d49aadabb7a1 lib: fix dealing with udebugd restarts
9ec5fbb6aaad ubus: report ring size and data size via ubus api
86b4396baa44 ring: add debug messages for ring alloc errors
e02306af7c50 lib: add helper function for applying ring config
b613879cb049 client: send confirmation messages for ring add/remove
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Confiabits MT7981 is a Wi-Fi 6 router based on MediaTek MT7981.
Specification:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 128 MiB SPI NAND
- RAM: 256 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 4x 10/100/1000 Mbps MT7531AE (3xLAN, 1xWAN)
- USB 2.0 port
- Buttons: 1 Reset button, 1 Mesh button.
- LEDs: 7x light-blue, 2x warm-white
- Serial console: internal 4-pin header, 115200 8n1
- Power: 12 VDC, 1.5 A
MAC addresses in stock firmware and in this commit:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 00:0c:43:xx:xx:e1 | label+1 |
| LAN | 00:0c:43:xx:xx:e0 | label |
| WLAN 2g | 00:0c:43:xx:xx:e0 | label |
| WLAN 5g | 02:0c:43:xx:xx:e0 | |
+---------+-------------------+-----------+
The label MAC was found in 'Factory', 0x4
Installation:
The stock firmware is OpenWrt-based. If you can reach LuCI or SSH, just use the sysupgrade image
with the 'Keep settings' option turned off.
Signed-off-by: Luis Mita <luis@luismita.com>
GRUB_SERIAL is also used for the default serial on the target and not
only in grub. When no grub was build it was not available and the build
fails.
Rename GRUB_SERIAL to TARGET_SERIAL and make it always available on x86
and armsr targets.
Fixes: #14063
Fixes: b10768476f ("x86,armsr: interpolate GRUB_SERIAL into /etc/inittab")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Include XHCI USB drivers on the ZBT-Z8102AX router, the drivers are
required to be able to use the USB-connected M.2 slots for 4G/5G modems.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
b77f2a4ce903 uloop: fix build using C++ compilers
260ad5bd1566 udebug: add ulog support
e80dc00ee90c link librt if needed for shm_open
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2b39a27d8bcc libubus: fix reconnect with auto subscribe
f84eb5998c6e libubus: fix initial subscribe with autosubscribe
Signed-off-by: Felix Fietkau <nbd@nbd.name>
82fa6480de7a uloop: add support for interval timers
13d9b04fb09d uloop: add support for user defined signal handlers
f7d156911311 uloop: properly initialize signal handler mask
8a5a4319a85c uloop: fix typo in signal handling rework
b3fa3d92e3eb uloop: reset flags after __uloop_fd_delete call
d4c3066e7c5e udebug: add udebug library code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Hardware
--------
SoC: MediaTek MT7981BA
RAM: 1GB DDR4 (NANYA NT5AD512M16C4-JR)
MMC: 8GB eMMC (Samsung 8GTF4R)
ETH: 1000Base-T LAN (ePHY)
2500Base-T WAN (MaxLinear GPY211C)
BTN: 1x Reset Button
LED: System (blue/white)
VPN (white)
USB: 1x USB-A (USB 3.0)
UART: 115200 8N1 - Pinout on board next to LAN port
Don't connect 3.3V!
Known Issues
------------
U-Boot vendor recovery does not seem to accept any images, neither
GL.iNet images nor OpenWrt images. Recovery requires serial access!
Installation
------------
Upload the OpenWrt sysupgrade image to the Gl.iNet Web-UI. Make sure to
not retain existing settings.
Signed-off-by: David Bauer <mail@david-bauer.net>
All devices in the rockchip target have appended image-metadata. Enforce
the presence of this metadata to avoid flashing incomplete images.
This is the de-facto standard for almost all OpenWrt targets.
Signed-off-by: David Bauer <mail@david-bauer.net>
Now that MAC address parser supports the hex format (without
delimiters), use the canonical MAC address stored in U-boot partition.
Get rid of the userspace adjustments which are no longer necessary.
While at that, move the mac-base to the common part, as it is again
exactly the same in both models.
And convert ART partition too - keep that one separate, as calibration
data length differs between the models.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Now that MAC address parser supports the hex format (without
delimiters), use the canonical MAC address stored in U-boot partition.
Get rid of the "mac-address-increment" binding.
While at that, convert ART partition too.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Addresses were swapped compared to the factory firmware. In addition to
that, one of them was shifted by -1. Fix that by setting wlan0 MAC
offset to 9, and wlan1 MAC offset to 2.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
91666a3 ustream-mbedtls: Add compatibility with Mbed TLS 3.0.0
263b9a9 cmake: Fail if undefined symbols are used
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If the dnsmasq process forks to handle TCP connections, it closes the ubus
context. But instead of changing the daemon wide pointer to NULL, only the
local variable was adjusted - and this portion of the code was even dropped
(dead store) by some optimizing compilers.
It makes more sense to change the daemon->ubus pointer because various
functions are already checking it for NULL. It is also the behavior which
ubus_destroy() implements.
Fixes: d8b33dad0b ("dnsmasq: add support for monitoring and modifying dns lookup results via ubus")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Enable all necessary drivers for the rk356x SoCs, including PHY,
SCMI, SPI etc. Also backport 2 upstream patches for sdhci fixes.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
It's applicable for all devices so move it to default to reduce
redudant code. Addtionally introduce a new variable `BOOT_SCRIPT`
to allow custom boot script (if necessary).
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Currently there's no usable mainline (open source) TF-A implementation
for rk35xx SoCs, so pack the prebuilt firmware from the vendor.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Add correct NAND_SIZE in device definitions for EA6350v3, EA8300, MR8300,
WHW01 and WHW03v2, to enable improved image size checks wrt UBI reserved
blocks on NAND devices.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Many NAND devices use a build recipe with "append-ubi | check-size" to
ensure factory images don't exceed the target flash partition size.
However, UBI reserves space for bad block handling and other operational
overhead, and thus 'check-size' can overestimate the space available by
several MB. In practice, this means a failed check is definitely a failure,
while a passing check is only probably a pass.
Improve the situation by teaching 'Build/append-ubi' to check image sizes
while accounting for UBI reserved blocks. Add new device variable NAND_SIZE
and use with existing IMAGE_SIZE to derate the available space. Each UBI
device reserves 20 PEBs per 1024 PEBs of the entire NAND device for bad
blocks, plus an additional 4 PEBs overhead.
Many devices can transparently enable this check by setting NAND_SIZE based
on their flash storage, and may then remove any unneeded 'check-size'.
Link: http://www.linux-mtd.infradead.org/doc/ubi.html#L_overhead
Suggested-by: Shiji Yang <yangshiji66@qq.com>
Suggested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Current factory image sizes for Linksys devices are 256-byte aligned. This
is not an issue writing factory images from the OpenWrt or Linksys GUIs,
but can lead to failures using a TFTP client from the Linksys bootloader:
NAND write: device 1 offset 0x2800000, size 0xc00100
Attempt to write to non page aligned data
NAND write to offset 2800000 failed -22
0 bytes written: ERROR
Simplify Linksys footer creation by migrating to a makefile build recipe,
and pre-pad the footer (with 0xFF) to ensure the final image is $(PAGESIZE)
aligned. Finally, remove the old linksys-image.sh script no longer needed.
Linksys footer details are given below for future reference. The 256-byte
footer is appended to factory images and tested by both the Linksys
Upgrader (observed in EA6350v3) and OpenWrt sysupgrade.
Footer format:
.LINKSYS. Checked by Linksys upgrader before continuing. (9 bytes)
<VERSION> Upgrade version number, unchecked so arbitrary. (8 bytes)
<TYPE> Model of device, space padded (0x20). (15 bytes)
<CRC> CRC checksum of factory image to flash. (8 bytes)
<padding> Padding ('0' + 0x20 * 7) (8 bytes)
<signature> Signature of signer, unchecked so arbitrary. (16 bytes)
<padding> Padding with nulls (0x00) (192 bytes)
Link: https://github.com/openwrt/openwrt/pull/11405#issuecomment-1358510123
Link: https://github.com/openwrt/openwrt/pull/11405#issuecomment-1587517739
Reported-by: Stijn Segers <foss@volatilesystems.org>
Reported-by: Wyatt Martin <wawowl@gmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Add the make function 'exp_units' for helping evaluate k/m/g size units in
expressions, and use this to consistently replace many ad hoc substitutions
like '$(subst k,* 1024,$(subst m, * 1024k,$(IMAGE_SIZE)))' in makefiles.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Use lower-case "k" in IMAGE_SIZE for Linksys WHW01, permitting proper unit
conversions in build recipes (e.g. 75776k -> 75776*1024).
Fixes: 2a9f3b7717 ("ipq40xx: fix up Linksys WHW01 board name, device definition")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
D-Link DAP-1720 rev A1 is a mains-powered AC1750 Wi-Fi range extender,
manufactured by Alpha Networks [8WAPAC28.1A1G].
(in square brackets: PCB silkscreen markings)
Specifications:
* CPU (Qualcomm Atheros QCA9563-AL3A [U5]):
775 MHz single core MIPS 74Kc;
* RAM (Winbond W9751G6KB-25J [U3]):
64 MiB DDR2;
* ROM (Winbond W25Q128FV [U16]):
16 MiB SPI NOR flash;
* Ethernet (AR8033-AL1A PHY [U1], no switch):
1 GbE RJ45 port (no PHY LEDs);
* Wi-Fi
* 2.4 GHz (Qualcomm Atheros QCA9563-AL3A [U5]):
3x3 802.11n;
* 5 GHz (Qualcomm Atheros QCA9880-BR4A [U9]):
3x3 802.11ac Wave 1;
* 3 foldable dual-band antennas (U.fl) [P1],[P2],[P3];
* GPIO LEDs:
* RSSI low (red/green) [D2];
* RSSI medium (green) [D3];
* RSSI high (green) [D4];
* status (red/green) [D5];
* GPIO buttons:
* WPS [SW1], co-located with status LED;
* reset [SW4], accessible via hole in the side;
* Serial/UART:
Tx-Gnd-3v3-Rx [JP1], Tx is the square pin, 1.25mm pitch;
125000-8-n-1 in U-boot, 115200-8-n-1 in kernel;
* Misc:
* 12V VCC [JP2], fed from internal 12V/1A AC to DC converter;
* on/off slide switch [SW2] (disconnects VCC mechanically);
* unpopulated footprints for a Wi-Fi LED [D1];
* unpopulated footprints for a 4-pin 3-position slide switch (SW3);
MAC addresses:
* Label = LAN;
* 2.4 GHz WiFi = LAN;
* 5 GHz WiFi = LAN+2;
Installation:
* `factory.bin` can be used to install OpenWrt from OEM firmware via the
standard upgrade webpage at http://192.168.0.50/UpdateFirmware.html
* `recovery.bin` can be used to install OpenWrt (or revert to OEM
firmware) from D-Link Web Recovery. To enter web recovery, keep reset
button pressed and then power on the device. Reset button can be
released when the red status LED is bright; it will then blink slowly.
Set static IP to 192.168.0.10, navigate to http://192.168.0.50 and
upload 'recovery.bin'. Note that in web recovery mode the device
ignores ping and DHCP requests.
Note: 802.11s is not supported by the default `ath10k` driver and
firmware, but is supported by the non-CT driver and firmware variants.
The `-smallbuffers` driver variant is recommended due to RAM size.
Co-developed-by: Anthony Sepa <protectivedad@gmail.com>
Signed-off-by: Rani Hod <rani.hod@gmail.com>
