Delete the crypto-lib-blake2s kmod package, as BLAKE2s is now built-in.
Patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800, x86/64
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit cd634afe6c)
Major changes are:
Add support for smbd-direct multi-desctriptor.
Add support for dkms.
Add support for key exchange.
Fix seveal bugs.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit 95adbc24e7)
Small update to my previous path 'fix I2C on GL-AR300M devices'.
This update allow using GPIO17 as regular GPIO in case it not used
as I2C SDA line.
Signed-off-by: Ptilopsis Leucotis <PtilopsisLeucotis@yandex.com>
(cherry picked from commit 493080815d)
With the pinctrl configuration set properly by the previous commit, the
LED stays lit regardless of status of 2.4GHz radio, even if 5GHz radio
is disabled. Map GPIO19 as LED for ath9k, this way the LED will show
activity for both bands, as it is bound by logical AND with output of
ath10k-phy0 LED. This works well because during management traffic,
phy*tpt triggers typically cause LEDs to blink in unison.
Link: <https://github.com/openwrt/openwrt/pull/9941>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 5ca45e0a21)
The default configuration of pinctrl for GPIO19 set by U-boot was not a
GPIO, but an alternate function, which prevented the GPIO hog from
working. Set GPIO19 into GPIO mode to allow the hog to work, then the
ath10k LED output can control the state of actual LED properly.
Link: <https://github.com/openwrt/openwrt/pull/9941>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 82b5984636)
If you change SCAN_EXTRA variable with "-path target/linux/xxxx" in
include/toplevel.mk for speed up scan, find will warn with:
find: warning: you have specified the global option -maxdepth after
the argument -path, but global options are not positional, i.e.,
-maxdepth affects tests specified before it as well as those specified
after it. Please specify global options before other arguments.
The find option -mindepth -maxdepth are global options and must be
before any path option. Change order of $(SCAN_EXTRA) after -mindepth
and -maxdepth to fix this.
Signed-off-by: Leo Chung <gewalalb@gmail.com>
[capitalize Description, Author and Sob and minor description tweak]
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
(cherry picked from commit eb787b5b9d)
- fix an issues when accessing the port pointer of an expired/invalid fdb entry
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 38a5b593ef)
Buidbots are currently choking on the following compile error:
In file included from tools/aisimage.c:9:
include/image.h:1133:12: fatal error: openssl/evp.h: No such file or directory
# include <openssl/evp.h>
^~~~~~~~~~~~~~~
compilation terminated.
This is caused by a complete overriding of make flags which are provided
correctly in `UBOOT_MAKE_FLAGS` variable, but currently overriden
instead of extended. This then leads to the usage of build host include
dirs, which are not available.
Fix it by extending `UBOOT_MAKE_FLAGS` variable in all device recipes.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 481339a042)
Some dst in IPv6 flow offload table become invalid after the table is created.
So check_dst is needed in packet path.
Signed-off-by: Ritaro Takenaka <ritarot634@gmail.com>
[Add patch for kernel 5.15 too and rename file]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit efff48529b)
ucidef_set_bridge_device is needed for DGND3700v2 network config since VLAN 1
must be used for the switch to be correctly configured.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 90e4c8c6e6)
f2d6752901f2 blob: clear buf->head when freeing a buffer
45210ce14136 list.h: add container_of_safe macro
cfa372ff8aed blobmsg: implicitly reserve space for 0-terminator in string buf alloc
d2223ef9da71 blobmsg: work around false positive gcc -Warray-bounds warnings
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 3e300e724b)
Stop the connection when the control daemon is terminated. The code is
a modified version of the termination routine in version 4.23.1 of the
daemon (which doesn't support VR9 modems anymore).
This could also be implemented by calling the acos and acs commands via
dsl_cpe_pipe.sh in the init script. However, doing it in the daemon
itself has the advantage of also working if it is terminated in another
way (for example during sysupgrade).
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
(cherry picked from commit 1daaef31b3)
The driver maintains elapsed times by repeatedly accumulating the time
since the previous update in a loop. For the elapsed showtime time, the
time difference is truncated to seconds before adding it, leading to a
sizable error over time.
Move the truncation to before calculation of the time difference in
order to remove this error. Also maintain the total elapsed time in the
same way in full seconds, to prevent the unsigned 32-bit counter from
wrapping around after about 50 days.
Testing on a VR9 device shows that the reported line uptime now matches
the actual elapsed wall time. The ADSL variant is only compile-tested,
but it should also work as the relevant code is identical.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
(cherry picked from commit db4bf4b968)
Right now, both ltq-adsl-mei and ltq-vdsl-mei are always built, even
when they aren't necessary for the selected variant. This can cause the
build to fail, for example ltq-vdsl-mei doesn't build successfully here
on xway target due to the vectoring callback.
Make these dependencies conditional on the specific package variants,
so they are only built when actually needed.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
(cherry picked from commit 2f484aeff5)
Some users noticed repeated resyncs at random intervals, which go away
when the MEI driver is configured to use polling instead of interrupts.
Debugging shows that this seems to be caused by concurrent calls to
MEI_ReadMailbox (in the interrupt handler) and MEI_WriteMailbox. This
appears to be mostly triggered when there is an interrupt for vectoring
error reports.
In polling mode, calls to MEI_ReadMailbox are protected by the same
semaphore as is used in MEI_WriteMailbox. When interrupts are used,
MEI_WriteMailbox appears to rely on MEI_DisableDeviceInt and
MEI_EnableDeviceInt to provide mutual exclusion with the interrupt
handler. These functions mask/unmask interrupts, and there is an
additional check of the mask in the interrupt handler itself. However,
this is not sufficient on systems with SMP, as the interrupt handler
may be running in parallel, and could already be past the interrupt
mask check at this point.
This adds a lock to the interrupt handler, and also acquires this lock
in MEI_DisableDeviceInt. This should make sure that after a call to
MEI_DisableDeviceInt the interrupt is masked, and the interrupt handler
is either not running, has alread finished its work, or is still before
the interrupt mask check, and is thus going to detect the change.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
(cherry picked from commit 1700424553)
This tells the modem about the WAN MAC address, which is used as source
address for vectoring error reports that are generated by the firmware.
It needs to be set early, as the MEI driver only actually writes the
value to the modem when is in reset state (i.e. the firmware has been
loaded, but connection has not started yet).
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
(cherry picked from commit b35d33c8b8)
This re-enables the vectoring error sample callback and adds a
dependency to the corresponding driver.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
(cherry picked from commit 93f0e1f922)
In order to calculate the required pre-distortion for downstream
vectoring, the vectoring control entity (VCE) at the carrier office
needs error samples from the modem. On Lantiq VR9 modems, error reports
are generated by the firmware, but need to be multiplexed into the data
stream by the driver on the main processor when L2 encapsulation is
selected by the VCE.
This driver provides the necessary callback function, which is called by
the MEI driver after receiving an error report from the firmware.
Originally, it is part of the Lantiq PPA driver, but after a few changes
it also works with the PTM driver used in OpenWrt. The direct call to
ndo_start_xmit needs to be replaced, as the PTM driver relies on locks
from the kernel. Instead dev_queue_xmit is used, which is called from a
work queue, as it is not safe to call from an interrupt handler.
Additional changes include fixes to support recent kernel versions and
a change of the used interface from ptm0 to dsl0.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
(cherry picked from commit f872b96609)
A GPIO assert is required to reset the system. Otherwise, the system
will hang on reboot.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a2817ce96f17db3a5af77837ae5733b47182ae0d)
Tested in a DGS-1210-28 F3, both triggering failsafe and reboot.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit b85f59b726442621efb95153ff60b8767723feca)
Add NVRAM quirks script for the bcm53xx target. Split NVRAM quirks for the
bcm47xx and bcm53xx targets. Move clear partialboot NVRAM quirk for Linksys
EA9500 here. Add set wireless LED behaviour quirk for Asus RT-AC88U.
Use boot() instead of start() as nvram commands are meant to be executed
only once, at boot.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit f4e219fd5e)
Asus RT-AC88U is an AC3100 router featuring 9 Ethernet ports over the
integrated Broadcom and the external Realtek switch.
Hardware info:
* Processor: Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz
* Switch: BCM53012 in BCM4709C0KFEBG & external RTL8365MB
* DDR3 RAM: 512 MB
* Flash: 128 MB (ESMT F59L1G81LA-25T)
* 2.4GHz: BCM4366 4×4 2.4/5G single chip 802.11ac SoC
* 5GHz: BCM4366 4×4 2.4/5G single chip 802.11ac SoC
* Ports: 8 Ports, 1 WAN Ports
Flashing instructions:
* Boot to CFE Recovery Mode by holding the reset button while power-on.
* Connect to the router with an ethernet cable.
* Set IPv4 address of the computer to 192.168.1.2 subnet 255.255.255.0.
* Head to http://192.168.1.1.
* Reset NVRAM.
* Upload the OpenWrt image.
CFE bootloader may reject flashing the image due to image integrity check.
In that case, follow the instructions below.
* Rename the OpenWrt image as firmware.trx.
* Run a TFTP server and make it serve the firmware.trx file.
* Run the URL below on a browser or curl.
http://192.168.1.1/do.htm?cmd=flash+-noheader+192.168.1.2:firmware.trx+flash0.trx
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
[rmilecki: mark BROKEN until we sort out nvram & CFE recovery]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 72b9b721d7)
The ZyXEL GS1900-24E is a 24 port gigabit switch similar to other GS1900
switches.
Specifications
--------------
* Device: ZyXEL GS1900-24E
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB Macronix MX25L12835F
* RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8GE
* Ethernet: 24x 10/100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
24 ethernet port link/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESET" button on front panel
* Switch: 1 Power switch on rear of device
* Power 120-240V AC C13
* UART: 1 serial header (JP2) with populated standard pin connector on
the left side of the PCB.
Pinout (front to back):
+ Pin 1 - VCC marked with white dot
+ Pin 2 - RX
+ Pin 3 - TX
+ PIn 4 - GND
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware
* Select the HTTP radio button
* Select the Active radio button
* Use the browse button to locate the
realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
file and select open so File Path is updated with filename.
* Select the Apply button. Screen will display "Prepare
for firmware upgrade ...".
*Wait until screen shows "Do you really want to reboot?"
then select the OK button
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24E is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Raylynn Knight <rayknight@me.com>
(cherry picked from commit b515ad10a6)
Using nvmem-cells to set the MAC address for a DBDC device results in
both PHY devices using the same MAC address. This in turn will result in
multiple BSSes using the same BSSID, which can cause various problems.
Use the hotplug script for the EAP615-Wall instead to avoid this.
Fixes: a1b8a4d7b3 ("ramips: support TP-Link EAP615-Wall")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-By: Andrew Powers-Holmes <aholmes@omnom.net>
(cherry picked from commit ce90ba1f31)
mkimage limits the length of the file paths in can deal with to 256
characters. Turns out that in automated builds by asu we break this
limit, so increase it to 1024 characters.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 3fbf9689b6)
2f793a4 lua: add optional path filter to objects() method
2bebf93 ubusd: handle invoke on event object without data
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 1521d5f453)
2e1fcf4 netifd: fix hwmode for 60g band
39ef9fe interface-ip: fix memory corruption bug when using jail network namespaces
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 7eb83b2015)
557c98e init: selinux: don't relabel virtual filesystems
7a00968 init: only relabel rootfs if started from initramfs
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 4cbc26b212)
4b4849cf5e5a interface-ip: unify host and proto route handling
507c0513d176 interface-ip: add support for excluding interfaces in host route lookup
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 24cc341fdc)
56cb2d4 nas: add decoding of cell_id
9a9019a uqmi: wms - added storage to read text messages
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 51c442c265)
Aruba deploys a BDF in the root filesystem, however this matches the one
used for the DK04 reference board.
The board-specific BDFs are built into the kernel. The AP-365 shows
sinificant degraded performance with increased range when used with the
reference BDF.
Replace the BDF with the one extracted from Arubas kernel.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b21b98627d)
Currently malta configures the first Ethernet device as WAN interface.
If it finds a second one it will configure it as LAN.
This commit reverses it to match armvirt and x86. If there is only one
network device it will be configured as LAN device now. If we find two
network devices the 2. one will be WAN.
If no board.d network configuration is given it will be configured in
package/base-files/files/etc/board.d/99-default_network
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[minor typos]
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit fb1ba92202)
210991d fw4: prefer /dev/stdin if available
4e5e322 fw4: make `fw4 restart` behavior more robust
221040e ruleset: emit time ranges when both start and stop times are specified
30a7d47 fw4: fix datetime parsing
fb9a6b2 ruleset: correct mangle_output chain type
6dd2617 fw4: fix logic flaw in testing hw flow offloading support
c7c9c84 fw4: ensure that negative bitcounts are properly translated
c4a78ed fw4: fix typo in emitted set types
Fixes: #9764, #9923, #9927, #9935, #9955
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit a7ddef6ef1)
d996047 syntax: adjust number literal parsing and string to number conversion
9efbe18 lib: refactor `uc_int()`
da3f089 lib: rework uc_index() implementation
559029e ci: make jobs faster during pull request testing
Fixes: #9923
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(backported from commits 251e70c887 and
7f998088f0)
The label MAC address for DIR-825 Rev. B1 is the WAN address located
at 0xffb4 in `caldata`, which equals LAN MAC at 0xffa0 incremented by 1.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
(cherry picked from commit 4bed263af7)
Update the name of for the Ubiquiti NanoBeam M5 to match the
auto-generated one at runtime. Otherwise sysupgrade complains about
mismatching device names.
This also required renaming the DTS.
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
(cherry picked from commit 21a3ce97d5)
Ubiquiti NanoBeam M5 devices are CPE equipment for customer locations
with one Ethernet port and a 5 GHz 300Mbps wireless interface.
Specificatons:
- Atheros AR9342
- 535 MHz CPU
- 64 MB RAM
- 8 MB Flash
- 1x 10/100 Mbps Ethernet with passive PoE input (24 V)
- 6 LEDs of which four are rssi
- 1 reset button
- UART (4-pin) header on PCB
Notes:
The device was supported by OpenWrt in ar71xx.
Flash instructions (web/ssh/tftp):
Loading the image via ssh vias a stock firmware prior "AirOS 5.6".
Downgrading stock is possible.
* Flashing is possible via AirOS software update page:
The "factory" ROM image is recognized as non-native and then installed correctly.
AirOS warns to better be familiar with the recovery procedure.
* Flashing can be done via ssh, which is becoming difficult due to legacy
keyexchange methods.
This is an exempary ssh-config:
KexAlgorithms +diffie-hellman-group1-sha1
HostKeyAlgorithms ssh-rsa
PubkeyAcceptedKeyTypes ssh-rsa
User ubnt
The password is ubnt.
Connecting via IPv6 link local worked best for me.
1. scp the factory image to /tmp
2. fwupdate.real -m /tmp/firmware_image_file.bin -d
* Alternatively tftp is possible:
1. Configure PC with static IP 192.168.1.2/24.
2. Enter the rescue mode. Power off the device, push the reset button on
the device (or the PoE) and keep it pressed.
Power on the device, while still pushing the reset button.
3. When all the leds blink at the same time, release the reset button.
4. Upload the firmware image file via TFTP:
tftp 192.168.1.20
tftp> bin
tftp> trace
Packet tracing on.
tftp> put firmware_image.bin
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
(cherry picked from commit 4cd3ff8a79)
The MikroTik hAP (product code RB951Ui-2nD) is
an indoor 2.4Ghz AP with a 2 dBi integrated antenna built around the
Atheros QCA9531 SoC.
Specifications:
- SoC: Atheros QCA9531
- RAM: 64 MB
- Storage: 16 MB NOR - Winbond 25Q128FVSG
- Wireless: Atheros QCA9530 (SoC) 802.11b/g/n 2x2
- Ethernet: Atheros AR934X switch, 5x 10/100 ports,
10-28 V passive PoE in port 1, 500 mA PoE out on port 5
- 8 user-controllable LEDs:
· 1x power (green)
· 1x user (green)
· 4x LAN status (green)
· 1x WAN status (green)
· 1x PoE power status (red)
See https://mikrotik.com/product/RB951Ui-2nD for more details.
Notes:
The device was already supported in the ar71xx target.
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Maciej Krüger <mkg20001@gmail.com>
(cherry picked from commit 5ce64e0646)
The MikroTik RB952Ui-5ac2nD (sold as hAP ac lite) is an indoor 2.4Ghz
and 5GHz AP/router with a 2 dBi integrated antenna.
See https://mikrotik.com/product/RB952Ui-5ac2nD for more details.
Specifications:
- SoC: QCA9533
- RAM: 64MB
- Storage: 16MB NOR
- Wireless: QCA9533 802.11b/g/n 2x2 / QCA9887 802.11a/n/ac 2x2
- Ethernet: AR934X switch, 5x 10/100 ports,
10-28 V passive PoE in port 1, 500 mA PoE out on port 5
- 6 user-controllable LEDs:
- 1x user (green)
- 5x port status (green)
Flashing:
TFTP boot initramfs image and then perform sysupgrade. The "Internet"
port (port number 1) must be used to upload the TFTP image, then
connect to any other port to access the OpenWRT system.
Follow common MikroTik procedure as in
https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit 2bd33e8626)
c22eeef fw4: support negative CIDR bit notation
628d791 hotplug: reliably handle interfaces with ubus zone hints
d005293 fw4: store zone associations from ubus in statefile as well
b268225 fw4: filter non hw-offload capable devices when resolving lower devices
57984e0 fw4: always resolve lower flowtable devices
7782017 tests: fix mocked `fd.read("line")` api
72b196d config: remove restictions on DHCPv6 allow rule
f0cc317 fw4: refactor family selection for forwarding rules
b0b8122 treewide: use modern syntax
05995f1 fw4: fix emitting device jump rules for family restricted zones
b479815 fw4: fix family auto-selection for config nat rules
2816a82 ruleset: ensure that family-agnostic ICMP rules cover ICMPv6 as well
2379c3d tests: add test coverage for zone family selection logic
Fixes: #5066, #9611, #9765, #9854
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 2df17604a4)
