mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-27 17:18:59 +00:00
3a4b751110
The uart node is enabled on all devices except one (GL-USB150 *). Thus, let's not have a few hundred nodes to enable it, but do not disable it in the first place. Where the majority of devices is using it, also move the serial0 alias to the DTSI. *) Since GL-USB150 even defines serial0 alias, the missing uart is probably just a mistake. Anyway, disable it for now so this patch stays cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
103 lines
1.6 KiB
Plaintext
103 lines
1.6 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "ar9341.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
aliases {
|
|
led-boot = &led_power;
|
|
led-failsafe = &led_power;
|
|
led-running = &led_power;
|
|
led-upgrade = &led_power;
|
|
label-mac-device = &wmac;
|
|
};
|
|
|
|
leds: leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_power: power {
|
|
label = "green:power";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
wlan {
|
|
label = "green:wlan";
|
|
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
qss {
|
|
label = "green:qss";
|
|
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wan {
|
|
label = "green:wan";
|
|
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
lan1 {
|
|
label = "green:lan1";
|
|
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
lan2 {
|
|
label = "green:lan2";
|
|
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
lan3 {
|
|
label = "green:lan3";
|
|
gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
lan4 {
|
|
label = "green:lan4";
|
|
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&ref {
|
|
clock-frequency = <25000000>;
|
|
};
|
|
|
|
&gpio {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&jtag_disable_pins &pmx_usb_power>;
|
|
};
|
|
|
|
&pinmux {
|
|
pmx_usb_power: usb_power {
|
|
pinctrl-single,bits = <0x4 0x0 0xff>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&swphy0>;
|
|
|
|
mtd-mac-address = <&uboot 0x1fc00>;
|
|
mtd-mac-address-increment = <(-1)>;
|
|
};
|
|
|
|
ð1 {
|
|
mtd-mac-address = <&uboot 0x1fc00>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
switch-phy-swap = <1>;
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&uboot 0x1fc00>;
|
|
};
|