Init script won't append --no-dhcp-interface option if interface
protocol is one of: ncm, directip, qmi, mbim.
This is caused by IP address assigned to dynamically created netifd
interfaces. As a result there's no netmask assigned to the main
interface and dhcp_add() function returns prematurely.
By moving network subnet check we can ensure that --no-dhcp-interface is
properly generated for wwan interfaces.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase; move network checks]
Setting ipv6 to auto in case of a pppoe interface will trigger the
creation of a dynamic wan_6 interface meaning two IPv6 interfaces
(wan6 and wan_6) will be active on top of the pppoe interface.
This leads to unpredictable behavior in the network; therefore set
ipv6 to 1 which will prevent the dynamic creation of the wan_6
interface.
Further alias the wan6 interface on top of the wan interface for pppoe
as the wan6 interface can only be started when the link local address is
ready. In case of pppoe the link local address is negotiated during the
Internet Protocol Control Protocol when the PPP link is setup meaning
all the IP address info is only available when the wan interface is up.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Refresh patches.
Compile-tested on ipq8065/nbg6817 and x86/64.
Runtime-tested on ipq8065/nbg6817 and x86/64.
Fixes CVE-2017-1000251.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
[adapt qcom_nandc.c patches to match upstream changes, test ipq8065/nbg6817]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Delete a bunch of fixes that are already included.
Refresh patches.
Compile-tested on malta/mipsel
Runtime-tested on malta/mipsel
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
When bumping tcpdump from 4.9.1 to 4.9.2, I did not include the fixed
CVEs in the commit message. As the list of fixed CVEs is quite long,
we should probably mention them in the changelogs of the releases to
come. This commit will make sure this happens.
The following CVEs were fixed in 21014d9708:
CVE-2017-11541
CVE-2017-11541
CVE-2017-11542
CVE-2017-11542
CVE-2017-11543
CVE-2017-11543
CVE-2017-12893
CVE-2017-12894
CVE-2017-12895
CVE-2017-12896
CVE-2017-12897
CVE-2017-12898
CVE-2017-12899
CVE-2017-12900
CVE-2017-12901
CVE-2017-12902
CVE-2017-12985
CVE-2017-12986
CVE-2017-12987
CVE-2017-12988
CVE-2017-12989
CVE-2017-12990
CVE-2017-12991
CVE-2017-12992
CVE-2017-12993
CVE-2017-12994
CVE-2017-12995
CVE-2017-12996
CVE-2017-12997
CVE-2017-12998
CVE-2017-12999
CVE-2017-13000
CVE-2017-13001
CVE-2017-13002
CVE-2017-13003
CVE-2017-13004
CVE-2017-13005
CVE-2017-13006
CVE-2017-13007
CVE-2017-13008
CVE-2017-13009
CVE-2017-13010
CVE-2017-13011
CVE-2017-13012
CVE-2017-13013
CVE-2017-13014
CVE-2017-13015
CVE-2017-13016
CVE-2017-13017
CVE-2017-13018
CVE-2017-13019
CVE-2017-13020
CVE-2017-13021
CVE-2017-13022
CVE-2017-13023
CVE-2017-13024
CVE-2017-13025
CVE-2017-13026
CVE-2017-13027
CVE-2017-13028
CVE-2017-13029
CVE-2017-13030
CVE-2017-13031
CVE-2017-13032
CVE-2017-13033
CVE-2017-13034
CVE-2017-13035
CVE-2017-13036
CVE-2017-13037
CVE-2017-13038
CVE-2017-13039
CVE-2017-13040
CVE-2017-13041
CVE-2017-13042
CVE-2017-13043
CVE-2017-13044
CVE-2017-13045
CVE-2017-13046
CVE-2017-13047
CVE-2017-13048
CVE-2017-13049
CVE-2017-13050
CVE-2017-13051
CVE-2017-13052
CVE-2017-13053
CVE-2017-13054
CVE-2017-13055
CVE-2017-13687
CVE-2017-13688
CVE-2017-13689
CVE-2017-13690
CVE-2017-13725
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Do not create one big package with all the Intel firmware files
supported by the iwlwifi driver, but use a separate package for each
chip.
This also updates some 7000 and 8000 series firmware files to more
recent version. The older versions shipped are not supported by the
current driver any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
dev_coredumpm() was added with kernel 4.7, but it is used by iwlwifi.
When the dev coredump framework form compat-wireless is used this is not
a problem because it already contains this, but this is deactivated if
the build system finds out that it is already included in the kernel we
compile against. This option was now activated by the bluetooth driver
btmrvl. Having dev coredump in the kernel adds about 400 bytes to the
lzma compressed kernel for brcm47xx.
This is copied from a more recent backports version to add the
dev_coredumpm() function when the internal core devdump is not used.
Fixes: a5922f6 ("kernel: bluetooth: add marvell sdio bluetooth module")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes the build of this module and should fix the build bots.
Fixes: a5922f6 ("kernel: bluetooth: add marvell sdio bluetooth module")
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[removed mveub dependency and update commit comment]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
4.4.80+ contains 71a165f6397df07a06ce643de5c2dbae29bd3cfb, 4.9.41+ contains
6c78197e4a69c19e61dfe904fdc661b2aee8ec20 which are all backports of upstream
commit 0878fff1f42c18e448ab5b8b4f6a3eb32365b5b6 ("net: phy: Do not perform
software reset for Generic PHY").
Our local patch is no longer needed, all this patch was doing was utilizing
gen10g_soft_reset which does nothing either, so just keep the code unchanged.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
With the introduction of the ubus notifications, we would now fail building
dnsmasq with external toolchains that don't automatically search for headers.
Pass TARGET_CPPFLAGS to the Makefile to resolve that.
Fixes: 34a206bc11 ("dnsmasq: add ubus notifications for new leases")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We will be prompted with this config symbol when performance monitoring is
enabled in the kernel.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This commit add support for Marvell bluetooth with SDIO interface.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[Fix KCONFIG and FILES option]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
update firmware mrvl/sd8887_uapsta.bin
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[update to version 2017-09-06]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update e2fsprogs to 1.43.6
Disable compilation of fuse2fs (we don't package it)
Disable thread support (only affects fuse2fs)
Enable linking with libblkid instead of using private (included) version.
The libblkid is ~210KBytes in size, but with using the shared library
the binaries are ~25KBytes smaller. This also brings it in sync with
most other Linux distributions.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Some symbols have been renamed.
Some are default enabled/disabled, so we need
to adjust semantics against that.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
This seems to cause a false-positive warning/error
while building `libwebsockets-cyassl`.
```
make[6]: Leaving directory '/home/sandu/work/lede/build_dir/target-x86_64_musl/libwebsockets-cyassl/libwebsockets-2.2.1'
make[6]: Entering directory '/home/sandu/work/lede/build_dir/target-x86_64_musl/libwebsockets-cyassl/libwebsockets-2.2.1'
[ 2%] Building C object CMakeFiles/websockets.dir/lib/base64-decode.c.o
In file included from /home/sandu/work/lede/staging_dir/target-x86_64_musl/usr/include/wolfssl/ssl.h:31:0,
from /home/sandu/work/lede/staging_dir/target-x86_64_musl/usr/include/cyassl/ssl.h:33,
from /home/sandu/work/lede/staging_dir/target-x86_64_musl/usr/include/cyassl/openssl/ssl.h:30,
from /home/sandu/work/lede/build_dir/target-x86_64_musl/libwebsockets-cyassl/libwebsockets-2.2.1/lib/private-libwebsockets.h:256,
from /home/sandu/work/lede/build_dir/target-x86_64_musl/libwebsockets-cyassl/libwebsockets-2.2.1/lib/base64-decode.c:43:
/home/sandu/work/lede/staging_dir/target-x86_64_musl/usr/include/wolfssl/wolfcrypt/settings.h:1642:14: error: #warning "For timing resistance / side-channel attack prevention consider using harden options" [-Werror=cpp]
#warning "For timing resistance / side-channel attack prevention consider using harden options"
```
Hardening is enabled by default in libwolfssl at build-time.
However, the `settings.h` header is exported (along with other headers)
for build (via Build/InstallDev).
This looks like a small bug/issue with wolfssl.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
This is to eliminate any ambiguity about the cyassl/wolfssl lib.
The rename happened some time ago (~3+ years).
As time goes by, people will start to forget cyassl and
start to get confused about the wolfSSL vs cyassl thing.
It's a good idea to keep up with the times (moving forward).
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Until other packages from feeds decide to rename the
dependency of `+libcyassl` to `+libwolfssl`, this allows
for a bit of backwards compatibility with those packages.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Method used:
```
cd package/network/utils/wwan/files/data
sed -e 's/}}/}/g' -i *
sed -e 's/}\t"acm": 1/\t"acm": 1/g' -i *
sed -e 's/}\t"generic": 1/\t"generic": 1/g' -i *
```
Manually adjusted commas.
Validated with
```
for f in `ls` ; do echo $f ; python -m json.tool < $f || break ; done
```
Thanks to @lynxis for pointing out the commas.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Update e2fsprogs to 1.43.6
* Remove FreeBSD patch as it's not needed, FreeBSD 9.1 is EoL and this
is compiling on FreeBSD 11.1.
* Remove libmagic patch, RHEL 5 is EoL (End of Production Phase) since
March 31, 2017.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Bump gcc from 7.1 to 7.2
Compile & run tested: ar71xx
Trace history of current patches and update with commit ref & comment
to give more clue as to why they're still around/needed. Some have
changed form since the original commit but some clue is better than no
clue at all.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Instead of blindly enabling the odhcpd v6 server and RA server on the
lan port, only do that if the lan port protocol is "static"
This prevents the unhelpful case of a device being a dhcpv4 client and
v6 server on the same ethernet port.
Signed-off-by: Karl Palsson <karlp@etactica.com>
[PKG_SOURCE_DATE increase; odhcpd.defaults script cleanup]
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The factory partition of the Phicomm K2P contains two MAC addresses.
The lower MAC address is at offset 0xe006 and the higher one is at
offset 0xe000.
Use the lower MAC address as base mac-address which the switch driver
increments by one for the second (wan) vlan.
The MAC addresses are still inverted in contrast to the stock firmware
where the lower MAC address is used for wan. But at least the use of a
MAC address not intended/reserved for this particular board is fixed.
Signed-off-by: Jiawei Wang <me@jwang.link>
In commit b11c51916c ("ramips: Improve Sanlinking D240 config") I made
a mistake with regards GPIO numbering. And in addition to specifying the
wrong GPIO for controling the power of one of the mini-PCIe, I recently
discovered that the power of both slots can be controlled.
This patch specifies the correct GPIO for the left-most mini-PCIe slot
of the D240 (labeled power_mpcie2 since the slot is attached to SIM2),
and adds a GPIO that can be used to control the power of the other
mini-PCIe slot (labeled power_mpcie1).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[do not use the gpio active macros for the gpio-export value]
Signed-off-by: Mathias Kresin <dev@kresin.me>
TP-Link Archer C20 v1 is a router with 5-port FE switch and
non-detachable antennas. It's very similiar to TP-Link Archer C50.
Also it's based on MediaTek MT7620A+MT7610EN.
Specification:
- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 8x LED (GPIO-controlled*), 2x button, power input switch
- 1 x USB 2.0 port
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the blue part of the LED.
* MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't
work.
Factory image notes:
These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device.
We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash. So, to flash this device we must
to prepare image using original firmware from tp-link site with uboot.
Flash instruction:
Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot.
There are two ways to flash the device to LEDE:
1) Using tftp mode with UART connection and original LEDE image
- Place lede-ramips-mt7620-ArcherC20-squashfs-factory.bin in tftp
server directory
- Configure PC with static IP 192.168.0.66/24 and tftp server.
- Connect PC with one of LAN ports, power up the router and press
key "4" to access U-Boot CLI.
- Use the following commands to update the device to LEDE:
setenv serverip 192.168.0.66
tftp 0x80060000 lede-ramips-mt7620-ArcherC20-squashfs-factory.bin
erase tplink 0x20000 0x7a0000
cp.b 0x80060000 0x20000 0x7a0000
reset
- After that the device will reboot and boot to LEDE
2) Using tftp mode without UART connection but require some
manipulations with target image
- Download and unpack TP-Link Archer C20 v1 firmware from original web
site
- Split uboot.bin from original firmware by this command (example):
dd if=Archer_C20v1_0.9.1_4.0_up_boot(160427)_2016-04-27_13.53.59.bin of=uboot.bin bs=512 count=256 skip=1
- Create ArcherC20V1_tp_recovery.bin using this command:
cat uboot.bin lede-ramips-mt7620-ArcherC20-squashfs-factory.bin > ArcherC20V1_tp_recovery.bin
- Place ArcherC20V1_tp_recovery.bin in tftp server directory.
- Configure PC with static IP 192.168.0.66/24 and tftp server.
- Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
- Router will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
The implementation is not efficient on ar8xxx switches. It triggers high
CPU load and degrades device performance.
The high CPU load has been traced down to the ar8xxx_reg_wait() call in
ar8xxx_mib_op(), which has to usleep_range() till the MIB busy flag set
by the request to update the MIB counter is cleared.
This commit removes the get_port_stats() code introduced in 4d8a66d and
leaves a note for future hacker's beware.
Fixes: FS#1004
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Fix multiple syntax errors in shelscripts (of packages only)
These errors were causing many conditions to not working properly
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[increase PKG_RELEASE, drop command substitution from directip.sh]
Signed-off-by: Mathias Kresin <dev@kresin.em>
Set sysctl fs.suid_dumpable = 2
This allows suid processes to dump core according to kernel.core_pattern
setting. LEDE typically uses suid to drop root priviledge rather than
gain it but without this setting any suid process would be unable to
produce coredumps (e.g. dnsmasq)
Processes still need to set a non zero core file process limit ('ulimit
-c unlimited' or if procd used 'procd_set_param limits
core="unlimited"') in order to produce a core. This setting removes an
obscure stumbling block along the way.
>From https://www.kernel.org/doc/Documentation/sysctl/fs.txt
suid_dumpable:
This value can be used to query and set the core dump mode for setuid
or otherwise protected/tainted binaries. The modes are
0 - (default) - traditional behaviour. Any process which has changed
privilege levels or is execute only will not be dumped.
1 - (debug) - all processes dump core when possible. The core dump is
owned by the current user and no security is applied. This is
intended for system debugging situations only. Ptrace is unchecked.
This is insecure as it allows regular users to examine the memory
contents of privileged processes.
2 - (suidsafe) - any binary which normally would not be dumped is dumped
anyway, but only if the "core_pattern" kernel sysctl is set to
either a pipe handler or a fully qualified path. (For more details
on this limitation, see CVE-2006-2451.) This mode is appropriate
when administrators are attempting to debug problems in a normal
environment, and either have a core dump pipe handler that knows
to treat privileged core dumps with care, or specific directory
defined for catching core dumps. If a core dump happens without
a pipe handler or fully qualifid path, a message will be emitted
to syslog warning about the lack of a correct setting.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
The addresses were read from the 'config' partition, which would not always
contain the addresses at the same offsets, depending on the stock firmware
version used before flashing LEDE. Change this to get the addresses from
the 'product-info' partition, which is read-only.
Reported-and-tested-by: Andreas Ziegler <ml@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The ZBT WE1026-5G
(http://www.zbtlink.com/products/router/WE1026-5G.html) is the follow-up
to the ZBT WE1026 and is based on MT7620. For the previous WE1026, the
ZBT WE826 image could be used. However, as the name implies, the -5G
comes equipped with a 5GHz wifi radio. As the WE826 only has a 2.4GHz
radio, the addition of 5GHz means that a separate image is needed for
the WE1026-5G. I suspect that this image will also work on the previous
WE1026, but I don't have a device to test with.
The WE1026-5G has following specifications:
* CPU: MT7620A
* 1x 10/100Mbps Ethernet.
* 16 MB Flash.
* 64 MB RAM.
* 1x USB 2.0 port.
* 1x mini-PCIe slots.
* 1x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x 5GHz wifi (MT7612)
* 1x button.
* 3x controllable LEDs.
Works:
* Wifi.
* Switch.
* mini-PCIe slot. Only tested with a USB device (a modem).
* SIM slot.
* Sysupgrade.
* Button (reset).
Not working:
* The 5GHz WIFI LED is completely dead. I suspect the issue is the same
as on other devices with Mediatek 5Ghz wifi-cards/chips. The LED is
controlled by the driver, and mt76 (currently) does not support this.
Not tested:
* SD card reader.
Notes:
* The modem (labeled 3G/4G) and power LEDs are controlled by the
hardware.
* There is a 32MB version of this device available, but I do not have
access to it. I have therefor only added support for the 16MB version,
but added all the required infrastructure to make adding support for the
32MB version easy.
Installation:
The router comes pre-installed with OpenWRT, including a variant of
Luci. The initial firmware install can be done through this UI,
following normal procedure. I.e., access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to
keep existing settings.
Recovery:
If you brick the device, the WE1026-5G supports recovery using HTTP. Keep the
reset button pressed for ~5sec when booting to start the web server. Set the
address of the network interface on your machine to 192.168.1.2/24, and
point your browser to 192.168.1.1 to access the recovery UI. From the
recovery UI you can upload a firmware image.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
The upstream ath10k driver disables the intermediate softqueues for some
devices. This patch reverts that behaviour and always enables the
softqueues (and associated bufferbloat fixes). We have had reports of people
running this with good results:
https://lists.bufferbloat.net/pipermail/make-wifi-fast/2017-September/001497.html
This also refreshes mac80211 patches.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Currently, if the provided hash is unsupported (length different from 32
or 64 bytes), we happily download the requested file without any kind of
checksum verification.
This is quite dangerous and may provide a false sense of security, because
a single typo in the hash (e.g. one character deleted by mistake) may skip
checksum verification entirely.
Instead, fail immediately if we don't support the provided hash.
In particular, if an external package repository decides to change the
hash algorithm one day, we will now fail loudly instead of skipping
checksum verification without complaints.
Note: if some users of scripts/download.pl knowingly provide an empty hash
because they don't need checksum verification, this change will break
them. This does not seem to be the case currently, but if this feature is
ever needed, an option should be added to download.pl instead of relying
on the hash being empty.
Fixes: eaa4eba10a ("scripts/download.pl: add SHA-256 support")
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
On a TL-WN710N, this patch increases iperf performance from ~92.5 to ~93.5 mbps. Keep in mind the WN710N is a 100mbps device. I expect greater numbers from gigabit devices.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The cns3xxx interrupt controller uses a single register and as such
the 'mask' reg/functions must be used as opposed to the 'enable'/'disable'
reg/functions.
This fixes an issue that occurs if more than one GPIO on a specific controller
(there is GPIOA and GPIOB each having 32 GPIO's) uses interrupts. When one
would get enabled all others would be disabled prior to this patch.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Refresh patches.
Compile-tested on octeon and x86/64.
Runtime-tested on octeon and x86/64.
Fixes CVE-2017-11600.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Fixed an authentication bypass issue in SSL/TLS. When the TLS
authentication mode was set to 'optional',
mbedtls_ssl_get_verify_result() would incorrectly return 0 when the
peer's X.509 certificate chain had more than
MBEDTLS_X509_MAX_INTERMEDIATE_CA intermediates (default: 8), even when
it was not trusted. This could be triggered remotely on both the client
and server side. (Note, with the authentication mode set by
mbedtls_ssl_conf_authmode()to be 'required' (the default), the handshake
was correctly aborted).
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Tested-by: Magnus Kroken <mkroken@gmail.com>
This adds metadata to wpj344 and wpj558 images to prevent loading
firmware of wpj344 into wpj558 and vice versa. This until now was
possible and break the units and had to be recovered from the uboot.
Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
