200 8N1) (VCC,TX,RX,GND) (3V3 LOGIC!)

Installation by USB + serial:
  - Copy initramfs image to fat32 usb drive
  - Connect pendrive to USB 2.0 front socket
  - Connect serial console
  - Stop booting in u-boot
  - Do:
	usb reset
        setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
        setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
        saveenv
	fatload usb 0:1 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
	bootm 0x1200000
  - copy sysupgrade image via ssh.
  - run sysupgrade

Installation by TFTP + serial:
  - Setup TFTP server and copy initramfs image
  - Connect serial console
  - Stop booting in u-boot
  - Do:
	setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
	setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
	saveenv
	setenv serverip 192.168.1.1
	setenv ipaddr 192.168.1.2
	tftpboot 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
	bootm 0x1200000
  - copy sysupgrade image via ssh.
  - run sysupgrade

Known issues:
  - Power button and PHY INTn pin are connected to the same GPIO. It
    causes that every network restart button is pressed in system.
    As workaround, button is used as regular BTN_1.

For more info please look at file:
RND_5.3.13_WW.src/u-boot/board/mv_feroceon/mv_hal/usibootup/usibootup.c
from Netgear GPL sources.

Tested-by: Raylynn Knight <rayknight@me.com>
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-12-29 20:35:57 +01:00

298 lines
8.6 KiB
Makefile
Raw Blame History

# SPDX-License-Identifier: GPL-2.0-only
#
# Copyright (C) 2009-2013 OpenWrt.org
include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk
KERNEL_LOADADDR:=0x8000
# Some info about Ctera firmware:
# 1. It's simple tar file (GNU standard), but it must have ".firm" suffix.
# 2. It contains two images: kernel and romdisk. Both are required.
# 3. Every image has header and trailer file.
# 4. The struct of tar firmware is: header kernel trailer header romdisk trailer
# 5. In header file are some strings used to describe image. It was decoded from
# factory image.
# 6. Version format in header file is restricted by Original FW.
# 7. Trailer file contains MD5 sum string of header and image file.
# 8. Firmware file must have <=24MB size.
define Build/ctera-firmware
mkdir -p $@.tmp
# Prepare header and trailer file for kernel
echo "# CTera firmware information file" > $@.tmp/header
echo "image_type=kernel" >> $@.tmp/header
echo "arch=Kirkwood" >> $@.tmp/header
echo "board=Any" >> $@.tmp/header
echo "version=3.1.22.30669" >> $@.tmp/header
echo "kernel_cmd=console=ttyS0,115200 earlyprintk" >> $@.tmp/header
echo "date=$$(date $(if $(SOURCE_DATE_EPOCH),-d@$(SOURCE_DATE_EPOCH)))" \
>> $@.tmp/header
cp $@ $@.tmp/kernel
echo "MD5=$$(cat $@.tmp/header $@.tmp/kernel | $(MKHASH) md5)" \
> $@.tmp/trailer
tar $(if $(SOURCE_DATE_EPOCH),--mtime="@$(SOURCE_DATE_EPOCH)") \
-H gnu -C $@.tmp -cf $@.tar header kernel trailer
# Prepare header and trailer file for fake romdisk
echo "# CTera firmware information file" > $@.tmp/header
echo "image_type=romdisk" >> $@.tmp/header
echo "initrd=yes" >> $@.tmp/header
echo "arch=Kirkwood" >> $@.tmp/header
echo "board=Any" >> $@.tmp/header
echo "version=3.1.22.30669" >> $@.tmp/header
echo "date=$$(date $(if $(SOURCE_DATE_EPOCH),-d@$(SOURCE_DATE_EPOCH)))" \
>> $@.tmp/header
rm -f $@
touch $@
$(call Build/append-uImage-fakehdr, ramdisk)
cp $@ $@.tmp/romdisk
echo "MD5=$$(cat $@.tmp/header $@.tmp/romdisk | $(MKHASH) md5)" \
> $@.tmp/trailer
tar $(if $(SOURCE_DATE_EPOCH),--mtime="@$(SOURCE_DATE_EPOCH)") \
-H gnu -C $@.tmp -rf $@.tar header romdisk trailer
mv $@.tar $@
rm -rf $@.tmp
endef
define Device/kernel-size-migration
DEVICE_COMPAT_VERSION := 2.0
DEVICE_COMPAT_MESSAGE := Partition design has changed compared to \
older versions (up to 21.02) due to kernel size restrictions. \
Upgrade via sysupgrade mechanism is not possible, so new \
installation via factory style image is required.
endef
define Device/Default
PROFILES := Default
DEVICE_DTS = kirkwood-$(lastword $(subst _, ,$(1)))
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
KERNEL := kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
KERNEL_SUFFIX := -uImage
KERNEL_IN_UBI := 1
PAGESIZE := 2048
SUBPAGESIZE := 512
BLOCKSIZE := 128k
IMAGES := sysupgrade.bin factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-ubi
endef
define Device/checkpoint_l-50
DEVICE_VENDOR := Check Point
DEVICE_MODEL := L-50
DEVICE_PACKAGES := kmod-ath9k kmod-gpio-button-hotplug kmod-mvsdio \
kmod-rtc-s35390a kmod-usb-ledtrig-usbport wpad-basic-wolfssl
IMAGES := sysupgrade.bin
endef
TARGET_DEVICES += checkpoint_l-50
define Device/cisco_on100
DEVICE_VENDOR := Cisco Systems
DEVICE_MODEL := ON100
KERNEL_SIZE := 5376k
KERNEL_IN_UBI :=
UBINIZE_OPTS := -E 5
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
DEVICE_PACKAGES := kmod-mvsdio
SUPPORTED_DEVICES += on100
endef
TARGET_DEVICES += cisco_on100
define Device/cloudengines_pogoe02
DEVICE_VENDOR := Cloud Engines
DEVICE_MODEL := Pogoplug E02
DEVICE_DTS := kirkwood-pogo_e02
SUPPORTED_DEVICES += pogo_e02
endef
TARGET_DEVICES += cloudengines_pogoe02
define Device/cloudengines_pogoplugv4
DEVICE_VENDOR := Cloud Engines
DEVICE_MODEL := Pogoplug V4
DEVICE_DTS := kirkwood-pogoplug-series-4
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 kmod-mvsdio kmod-usb3 \
kmod-gpio-button-hotplug
endef
TARGET_DEVICES += cloudengines_pogoplugv4
define Device/ctera_c200-v1
DEVICE_VENDOR := Ctera
DEVICE_MODEL := C200
DEVICE_VARIANT := V1
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-gpio-button-hotplug \
kmod-hwmon-lm63 kmod-rtc-s35390a kmod-usb-ledtrig-usbport
KERNEL := kernel-bin | append-dtb | uImage none | ctera-firmware
KERNEL_IN_UBI :=
KERNEL_SUFFIX := -factory.firm
IMAGES := sysupgrade.bin
endef
TARGET_DEVICES += ctera_c200-v1
define Device/globalscale_sheevaplug
DEVICE_VENDOR := Globalscale
DEVICE_MODEL := Sheevaplug
DEVICE_PACKAGES := kmod-mvsdio
endef
TARGET_DEVICES += globalscale_sheevaplug
define Device/iom_iconnect-1.1
DEVICE_VENDOR := Iomega
DEVICE_MODEL := Iconnect
DEVICE_DTS := kirkwood-iconnect
SUPPORTED_DEVICES += iconnect
endef
TARGET_DEVICES += iom_iconnect-1.1
define Device/iom_ix2-200
DEVICE_VENDOR := Iomega
DEVICE_MODEL := StorCenter ix2-200
DEVICE_DTS := kirkwood-iomega_ix2_200
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 \
kmod-gpio-button-hotplug kmod-hwmon-lm63
PAGESIZE := 512
SUBPAGESIZE := 256
BLOCKSIZE := 16k
KERNEL_SIZE := 3072k
KERNEL_IN_UBI :=
UBINIZE_OPTS := -E 5
IMAGE_SIZE := 31744k
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
check-size
endef
TARGET_DEVICES += iom_ix2-200
define Device/linksys
DEVICE_VENDOR := Linksys
DEVICE_PACKAGES := kmod-mwl8k wpad-basic-wolfssl kmod-gpio-button-hotplug
KERNEL_IN_UBI :=
UBINIZE_OPTS := -E 5
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
endef
define Device/linksys_e4200-v2
$(Device/linksys)
$(Device/kernel-size-migration)
DEVICE_MODEL := E4200
DEVICE_VARIANT := v2
KERNEL_SIZE := 3072k
SUPPORTED_DEVICES += linksys,viper linksys-viper
endef
TARGET_DEVICES += linksys_e4200-v2
define Device/linksys_ea3500
$(Device/linksys)
$(Device/kernel-size-migration)
DEVICE_MODEL := EA3500
PAGESIZE := 512
SUBPAGESIZE := 256
BLOCKSIZE := 16k
KERNEL_SIZE := 3072k
SUPPORTED_DEVICES += linksys,audi linksys-audi
endef
TARGET_DEVICES += linksys_ea3500
define Device/linksys_ea4500
$(Device/linksys)
$(Device/kernel-size-migration)
DEVICE_MODEL := EA4500
KERNEL_SIZE := 3072k
SUPPORTED_DEVICES += linksys,viper linksys-viper
endef
TARGET_DEVICES += linksys_ea4500
define Device/netgear_readynas-duo-v2
DEVICE_VENDOR := NETGEAR
DEVICE_MODEL := ReadyNAS Duo
DEVICE_VARIANT := v2
DEVICE_DTS := kirkwood-netgear_readynas_duo_v2
KERNEL_IN_UBI :=
IMAGES := sysupgrade.bin
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 \
kmod-gpio-button-hotplug kmod-hwmon-g762 kmod-rtc-rs5c372a kmod-usb3
endef
TARGET_DEVICES += netgear_readynas-duo-v2
define Device/raidsonic_ib-nas62x0
DEVICE_VENDOR := RaidSonic
DEVICE_MODEL := ICY BOX IB-NAS62x0
DEVICE_DTS := kirkwood-ib62x0
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4
SUPPORTED_DEVICES += ib62x0
endef
TARGET_DEVICES += raidsonic_ib-nas62x0
define Device/seagate_blackarmor-nas220
DEVICE_VENDOR := Seagate
DEVICE_MODEL := Blackarmor NAS220
DEVICE_PACKAGES := kmod-hwmon-adt7475 kmod-fs-ext4 kmod-ata-marvell-sata \
mdadm kmod-gpio-button-hotplug
PAGESIZE := 512
SUBPAGESIZE := 256
BLOCKSIZE := 16k
UBINIZE_OPTS := -e 1
endef
TARGET_DEVICES += seagate_blackarmor-nas220
define Device/seagate_dockstar
DEVICE_VENDOR := Seagate
DEVICE_MODEL := FreeAgent Dockstar
SUPPORTED_DEVICES += dockstar
endef
TARGET_DEVICES += seagate_dockstar
define Device/seagate_goflexnet
DEVICE_VENDOR := Seagate
DEVICE_MODEL := GoFlexNet
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4
SUPPORTED_DEVICES += goflexnet
endef
TARGET_DEVICES += seagate_goflexnet
define Device/seagate_goflexhome
DEVICE_VENDOR := Seagate
DEVICE_MODEL := GoFlexHome
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4
SUPPORTED_DEVICES += goflexhome
endef
TARGET_DEVICES += seagate_goflexhome
define Device/zyxel_nsa310b
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := NSA310b
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-r8169 kmod-fs-ext4 \
kmod-gpio-button-hotplug kmod-hwmon-lm85
SUPPORTED_DEVICES += nsa310b
endef
TARGET_DEVICES += zyxel_nsa310b
define Device/zyxel_nsa310s
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := NSA310S
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 kmod-gpio-button-hotplug
endef
TARGET_DEVICES += zyxel_nsa310s
define Device/zyxel_nsa325
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := NSA325
DEVICE_VARIANT := v1/v2
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 \
kmod-gpio-button-hotplug kmod-rtc-pcf8563 kmod-usb3
SUPPORTED_DEVICES += nsa325
endef
TARGET_DEVICES += zyxel_nsa325
$(eval $(call BuildImage))
Reference in New Issue View Git Blame Copy Permalink