Commit Graph

22634 Commits

Author SHA1 Message Date
Adrian Schmutzler
f0435d5343 ramips: rt3883: remove swconfig from individual DEVICE_PACKAGES
In rt3883 subtarget, several devices add swconfig to their DEVICE_PACKAGES.
This is redundant as the package is already provided via DEFAULT_PACKAGES.

Remove the redundant inclusions.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 23:07:49 +02:00
Adrian Schmutzler
40325abe52 ramips: remove (kmod-)swconfig DEVICE_PACKAGES for Sitecom WL-351
These definitions are not required since swconfig is selected for
the target anyway and kmod-swconfig is pulled as dependency by
kmod-switch-rtl8366rb.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 22:59:40 +02:00
Sungbo Eo
a1693bf626 ramips: explicitly disable built-in switch for lan-only devices
Commit 8f6334eb94 ("ramips: explicitly disable built-in switch when needed")
did not fix rt288x and rt3883 devices. This patch deals with them.

While at it, consolidate duplicate cases in interface setup.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-27 22:54:51 +02:00
Adrian Schmutzler
1553f58a98 ramips: create common definition for I-O DATA NAND devices
Three of the I-O DATA devices with NAND flash share a lot of
variables. Create a common definition for them to reduce duplicate
code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 22:37:23 +02:00
Yong-hyu, Ban
8fdf77878f mediatek: fix compile error caused by upstreamed mtk_m32 function
This fixes following compile error:

```
  CC      drivers/net/ethernet/mediatek/mtk_eth_soc.o
drivers/net/ethernet/mediatek/mtk_eth_soc.c:70:5: error: conflicting types for 'mtk_m32'
 u32 mtk_m32(struct mtk_eth *eth, u32 mask, u32 set, unsigned reg)
     ^~~~~~~
In file included from drivers/net/ethernet/mediatek/mtk_eth_soc.c:25:
drivers/net/ethernet/mediatek/mtk_eth_soc.h:964:6: note: previous declaration of 'mtk_m32' was here
 void mtk_m32(struct mtk_eth *eth, u32 clear, u32 set, unsigned reg);
      ^~~~~~~
```

which caused by 5.4.34 mainlining of mtk_m32 function.

Fixes: faf668be35 ("kernel: bump 5.4 to 5.4.34")
Signed-off-by: Yong-hyu, Ban <perillamint@quendi.moe>
2020-04-27 22:32:07 +02:00
INAGAKI Hiroshi
c998ae7f0e ramips: use lzma-loader for I-O DATA mt7621 devices
The official sysupgrade images for I-O DATA devices manufactured by
MSTC (MitraStar Technology Corp.) cannot be booted normally and the
kernel panics after switching to kernel 5.4.

This commit fixes the issue by using lzma-loader.

Note:
  These devices use Z-LOADER to read the kernel from NAND flash and boot
  it. Z-LOADER cannot load and start plain lzma-loader, so additional
  lzma-compression is needed.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Co-developed-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [wn-ax2033gr]
2020-04-27 12:22:02 +02:00
INAGAKI Hiroshi
a25bb8610f ramips: use lzma-loader for Japanese mt7621 devices
In several Japanese routers with MT7621 SoC, the official sysupgrade
image cannot be booted properly after switching to kernel 5.4.

This commit fixes the issue by using lzma-loader.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2020-04-27 12:22:02 +02:00
Szabolcs Hubai
ce19571004 ramips: mt7621: use lzma-loader for D-Link DIR-860L B1
This device has trouble extracting big kernel from flash,
and supports LZMA compressed kernels only.

Using OpenWrt kernel loader saves us 64 KB compared to the dictionary
size limiting workaround.

Factory image sizes (commit: 5f126c541a) with "CONFIG_ALL_KMODS=y":
- original ("-d23", default): 4784188 bytes, LZMA ERROR 1
- with "-d19": 4915260, LZMA ERROR 1
- with "-d18": 4915260, diff to original: +128 KB
- with "-d17": 4980796, diff to original: +192 KB
- with this patch: 4849724, diff to original: +64 KB

To save some CPU cycle, use minimal compression ("-a0") for the LZMA
compressed uImage.

The most robust solution would use a different loader,
which reads the compressed kernel directly from the flash.
See the thread at [0] for more details!

[0] http://lists.infradead.org/pipermail/openwrt-devel/2020-April/022926.html

Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
[fixed identation]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-27 12:22:02 +02:00
David Bauer
654eec5a2d ath79: enable SGMII workaround for affected boards
These boards suffer from a sudden inability to establish a link on the
SGMII. Enable the workaround to fix the link when it dies.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-27 12:22:02 +02:00
David Bauer
c760469918 ath79: ag71xx: unify version dependent code
Use IS_ERR_OR_NULL macro to use the same code on kernel 4.19 as well as
5.4.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-27 12:21:45 +02:00
David Bauer
5358d8b995 ath79: ag71xx: remove code for legacy kernels
ath79 does not support kernels prior to 4.19 anymore.
Remove legacy code for those kernels from the ag71xx driver.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-27 12:20:41 +02:00
David Bauer
3f5997fb28 ath79: remove unused TP-Link partition parser
This parser was added with the target, but no device seems to use it
currently, as all partitions are specified in the device-tree.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-27 12:20:41 +02:00
Adrian Schmutzler
3fdb08681b mvebu: tidy up support for GL.iNet GL-MV1000
This fixes a bunch of cosmetic issues with GL.iNet GL-MV1000:

- apply alphabetic sorting in multiple files
- use armada-3720 prefix for DTS like for other devices
- fix vendor capitalization for model in DTSes
- remove trivial comment in DTS files
- use DEVICE_VENDOR/DEVICE_MODEL
- remove redundant SUPPORTED_DEVICES
- use SOC instead of DEVICE_DTS
- remove empty line at EOF

Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 00:25:12 +02:00
DENG Qingfang
ad697aabc3 bcm53xx: 5.4: enable NAND
NAND driver was dropped in the 5.4 bump, so enable it back

Fixes: 50c6938b95 ("bcm53xx: add v5.4 support")
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-26 21:45:41 +02:00
Li Zhang
050c24f05c mvebu: add support for GL.iNet GL-MV1000
This patch adds supports for GL-MV1000.

Specification:
	- SOC: Marvell Armada 88F3720 (1GHz)
	- Flash: 16MB (W25Q128FWSIG)
	- RAM: 1GB DDR4
	- Ethernet: 3x GE (1 WAN + 2 LAN)
	- EMMC: 8GB EMMC (KLM8G1GETF-B041)
	- MicroSD: 1x microSD slot
	- USB: 1x USB 2.0 port(TypeA),1x USB 3.0 port(TypeC)
	- Button: 1x reset button,1x slide switch
	- LED: 3x greed LED
	- UART: 1x UART on PCB (JP1: 3.3V, RX, TX, GND)

	Update firmware instructions
	============================
	In the compiled,please gzip -d xxx.img.gz,then update firmware on uboot web.

Signed-off-by: Li Zhang <li.zhang@gl-inet.com>
[Copied dts file to files-5.4]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-04-26 21:45:41 +02:00
Matt Merhar
ee500186a5 kernel: backport fix for non-regular inodes on f2fs
Upstream commit dda9f4b9ca ("f2fs: fix to skip verifying block address
for non-regular inode").

On 4.14, attempting to perform operations on a non-regular inode
residing on an f2fs filesystem, such rm-ing a device node, would fail
and lead to a warning / call trace in dmesg. This fix was already
applied to other kernels upstream - including 4.19, from which the patch
was taken.

More info at https://bugzilla.kernel.org/show_bug.cgi?id=202495.

Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2020-04-26 21:45:41 +02:00
Sungbo Eo
1dedad2a00 ramips: remove unnecessary DEVICE_PACKAGES for Belkin F7C027
kmod-usb-dwc2 and kmod-usb-ledtrig-usbport are not target default packages, and
Belkin F7C027 does not have a USB port anyway. Just drop it.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-26 21:13:33 +02:00
Sungbo Eo
d16a486766 ramips: fix SUPPORTED_DEVICES for Mercury MAC1200R v2
Currently SUPPORTED_DEVICES only contains the old device string. Fix it by
removing the first assignment.

Fixes: c2334ad60d ("ramips/mt76x8: Synchronize Makefiles with DTS compatible")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-26 21:10:24 +02:00
Sungbo Eo
01961f163d oxnas: move service file to correct place
This service file has been misplaced from the very beginning.

Fixes: dcc34574ef ("oxnas: bring in new oxnas target")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-26 21:05:15 +02:00
Petr Štetiar
97d86426e2 x86: fix unusable squashfs images by adding missing padding
It was reported, that after image generation rework
x86-64-generic-squashfs-rootfs.img image won't boot on XenServer x86_64
anymore:

 F2FS-fs (xvda): Magic Mismatch, valid(0xf2f52010) - read(0x84289960)
 F2FS-fs (xvda): Can't find valid F2FS filesystem in 1th superblock
 F2FS-fs (xvda): Magic Mismatch, valid(0xf2f52010) - read(0x4e8ee223)
 F2FS-fs (xvda): Can't find valid F2FS filesystem in 2th superblock
 List of all partitions:
 ca00            4207 xvda
  driver: vbd
 No filesystem could mount root, tried:
  ext3
  ext2
  ext4
  squashfs
  iso9660
  f2fs

 Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(202,0)

So lets fix this by adding back padding which was introduced in commit
a17d9482f5 ("x86: image: fix small disk space in squashfs overlay").

Ref: FS#3036
Fixes: 258f070d1a ("x86: fix missing squashfs and ext4 rootfs images")
Fixes: cb007a7bf6 ("x86: switch image generation to new code")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-26 12:53:27 +02:00
René van Dorst
4c70bb4f90
ramips: enable SFP port for Ubiquiti ER-X-SFP
SFP cage of this device is connected via a AT8031 phy to port 5 of the switch.
This phy act as a RGMII-to-SerDes converter.

Also a I2C clock gate needs to be enabled in order to access the SFP module via I2C bus.
SFP cage also has module detect pin which is connected to I2C gpio expander.

With this patch the kernel/PHYLINK now can detect, readout and use the SFP module/port.

NOTE: SFP cage / AT8033 PHY only support 1000base-X encoding!
This means that some SGMII modules can work and only at forced 1GBit/full-duplex!

Signed-off-by: René van Dorst <opensource@vdorst.com>
2020-04-25 23:48:45 +02:00
René van Dorst
ec2f7a47d3 kernel: add module to support SFP cages
Enables kernel SFP case support.

Signed-off-by: René van Dorst <opensource@vdorst.com>
2020-04-25 23:45:16 +02:00
DENG Qingfang
6d924706a6 ramips: phy: at803x: support RGMII-to-SerDes and SFP support
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: René van Dorst <opensource@vdorst.com>
2020-04-25 23:45:16 +02:00
DENG Qingfang
63696bd0fb kernel: backport support for clause 37 1000Base-X auto-negotiation
This patch is needed for clause 37 1000Base-X encoding used in many SFP modules.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: René van Dorst <opensource@vdorst.com>
2020-04-25 23:45:16 +02:00
Petr Štetiar
ef5d37ba5e kernel: bump 5.4 to 5.4.35
Refreshed one patch.

Run tested: qemu-x86-64
Build tested: x86/64, imx6, sunxi/a53, rockchip/armv8

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-25 13:22:28 +02:00
Petr Štetiar
4a3e0f736f imx6: add back perf monitor related config symbol
Commit 0543eb1110 ("imx6: 5.4: add missing kernel perf monitor
symbol") has added missing kernel config symbol FSL_IMX8_DDR_PMU which
is exposed only when building perf, so add it back.

Fixes: 8d9b36270b ("imx6: refresh kernel config")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-25 13:22:28 +02:00
David Bauer
9fac9168c6 ipq40xx: fix alphabetical order in 02_network
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-24 20:03:41 +02:00
David Bauer
1f45ed6c99 ath79: fix QCA953x DDR and GPIO compatible bindings
The memory as well as GPIO controller had the wrong SoC name used for
their compatible binding.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-24 20:03:18 +02:00
David Bauer
fceef288cf ath79: correct QCA9550 machine compatible binding
Some boards using a QCA9556 or QCA9558 had their machine compatible
binding incorrectly set to qca,qca9557.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-24 20:03:00 +02:00
David Bauer
c0a80b7125 ath79: rename qca9557.dtsi to qca955x.dtsi
There are at least 3 different chips in the Scorpion series of SoCs.
Rename the common DTSI to better reflect it's purpose for the whole
series.

Also rename the compatible bindings from qca,ar9557 and qca,qca9557
to qca,qca9550.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-24 20:02:29 +02:00
Adrian Schmutzler
d3c9630811 ath79: move tplinkpart.c parser to patches
Between 4.19 and 5.4, mtd parsers have been moved to "parsers"
subdirectory. Like for myloader.c in the previous patch,
this patch moves tplinkpart.c to the kernel patches, so the
code and the kernel includes are at the same location and
the path can be adjusted per kernel.

While at it, remove some outdated kernel version switches from
the C code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-24 17:50:59 +02:00
Adrian Schmutzler
5f92349841 kernel: fix include of myloader.o since kernel 5.4
Between 4.19 and 5.4, mtd parsers have been moved to "parsers"
subdirectory. Based on this, the selection of myloader.o in OpenWrt
was also moved to that subdirectory, while the Kconfig and our local
myloader.c file remained in /drivers/mtd.

This resulted in linking errors like the following (on ath25@5.4):

make[8]: *** No rule to make target 'drivers/mtd/parsers/myloader.o', ...
   needed by 'drivers/mtd/parsers/built-in.a'.  Stop.
make[7]: *** [scripts/Makefile.build:500: drivers/mtd/parsers] Error 2
make[6]: *** [scripts/Makefile.build:500: drivers/mtd] Error 2

Since myloader.c is not too big, this patch moves it to the kernel patches,
allowing to adjust the path for kernel 5.4 and keeping Makefiles and
file paths better in sync.

Other patches have been refreshed accordingly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-24 17:50:12 +02:00
Adrian Schmutzler
58bec0d172 ramips: remove config-4.14 for mt7621/mt76x8
mt7621 and mt76x8 subtargets have been moved to kernel 5.4 and their
DTS(I) files are incompatible to kernel 4.14.

Remove the corresponding kernel config files to signal that more
boldly and to prevent accidentally patching the wrong kernel when
pulling in older config patches.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-23 18:39:48 +02:00
Adrian Schmutzler
f6573ec24e octeon: use kernel version 5.4 for testing
Tested on EdgeRouter Lite (by Daniel Engberg)

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-23 18:38:54 +02:00
Daniel Engberg
2095a4e276 octeon: update config for kernel 5.4
Update config with make kernel_oldconfig.

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[split patch, redo kernel_oldconfig, add description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-23 18:38:32 +02:00
Daniel Engberg
655c14e88c octeon: refresh patches for kernel 5.4
Refresh patches to make them apply to kernel 5.4.

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[split patch, refresh on newer kernel, add description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-23 18:38:26 +02:00
Daniel Engberg
91594cb137 octeon: copy files to kernel 5.4
Copy config and patches to kernel 5.4.

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[split patch, fix patches-5.4 dirname, add description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-23 18:38:19 +02:00
Felix Fietkau
df27e949fb mediatek: disable the unused pcie port for elecom wrc-2533gent
Fixes MSI support for the primary device

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-04-22 10:50:15 +02:00
Petr Štetiar
faf668be35 kernel: bump 5.4 to 5.4.34
Refreshed patches.

Run tested: qemu-x86-64, apalis, a64-olinuxino
Build tested: x86/64, imx6, sunxi/a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-21 22:16:33 +02:00
Koen Vandeputte
8d9b36270b imx6: refresh kernel config
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-04-21 14:46:52 +02:00
Alexander Couzens
36f628910b lantiq/fritz 7312: set maximum speed to 100 mbit
The fritz 7312 does not support 1000 gbit. Advertising it makes it
worse. Some NIC will change to 1000 gibt and turn off and on again for
ever.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2020-04-21 00:01:49 +02:00
Daniel Golle
be6543c539 x86: really remove packages already enabled in kconfig
This commit really removes packages in geode profiles already enabled
in kernel config.

Fixes: 9c23ecee57 ("x86: move packages selection to profiles")
Reported-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-04-20 19:24:18 +01:00
Tomasz Maciej Nowak
9c23ecee57 x86: move packages selection to profiles
This can be rather confusing for contributors, since there are three
layers in which they can be added. As for now there are none profiles
other than generic (exception: geos) let's move them to these profiles.
Being here this commit also removes packages in geode profiles already
enabled in kernel config.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-04-20 18:55:30 +01:00
Tomasz Maciej Nowak
eca6946447 x86: select kmod-button-hotplug by default
This package is useful by all subtargets, therefore move it to default
packages selection.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-04-20 18:55:30 +01:00
Tomasz Maciej Nowak
fd94d03ae6 x86: fix kmod-forcedeth package selection
There's no such package as forcedeth, threfore the driver is never
selected. Fix it by properly specifying package name.

Fixes: 35f208d ("x86: add nforce eth to default packages")
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-04-20 18:55:30 +01:00
Tomasz Maciej Nowak
282e7862b7 x86: image: drop dead code
These are remnants of old image generation code, which now serve no
purpose.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-04-20 18:55:30 +01:00
Tobias Mädel
6a05a85dcb rockchip: add support for Pine64 RockPro64
This adds the new rockchip target and support for RockPro64 RK3399

Flash:    16 MiB SPI NOR
RAM:      2 GiB/4 GiB LPDDR4
SoC:      RK3399
USB:      2x USB 2.0, 1x USB 3.0, 1x USB-C
Ethernet: 1x GbE
PCIe:     PCIe 2.0, 4 lanes
Storage:  eMMC or SD card
Optional SDIO wifi/bt module

The Pine64 RockPro64 is a single-board-computer with a 4x PCIe connector,
6 ARM64 cores (4 little, 2 big), plenty of RAM and storage.

By default the single Gigabit-Ethernet port is configured as the
LAN port.

Installation of the firware is possible by dd'ing the image
to an SD card or the eMMC flash.

Serial: 3v3 1500000 8n1

U-boot is build from the mainline tree and
integrated into the images. Required ATF to build u-boot
is downloaded from a CI build bot.

Signed-off-by: Tobias Mädel <t.maedel@alfeld.de>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
2020-04-20 16:37:56 +02:00
Pawel Dembicki
08f5cac6fb ramips: mt7621: add NETGEAR R7200 as DEVICE_ALT1
Netgear R7200 is another clone of Netgear R6700v2, introduced in:
6e80df5 ("ramips: add support for NETGEAR R6700v2/AC2400")

Reported-by: Joel Pinsker, github user @joelp64
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-04-20 11:13:39 +01:00
David Bauer
8d9c1087e4 ath79: add support for AVM FRITZ!WLAN Repeater 450E
SOC:    Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc
RAM:    64MB Zentel A3R12E40CBF DDR2
FLASH:  16MiB Winbond W25Q128 SPI NOR
WLAN1:  QCA9556 2.4 GHz 802.11b/g/n 3x3
INPUT:  WPS button
LED:    Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
        Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put openwrt-sysupgrade.bin mtd1

Note that this procedure might take up to two minutes.
You need to powercycle the device afterwards to boot OpenWRT.

Tested-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-19 16:45:40 +02:00
Sungbo Eo
45e2b7763f ramips: replace pinctrl property names for ipTIME A1004ns
The pinctrl driver had been replaced with the upstream one in b756ea2a90
("ramips: replace pinctrl property names"), but the initial A1004ns support
patch did not reflect the changes. This commit updates its pinctrl property
names.

Fixes: 9169482f64 ("ramips: add support for ipTIME A1004ns")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-19 13:47:23 +08:00
Álvaro Fernández Rojas
d27e2c67ed bcm63xx: switch to 5.4 kernel
Seems stable after 6 days of testing on some of my devices.
Let's switch to 5.4 in order to get more feedback.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-04-18 20:58:38 +02:00
Chuanhong Guo
19d9db5a96 ramips: mt7621: use lzma-loader for newifi d1/d2/thunder timecloud
These devices failed to properly extract kernel. enable lzma loader
for them.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-18 14:19:38 +08:00
Chuanhong Guo
1e5d014ba2 ramips: don't reuse KERNEL_DTB for lzma-loader
mt7621 overrides KERNEL_DTB to limit dictionary size, which isn't needed
for our lzma loader.
This saves 15KB on mt7621 devices using uimage-lzma-loader.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-18 13:40:31 +08:00
Chuanhong Guo
51c6b14092 ramips: mt7621: backport more pcie driver fixes
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-18 13:06:48 +08:00
Sungbo Eo
13a185bf8a ramips: increase spi-max-frequency for ipTIME mt7620 devices
This commit increases the hardware SPI frequency from 24.2MHz to 48.3MHz.

[    5.314163] m25p80 spi0.0: speed: 24166666/40000000, rate: 8, prescal: 2, loops: 226
[    5.076323] m25p80 spi0.0: speed: 48333333/50000000, rate: 4, prescal: 1, loops: 162

`time cat /dev/mtd2 >/dev/null` is reduced from 5.64s to 4.36s on A104ns,
and from 11.39s to 8.81s on A1004ns.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-18 12:35:54 +08:00
Sungbo Eo
9169482f64 ramips: add support for ipTIME A1004ns
ipTIME A1004ns is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.

Specifications:
- SoC: MT7620A
- RAM: DDR2 128MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7610EN
- Ethernet: 5x 10/100/1000Mbps
  - Switch: MT7530BU
- USB: 1x 2.0
- UART:
  - J2: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-18 12:35:54 +08:00
René van Dorst
d682dcc939 ramips: mt7621: Ubiquiti ER-X-SFP: fix gpio numbers for POE enable gpios
With v5.4 kernel a new gpio driver is used.
GPIO numbering has changed so update 03_gpio_switches too.

Signed-off-by: René van Dorst <opensource@vdorst.com>
2020-04-18 11:59:41 +08:00
René van Dorst
2fac1322f7 ramips: mt7621: Ubiquiti ER-X: fix gpio number for POE enable gpio
With v5.4 kernel a new gpio driver is used.
GPIO numbering has changed so update 03_gpio_switches too.

Signed-off-by: René van Dorst <opensource@vdorst.com>
2020-04-18 11:59:41 +08:00
DENG Qingfang
d74fb0088c ramips: use all reserved space for HiWiFi HC5962
These stock partitons: "backup", "hw_panic", "overly", firmware_backup", "opt"
do not contain any device-specific data and can be used for /overlay, resulting in
121M space

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-18 11:52:12 +08:00
DENG Qingfang
7dc82528a2 ramips: increase HiWiFi HC5962 kernel partition to 4M
Increase kernel partition because 2M is insufficient for 5.4
Because the partition changes, previous version of OpenWrt cannot upgrade
to this version, and requires a new installation

Recovery to stock instruction:
1. Download stock firmware at
   http://ur.ikcd.net/HC5962-sysupgrade-20171221-b00a04d1.bin
2. Power off the router
3. Press and hold the reset button for 4~6 sec while power it back on
4. Connect a PC to router's LAN
5. Visit http://192.168.2.1 and upload the firmware

Then repeat the instruction in edae3479e6 to install OpenWrt

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-18 11:50:57 +08:00
Mantas Pucka
4745969ad7 generic: spi-nor: fix 4-byte opcode support for w25q256
There are 2 different chips (w25q256fv and w25q256jv) that share
the same JEDEC ID. Only w25q256jv fully supports 4-byte opcodes.
Use SFDP header version to differentiate between them.

Fixes broken reboot on 8devices Habanero since f0f35fdac

Signed-off-by: Mantas Pucka <mantas@8devices.com>
2020-04-18 11:37:06 +08:00
Petr Štetiar
23916bca61 kernel: bump 5.4 to 5.4.33
Refreshed patches, removed upstreamed patches:

 oxnas: 001-irqchip-versatile-fpga-Handle-chained-IRQs-properly.patch
 oxnas: 002-irqchip-versatile-fpga-Apply-clear-mask-earlier.patch

Run tested: qemu-x86-64, apalis
Build tested: x86/64, imx6, sunxi/a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-17 15:18:12 +02:00
David Bauer
edf812e25c ath79: remove stray pipe
Fixes: 8918c038f3 ("ath79: add support for AVM FRITZ!WLAN Repeater 1750E")

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-17 14:15:09 +02:00
David Bauer
8918c038f3 ath79: add support for AVM FRITZ!WLAN Repeater 1750E
This commit adds support for the AVM Fritz!WLAN Repeater 1750E

SOC:	Qualcomm QCA9556 (Scorpion) 720MHz MIPS74Kc
RAM:    64MB Zentel A3R12E40CBF DDR2
FLASH:  16MiB Winbond W25Q128 SPI NOR
WLAN1:  QCA9556 2.4 GHz 802.11b/g/n 3x3
WLAN2:  QCA9880 5 GHz 802.11 n/ac 3x3
INPUT:  WPS button
LED:    Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
        Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi (correct MAC)
 - 5 GHz WiFi (correct MAC)
 - Installation via EVA bootloader
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put openwrt-sysupgrade.bin mtd1

Note that this procedure might take up to two minutes.
You need to powercycle the Device afterwards to boot OpenWRT.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-17 13:27:40 +02:00
David Bauer
d883eaacd4 ath79: add QCA9550 reset sequence
The QCA9550 family of SoCs have a slightly different reset
sequence compared to older chips.

Normally the bootloader performs this sequence, however
some bootloader implementation expect the operating system
to clear the reset. Also get the PCIe resets from OF to
support the second RC of the QCA9558.

This is required for the AVM FRITZ!WLAN Repeater 1750E to work,
as EVA leaves the PCIe bus in reset.

Tested: AVM FRITZ!WLAN Repeater 1750E - OCEDO Koala

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-17 13:23:06 +02:00
Koen Vandeputte
75ef28be59 kernel: add support for GD25D05 SPI NOR (5.4)
This chip is used on newer RB912UAG-5HPnD r2 and 922UAGS-5HPacD boards:

Before:

[    0.824562] spi-nor spi0.0: unrecognized JEDEC id bytes: c8 40 10 c8 40 10
[    0.831607] spi-nor: probe of spi0.0 failed with error -2

After:

[    0.825347] spi-nor spi0.0: gd25d05 (64 Kbytes)
[    0.830291] 1 routerbootpart partitions found on MTD device spi0.0
[    0.836577] Creating 1 MTD partitions on "spi0.0":
[    0.841448] 0x000000000000-0x000000010000 : "partitions"
[    0.848418] 4 routerbootpart partitions found on MTD device partitions
[    0.855092] Creating 4 MTD partitions on "partitions":
[    0.860318] 0x000000000000-0x00000000c000 : "routerboot"
[    0.866548] 0x00000000c000-0x00000000d000 : "hard_config"
[    0.872832] 0x00000000d000-0x00000000e000 : "bios"
[    0.878580] 0x00000000e000-0x00000000f000 : "soft_config"

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-04-16 14:36:35 +02:00
Roger Pueyo Centelles
c0430b8da4 ath79: reduce spi-max-frequency for Mikrotik wAP G-5HacT2HnD
The previous spi-max-frequency value did not work with all the CPU speed
settings (configurable with rbcfg or from the stock firmware); the new
one does for the three of them.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2020-04-16 13:44:18 +02:00
Koen Vandeputte
20efd5614a ath79: MikroTik: fix missing nand on kernel 5.4
Following symbol got renamed upstream:
CONFIG_MTD_NAND --> CONFIG_MTD_RAW_NAND

Also add this renamed symbol so NAND also works on kernel 5.4.

After:
[    0.628372] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
[    0.634862] nand: Samsung NAND 128MiB 3,3V 8-bit
[    0.639554] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.647263] Scanning device for bad blocks
[    0.656228] random: fast init done
[    0.789652] 3 fixed-partitions partitions found on MTD device ar934x-nand
[    0.796550] Creating 3 MTD partitions on "ar934x-nand":
[    0.801874] 0x000000000000-0x000000040000 : "booter"
[    0.807715] 0x000000040000-0x000000400000 : "kernel"
[    0.813551] 0x000000400000-0x000008000000 : "ubi"

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-04-16 13:23:11 +02:00
Koen Vandeputte
3c3825436e kernel: bump 4.19 to 4.19.115
Refreshed all patches.

Remove upstreamed:
- 600-ipv6-addrconf-call-ipv6_mc_up-for-non-Ethernet-inter.patch
- 184-USB-serial-option-add-Wistron-Neweb-D19Q1.patch

Fixes:
- CVE-2020-8647
- CVE-2020-8648 (potentially)
- CVE-2020-8649

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-04-16 13:23:11 +02:00
Koen Vandeputte
e31d158c4d kernel: bump 4.14 to 4.14.176
Refreshed all patches.

Remove upstreamed:
- 0001-net-thunderx-workaround-BGX-TX-Underflow-issue.patch
- 600-ipv6-addrconf-call-ipv6_mc_up-for-non-Ethernet-inter.patch
- 184-USB-serial-option-add-Wistron-Neweb-D19Q1.patch

Fixes:
- CVE-2020-8648 (potentially)
- CVE-2020-8647
- CVE-2020-8649

Compile-tested on: cns3xxx, octeontx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-04-16 13:23:11 +02:00
Hannu Nyman
a7423fef32 ath79: improve status LED definitions for GL-AR750
Improve the status LED functionality in GL-AR750
by adding the definitions for different statuses
(boot, failsafe, running, flashing).

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-04-16 00:02:03 +02:00
Adrian Schmutzler
508462a399 ath79: add SUPPORTED_DEVICES for TP-Link TL-WA901ND v2
This adds the board name from ar71xx to support upgrade without
-F for the TP-Link TL-WA901ND v2.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-15 12:47:43 +02:00
Chuanhong Guo
ad19751edc ramips: mt7621: enable lzma-loader for some devices
ubnt er-x/xiaomi/netgear sercomm devices are known to have troble
extracting a big kernel from flash and has support for uncompressed
uimage
This commit uses uncompressed uimage with lzma-loader for these devices
to fix boot issue.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-15 10:14:19 +08:00
Paul Spooren
f814121600 x86: append metadata to combined images
Now that the x86 target uses the new image generation code we can also
attach metadata to the created images.

As currently the `SUPPORTED_DEVICES` list is empty, no JSON metadata is
attached, however the signing happens in the same step.

This results in signature verification for x86 images.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-04-14 23:38:08 +01:00
Petr Štetiar
0bea89a1d0 kernel: bump 5.4 to 5.4.32
Refreshed patches, removed upstreamed patches:

 generic: 746-stable-net-dsa-mt7530-fix-null-pointer-dereferencing-in-por.patch

Run tested: qemu-x86-64, apalis
Build tested: x86/64, imx6, sunxi/a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-14 21:58:16 +02:00
Ansuel Smith
9abf01246e ipq806x: add patch to fix broken buttons
From kernel 4.20 msm-gpio driver is broken and cause the
malfunction of the buttons on every ipq806x target.
Add a patch to fix this.

Tested-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2020-04-14 21:58:16 +02:00
Adrian Schmutzler
d0cb6e995b ath79: further fixes for ZyXEL NBG6716
This applies further fixes to the DTS of ZyXEL NBG6716 based on
what is found in ar71xx (mach-nbg6716.c):

- use WiFi label names as in ar71xx
- fix WPS gpio number
- fix GPIO_ACTIVE_HIGH and mode for WiFi switch
- add codes for USB eject buttons
- fix node name for "internet" LED

This device has separate LEDs for WAN and "Internet". As the WAN-LED
(and the four LAN-LEDs) are driven independent of the setup in
DT/01_leds, the "internet" LED is left unassigned (in contrast to
ar71xx, where it was set up effectively as a second WAN LED)

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-14 12:03:57 +02:00
Chuanhong Guo
75f19deb3a ramips: define image recipe for uncompressed uimage with loader
Some devices have bootloaders with broken lzma code resulting in failed
decompression or corrupted kernel code.
This image recipe allows to sacrifice 5KB for OpenWrt LZMA loader and
take over the task of decompress kernel.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-14 12:01:50 +08:00
Chuanhong Guo
d9e9a0e6b1 ramips: define lzma loader platform in target
Loader platform is a per-soc variable instead of a per-device one.
Determine corresponding loader platform at the beginning of image
Makefile.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-14 11:17:47 +08:00
Chuanhong Guo
111029bea7 ramips: add missing DEVICE_VARS for lzma-loader
LOADER_TYPE is a per-device variable which should be included in
DEVICE_VARS.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-14 11:14:15 +08:00
Luiz Angelo Daros de Luca
1b2c4af039 ath79: enable m25p,fast-read for tplink,tl-wr1043-v1
Enables spi-mem interface for 3x faster flash read.

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
2020-04-14 10:47:23 +08:00
Luiz Angelo Daros de Luca
e430dfdd69 ath79: enable m25p,fast-read for tplink,tl-wr2543-v1
Enables spi-mem interface usage. It speeds up flash read
in about 3x while it also workaround a possible hardware
bug when normal spi read is used.

Fixes: FS#2742

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
2020-04-14 10:47:23 +08:00
Luiz Angelo Daros de Luca
b3f9842330 ath79: add read support using spi-mem
Reimplements read optimization on top of spi-mem. Similar to
what 461-spi-ath79-add-fast-flash-read.patch used to do with
the dropped flash read interface.

It accelerate only fast-read op reading flash directly from
memory mapped region. 'm25p,fast-read' must be set in order
to use the new spi-mem.

It improved read speed up to 3x on old devices (tplink,tl-wr2543-v1)
while no speed improvement was noticed on newer devices like
(tplink,archer-c7-v2).

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
2020-04-14 10:47:23 +08:00
Alberto Bursi
35f208da3c x86: add nforce eth to default packages
forcedeth is necessary to use the integrated
ethernet controller of Nvidia nForce chipset.

There are PC motherboards with this chipset
from 2001 that run 32bit Athlon XP CPUs and
more modern ones up to 2009 that can run Intel
and AMD 64bit processors, so add this to
all non-geode x86 targets.

Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
2020-04-13 22:41:37 +02:00
Tomasz Maciej Nowak
779a1c84ea mvebu: drop armada-37xx PCI aardvark patches
These patches were necessarry for Atheros and some Intel WiFi cards.
After short testing, the current upstream driver state is enough for
these WiFi cards to work. If there are still some issues with other
devices, the patches could be easily restored.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-04-13 22:41:37 +02:00
DENG Qingfang
f72a13b537 mvebu: refresh config
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-13 22:41:37 +02:00
DENG Qingfang
d13fe4127c mvebu: refresh patches
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-13 22:41:37 +02:00
DENG Qingfang
ae183c128f mvebu: set kernel testing version to 5.4
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-13 22:41:37 +02:00
DENG Qingfang
70193703a9 mvebu: copy files and patches to 5.4
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-13 22:41:37 +02:00
Daniel González Cabanelas
85ef69b202 mvebu: add support for Buffalo LinkStation LS421DE
Buffalo LinkStation LS421DE is a dual bay NAS, based on Marvell Armada 370

Hardware:
   SoC:         Marvell Armada 88F6707-A1
   CPU:         Cortex-A9 1200 MHz, 1 core
   Flash:       SPI-NOR 1 MiB, NAND 512 MiB
   RAM:         DDR3 512 MiB
   Ethernet:    1x 10/100/1000 Mbps
   USB:         1x 2.0, 1x 3.0
   SATA:        2x 3.0 Gbps
   LEDs/Input : 5x / 2x (1x button, 1x slide-switch)
   RTC:         Ricoh RS5C372A, I2C, no battery

Flash instruction (UART+TFTP):
  1. Downgrade the OEM firmware to 1.34 version (BUFFALO_BOOTVER=0.13)
  2. Remove any hard drive from inside the bays.
  3. Boot the Openwrt initramfs image using the U-Boot serial console:
         tftpboot 0x1200000 buffalo_ls421de-initramfs-kernel.bin
         bootm 0x1200000
  4. Flash the sysupgrade image using the Openwrt console:
         sysupgrade -n buffalo_ls421de-squashfs-sysupgrade.bin
  5. Wait until it finish, the device will reboot with Openwrt installed
     on the NAND flash.

Note:
  - Device shuting down doesn't work, even if the power slide switch is
    used. We must first, via MDIO, set the unused LED2 at the ethernet
    phy0 to off state. Reboot works ok.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-04-13 22:41:14 +02:00
Aleksander Jan Bajkowski
b43023b7ba kernel: remove non-existant symbols
These symbols exist only in older kernels and can be removed.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-04-13 22:40:19 +02:00
Adrian Schmutzler
97af28d23e ath79: fix USB port LED assignment for ZyXEL NBG6716
The USB LED assignment to internal ports was swapped.

Fix it.

We also explicitly checked that the LED label numbers match those
on the device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-13 19:22:16 +02:00
Guillaume Lefebvre
f5a9181d6e ath79: fix wmac initialization for Zyxel NBG6716
2.4 GHz Wifi on ath79 is set up in 10-ath9k-eeprom, but in ar71xx
it was done with ath79_register_wmac.

Thus, the following errors are observed on the device:
ath: phy1: Unable to initialize hardware; initialization status: -5
ath9k 18100000.wmac: failed to initialize device
ath9k: probe of 18100000.wmac failed with error -5

This patch changes the ath79 support to properly use wmac as well.
This will also require fixing the MAC address in a different way.

Signed-off-by: Guillaume Lefebvre <guillaume@zelig.ch>
[several adjustments to 10-fix-wifi-mac, use correct MAC address,
rewrite commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-13 19:21:56 +02:00
Chuanhong Guo
77b99ea3c6 ramips: fix whitespace in 990_NET-no-auto-carrier-support.patch
Fixes: 6fcba5eec3 ("ramips: port 0034-NET-multi-phy-support.patch to 5.4")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-13 11:49:16 +08:00
Chuanhong Guo
4d06229242 ramips: ralink-eth: fix leftover dma dev argument
Fixes: 05dee5833a ("ramips: ralink-eth: fix device struct passed to dma functions")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-13 11:32:50 +08:00
Jonas Gorski
4e535d81ee bcm63xx: disable all devices with <= 4MiB flash and <= 32 MiB RAM
Device with 4 MiB flash and 32 MiB RAM won't be able to run OpenWrt in
a sufficient manner without tweaks, so don't build images for them by
default.

This includes all BCM6338, BCM6345 and BCM6348 "generic" devices,
as there are no supported devices of these with more than that.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2020-04-12 20:45:21 +02:00
Chuanhong Guo
b756ea2a90 ramips: replace pinctrl property names
Upstream pinctrl driver in drivers/staging uses
groups/function/ralink,num-gpios instead of
ralink,group/ralink,function/ralink,nr-gpio
Replace these properties in dts as well as the pinctrl driver in
patches-4.14.
This commit is created using:
sed -i 's/ralink,group/groups/g'
sed -i 's/ralink,function/function/g'
sed -i 's/ralink,nr-gpio/ralink,num-gpios/g'

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:29:17 +08:00
Chuanhong Guo
8f6334eb94 ramips: explicitly disable built-in switch when needed
previously we rely on the failsafe setup in preinit scripts to disable
built-in switch implicitly for single-port devices. This doesn't work
anymore due to preinit script removal.
this patch explicitly disable built-in switch for needed devices.

Fixes: a8d62a4eb1 ("ramips: remove set_preinit_iface script")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:29:17 +08:00
Chuanhong Guo
605a7ffff2 ramips: add 5.4 as testing kernel
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Chuanhong Guo
abadee5d60 ramips: mt76x8: switch to kernel 5.4
4.14 doesn't work anymore due to gpio dt binding changes. Switch mt76x8
to 5.4 directly.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Chuanhong Guo
d7d46da938 ramips: disable images for 4M devices
default initramfs for 5.4 kernel is larger than 4M, causing build error
for oversized initramfs image.
disable these images because we have no mechanism for ignoring initramfs
errors and the squashfs image will be larger than initramfs anyway.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Chuanhong Guo
e29e2a9484 ramips: ralink-eth: add support for 5.4 kernel
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Chuanhong Guo
0b68d081eb ramips: mt7628: update dts for upstream gpio-mt7621 driver
upstream driver merged 3 separated gpio banks into one gpio node.
and gpioX Y in our local driver should be replaced with gpio X*32+Y.

This patch is created using the following sed command:
sed -i -r 's/(.*)gpio([0-9]) ([0-9]+)(.*)/echo "\1gpio $((\2*32+\3))\4"/ge'

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Chuanhong Guo
e320435a6a ramips: refresh kernel config for 5.4
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Chuanhong Guo
89bf2b18af ramips: copy kernel config for 5.4
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Chuanhong Guo
6fcba5eec3 ramips: port 0034-NET-multi-phy-support.patch to 5.4
This hack is needed for old ethernet driver:
On mt7620, we have two exposed RGMII ports that connects to builtin
switch. However, swconfig has no way to interact with phy subsystem.
As a result, we have to register both PHYs to ethernet mac instead
and this patch prevents main ethernet interface from going down due
to phy link changes.
Also rename the patch for its actual purpose.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Chuanhong Guo
05dee5833a ramips: ralink-eth: fix device struct passed to dma functions
dma functions needs the struct from platform_device instead of
the one for ethernet interface.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:17 +08:00
Chuanhong Guo
33d027c5b8 ramips: move and rename out-of-tree mtk eth driver
move the driver into shared 'files' directory and rename all symbols
from mediatek/mtk to ralink.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:17 +08:00
Chuanhong Guo
b0ec8d0ca0 ramips: increase spi frequency for newifi d1/d2
increase spi frequency for both devices to 45MHz.
while at it, also remove m25p,fast-read for newifi d1 as it's only
needed when spi clock is higher than 50MHz.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:17 +08:00
Chuanhong Guo
5c8f2c64d7 ramips: enable broken-flash-reset for some 32M flash boards
These are boards known to start on 3-byte address mode, which requires
broken-flash-reset if 4B_OPCODES isn't supported by the flash.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:17 +08:00
Chuanhong Guo
dfa521f129 generic: spi-nor: rework broken-flash-reset
Instead of resetting flash to 3B address on remove hook, this
implementation only enters 4B mode when needed, which prevents more
unexpected reboot stuck. This implementation makes it only break when
a kernel panic happens during flash operation on 16M+ areas.
Also silent broken-flash-reset warning. We are not dealing with vendors
and it's unpleasant for users to see that unnecessary and long WARN_ON
print.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:17 +08:00
Adrian Schmutzler
de3e5de8cc cns3xx: remove support for kernel 4.14
This target has been on kernel 4.19 for nine months now [1], and
has had testing support for even longer [2].
This should be long enough to drop support for kernel 4.14.

[1] 545bfbc3a9 ("cns3xxx: switch to kernel 4.19")
[2] c6bebe1a94 ("cns3xxx: add support for kernel 4.19")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 13:43:52 +02:00
Adrian Schmutzler
e8931b309f ramips: mt7621: tidy up names for Ubiquiti devices
The "proper" vendor prefix for Ubiquiti is "ubnt", this is used in
all targets except ramips and also recommended by the kernel.

This patch adjusts the various board/image/device name variables
accordingly. Since we touch it anyway, this also adds the space
in "EdgeRouter X" as a hyphen to those variables to really make
them consistent with the model name.

While at it, create a real shared definition for the devices in
image/mt7621.mk instead of deriving one device from another.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 13:25:42 +02:00
Adrian Schmutzler
bebc9809d1 bcm63xx: remove support for kernel 4.19
Since stable kernel for this target is still 4.14, kernel 4.19
has never been used much (and actually was broken for some devices).

So, since we bump testing kernel to 5.4, there is no real need to
keep 4.19 and have an additional version to care about.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 12:48:38 +02:00
Adrian Schmutzler
51b07e782d bcm63xx: use kernel 5.4 as testing kernel
This uses 5.4 as testing kernel. Since 4.19 has not seen broad
testing yet, just keep 4.14 as stable kernel until 5.4 is ready.

Tested on Comtrend AR-5387un (Thanks to @Noltari).

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 12:46:26 +02:00
Adrian Schmutzler
cb2f0df784 bcm63xx: 5.4: fix compilation for changed driver_find_device
In kernel patch 92ce7e83b4e5 ("driver_find_device: Unify the match
function with class_find_device()") the arguments of functions used
with driver_find_device are adjusted. Do the same for our local
user.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 12:45:56 +02:00
Adrian Schmutzler
8a2118e1b4 bcm63xx: 5.4: add removed helper syscon_regmap_lookup_by_pdevname
The helper syscon_regmap_lookup_by_pdevname has been removed in kernel patch
29d14b668d2f ("mfd: Remove unused helper syscon_regmap_lookup_by_pdevname")
due to lack of users.

However, we use this function in our local pinctrl drivers for BCM6358 and
BCM6368. Thus, we have to add it locally.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 12:44:57 +02:00
Adrian Schmutzler
43d3ef91f1 bcm63xx: prevent fall-through in kernel patches for 5.4
In kernel 5.4 -Werror=implicit-fallthrough is treated as error:

arch/mips/bcm63xx/cpu.c: In function 'detect_cpu_clock':
arch/mips/bcm63xx/cpu.c:158:2: error: this statement may fall through [-Werror=implicit-fallthrough=]
  {
  ^
arch/mips/bcm63xx/cpu.c:179:2: note: here
  case BCM6328_CPU_ID:
  ^~~~
cc1: all warnings being treated as errors

This can be fixed by adding "Fall through" as a comment where intended,
and has to be fixed by returning a proper default otherwise.

In case of the default clock frequency for BCM6318 we fixed this by
returning the default value taken from BCM6328 and BCM6362.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 12:43:55 +02:00
Adrian Schmutzler
6c521f6828 bcm63xx: fix missing watchdog core dependency
This patch follows the other patches that added the watchdog
core to various (armvirt, malta, ath79, ...) targets that
have been hit by the following build error:

Package kmod-hwmon-sch5627 is missing dependencies for the following libraries:
watchdog.ko

In theory, we could have just added the CONFIG_WATCHDOG_CORE=y
to the Kconfig variable of kmod-hwmon-sch5627's package definition.
This would have forced the watchdog core to be builtin and less
architectures would need to be updated. But we might as well follow
through here.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 12:40:06 +02:00
Adrian Schmutzler
f0fbc47a91 bcm63xx: update config for kernel 5.4
Update config with make kernel_oldconfig.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 12:39:22 +02:00
Adrian Schmutzler
04c07e05a1 bcm63xx: refresh patches for kernel 5.4
Refresh patches to make them apply to kernel 5.4.

The removed patches have been merged upstream.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 12:36:43 +02:00
Adrian Schmutzler
f8f1dc6eab bcm63xx: copy files to kernel 5.4
Copy config and patches to kernel 5.4.
make kernel_oldconfig has been run on 4.19 beforehand.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 12:36:21 +02:00
Yanase Yuki
e66becb490 ramips: add support for I-O DATA WN-AX2033GR
I-O DATA WN-AX2033GR is roughly the same as I-O DATA
WN-AX1167GR2. The difference is Wi-Fi feature.

Specification
=============
- SoC: MediaTek MT7621A
- RAM: DDR3 128 MiB
- Flash Memory: NAND 128 MiB (Spansion S34ML01G200TF100)
- Wi-Fi: MediaTek MT7603E
- Wi-Fi: MediaTek MT7615
- Ethernet: 5x 10 Mbps / 100 Mbps / 1000 Mbps (1x WAN, 4x LAN)
- LED: 2x green LED
- Input: 2x tactile switch, 1x slide switch
- Serial console: 57600bps, PCB through hole J5 (Vcc, TX, RX, NC, GND)
- Power: DC 12V

This device only supports channel 1-13 and 36-140.
Thus, narrower frequency limits compared to other devices are required
for limiting wi-fi frequency correctly.
Without this, non-supported frequencies are activated.

Flash instructions
==================
1. Open the router management page (192.168.0.1).
2. Update router firmware using "initramfs-kernel.bin".
3. After updating, run sysupgrade with "sysupgrade.bin".

Recovery instructions
=====================
WN-AX2033GR contains Zyxel Z-LOADER
1. Setup TFTP server (IP address: 10.10.10.3).
2. Put official firmware into TFTP server directory (distribution site:
   https://www.iodata.jp/lib/software/w/2068.htm)
3. Connect WX-AX2033GR Ethernet port and computer that runs TFTP server.
4. Connect to serial console.
5. Interrupt booting by Esc key.
6. Flash firmware using "ATNR 1,[firmware filename]" command.

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
[adjust for kernel 5.4, add recovery instructions/frequency comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 00:43:09 +02:00
Jo-Philipp Wich
93294b516e generic: drop 616-net_optimize_xfrm_calls.patch
The conditional check introduced by this patch may trigger a NULL pointer
dereference in case the result of dev_net() is NULL.

Since the purpose of this patch is neither sufficiently explained and since
this patch apparently has never been submitted upstream despite it being in
the pending-* patch directory, I propose to drop it without replacement.

If the performance implications of dropping this patch are found to be
significiant, it should be reintroduced with proper description and
benchmark results.

Ref: https://bugs.openwrt.org/index.php?do=details&task_id=2943
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-04-12 00:08:05 +02:00
Pawel Dembicki
c30220d458 ipq40xx: add support for Cell C RTL30VW
Cell C RTL30VW is a LTE router with tho gigabit ethernets and integrated
QMI mPCIE modem.

This is stripped version of ASKEY RTL0030VW.

Hardware:

Specification:
-CPU: IPQ4019
-RAM: 256MB
-Flash: NAND 128MB + NOR 16MB
-WiFi: Integrated bgn/ac
-LTE: mPCIe card (Modem chipset MDM9230)
-LAN: 2 Gigabit Ports
-USB: 2x USB2.0
-Serial console: RJ-45 115200 8n1
-Unsupported VoIP

Known issues:

None so far.

Instruction install:

There are two methods: Factory web-gui and serial + tftp.

Web-gui:
1. Apply factory image via stock web-gui.

Serial + initramfs:
1. Rename OpenWrt initramfs image to "image"
2. Connect serial console (115200,8n1)
3. Set IP to different than 192.168.1.11, but 24 bit mask, eg. 192.168.1.4.

4. U-Boot commands:
sf probe && sf read 0x80000000 0x180000 0x10000
setenv serverip 192.168.1.4
set fdt_high 0x85000000
tftpboot 0x84000000 image
bootm 0x84000000

5. Install sysupgrade image via "sysupgrade -n"

Back to stock:

All is needed is swap 0x4c byte in mtd8 from 0 to 1 or 1 to 0,
do firstboot and factory reset with OFW:

1. read mtd8:
dd if=/dev/mtd8 of=/tmp/mtd8
2. go to tmp:
cd /tmp/
3. write first part of partition:
dd if=mtd8 of=mtd8.new bs=1 count=76
4. check which layout uses bootloader:
cat /proc/mtd
5a. If first are kernel_1 and rootfs_1 write 0:
echo -n -e '\x00' >> mtd8.new
5b. If first are kernel and rootfs write 1:
echo -n -e '\x01' >> mtd8.new
6. fill with rest of data:
dd if=mtd8 bs=1 skip=77 >> mtd8.new
7. CHECK IF mtd8.new HAVE CHANGED ONLY ONE BYTE! e.g with:
hexdump mtd8.new
8. write new mtd8 to flash:
mtd write mtd8.new /dev/mtd8
9. do firstboot
10.reboot
11. Do back to factory defaults in OFW GUI.

Based on work: Cezary Jackiewicz <cezary@eko.one.pl>

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-04-10 15:22:26 +02:00
DENG Qingfang
a30abb1b6b ipq40xx: add support for MobiPromo CM520-79F
MobiPromo CM520-79F is an AC1300 dual band router based on IPQ4019

Specification:

SoC/Wireless: QCA IPQ4019
RAM: 512MiB
Flash: 128MiB SLC NAND
Ethernet PHY: QCA8075
Ethernet ports: 1x WAN, 2x LAN
LEDs: 7 LEDs
      2 (USB, CAN) are GPIO
      other 5 (2.4G, 5G, LAN1, LAN2, WAN) are connected to a shift register
Button: Reset

Flash instruction:
Disassemble the router, connect UART pins like this:
 GND TX    RX
  [x x . . x .]
  [. . . . . .]

(QCA8075 and IPQ4019 below)
Baud-rate: 115200

Set up TFTP server: IP 192.168.1.188/24
Power on the router and interrupt the booting with UART console
env backup (in case you want to go back to stock and need it there):
	printenv
	(Copy the output to somewhere save)
Set bootenv:
	setenv set_ubi 'set mtdids nand0=nand0; set mtdparts mtdparts=nand0:0x7480000@0xb80000(fs); ubi part fs'
	setenv bootkernel 'ubi read 0x84000000 kernel; bootm 0x84000000#config@1'
	setenv cm520_boot 'run set_ubi; run bootkernel'
	setenv bootcmd 'run cm520_boot'
	setenv bootargs
	saveenv
Boot initramfs from TFTP:
	tftpboot openwrt-ipq40xx-generic-mobipromo_cm520-79f-initramfs-fit-zImage.itb
	bootm
After initramfs image is booted, backup rootfs partition in case of reverting to stock image
	cat /dev/mtd12 > /tmp/mtd12.bin
Then fetch it via SCP

Upload nand-factory.ubi to /tmp via SCP, then run
	mtd erase rootfs
	mtd write /tmp/*nand-factory.ubi rootfs
	reboot

To revert to stock image, restore default bootenv in uboot UART console
	setenv bootcmd 'bootipq'
	printenv
use the saved dump you did back when you installed OpenWrt to verify that
there are no other differences from back in the day.
	saveenv
upload the backed up mtd12.bin and run
	tftpboot mtd12.bin
	nand erase 0xb80000 0x7480000
	nand write 0x84000000 0xb80000 0x7480000
The BOOTCONFIG may have been configured to boot from alternate partition (rootfs_1) instead
In case of this, set it back to rootfs:
	cd /tmp
	cat /dev/mtd7 > mtd7.bin
	echo -ne '\x0b' | dd of=mtd7.bin conv=notrunc bs=1 count=1 seek=4
	for i in 28 48 68 108; do
		dd if=/dev/zero of=mtd7.bin conv=notrunc bs=1 count=1 seek=$i
	done
	mtd write mtd7.bin BOOTCONFIG
	mtd write mtd7.bin BOOTCONFIG1

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[renamed volume to ubi to support autoboot,
as per David Lam's test in PR#2432]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-04-10 15:22:26 +02:00
Christian Lamparter
8ce138607e apm821xx: use the real default HZ value from upstream
With the "real HZ" debate out of the way, let's actually
use the apm821xx's default upstream config file at
arch/powerpc/configs/44x/bluestone_defconfig. From what
I can tell, it sets NO_HZ (well, this platform was for
NAS, so this is a bit unexpected) and remove any specific
HZ_$VALUE symbol.

Sadly, Daniel Engberg didn't run any before/after netperf
tests, because it would have been such a slam dunk across
the boards. In case of the apm821xx the tcp tx/rx
performance improved ~14% (from 600Mbps to 700Mps).
This now causes the emac to drop frames too, so let's see
if this is causes more problems or not.

This patch includes a refresh of the configuration too.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-04-10 15:20:30 +02:00
Pawel Dembicki
8b93a24208 ramips: mt7620: fix missplaced line in 01_leds
This patch adds missed line in 01_leds and fix error:

"/bin/board_detect: /etc/board.d/01_leds: line 93:
syntax error: unexpected ")" (expecting ";;")"

Fixes: c948a47 ("ramips: add support for D-Link DWR-960")

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-04-10 10:00:25 +02:00
李国
4a0f426ba5 x86: add genisoimage and xorrisofs as alternatives to mkisofs
Some system not have mkisofs, but have genisoimage or
xorrisofs. They have compatable options for mkisofs,
so let them as alternatives to mkisofs.

Signed-off-by: 李国 <uxgood.org@gmail.com>
2020-04-09 12:51:10 +02:00
李国
32f675ca9f x86: fix grub-bios-setup fail during sysupgrade
grub-bios-setup requires two images (boot.img and core.img),
but they are missing. This make an error during sysupgrade:
Upgrading bootloader on /dev/sda...
grub-bios-setup: error: cannot open `/tmp/boot/boot/grub/boot.img': No
such file or directory.

Signed-off-by: 李国 <uxgood.org@gmail.com>
2020-04-09 12:51:10 +02:00
Stefan Lippers-Hollmann
fabcfa9222 ipq40xx: re-add LEDS_LP5523 for the ASUS Lyra MAP-AC2200
This symbol had been enabled in the initial device support submission
for kernel 4.14, but apparently got lost during the v4.19 port.

The ASUS Lyra MAP-AC2200 has a single (very bright) rgb LED, which is
controlled by the TI/National LP5523/55231 LED driver chip. It is left
enabled in a pulsating infinite rainbow loop by the bootloader,
expecting it to be reconfigured (disabled by default) after the boot
process has finished and is also required to indicate failsafe/
firstboot conditions.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2020-04-09 12:51:10 +02:00
Roman Hampel
cd510e775b ath79: add support for Comfast CF-WR752AC v1
Specifications:

- Qualcomm QCA9531 + QCA9886
- dual band, antenna 2*3dBi
- Output power 50mW (17dBm)
- 1x 10/100 Mbps LAN RJ45
- 128 MB RAM / 16 MB FLASH (w25q128)
- 3 LEDs (red/green/blue)
  incorporated in
  "color wheel reset switch"
- UART 115200 8N1

Flashing instructions:

 The U-boot bootloader contains a recovery HTTP server
 to upload the  firmware. Push the reset button while powering the
 device on and keep it pressed for ~10 seconds. The device's LEDs will
 blink several times and the recovery page will be at
 http://192.168.1.1; use it to upload the sysupgrade image.

 Alternatively, the original firmware is based on OpenWrt so a
 sysupgrade image can be installed via the stock web GUI. Settings from
 the original firmware will be saved and restored on the new one, so a
 factory reset will be needed. To do so, once the new firmware is flashed,
 enter into failsafe mode by pressing the reset button several times during
 the boot process, until it starts flashing. Once in failsafe mode, perform
 a factory reset as usual.

LED-Info:

 The LEDs on the Comfast stock fw have a very proprietary behaviour,
 corresponding to the user selected working mode (AP, ROUTER or REPEATER).
 In the first two cases, only blue is used for status and LAN signaling. When
 using the latter, blue is always off (except for sysupgrade), either red
 signals bad rssi on master-link, or green good. Since the default working
 mode of OpenWrt resembles that of a router/AP, the default behavior is
 implemented accordingly.

MAC addresses (art partition):

location  address (example)    use in vendor firmware
0x0       xx:xx:xx:xx:xc:f8 -> eth0
0x6       xx:xx:xx:xx:xc:fa -> wlan5g (+2)
0x1002    xx:xx:xx:xx:xc:f9 -> not used
0x5006    xx:xx:xx:xx:xc:fb -> not used
---       xx:xx:xx:xx:xd:02 -> wlan2g (+10)

The same strange situation has already been observed and documented
for COMFAST CF-E560AC.

Signed-off-by: Roman Hampel <rhamp@arcor.de>
Co-developed-by: Joao Albuquerque <joaohccalbu@gmail.com>
Signed-off-by: Joao Albuquerque <joaohccalbu@gmail.com>
[adjust and extend commit message, rebase, minor DTS adjustments,
add correct MAC address for wmac, change RSSI LED names and behavior]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-09 01:06:37 +02:00
Petr Štetiar
b299002877 kernel: bump 5.4 to 5.4.31
Refreshed patches, removed upstreamed patches:

 oxnas:   003-ARM-dts-oxnas-Fix-clear-mask-property.patch
 generic: 184-USB-serial-option-add-Wistron-Neweb-D19Q1.patch

Run tested: apu2, qemu-x86-64, apalis
Build tested: sunxi/a53, imx6, x86/64, ipq40xx

Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> [apu2]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-09 00:12:46 +02:00
Bjørn Mork
196cab719f kernel: generic: 5.4: fix mips command line parameter patch
Fixing a build error when CONFIG_KERNEL_KEXEC is enabled:

make[5]: Entering directory '/home/bjorn/tmp/tmp-lede/build_dir/target-mipsel_24kc_musl/linux-ramips_mt7621/linux-5.4.28'
  CALL    scripts/checksyscalls.sh
  CALL    scripts/atomic/check-atomics.sh
  CHK     include/generated/compile.h
  CC      arch/mips/kernel/machine_kexec.o
arch/mips/kernel/machine_kexec.c: In function 'kexec_nonboot_cpu_jump':
arch/mips/kernel/machine_kexec.c:268:27: error: 'relocate_new_kernel_size' undeclared (first use in this function); did you mean 'kexec_relocate_new_kernel_end'?
      reboot_code_buffer + relocate_new_kernel_size);
                           ^~~~~~~~~~~~~~~~~~~~~~~~
                           kexec_relocate_new_kernel_end
arch/mips/kernel/machine_kexec.c:268:27: note: each undeclared identifier is reported only once for each function it appears in
arch/mips/kernel/machine_kexec.c: In function 'kexec_reboot':
arch/mips/kernel/machine_kexec.c:306:27: error: 'relocate_new_kernel_size' undeclared (first use in this function); did you mean 'kexec_relocate_new_kernel_end'?
      reboot_code_buffer + relocate_new_kernel_size);
                           ^~~~~~~~~~~~~~~~~~~~~~~~
                           kexec_relocate_new_kernel_end
make[7]: *** [scripts/Makefile.build:266: arch/mips/kernel/machine_kexec.o] Error 1

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2020-04-09 00:12:46 +02:00
Linus Walleij
780264980b gemini: Refine package list
The NAS packages for Gemini doesn't even include the
block-mount package. Augment the list to be based off
the DEFAULT_PACKAGES.nas to make sure we extend on the
essentials.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-04-09 00:12:46 +02:00
Ansuel Smith
2bdd669752 ipq806x: switch to 5.4 kernel
ipq806x has been tested for a lot and lots of people reported good results.
Switch the main kernel to 5.4 following the other targets.

Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065, NBG6817]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2020-04-09 00:12:46 +02:00
Alexey Dobrovolsky
fea232ae8f ramips: use full 8MB flash on ZyXEL Keenetic
ZyXEL Keenetic has 8MB flash, but OpenWrt uses only 4MB.
This commit fixes the problem.

WikiDevi page [1] says that ZyXEL Keenetic has FLA1: 8 MiB, there is
an article with specs [2] (in Russian).

[1] https://wikidevi.wi-cat.ru/ZyXEL_Keenetic
[2] https://3dnews.ru/608774/page-2.html

Fixes: FS#2487
Fixes: a7cbf59e0e ("ramips: add new device ZyXEL Keenetic as kn")

Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
2020-04-08 22:03:40 +02:00
Adrian Schmutzler
85aef6f627 ath79: fix MAC addresses for ethernet on ZyXEL NBG6716
MAC addresses of the ethernet devices (eth0 & eth1) are randomly set at
boot time by the ag71xx driver, because it is currently not possible to
retrieve MAC addresses in ASCII format within the DTS file.
This commit works around this behaviour by setting the MAC addresses
during the preinit phase.

The same has been implemented recently for the Siemens WS-AP3610 in
d2b8ccb1c0 ("ath79: add support for Siemens WS-AP3610").

MAC assignment in vendor firmware is as follows:

use   vendor   address     OpenWrt
2g    wifi0    ethaddr     -> wlan1
5g    wifi1    ethaddr +1  -> wlan0
lan   eth1     ethaddr +2  -> eth0
wan   eth0     ethaddr +3  -> eth1

ethaddr is retrieved by $(mtd_get_mac_ascii u-boot-env ethaddr)

Note that both Wifi and ethernet indexing is swapped in OpenWrt
compared to vendor firmware.

Suggested-by: Guillaume Lefebvre <guillaume@zelig.ch>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Kevin Gagnon <kevin_gagnon@videotron.ca>
2020-04-08 16:59:14 +02:00
Pawel Dembicki
c948a4782b ramips: add support for D-Link DWR-960
The DWR-960 Wireless Router is based on the MT7620A SoC.

Specification:

- MediaTek MT7620A (580 Mhz)
- 128 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7610 mpcie card)
- 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN)
- 1x 10/100/1000 Mbps Ethernet (1 LAN) (AR8035)
- 2x internal, non-detachable antennas (Wifi 2.4G)
- 3x external, detachable antennas (2x LTE, 1x Wifi 5G)
- 1x LTE modem
- UART (J4) header on PCB (57600 8n1)
- 9x LED, 2x button
- JBOOT bootloader

Known issues:
- Flash is extremely slow.

Installation:
Apply factory image via http web-gui or JBOOT recovery page

How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
  blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-04-08 14:05:51 +01:00
Pawel Dembicki
5410a8e295 ramips: mt7620: add rgmii delays support
At this moment mt7620 ethernet driver doesn't support rgmii delays
configuration. SoC MT7620 have bits 2 and 3 in GPC1 an GPC2 to configure
delays for rx and tx rgmii interface.

This patch adds rx/tx rgmii delay configuration from dts.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-04-08 13:57:50 +01:00
Pawel Dembicki
aff965a415 generic: backport Wistron Neweb D19Q1 patches
Backport patches which adds suport for the Wistron Neweb D19Q1 3G/4G modem,
used in D-Link DWR-960.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-04-08 13:57:50 +01:00
Adrian Schmutzler
f761f4052c ramips: mt7621: harmonize naming scheme for Mikrotik
So far, image/device/board names for Mikrotik devices in mt7621 have
been used quite inconsistently.

This patch harmonizes the naming scheme by applying the same style
as used lately in ath79, i.e. using "RouterBOARD" as separate word
in the model name (instead of RB prefix for the number) and deriving
the board/device name from that (= make lower case and replace spaces
by hyphens).

This style has already been used for most the model/DEVICE_MODEL
variables in mt7621, so this is essentially just adjusting the remaining
variables to that.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-08 13:46:30 +02:00
Tobias Schramm
48b4aab80c ramips: mt7621: reenable rbm11g
I have a rbm11g and can confirm that the LAN port is indeed
switch port 0.

Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
2020-04-08 13:42:58 +02:00
Tobias Schramm
57f4eab677 ramips: mt7621: add label mac address to rbm11g
The rbm11g has a label with printed on mac address similar to the
rbm33g.

Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
2020-04-08 13:42:09 +02:00
INAGAKI Hiroshi
e8787291b3 ramips: add support for Buffalo WSR-2533DHPL
Buffalo WSR-2533DHPL is a 2.4/5 GHz band 11ac router, based on MediaTek
MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 128 MiB
- Flash		: SPI-NOR 16 MiB
- WLAN		: 2.4/5 GHz 4T4R (2x MediaTek MT7615N)
- Ethernet	: 10/100/1000 Mbps
  - Switch	: MediaTek MT7530 (SoC)
- LED/keys	: 8x/6x (3x buttons, 2x slide-switches)
- UART		: through-hole on PCB
  - J4: 3.3V, GND, TX, RX from triangle-mark
  - 57600n8
- Power		: 12VDC 1.5A

Flash instruction using initramfs image:

1. prepare the TFTP server with the initramfs image renamed to
   "linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPL
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPL downloads
   the initramfs image and boot with it automatically
4. on the initramfs image, download the sysupgrade image to the device
   and perform sysupgrade with it
5. wait ~120 seconds to complete flashing

Switch position overview:

- slide-switch1 (2x positions)
  - "AUTO"
  - "MANUAL" (not connected to gpio)

- slide-switch2 (3x positions)
  - "ROUTER"
  - "AP" (not connected to gpio)
  - "WB"

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add note on switches, fix group->groups for state_default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-07 17:04:18 +02:00
Dan Haab
c459a6bf48 bcm53xx: add support for Luxul FullMAC WiFi devices
This prepares support for models XAP-1610 and XWR-3150. Flashing
requires using Luxul firmware version:
1) 8.1.0 or newer for XAP-1610
2) 6.4.0 or newer for XWR-3150
and uploading firmware using "Firmware Update" web UI page.

Signed-off-by: Dan Haab <dan.haab@legrand.com>
2020-04-07 15:27:52 +02:00
Chris Morgan
7daab62861 ath79: add support for Comfast CF-EW72
Specifications:
Qualcomm/Atheros QCA9531 + QCA9886
2x 10/100 Mbps Ethernet, with 48v PoE
2T2R 2.4 GHz, 802.11b/g/n
2T2R 5 GHz, 802.11a/n/ac
128MB RAM
16MB SPI Flash
4x LED (Always On Power, LAN, WAN, WLAN)

Flashing Instructions:
Original firmware is based on OpenWRT, so flashing the sysupgrade image on
the factory firmware is sufficient.

Tested: Reset button, WAN LED, LAN LED, Power LED (always on, not much
to test), WLAN LED (one LED only for 2 interfaces, by default it gets
assigned to the first interface), MAC addresses (match factory firmware).
My LAN factory MAC address ends in F2.

use	stock_mac	art_loc
lan	:f2		0x0
wan	:f3		0x1002
5g	:f4		0x6
2g	:f5		0x5006

Since MAC address flash locations do not really match their use in vendor
firmware (e.g. address from 5 GHz calibration data is assigned to 2.4 GHz
WiFi), just calculate the MAC addresses with an offset based on 0x0 address.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
[add MAC address comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-07 01:00:10 +02:00
Alex Lewontin
a0d1451088 ramips: harmonize Netgear R6120 DT LED node names
This changes the node names for the LEDs in the Netgear R6120
device-tree file to provide consistency with other devices.

Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-06 17:08:38 +02:00
Lim Guo Wei
bf9b742cd4 ath79: add support for TP-Link TL-MR3420 v3
This adds support for the TP-Link TL-MR3420 v3, a later revision of the
v2 with an external gpiochip similar to TP-Link Archer C7 v4.

Specifications:

SOC: Qualcomm Atheros QCA9531
CPU: 650MHz
Flash: 4 MiB
RAM: 32 MiB
WLAN: Qualcomm Atheros QCA9531 bgn 2T2R 2.4 GHz
Ethernet: 5 ports (100M)

Flashing instructions:

- Flash factory image from OEM WebUI:
  openwrt-ath79-tiny-tplink_tl-mr3420-v3-squashfs-factory.bin
- Sysupgrade from ath79 image:
  openwrt-ath79-tiny-tplink_tl-mr3420-v3-squashfs-sysupgrade.bin

Signed-off-by: Lim Guo Wei <limguowei@gmail.com>
[remove SUPPORTED devices, some typo adjustments, fix WAN MAC
address, fix sorting in 01_leds]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-06 11:55:24 +02:00
Adrian Schmutzler
c3083b9649 ipq806x: remove support for kernel 4.14
This target has been on kernel 4.19 for several months [1] and
already uses kernel 5.4 as testing kernel. Therefore, it should
not be necessary to keep support for kernel 4.14 as well.

[1] 2a82e0e1ca ("ipq806x: switch to 4.19 kernel version")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065/nbg6817]
2020-04-06 09:58:11 +02:00
Kip Porterfield
4b8d274456 ramips: add DTS triggers to USB LEDs for F9K1109v1
Alter DTS for Belkin F9K1109v1 to trigger USB leds from the echi/ochi
ports.

Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
2020-04-06 09:57:28 +02:00
John Crispin
86db1f69c4 mediatek: set v5.4 as default
Signed-off-by: John Crispin <john@phrozen.org>
2020-04-06 07:07:42 +02:00
John Crispin
8021652478 mediatek: add hw flow table offloading
Signed-off-by: John Crispin <john@phrozen.org>
2020-04-06 07:07:42 +02:00
John Crispin
af5a17dbb2 mediatek: add support for rtl8367c
Signed-off-by: John Crispin <john@phrozen.org>
2020-04-06 07:07:42 +02:00
John Crispin
08df22e2ab mediatek: drop v4.14 support
Signed-off-by: John Crispin <john@phrozen.org>
2020-04-06 07:07:42 +02:00
John Crispin
e2ceb8dd93 mediatek: more v5.4 fixes
These are all backports and/or on their way upstream.

Signed-off-by: John Crispin <john@phrozen.org>
2020-04-06 07:07:42 +02:00
John Crispin
beb9820ed3 mediatek: consolidate partition names and settings
Signed-off-by: John Crispin <john@phrozen.org>
2020-04-06 07:07:42 +02:00
John Crispin
bce39e1d00 mediatek: fix elecom board name
menuconfig was showing the the company name twice.

Signed-off-by: John Crispin <john@phrozen.org>
2020-04-06 07:07:42 +02:00
John Crispin
6786dc26a2 generic: fix flow table hw offload
Make the driver work with recent upstream changes.

Signed-off-by: John Crispin <john@phrozen.org>
2020-04-06 07:07:42 +02:00
Chuanhong Guo
95bd6a04b5 ramips: fix path for dma-ralink and mtk-hsdma
These two drivers were available in drivers/staging in 5.4.
Fix driver paths for them.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-05 18:16:17 +08:00
Chuanhong Guo
f0f35fdac1 Revert "generic: 5.4: Add 4B_OPCODES flag to w25q256"
This reverts commit d7f21940bc.

Winbond W25Q256FV and W25Q256JV both uses 0xef4019 as JEDEC ID,
but only the latter has proper 4B_OPCODES support.
W25Q256FV has all 4B read instructions but it lacks a 4B page program
instruction, causing the entire flash to be read-only.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-05 12:07:47 +08:00
Thibaut VARÈNE
fdac4c085d ath79: improve mikrotik-caldata.sh
Reduce unnecessary flash wear and be tidy:
- Run the extraction only if necessary
- Extract temporary file to /tmp
- cleanup after execution

Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-04-04 11:18:58 +01:00
INAGAKI Hiroshi
817e132332 kernel: rtl8367b: use id as a bit offset for BYPASS_LINE_RATE
In RTL8367B (RTL8367RB/RTL8367R-VB), the driver in GPL tars of the
devices with this switch directly uses the ID of external interface
as a bit offset.

We should use the same way.

ref (RTL8367B):
  - ASUS RT-N56U
  - TP-Link Archer C2 v1

ref (RTL8367):
  - TP-Link TL-WR2543ND v1

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2020-04-04 17:20:13 +08:00
INAGAKI Hiroshi
e714cf4195 kernel: rtl8367b: fix DEBUG register address for extif2
RTL8367B_CHIP_DEBUG1_REG (0x1304) is for external interface 1. For
external interface 2, use RTL8367B_CHIP_DEBUG2_REG (0x13e2) instead.

Fixes: 9801d61c4a ("kernel: rtl8367b: add configuration for extif2")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2020-04-04 16:55:47 +08:00
Chuanhong Guo
4d979a4d19 ramips: mt7621: bringup dsa master on preinit
DSA requires master netdev to be up before any of its slave ports.
Bring it up during preinit so that the first lan port can be used
on failsafe.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-04 16:30:16 +08:00
Chuanhong Guo
838f1fbb50 ramips: mt7621: disable image for mikrotik_rbm11g
It's unknown which switch port is used on mikrotik_rbm11g.
Disable this image until someone with actual device fixes this problem.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-04 15:25:36 +08:00
Chuanhong Guo
a8d62a4eb1 ramips: remove set_preinit_iface script
This script isn't suitable for mt7621 anymore due to switching to DSA
and it needs a different preinit script.
Generic preinit logic in package/base-files has the ability to parse
board.json and pick preinit iface accordingly. Just remove this script
instead of moving it into subtargets.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-04 14:56:14 +08:00
DENG Qingfang
764cc5c6a6 generic: mt7530: fix null pointer dereferencing in port5 setup
The 2nd gmac of mediatek soc ethernet may not be connected to a PHY
and a phy-handle isn't always available.
Unfortunately, mt7530 dsa driver assumes that the 2nd gmac is always
connected to switch port 5 and setup mt7530 according to phy address
of 2nd gmac node, causing null pointer dereferencing when phy-handle
isn't defined in dts.
This commit fix this setup code by checking return value of
of_parse_phandle before using it.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
3624721ef1 generic: backport support for MT7530 DSA port mirroring
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
René van Dorst
ae6b4d3f86 ramips: correct MTC WR1201 LAN ports names
LAN ports of MTC WR1201 are reversed, so correct their names

Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
10f27c6f00 ramips: mt7621: add new NAND driver
Add new NAND driver for MT7621

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
92daa06f22 ramips: mt7621: drop obsolete mx25l25635f dts hack
5.4 kernel has fixed this issue, so the hack is no longer needed.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
437aaae6ca Revert "ramips: mt7621: disable images for gehua_ghl-r-001"
This reverts commit 28080d54d2.
Support for MX25L25635F flash is fixed upstream

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
dcf7fdbdbf ramips: move swconfig to subtargets except for MT7621
As MT7621 does not use swconfig anymore, move the package swconfig to
other subtargets.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
6570960913 ramips: mt7621: introduce 'soc_device' initialization
mt7621 SoC has its own 'ralink_soc_info' structure with some
information about the soc itself. Pcie controller and pcie phy
drivers for this soc which are still in staging git tree make uses
of 'soc_device_attribute' looking for revision 'E2' in order to
know if reset lines are or not inverted. This way of doing things
seems to be necessary in order to make things clean and properly.
Hence, introduce this 'soc_device' to be able to properly use those
attributes in drivers. Also set 'data' pointer points to the struct
'ralink_soc_info' to be able to export also current soc information
using this mechanism.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
c24d6111f4 ramips: fix MikroTik 750Gr3 LAN ports names
They are labeled as LAN2..LAN5 instead of LAN1..LAN4

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
53b66248f4 ramips: use SoC I2C instead of bitbanged for Ubiquiti ER-X-SFP
The original idea of bitbanged I2C is to use i2c-gpio-custom
Since i2c-gpio-custom is no longer available on 5.4, use SoC I2C instead

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
5acd1ed0be ramips: mt7621: fix Ubiquiti ER-X ports names and MAC addresses
The name of each user port should be eth0..4, instead of lan1..4
and there is no WAN port. Rename them to match the official firmware.
To avoid conflict with the master port (gmac0), rename it to "dsa".

The official firmware assigns MAC address in this way:
eth0 = label mac
eth1 = label mac + 1
...
eth4 = label mac + 4

Since we have switched to DSA, it's possible to use different MAC for each port.

Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
3211c983fd ramips: mt7621: net-label support
Add support for renaming ethernet interfaces in DTS

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
1dce5c8a28 ramips: mt7621: switch kernel version to 5.4
After all dts and config changes, 4.14 no longer works on mt7621.
Switch it to 5.4 directly.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
c9f4f765c8 ramips: mt7621: change default ramips_setup_interfaces configuration
Most of MT7621 boards have LAN1~4 and WAN, so make this as the default

Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
d2b9461a55 ramips: mt7621 remove unused pinctrl groups in dts
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[split commit, remove leftover uart3->gpio setup]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-04 14:52:12 +08:00
DENG Qingfang
30644bc579 ramips: mt7621: update dts/defconfig for DSA
update dts and network/LED configuration for DSA driver.
sysupgrade from images prior to this commit with config preserved
will cause broken ethernet setup.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Acked-by: Jo-Philipp Wich <jo@mein.io>
[split commit]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-04 14:40:44 +08:00
DENG Qingfang
7bd19dbe99 ramips: mt7621: backport GPIO driver fix
Backport 2 patches from linux-next to fix mt7621 GPIO driver

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:14:43 +08:00
DENG Qingfang
9ebb85c372 ramips: mt7621: update PCIe node in dtsi
Update PCIe node in dtsi to match the new driver

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:14:43 +08:00
DENG Qingfang
d21d6ea454 ramips: mt7621: backport PCIe driver fixes from staging-test
Backport mt7621-pci/mt7621-pci-phy fixes from staging-test

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:14:43 +08:00
DENG Qingfang
66984646c2 ramips: mt7621: update pinctrl nodes
Upstream GPIO driver uses "groups" "function" properties

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:13:05 +08:00
DENG Qingfang
60f691dae4 ramips: mt7621: convert GPIO dts refs
The upstream driver does not use &gpio0..2 banks notation anymore,
so convert them to &gpio

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:13:05 +08:00
DENG Qingfang
783fc8e553 ramips: mt7621: replace gpio/eth nodes in mt7621.dtsi
There's different gpio and ethernet drivers upstream for mt7621.
Update these two nodes to match upstream dt bindings.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:10:58 +08:00
DENG Qingfang
99d210d6a0 ramips: mt7621: refresh kernel config
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 12:04:14 +08:00
DENG Qingfang
6be0da90a1 ramips: refresh patches
Removed upstreamed/solved elsewhere upstream:
- 0001-MIPS-ralink-Add-rt3352-SPI_CS1-pinmux.patch
- 0002-MIPS-pci-rt2880-set-pci-controller-of_node.patch
- 0004-MIPS-ralink-add-MT7621-pcie-driver.patch
- 0009-PCI-MIPS-enable-PCIe-on-MT7688.patch
- 0025-pinctrl-ralink-add-pinctrl-driver.patch
- 0028-GPIO-ralink-add-mt7621-gpio-controller.patch
- 0043-spi-add-mt7621-support.patch
- 0045-i2c-add-mt7621-driver.patch
- 0047-DMA-ralink-add-rt2880-dma-engine.patch
- 0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch
- 0054-mtd-spi-nor-w25q256-respect-default-mode.patch
- 0099-pci-mt7620.patch
- 304-spi-nor-enable-4B-opcodes-for-mx25l25635f.patch

Removed because of the new NAND driver:
- 0038-Revert-mtd-nand-Remove-unused-chip-write_page-hook.patch
- 0039-mtd-add-mt7621-nand-support.patch
- 0040-nand-hack.patch

Remove patch that no longer applies (needs rework):
- 0034-NET-multi-phy-support.patch

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 12:04:13 +08:00
DENG Qingfang
d75c9b8f81 ramips: mtk-mmc: set correct DMA mask
Since commit f8c55dc ("MIPS: use generic dma noncoherent ops for
simple noncoherent platforms") changed MIPS dma handling, the mmc
driver fails because it doesn't have a dma mask is set.

So set the correct dma mask.

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 12:04:13 +08:00
DENG Qingfang
d4903b5720 ramips: move MTK MMC driver to files directory
Move MTK MMC driver from "files-4.14" to "files" so kernel 5.4
can use it

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 12:04:13 +08:00
DENG Qingfang
c70545f397 ramips: copy patches and kernel config to 5.4
Copy patches and kernel config to 5.4 for ramips

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 12:04:13 +08:00
Rafał Miłecki
b51ea43f90 bcm53xx: refactor board.d code in 02_network
1. Use functions for cleaner code
2. Always execute WAN interface generic code

Before this change WAN interface code wasn't executed on all devices due
to an early "exit 0".

Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-04-03 17:59:56 +02:00
Tim Harvey
ff6b092121 imx6: bootscript: use partition UUID for rootfs if possible
Specifying root filesystem by device is non-deterministic for several
reasons:
 - USB device unmeration order is not garunteeed for USB storage devs
 - MMC devs ordering is determined by the instance of the MMC host
   controller including non-storage SDIO devices which can throw off
   numbering depending on kernel versions.

It is recommended to use partition UUID

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2020-04-03 12:17:45 +02:00
Tim Harvey
4298339b23 octeontx: switch to kernel 5.4
5.4 is stable on Gateworks Newport GW610x/GW620x/GW630x/GW640x

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2020-04-03 12:17:45 +02:00
Kevin Darbyshire-Bryant
b74386acc6 kmod-sched-cake: switch to in-tree cake for 4.19+
Use in tree version of cake for kernels 4.19+ and backport features from
later kernel versions to 4.19.

Unfortunately PROVIDES dependency handling produces bogus circular
dependency warnings so whilst this package and kmod-sched-cake-oot
should be able to PROVIDE kmod-sched-cake this doesn't work.

Instead, remove the PROVIDES option and modify package sqm-scripts to
depend on the correct module independently.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-04-01 21:59:45 +01:00
Daniel Golle
9f14216a2c oxnas: some improvements for Shuttle KD20
* install kmod-hwmon-drivetemp by default
 * wire up thermal zone
 * fix fan GPIO polarity
 * fix i2c-gpio GPIO_OPEN_DRAIN

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-03-31 21:41:23 +01:00
Daniel Golle
5e82e1ed2f oxnas: fix warning in SATA driver
drivers/ata/sata_oxnas.c: In function 'sata_oxnas_port_irq':
drivers/ata/sata_oxnas.c:2126:25: warning: left shift count >= width of type [-Wshift-count-overflow]
  if (ap->qc_active & (1 << ATA_TAG_INTERNAL)) {
                           ^~

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-03-31 21:30:57 +01:00