openwrt/target/linux/ramips
Robinson Wu 84cb0f7ace ramips: add support for JS76x8 series DEV boards
This commit adds support for the Jotale JS76x8 series development boards.
These devices have the following specifications:

- SOC: MT7628AN/NN, MT7688AN, MT7628DAN
- RAM of MT7628AN/NN and MT7688AN: 64/128/256 MB (DDR2)
- RAM of MT7628DAN: 64 MB (DDR2)
- FLASH:8/16/32 MB (SPI NOR)
- Ethernet:3x 10/100 Mbps ethernet ports (MT76x8 built-in switch)
- WIFI:1x 2T2R 2.4 GHz Wi-Fi
- LEDs:1x system status green LED, 1x wifi green LED,
       3x ethernet green LED
- Buttons:1x reset button
- 1x microSD slot
- 4x USB 2.0 port
- 1x mini-usb debug UART
- 1x DC jack for main power (DC 5V)
- 1x TTL/RS232 UART
- 1x TTL/RS485 UART
- 13x GPIO header
- 1x audio codec(wm8960)

Installation via OpenWrt:

The original firmware is OpenWrt, so both LuCI and sysupgrade can be used.

Installation via U-boot web:

1. Power on board with reset button pressed, release it
   after wifi led start blinking.
2. Setup static IP 192.168.1.123/4 on your PC.
3. Go to 192.168.1.8 in browser and upload "sysupgrade" image.

Installation via U-boot tftp:
1. Connect to serial console at the mini usb, which has been connected to UART0
   on board (115200 8N1)
2. Setup static IP 192.168.1.123/4 on your PC.
3. Place openwrt-firmware.bin on your PC tftp server (192.168.1.123).
3. Connect one of LAN ports on board to your PC.
4. Start terminal software (e.g. screen /dev/ttyUSB0 115200) on PC.
5. Apply power to board.
6. Interrupt U-boot with keypress of "2".
7. At u-boot prompts:
   Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y
   Input device IP (192.168.1.8) ==:192.168.1.8
   Input server IP (192.168.1.123) ==:192.168.1.123
   Input Linux Kernel filename (root_uImage) ==:openwrt-firmware.bin
8. board will download file from tftp server, write it to flash and reboot.

Signed-off-by: Robinson Wu <wurobinson@qq.com>
[add license to DTS files, fix state_default and reduce to the mimimum,
move phy0tpt trigger to DTS, drop ucidef_set_led_timer, fix network ports]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
..
base-files/etc treewide: drop shebang from non-executable target files 2020-06-16 14:26:33 +02:00
dts ramips: add support for JS76x8 series DEV boards 2020-07-31 11:40:15 +02:00
files/drivers ramips: add arl_table support for MT7530 2020-07-17 11:00:33 +02:00
image ramips: add support for JS76x8 series DEV boards 2020-07-31 11:40:15 +02:00
mt76x8 ramips: add support for JS76x8 series DEV boards 2020-07-31 11:40:15 +02:00
mt7620 ramips: switch MT7620 subtarget to 5.4 2020-07-22 17:20:38 +02:00
mt7621 ramips: add support for D-Link DIR-1960 A1 2020-07-27 12:37:07 +02:00
patches-4.14 kernel: Update kernel 4.14 to version 4.14.187 2020-07-04 21:12:42 +02:00
patches-5.4 kernel: bump 5.4 to 5.4.52 2020-07-17 11:00:33 +02:00
rt288x ramips: remove default switch setup in 02_network 2020-05-19 19:03:02 +08:00
rt305x ramips: improve LED support for D-Link DIR-615 D series 2020-07-21 11:59:17 +02:00
rt3883 treewide: drop shebang from non-executable target files 2020-06-16 14:26:33 +02:00
Makefile ramips: add 5.4 as testing kernel 2020-04-12 22:27:18 +08:00
modules.mk ramips: fix path for dma-ralink and mtk-hsdma 2020-04-05 18:16:17 +08:00