mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-20 06:08:08 +00:00
dd8a4a8c34
This patch adds supports for GL-X1200.
Specification:
- SOC: QCA9563 (775MHz)
- Flash: 16 MiB
- RAM: 128 MiB DDR2
- Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless: QCA9563(2.4GHz) and QCA9886(5GHz)
- SIM: 2x SIM card slots
- MicroSD: 1x microSD slot
- Antenna: 2x external 5dBi antennas
- USB: 1x USB 2.0 port
- Button: 1x reset button
- LED: 16x LEDs (3x GPIO controllable)
- UART: 1x UART on PCB (JP1: 3.3V, RX, TX, GND)
- OEM U-Boot supplies HTTP/GUI access
Implementation Notes
====================
Both the NOR and NAND variants boot off a NOR-based kernel,
consistent with the OEM's firmware.
The mode LEDs are
* Boot, Running system
* Failsafe 2G
* Upgrade 5G
Installation
============
Using sysupgrade
----------------
sysupgrade may be used to install a NAND image on a device running
a NAND image or a NOR image on a device running a NOR image. It is
recommended to *not* preserve config when upgrading from OEM firmware
or previous versions of OpenWrt. No supported sysupgrade path should
require "force". Transitioning from NOR to NAND can be accomplished
Using U-Boot
------------
The OEM U-Boot can be put into a graphical, firmware-upload mode by
holding down the button on the side of the router while applying power
and for a bit more than five seconds following with the current OEM
U-Boot. The power LED will come on, then the 5G LED will flash five
times, about once a second. When the 5G LED stops flashing and the
2G LED lights solid, the router's U-Boot will provide an upload page
at http://192.168.1.1/ Either a browser may be used to upload an image,
or a utility such as curl may be used:
curl -X POST -F gl_firmware=\@*-nand-squashfs-factory.img \
http://192.168.1.1/index.html
or
curl -X POST -F gl_firmware=\@*-nor-squashfs-sysupgrade.bin \
http://192.168.1.1/index.html
Note that NOR vs. NAND is based on the file name extension.
Signed-off-by: Xinfa Deng <xinfa.deng@gl-inet.com>
449 lines
12 KiB
Makefile
449 lines
12 KiB
Makefile
define Build/dongwon-header
|
|
head -c 4 $@ > $@.tmp
|
|
head -c 8 /dev/zero >> $@.tmp
|
|
tail -c +9 $@ >> $@.tmp
|
|
( \
|
|
header_crc="$$(head -c 68 $@.tmp | gzip -c | \
|
|
tail -c 8 | od -An -N4 -tx4 --endian little | tr -d ' \n')"; \
|
|
printf "$$(echo $$header_crc | sed 's/../\\x&/g')" | \
|
|
dd of=$@.tmp bs=4 count=1 seek=1 conv=notrunc \
|
|
)
|
|
mv $@.tmp $@
|
|
endef
|
|
|
|
# attention: only zlib compression is allowed for the boot fs
|
|
define Build/zyxel-buildkerneljffs
|
|
mkdir -p $@.tmp/boot
|
|
cp $@ $@.tmp/boot/vmlinux.lzma.uImage
|
|
$(STAGING_DIR_HOST)/bin/mkfs.jffs2 \
|
|
--big-endian --squash-uids -v -e 128KiB -q -f -n -x lzma -x rtime \
|
|
-o $@ \
|
|
-d $@.tmp
|
|
rm -rf $@.tmp
|
|
endef
|
|
|
|
define Build/zyxel-factory
|
|
let \
|
|
maxsize="$(subst k,* 1024,$(RAS_ROOTFS_SIZE))"; \
|
|
let size="$$(stat -c%s $@)"; \
|
|
if [ $$size -lt $$maxsize ]; then \
|
|
$(STAGING_DIR_HOST)/bin/mkrasimage \
|
|
-b $(RAS_BOARD) \
|
|
-v $(RAS_VERSION) \
|
|
-r $@ \
|
|
-s $$maxsize \
|
|
-o $@.new \
|
|
-l 131072 \
|
|
&& mv $@.new $@ ; \
|
|
fi
|
|
endef
|
|
|
|
define Device/8dev_rambutan
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := 8devices
|
|
DEVICE_MODEL := Rambutan
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
KERNEL_IN_UBI := 1
|
|
IMAGES := factory.bin sysupgrade.tar
|
|
IMAGE/sysupgrade.tar := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-ubi
|
|
endef
|
|
TARGET_DEVICES += 8dev_rambutan
|
|
|
|
define Device/aerohive_hiveap-121
|
|
SOC := ar9344
|
|
DEVICE_VENDOR := Aerohive
|
|
DEVICE_MODEL := HiveAP 121
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
IMAGE_SIZE := 116m
|
|
KERNEL_SIZE := 5120k
|
|
UBINIZE_OPTS := -E 5
|
|
SUPPORTED_DEVICES += hiveap-121
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += aerohive_hiveap-121
|
|
|
|
define Device/domywifi_dw33d
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := DomyWifi
|
|
DEVICE_MODEL := DW33D
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-storage kmod-usb-ledtrig-usbport \
|
|
kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
KERNEL_SIZE := 5120k
|
|
IMAGE_SIZE := 98304k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
endef
|
|
TARGET_DEVICES += domywifi_dw33d
|
|
|
|
define Device/dongwon_dw02-412h
|
|
SOC := qca9557
|
|
DEVICE_VENDOR := Dongwon T&I
|
|
DEVICE_MODEL := DW02-412H
|
|
DEVICE_ALT0_VENDOR := KT
|
|
DEVICE_ALT0_MODEL := GiGA WiFi home
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
KERNEL_SIZE := 8192k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL := $$(KERNEL) | dongwon-header
|
|
KERNEL_INITRAMFS := $$(KERNEL)
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES += factory.img
|
|
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
|
|
define Device/dongwon_dw02-412h-64m
|
|
$(Device/dongwon_dw02-412h)
|
|
DEVICE_VARIANT := (64M)
|
|
DEVICE_ALT0_VARIANT := (64M)
|
|
IMAGE_SIZE := 49152k
|
|
endef
|
|
TARGET_DEVICES += dongwon_dw02-412h-64m
|
|
|
|
define Device/dongwon_dw02-412h-128m
|
|
$(Device/dongwon_dw02-412h)
|
|
DEVICE_VARIANT := (128M)
|
|
DEVICE_ALT0_VARIANT := (128M)
|
|
IMAGE_SIZE := 114688k
|
|
endef
|
|
TARGET_DEVICES += dongwon_dw02-412h-128m
|
|
|
|
define Device/glinet_gl-ar300m-common-nand
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-AR300M
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 16000k
|
|
PAGESIZE := 2048
|
|
VID_HDR_OFFSET := 2048
|
|
endef
|
|
|
|
define Device/glinet_gl-ar300m-nand
|
|
$(Device/glinet_gl-ar300m-common-nand)
|
|
DEVICE_VARIANT := NAND
|
|
BLOCKSIZE := 128k
|
|
IMAGES += factory.img
|
|
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
SUPPORTED_DEVICES += glinet,gl-ar300m-nor
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-ar300m-nand
|
|
|
|
define Device/glinet_gl-ar300m-nor
|
|
$(Device/glinet_gl-ar300m-common-nand)
|
|
DEVICE_VARIANT := NOR
|
|
SUPPORTED_DEVICES += glinet,gl-ar300m-nand gl-ar300m
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-ar300m-nor
|
|
|
|
define Device/glinet_gl-ar750s-common
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-AR750S
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct kmod-usb2 \
|
|
kmod-usb-storage block-mount
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
|
|
define Device/glinet_gl-ar750s-nor-nand
|
|
$(Device/glinet_gl-ar750s-common)
|
|
DEVICE_VARIANT := NOR/NAND
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
SUPPORTED_DEVICES += glinet,gl-ar750s-nor
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-ar750s-nor-nand
|
|
|
|
define Device/glinet_gl-ar750s-nor
|
|
$(Device/glinet_gl-ar750s-common)
|
|
DEVICE_VARIANT := NOR
|
|
SUPPORTED_DEVICES += gl-ar750s glinet,gl-ar750s glinet,gl-ar750s-nor-nand
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-ar750s-nor
|
|
|
|
define Device/glinet_gl-e750
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-E750
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct kmod-usb2
|
|
SUPPORTED_DEVICES += gl-e750
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 131072k
|
|
PAGESIZE := 2048
|
|
VID_HDR_OFFSET := 2048
|
|
BLOCKSIZE := 128k
|
|
IMAGES += factory.img
|
|
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-e750
|
|
|
|
define Device/glinet_gl-xe300
|
|
SOC := qca9531
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-XE300
|
|
DEVICE_PACKAGES := kmod-usb2 block-mount kmod-usb-serial-ch341 \
|
|
kmod-usb-net-qmi-wwan uqmi
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 131072k
|
|
PAGESIZE := 2048
|
|
VID_HDR_OFFSET := 2048
|
|
BLOCKSIZE := 128k
|
|
IMAGES += factory.img
|
|
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-xe300
|
|
|
|
define Device/glinet_gl-x1200-common
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-X1200
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct-htt kmod-usb2 \
|
|
kmod-usb-storage block-mount kmod-usb-net-qmi-wwan uqmi
|
|
IMAGE_SIZE := 16000k
|
|
endef
|
|
|
|
define Device/glinet_gl-x1200-nor-nand
|
|
$(Device/glinet_gl-x1200-common)
|
|
DEVICE_VARIANT := NOR/NAND
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 131072k
|
|
PAGESIZE := 2048
|
|
VID_HDR_OFFSET := 2048
|
|
BLOCKSIZE := 128k
|
|
IMAGES += factory.img
|
|
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-x1200-nor-nand
|
|
|
|
define Device/glinet_gl-x1200-nor
|
|
$(Device/glinet_gl-x1200-common)
|
|
DEVICE_VARIANT := NOR
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-x1200-nor
|
|
|
|
define Device/linksys_ea4500-v3
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_MODEL := EA4500
|
|
DEVICE_VARIANT := v3
|
|
DEVICE_PACKAGES := kmod-usb2
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 81920k
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
LINKSYS_HWNAME := EA4500V3
|
|
IMAGES += factory.img
|
|
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
|
|
append-ubi | check-size | linksys-image type=$$$$(LINKSYS_HWNAME)
|
|
UBINIZE_OPTS := -E 5
|
|
endef
|
|
TARGET_DEVICES += linksys_ea4500-v3
|
|
|
|
# fake rootfs is mandatory, pad-offset 64 equals (1 * uimage_header)
|
|
define Device/netgear_ath79_nand
|
|
DEVICE_VENDOR := NETGEAR
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
|
|
KERNEL_SIZE := 4096k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
IMAGE_SIZE := 25600k
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma | \
|
|
pad-offset $$(BLOCKSIZE) 64 | append-uImage-fakehdr filesystem $$(UIMAGE_MAGIC)
|
|
IMAGES := sysupgrade.bin factory.img
|
|
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
|
|
append-ubi | check-size | netgear-dni
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
UBINIZE_OPTS := -E 5
|
|
endef
|
|
|
|
define Device/netgear_pgzng1
|
|
SOC := ar9344
|
|
DEVICE_MODEL := PGZNG1
|
|
DEVICE_VENDOR := NETGEAR
|
|
DEVICE_ALT0_MODEL := Pulse Gateway
|
|
DEVICE_ALT0_VENDOR := ADT
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-i2c-gpio \
|
|
kmod-leds-pca955x kmod-rtc-isl1208 kmod-spi-dev
|
|
KERNEL_SIZE := 5120k
|
|
IMAGE_SIZE := 83968k
|
|
PAGESIZE := 2048
|
|
BLOCKSIZE := 128k
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
TARGET_DEVICES += netgear_pgzng1
|
|
|
|
define Device/netgear_r6100
|
|
SOC := ar9344
|
|
DEVICE_MODEL := R6100
|
|
UIMAGE_MAGIC := 0x36303030
|
|
NETGEAR_BOARD_ID := R6100
|
|
NETGEAR_HW_ID := 29764434+0+128+128+2x2+2x2
|
|
$(Device/netgear_ath79_nand)
|
|
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
endef
|
|
TARGET_DEVICES += netgear_r6100
|
|
|
|
define Device/netgear_wndr3700-v4
|
|
SOC := ar9344
|
|
DEVICE_MODEL := WNDR3700
|
|
DEVICE_VARIANT := v4
|
|
UIMAGE_MAGIC := 0x33373033
|
|
NETGEAR_BOARD_ID := WNDR3700v4
|
|
NETGEAR_HW_ID := 29763948+128+128
|
|
$(Device/netgear_ath79_nand)
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr3700-v4
|
|
|
|
define Device/netgear_wndr4300
|
|
SOC := ar9344
|
|
DEVICE_MODEL := WNDR4300
|
|
UIMAGE_MAGIC := 0x33373033
|
|
NETGEAR_BOARD_ID := WNDR4300
|
|
NETGEAR_HW_ID := 29763948+0+128+128+2x2+3x3
|
|
$(Device/netgear_ath79_nand)
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr4300
|
|
|
|
define Device/netgear_wndr4300sw
|
|
SOC := ar9344
|
|
DEVICE_MODEL := WNDR4300SW
|
|
UIMAGE_MAGIC := 0x33373033
|
|
NETGEAR_BOARD_ID := WNDR4300SW
|
|
NETGEAR_HW_ID := 29763948+0+128+128+2x2+3x3
|
|
$(Device/netgear_ath79_nand)
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr4300sw
|
|
|
|
define Device/netgear_wndr4300tn
|
|
SOC := ar9344
|
|
DEVICE_MODEL := WNDR4300TN
|
|
UIMAGE_MAGIC := 0x33373033
|
|
NETGEAR_BOARD_ID := WNDR4300TN
|
|
NETGEAR_HW_ID := 29763948+0+128+128+2x2+3x3
|
|
$(Device/netgear_ath79_nand)
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr4300tn
|
|
|
|
define Device/netgear_wndr4300-v2
|
|
SOC := qca9563
|
|
DEVICE_MODEL := WNDR4300
|
|
DEVICE_VARIANT := v2
|
|
UIMAGE_MAGIC := 0x27051956
|
|
NETGEAR_BOARD_ID := WNDR4500series
|
|
NETGEAR_HW_ID := 29764821+2+128+128+3x3+3x3+5508012175
|
|
$(Device/netgear_ath79_nand)
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr4300-v2
|
|
|
|
define Device/netgear_wndr4500-v3
|
|
SOC := qca9563
|
|
DEVICE_MODEL := WNDR4500
|
|
DEVICE_VARIANT := v3
|
|
UIMAGE_MAGIC := 0x27051956
|
|
NETGEAR_BOARD_ID := WNDR4500series
|
|
NETGEAR_HW_ID := 29764821+2+128+128+3x3+3x3+5508012173
|
|
$(Device/netgear_ath79_nand)
|
|
endef
|
|
TARGET_DEVICES += netgear_wndr4500-v3
|
|
|
|
define Device/zte_mf28x_common
|
|
SOC := qca9563
|
|
DEVICE_VENDOR := ZTE
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
|
|
define Device/zte_mf281
|
|
$(Device/zte_mf28x_common)
|
|
DEVICE_MODEL := MF281
|
|
KERNEL_SIZE := 6144k
|
|
IMAGE_SIZE := 29696k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
DEVICE_PACKAGES += ath10k-firmware-qca9888-ct kmod-usb-net-rndis \
|
|
kmod-usb-acm comgt-ncm
|
|
endef
|
|
TARGET_DEVICES += zte_mf281
|
|
|
|
define Device/zte_mf286
|
|
$(Device/zte_mf28x_common)
|
|
DEVICE_MODEL := MF286
|
|
DEVICE_PACKAGES += ath10k-firmware-qca988x-ct kmod-usb-net-qmi-wwan \
|
|
kmod-usb-serial-option uqmi
|
|
endef
|
|
TARGET_DEVICES += zte_mf286
|
|
|
|
define Device/zte_mf286a
|
|
$(Device/zte_mf28x_common)
|
|
DEVICE_MODEL := MF286A
|
|
DEVICE_PACKAGES += ath10k-firmware-qca9888-ct kmod-usb-net-qmi-wwan \
|
|
kmod-usb-serial-option uqmi
|
|
endef
|
|
TARGET_DEVICES += zte_mf286a
|
|
|
|
define Device/zte_mf286r
|
|
$(Device/zte_mf28x_common)
|
|
DEVICE_MODEL := MF286R
|
|
DEVICE_PACKAGES += ath10k-firmware-qca9888-ct kmod-usb-net-rndis kmod-usb-acm \
|
|
comgt-ncm
|
|
endef
|
|
TARGET_DEVICES += zte_mf286r
|
|
|
|
define Device/zyxel_nbg6716
|
|
SOC := qca9558
|
|
DEVICE_VENDOR := ZyXEL
|
|
DEVICE_MODEL := NBG6716
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-ath10k-ct \
|
|
ath10k-firmware-qca988x-ct
|
|
RAS_BOARD := NBG6716
|
|
RAS_ROOTFS_SIZE := 29696k
|
|
RAS_VERSION := "OpenWrt Linux-$(LINUX_VERSION)"
|
|
KERNEL_SIZE := 4096k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
LOADER_TYPE := bin
|
|
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel | uImage none | \
|
|
zyxel-buildkerneljffs | check-size 4096k
|
|
IMAGES := sysupgrade.tar sysupgrade-4M-Kernel.bin factory.bin
|
|
IMAGE/sysupgrade.tar/squashfs := append-rootfs | pad-to $$$$(BLOCKSIZE) | \
|
|
sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
IMAGE/sysupgrade-4M-Kernel.bin/squashfs := append-kernel | \
|
|
pad-to $$$$(KERNEL_SIZE) | append-ubi | pad-to 263192576 | gzip
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
|
|
zyxel-factory
|
|
UBINIZE_OPTS := -E 5
|
|
endef
|
|
TARGET_DEVICES += zyxel_nbg6716
|
|
|
|
define Device/zyxel_emg2926_q10a
|
|
$(Device/zyxel_nbg6716)
|
|
DEVICE_MODEL := EMG2926-Q10A
|
|
RAS_BOARD := AAVK-EMG2926Q10A
|
|
endef
|
|
TARGET_DEVICES += zyxel_emg2926_q10a
|