NVMEM is the upstream replacement for this. ralink,mtd-eeprom is
deprecated. The others need to stay as there's byte swapping going on.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16084
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support this boards to envtools config
This commit integrates the latest changes from new U-Boot, which includes important updates to the DTSI files for the Orange Pi R1 Plus and Orange Pi R1 Plus LTS boards.
Signed-off-by: Vyacheslav Ivanov <islavaivanov76@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16090
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop config and files for Linux 6.1.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16107
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch to Linux kernel version 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16107
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use ath10k-ct 6.9 to better match mac80211 backports 6.9.x
Drop patch 010 that is merged upstream.
Add patch 001 to fix version to 6.9 (overlooked by upstream).
Refresh patches.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/16036
Signed-off-by: Robert Marko <robimarko@gmail.com>
Also migrate mt7623 to new fitblk support scripts which simplify
sysupgrade when using uImage.FIT. This had been forgotten previously.
Fixes: 4448d6325f ("mediatek: make use of common uImage.FIT upgrade functions")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The function fitblk_get_bootdev doesn't exist any more, using it in
export_bootdevice anyway never made much sense and only worked for
classic block devices.
Just drop /dev/fit* handling there, it isn't needed anywhere.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Simplifies the code by removing clk_disable_unprepare.
Also removed gotos and used dev_err_probe.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16133
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix a use-after-free bug in mtk_wed_setup_tc_block_cb()
which leads to kernel panic when setup multiple ap
interfaces on one band of mt798x.
Signed-off-by: Zheng Zhang <everything411@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16118
Signed-off-by: Robert Marko <robimarko@gmail.com>
Read the 'fip' static volume in order to trigger scrubbing in case of
detecting flipped bits while reading.
We have to do this in Linux because we never read or touch the 'fip'
volume and the UBISPL implementation in ARM TrustedFirmware-A does NOT
handle scrubbing itself.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reporting an unclean read from SPI-NAND only when the maximum number
of correctable bitflip errors has been hit seems a bit late.
UBI LEB scrubbing, which depends on the lower MTD device reporting
correctable bitflips, then only kicks in when it's almost too late.
Set bitflip_threshold to 75% of the ECC strength, which is also the
default for raw NAND.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A bug has plagued bl2 which caused failure to boot and bricked Linksys
E8450 and Belkin RT3200 devices in case of correctable bitflips being
detected during a read operation. A simple logic error resulted in read
to be considered errornous instead of just continueing in case of
correctable bitflips.
Address this by importing a patch fixing that logic error.
The issue, which has been dubbed as the "OpenWrt Kiss of Death", and is
now a thing of the past.
Users should preemptively update bl2 to prevent their devices being at
risk.
Link: https://github.com/mtk-openwrt/arm-trusted-firmware/pull/11
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It seems that some Xiaomi AX3000T boards changed to using Winbond W25N01KV
SPI-NAND which is not supported in OpenWrt nor upstream kernel.
So, add a pending patch to support it as upstream supports rest of the KV
revision models.
Fixes: #16002
Link: https://github.com/openwrt/openwrt/pull/16088
Signed-off-by: Robert Marko <robimarko@gmail.com>
We need to configure the led and network config for this board on
start as per the others
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15607
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add patches for the nanopi r6s board, backporting from 6.9 where
basic support is landing.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15607
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backporting support for the NanoPi R6S from upstream
uboot.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15607
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Upstream uboot have merged in kernel dts files, we need
the update for the rk3588 boards.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15607
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adding support for the rk3588 platform
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15607
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of enabling RSS support, let's introduce a variant and let users
choose between both variants since it can cause network issues.
Signed-off-by: Milinda Brantini <C_A_T_T_E_R_Y@outlook.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Instead of enabling RSS support, let's introduce a variant and let users
choose between both variants since it can cause network issues.
Signed-off-by: Milinda Brantini <C_A_T_T_E_R_Y@outlook.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The keys are created differently compared to the old OPKG keys. Instead
of being part of base-files/configure, they are created as a Makefile
requirement of `package/compile`, which is a cleaner solution.
This requirement would only be added to non SDK environments, however
APK always requires keys to be available. Add an `else` case for the SDK
and create keys.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Cambium Networks XE3-4 is a tri-radio Wi-Fi 6/6E 4×4/2×2 AP.
Hardware:
Model: Cambium Networks XE3-4
CPU: IPQ6010/AP-CP01-C3, SoC Version: 1.0 @ 800 MHz
Memory: 1 GiB
Flash: 512 MiB Macronix MX30UF2G18AC + W25Q128FW
Ethernet: 1x 1 GbE (QCA8072)
1x 2.5 GbE (QCA8081)
Buttons: 1x Reset
Serial: TX, RX, GND
Baudrate: 115200
Radios: Qualcomm Atheros IPQ6018 802.11ax - 2x2 - 2GHz
Qualcomm Atheros IPQ6018 802.11ax - 2x2 - 5GHz
Qualcomm Atheros QCN9074 802.11ax - 4x4 - 5GHz or 6GHz
BLE 4.1
Power: 32.0W 802.3bt5 PoE++
25.5W 802.3at with USB, BT disabled
Size: 215mm x 215mm
Ports: 1x USB 2.0
Antenna: 6 GHz: 6.29 dBi, Omni 30 dBm
5 GHz: 6.12 dBi, Omni 31 dBm
2.4 GHz: 4.85 dBi, Omni 29 dBm
LEDs: Multi-color status LEDs
Mounting: Wall, ceiling or T-bar
Installation: Serial connection
1. Open the AP to get access to the board. Connect RX, TX and GND.
2. Power on the AP, and short the CS pin of the SPI flash with
one of the APs GND pins.
3. Transfer the initramfs image with TFTP
(Default server IP is 192.168.0.120)
# tftpboot factory.ubi
4. Flash the rootfs partition
# flash rootfs
5. Reboot the AP
# reset
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15633
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fixes the image check failed on system upgrade
"Image check failed:
upgrade: Device radxa,rock3a not supported by this image
upgrade: Supported devices: radxa,rock-3a"
Signed-off-by: Tomas Lara <tl849670@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16064
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
According to RTL8221B's datasheet, the PHY requires at least 10ms
for assert and 68ms (recommended) for de-assert. So increase the
assert/de-assert time to 15ms and 68ms respectively.
Fixes: c0c3234e17 ("mediatek: add support for JDCloud RE-CP-03")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16106
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Refactor Inteno XG6846 device tree to be in line with other bmips devices.
Also expose USB LED automatically.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
- Enable CONFIG_HWMON and CONFIG_THERMAL_HWMON on all subtargets.
- Drop kmod-thermal from bcm2712.
- Add CONFIG_SENSORS_RASPBERRYPI_HWMON generic symbol.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
target/linux/archs38/image/Makefile calls gen_axs10x_sdcard_img.sh
with $(CONFIG_TARGET_ROOTFS_PARTSIZE).
Make sure a rootfs partition is built and usable.
Signed-off-by: Thomas Weißschuh <thomas@t-8ch.de>
Link: https://github.com/openwrt/openwrt/pull/16098
Signed-off-by: Robert Marko <robimarko@gmail.com>
6.1.103 and 6.6.44 introduced breakage complaining about missing mtd_test.ko
for some targets.
Signed-off-by: Zxl hhyccc <zxlhhy@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16093
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit ec885796c0 switched the crc32 implementation from default to
byte-at-a-time algorithm, which runs slower but consumes less memory.
A decade has passed, and we have already abandoned targets that had
small memory, so switch it back to default for faster speed.
Signed-off-by: Qingfang Deng <qingfang.deng@siflower.com.cn>
Enable the CONFIG_MTD_SPI_NOR_USE_VARIABLE_ERASE kernel option to allow for
U-Boot environment writing. This might be hiding a problem somewhere else,
since the w25q128fw chip supports 32K erases, still this change makes it
much easier to switch the GL-MV1000 boot media without an UART cable
connection.
Thanks to @robimarko and @hacks for the precious hints and suggesting a
better approach.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
This allows booting from internal eMMC or SD card just changing the
U-Boot mmc_dev variable.
In particular, setting mmc_dev to 1 will result in booting from the SD card.
Setting the variable to 0 will result in internal eMMC boot (the default).
Should the variable be unset or an error condition occur while reading
from SD card, internal MMC booting will be tried.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
mpc85xx was switched to 6.6. We can remove 6.1 support now.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16087
Signed-off-by: Robert Marko <robimarko@gmail.com>
It's time for wide tests.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16087
Signed-off-by: Robert Marko <robimarko@gmail.com>
The patches were generated from the RPi repo with the following command:
git format-patch v6.6.44..rpi-6.6.y
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Initially APK would sign packages and package index and verify
signatures individually. With the latest change, all packages inside a
trusted index are automatically trusted.
This is important within the OpenWrt eco-system since signing the index
happens on another machine than the package creation.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This adds auto-configuration of network ports on Dell EMC Edge620 (x86) product.
It is similar in specs/features to some of the Sophos x86-based appliances, but:
1. Serial console terminal is built in and requires just the micro-USB cable
2. Comes with both MMC (16Gb) and SSD (256Gb) installed
3. Comes with 6 ethernet ports all 6 are functional when no SFP is used
4. Comes with two SFP cages and not one, like some of revision 3 Sophos products
5. Unlike Sophos devices, there are no non-wireless models of Edge 620,
it comes with Qualcomm Atheros QCA9880 radio
These devices can be now found both second-hand and new at online marketplaces below
(sometimes well below) US $100, I believe they make great candidates for running OpenWrt.
The ethernet network ports on the case are marked GE1 thru to GE6 with the
following mapping once booted into OpenWrt:
```
GE1: eth2: pci0000:00/0000:00:0b.0/0000:02:00.2
GE2: eth3: pci0000:00/0000:00:0b.0/0000:02:00.3
GE3: eth0: pci0000:00/0000:00:0b.0/0000:02:00.0
GE4: eth1: pci0000:00/0000:00:0b.0/0000:02:00.1
GE5: eth7: pci0000:00/0000:00:17.0/0000:07:00.1
GE6: eth6: pci0000:00/0000:00:17.0/0000:07:00.0
```
Dell's instructions for [standard configuration](https://infohub.delltechnologies.com/en-us/l/dell-emc-edge-620-advanced-activation-guide/dell-emc-sd-wan-edge-620-standard-configuration/)
recommend using GE3, GE4, GE5, or GE6 for WAN, I've selected the GE6 as the sole
WAN port under OpenWrt with the rest of ethernet ports assigned to LAN.
Please merge before 24.xx is forked and if possible, cherry-pick for 23.05
if there's no ETA for 24.xx forking.
PS. @Hurricos I'm struggling with ixgbe mappings on Sophos devices which use
very similar hardware to Dell EMC, so even tho I know the sys paths for ethernet ports,
I'd prefer to do a separate commit to properly map ethernet ports to match the case markings
for this device at some point later.
Signed-off-by: Stan Grishin <stangri@melmac.ca>
