mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-23 07:22:33 +00:00
09f313bfd7
The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access point distributed as Experia WiFi by KPN in the Netherlands. It features two ethernet ports and 2 internal antennas. Specifications -------------- SOC : Mediatek MT7621AT ETH : Two 1 gigabit ports, built into the SOC WIFI : MT7615DN BUTTON: Reset BUTTON: WPS LED : Power (green+red) LED : WiFi (green+blue) LED : WPS (green+red) LED : Followme (green+red) Power : 12 VDC, 1A barrel plug Winbond variant: RAM : Winbond W631GG6MB12J, 1GBIT DDR3 SDRAM Flash : Winbond W25Q256JVFQ, 256Mb SPI U-Boot: 1.1.3 (Nov 23 2017 - 16:40:17), Ralink 5.0.0.1 Macronix variant: RAM : Nanya NT5CC64M16GP-DI, 1GBIT DDR3 SDRAM Flash : MX25l25635FMI-10G, 256Mb SPI U-Boot: 1.1.3 (Dec 4 2017 - 11:37:57), Ralink 5.0.0.1 Serial ------ The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 57600-8-N-1. The board has an unpopulated 2.54mm straight pin header. The pinout is: VCC (the square), RX, TX, GND. Installation ------------ See the Wiki page [1] for more details, it comes down to: 1. Open the device, take off the heat sink 2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. Also connect the RESET pin for stability (thanks @FPSUsername for reporting) 3. Make a backup in case you want to revert to stock later 4. Flash the squashfs-factory.trx file to offset 0x50000 of the flash 5. Ensure the bootpartition variable is set to 0 in the U-Boot environment located at 0x30000 Note that the U-Boot is password protected, this can optionally be removed. See the forum [2] for more details. MAC Addresses(stock) -------------------- +----------+------------------+-------------------+ | use | address | example | +----------+------------------+-------------------+ | Device | label | 00:00:00:11:00:00 | | Ethernet | + 3 | 00:00:00:11:00:03 | | 2g | + 0x020000f00001 | 02:00:00:01:00:01 | | 5g | + 1 | 00:00:00:11:00:01 | +----------+------------------+-------------------+ The label address is stored in ASCII in the board_data partition Notes ----- - This device has a dual-boot partition scheme, but OpenWRT will claim both partitions for more storage space. Known issues ------------ - 2g MAC address does not match stock due to missing support for that in macaddr_add - Only the power LED is configured by default References ---------- [1] https://openwrt.org/inbox/toh/arcadyan/astoria/we420223-99 [2] https://forum.openwrt.org/t/adding-openwrt-support-for-arcadyan-we420223-99-kpn-experia-wifi/132653 Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: Harm Berntsen <git@harmberntsen.nl>
130 lines
3.1 KiB
Plaintext
130 lines
3.1 KiB
Plaintext
#
|
|
# Copyright (C) 2011-2012 OpenWrt.org
|
|
#
|
|
|
|
[ -e /etc/config/ubootenv ] && exit 0
|
|
|
|
touch /etc/config/ubootenv
|
|
|
|
. /lib/uboot-envtools.sh
|
|
. /lib/functions.sh
|
|
|
|
board=$(board_name)
|
|
|
|
case "$board" in
|
|
alfa-network,ac1200rm|\
|
|
alfa-network,awusfree1|\
|
|
alfa-network,quad-e4g|\
|
|
alfa-network,r36m-e4g|\
|
|
alfa-network,tube-e4g|\
|
|
engenius,esr600h|\
|
|
sitecom,wlr-4100-v1-002)
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x1000" "0x1000"
|
|
;;
|
|
arcadyan,we420223-99)
|
|
ubootenv_add_uci_config "/dev/mtd2" "0x0" "0x1000" "0x1000"
|
|
;;
|
|
allnet,all0256n-4m|\
|
|
allnet,all0256n-8m|\
|
|
allnet,all5002|\
|
|
yuncore,ax820)
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x10000" "0x10000"
|
|
;;
|
|
ampedwireless,ally-00x19k|\
|
|
ampedwireless,ally-r1900k)
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x1000" "0x20000" "4"
|
|
;;
|
|
beeline,smartbox-giga|\
|
|
beeline,smartbox-turbo|\
|
|
etisalat,s3|\
|
|
rostelecom,rt-sf-1)
|
|
ubootenv_add_uci_config "/dev/mtd0" "0x80000" "0x1000" "0x20000"
|
|
;;
|
|
buffalo,wsr-1166dhp|\
|
|
buffalo,wsr-600dhp|\
|
|
kroks,kndrt31r16|\
|
|
kroks,kndrt31r19|\
|
|
mediatek,linkit-smart-7688|\
|
|
samknows,whitebox-v8|\
|
|
xiaomi,mi-router-4c|\
|
|
xiaomi,miwifi-nano|\
|
|
zbtlink,zbt-wg2626|\
|
|
zte,mf283plus)
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x1000" "0x10000"
|
|
;;
|
|
asus,rt-ax53u|\
|
|
belkin,rt1800|\
|
|
h3c,tx1800-plus|\
|
|
h3c,tx1801-plus|\
|
|
h3c,tx1806|\
|
|
jcg,q20|\
|
|
linksys,e7350|\
|
|
netgear,wax202)
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000"
|
|
;;
|
|
haier,har-20s2u1|\
|
|
sim,simax1800t)
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000"
|
|
ubootenv_add_uci_sys_config "/dev/mtd1" "0x40000" "0x40000" "0x20000"
|
|
;;
|
|
hootoo,ht-tm05|\
|
|
ravpower,rp-wd03)
|
|
idx="$(find_mtd_index u-boot-env)"
|
|
[ -n "$idx" ] && \
|
|
ubootenv_add_uci_config "/dev/mtd$idx" "0x4000" "0x1000" "0x1000"
|
|
;;
|
|
beeline,smartbox-flash|\
|
|
linksys,ea6350-v4|\
|
|
linksys,ea7300-v1|\
|
|
linksys,ea7300-v2|\
|
|
linksys,ea7500-v2|\
|
|
linksys,ea8100-v1|\
|
|
linksys,ea8100-v2|\
|
|
mts,wg430223)
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x1000" "0x20000"
|
|
;;
|
|
snr,cpe-w4n-mt)
|
|
idx="$(find_mtd_index uboot-env)"
|
|
[ -n "$idx" ] && \
|
|
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x1000" "0x1000"
|
|
;;
|
|
tplink,ec330-g5u-v1)
|
|
idx="$(find_mtd_index u-boot-env)"
|
|
[ -n "$idx" ] && \
|
|
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x1000" "0x20000"
|
|
;;
|
|
xiaomi,mi-router-3g-v2|\
|
|
xiaomi,mi-router-4a-gigabit|\
|
|
xiaomi,miwifi-3c)
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x1000" "0x10000"
|
|
ubootenv_add_uci_sys_config "/dev/mtd2" "0x0" "0x4000" "0x10000"
|
|
;;
|
|
xiaomi,mi-router-3g|\
|
|
xiaomi,mi-router-3-pro|\
|
|
xiaomi,mi-router-4|\
|
|
xiaomi,mi-router-ac2100|\
|
|
xiaomi,redmi-router-ac2100)
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x1000" "0x20000"
|
|
ubootenv_add_uci_sys_config "/dev/mtd2" "0x0" "0x4000" "0x20000"
|
|
;;
|
|
zyxel,lte3301-plus)
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x1000" "0x80000"
|
|
;;
|
|
zyxel,nr7101)
|
|
idx="$(find_mtd_index Config)"
|
|
[ -n "$idx" ] && \
|
|
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x1000" "0x80000"
|
|
;;
|
|
bolt,arion|\
|
|
xiaomi,mi-router-cr6606|\
|
|
xiaomi,mi-router-cr6608|\
|
|
xiaomi,mi-router-cr6609)
|
|
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x10000" "0x20000"
|
|
;;
|
|
esac
|
|
|
|
config_load ubootenv
|
|
config_foreach ubootenv_add_app_config
|
|
|
|
exit 0
|