mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-28 17:48:58 +00:00
635d5488c9
Specifications:
SOC: QCA9563 775 MHz + QCA9880
Switch: QCA8337N-AL3C
RAM: Winbond W9751G6KB-25 64 MiB
Flash: Winbond W25Q128FVSG 16 MiB
WLAN: Wi-Fi4 2.4 GHz 3*3 + 5 GHz 3*3
LAN: LAN ports *4
WAN: WAN port *1
Buttons: reset *1 + wps *1
LEDs: ethernet *5, power, wlan, wps
MAC Address:
use address source1 source2
label 40:9b:xx:xx:xx:3c lan && wlan u-boot,env@ethaddr
lan 40:9b:xx:xx:xx:3c devdata@0x3f $label
wan 40:9b:xx:xx:xx:3f devdata@0x8f $label + 3
wlan2g 40:9b:xx:xx:xx:3c devdata@0x5b $label
wlan5g 40:9b:xx:xx:xx:3e devdata@0x76 $label + 2
Install via Web UI:
Apply factory image in the stock firmware's Web UI.
Install via Emergency Room Mode:
DIR-859 A1 will enter recovery mode when the system fails to boot
or press reset button for about 10 seconds.
First, set computer IP to 192.168.0.5 and Gateway to 192.168.0.1.
Then we can open http://192.168.0.1 in the web browser to upload
OpenWrt factory image or stock firmware. Some modern browsers may
need to turn on compatibility mode.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 0ffbef9317)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
153 lines
2.7 KiB
Plaintext
153 lines
2.7 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca956x.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
wps {
|
|
label = "wps";
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
|
|
ath10k: wifi@0,0 {
|
|
compatible = "qcom,ath10k";
|
|
reg = <0x0000 0 0 0 0>;
|
|
|
|
nvmem-cells = <&calibration_ath10k>, <&macaddr_devdata_94>;
|
|
nvmem-cell-names = "calibration", "mac-address-ascii";
|
|
};
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "bootloader";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
bdcfg: partition@40000 {
|
|
compatible = "u-boot,env";
|
|
label = "bdcfg";
|
|
reg = <0x040000 0x010000>;
|
|
};
|
|
|
|
partition@50000 {
|
|
label = "devdata";
|
|
reg = <0x050000 0x010000>;
|
|
read-only;
|
|
|
|
compatible = "nvmem-cells";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
macaddr_devdata_94: macaddr@94 {
|
|
reg = <0x94 0x11>;
|
|
};
|
|
|
|
macaddr_devdata_b0: macaddr@b0 {
|
|
reg = <0xb0 0x11>;
|
|
};
|
|
};
|
|
|
|
partition@60000 {
|
|
label = "devconf";
|
|
reg = <0x060000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@70000 {
|
|
compatible = "seama";
|
|
label = "firmware";
|
|
reg = <0x070000 0xf80000>;
|
|
};
|
|
|
|
partition@ff0000 {
|
|
label = "art";
|
|
reg = <0xff0000 0x010000>;
|
|
read-only;
|
|
|
|
compatible = "nvmem-cells";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
calibration_ath9k: calibration@1000 {
|
|
reg = <0x1000 0x440>;
|
|
};
|
|
|
|
calibration_ath10k: calibration@5000 {
|
|
reg = <0x5000 0x844>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
phy-mode = "sgmii";
|
|
qca,mib-poll-interval = <500>;
|
|
|
|
reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
|
|
qca,ar8327-initvals = <
|
|
0x04 0x00080080 /* PORT0 PAD MODE CTRL */
|
|
0x10 0x81000080 /* POWER_ON_STRAP */
|
|
0x50 0xcc35cc35 /* LED_CTRL0 */
|
|
0x54 0xcb37cb37 /* LED_CTRL1 */
|
|
0x58 0x00000000 /* LED_CTRL2 */
|
|
0x5c 0x00f3cf00 /* LED_CTRL3 */
|
|
0x7c 0x0000007e /* PORT0_STATUS */
|
|
>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
pll-data = <0x03000101 0x00000101 0x00001919>;
|
|
|
|
phy-mode = "sgmii";
|
|
phy-handle = <&phy0>;
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
nvmem-cells = <&calibration_ath9k>, <&macaddr_devdata_b0>;
|
|
nvmem-cell-names = "calibration", "mac-address-ascii";
|
|
};
|