i2c_add_numbered_adapter is the wrong function to use here. It requires
setting nr to some value, otherwise it behaves the same as
i2c_add_adapter. nr is not set.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16825
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
What seems to be happening is that the kernel requests an ACTIVE_LOW
gpio initially and sets it to high later based on gpios in dts.
This seems to break some devices where the bootloader sets it to high.
Fixes: e612900ae0 ("ramips: mt7621: convert usb power to regulators")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16877
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Sophos AP15C uses the same hardware as the AP15, but has a reset button.
Based on:
commit 6f1efb2898 ("ath79: add support for Sophos AP100/AP55 family")
author Andrew Powers-Holmes <andrew@omnom.net>
Fri, 3 Sep 2021 15:53:57 +0200 (23:53 +1000)
committer Hauke Mehrtens <hauke@hauke-m.de>
Sat, 16 Apr 2022 16:59:29 +0200 (16:59 +0200)
Unique to AP15C:
- Reset button
- External RJ45 serial console port
Flashing instructions:
This firmware can be flashed either via a compatible Sophos SG or XG
firewall appliance, which does not require disassembling the device, or via
the U-Boot console available on the internal UART header.
To flash via XG appliance:
- Register on Sophos' website for a no-cost Home Use XG firewall license
- Download and install the XG software on a compatible PC or virtual
machine, complete initial appliance setup, and enable SSH console access
- Connect the target AP device to the XG appliance's LAN interface
- Approve the AP from the XG Web UI and wait until it shows as Active
(this can take 3-5 minutes)
- Connect to the XG appliance over SSH and access the Advanced Console
(Menu option 5, then menu option 3)
- Run `sudo awetool` and select the menu option to connect to an AP via
SSH. When prompted to enable SSH on the target AP, select Yes.
- Wait 2-3 minutes, then select the AP from the awetool menu again. This
will connect you to a root shell on the target AP.
- Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc
- Run `mtd -r write /tmp/openwrt.bin astaro_image`
- When complete, the access point will reboot to OpenWRT.
To flash via U-Boot serial console:
- Configure a TFTP server on your PC, and set IP address 192.168.99.8 with
netmask 255.255.255.0
- Copy the firmware .bin to the TFTP server and rename to 'uImage_AP15C'
- Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4]
- Connect the AP ethernet to your PC's ethernet port
- Connect a terminal to the UART at 115200 8/N/1 as usual
- Power on the AP and press a key to cancel autoboot when prompted
- Run the following commands at the U-Boot console:
- `tftpboot`
- `cp.b $fileaddr 0x9f070000 $filesize`
- `boot`
- The access point will boot to OpenWRT.
Signed-off-by: David Lutz <kpanic@hirnduenger.de>
IMAGE_SIZE was previously set to kernel1 + ubi size = 256768k, now
kernel1 is 6MB adjust this value to add 3072k to total image size.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Link: https://github.com/openwrt/openwrt/pull/15194
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Edgerouter-X factory images have not built automatically since 19.x due
to images being over 3MB. While it was possible to build custom images
with very stripped down config, this is no longer possible with the size
increases of linux 6.1 and 6.6.
Drop code for generation of factory images, if some dev later wishes to
try custom images they can revert this commit.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Link: https://github.com/openwrt/openwrt/pull/15194
Signed-off-by: Petr Štetiar <ynezz@true.cz>
With the new layout providing 6MB for kernel there will be no issues
with kernel size affecting build of images.
Re-enable image builds for Edgerouter-X and X-SFP.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Use compat version to indicate that the new layout for larger kernels
is in place. This handled by the patch to ubnt.sh to always select
the kernel1 slot for flashing and as active kernel slot.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Refer user to the wiki page for instructions on how to migrate to the
new kernel layout.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
Signed-off-by: Petr Štetiar <ynezz@true.cz>
With the updated partition layout set in dts, set the KERNEL_SIZE
parameter to 6MB allowing builds of Linux 6.1 and later to fit.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Uboot selects which kernel slot to boot based on a flag in the factory
mtd partition. Patch ubnt.sh to ensure always flash to kernel1 slot and
update flag if required.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The OEM layout for Edgerouter X provides for two 3MB kernel slots.
As of linux 6.1 the kernel images no longer fit and as such
Edgerouter X builds have been disabled in Main.
Revise the layout to make kernel1 slot 6MB and drop kernel2 slot.
This patch applies the required changes to the dts file.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The last "syscfg" partition of the OEM firmware turns out to be a
UBIFS used to store user data, just as the "rootfs_data" of OpenWrt,
so it should be reasonable to absorb it into the "ubi" partition.
Factory installations via either OEM firmware or tftp, or by forcibly
flashing factory image to mtd5 (firmware) partition with mtd tool are
confirmed working, but the UBI remaining inside "syscfg" partition
could break upgrade. Fortunately, installing kmod-mtd-rw and erasing
"syscfg" partition before upgrade is confirmed working, in which case,
"ubi" will automatically expand to the blank space once occupied by
the former mtd8 (syscfg), with the total block number increased, but
the UBIFS for rootfs_data will not automatically claim the newly
available space (since it is created when mtd8 still exists, and
sysupgrade does not set "autoresize" flag to rootfs_data). These space
will be claimed during the next upgrade, when rootfs_data is removed
and created again.
Fixes: 50f727b773 ("ath79: add support for Linksys EA4500 v3")
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/14791
Signed-off-by: Robert Marko <robimarko@gmail.com>
Mass production units will get 16 assigned MAC addresses. This allows each phy
to spawn up to 7 VAPs which will each have unique MAC without needing the
private bit.
Signed-off-by: John Crispin <john@phrozen.org>
Mass production units will get 16 assigned MAC addresses. This allows each phy
to spawn up to 7 VAPs which will each have unique MAC without needing the
private bit.
Signed-off-by: John Crispin <john@phrozen.org>
A factory image for DNA EX400 depends on an initramfs image and they
were explicitly removed from the imagebuilder recently. Now the factory
image creation fails miserably and it also affects custom image creation
with the firmware selector.
Add the initramfs kernel to the staging so that it's shipped with the
imagebuilder. Also remove a image build target added solely for DNA EX400.
Tested by creating a factory and syspupgrade images locally with
the imagebuilder and verified their functionality.
Related work
c85348d9ab ("imagebuilder: remove initramfs image files")
Fixes: fea2264d9f ("ramips: mt7621: Add DNA Valokuitu Plus EX400")
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
---
v4: use append-image-stage, remove Build/kernel-initramfs-bin
v3: adjust commit subject
v2: remove fix for inconsistent line ending elsewhere in the file
Link: https://github.com/openwrt/openwrt/pull/16659
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream stable is slow at picking this up and several systems
are regressing. Add the patch locally in OpenWrt.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Specifying GPIO_ACTIVE_HIGH on the GPIO for the voltage regulator doesn't
suffice. The regulator itself requires enable-active-high to be set.
Fixes: #16292
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Link: https://github.com/openwrt/openwrt/pull/16839
Signed-off-by: Robert Marko <robimarko@gmail.com>
No need for a custom function that does the same thing.
Oversight from devm conversion.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16748
Signed-off-by: Robert Marko <robimarko@gmail.com>
Oversight from devm conversion. No need for a custom static inline
function.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16747
Signed-off-by: Robert Marko <robimarko@gmail.com>
These things are regulators. Should silence dmesg messages about using
dummy regulators.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16804
Signed-off-by: Robert Marko <robimarko@gmail.com>
The mediatek target requires refreshing after recent additions.
Fixes: cfe8e6e75f ("mediatek: add support for Realtek RTL8261n 10G PHYs")
Fixes: ddfae94a14 ("mediatek: add support for swapping the polarity on usxgmii interfaces")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Assign pwm function of PWM0 pin to the pwm-fan.
This is mostly just cosmetics as it basically reflects the default
setting of that pin.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add additionals possible pinctrl group for pwm2~7 on pins
pin 4 (GPIO_A) pwm7
pin 58 (JTAG_JTDI) pwm2
pin 59 (JTAG_JTDO) pwm3
pin 60 (JTAG_JTMS) pwm4
pin 61 (JTAG_JTCLK) pwm5
pin 62 (JTAG_JTRST_N) pwm6
They can be useful e.g. on the BPi-R4 as in that way pwm2~6 can be exposed
on the 26-pin header (pwm6 always, pwm2~5 instead of the full UART).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Avoids having to call mutex_destroy in remove.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16755
Signed-off-by: Robert Marko <robimarko@gmail.com>
The clocks for SPI busses were named wrongly which resulted in the
spi-mt65xx driver not requesting them. This has apparently been
worked around by marking the clocks required for SPI0 which is used
for SPI-NOR and SPI-NAND flash chips as critical.
Fix the device tree for all 3 generic SPI host controllers and no
longer mark clocks as critical.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix in commit 25eead21c5 ("ath79: fix 5GHz on QCA9886 variant of ZTE MF286")
was incomplete. A user of such variant popped up, and in the boot log
after installation, we discovered that QCA9886 expects different
pre-calibration data size, than the older QCA9880 variant:
ath10k_pci 0000:00:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
ath10k_pci 0000:00:00.0: firmware ver 10.4b-ct-9888-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 59e741e7
ath10k_pci 0000:00:00.0: invalid calibration data length in nvmem-cell 'pre-calibration': 2116 != 12064
ath10k_pci 0000:00:00.0: Loading BDF type 0
ath10k_pci 0000:00:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0056,subsystem-vendor=0000,subsystem-device=0000 from ath10k/QCA9888/hw2.0/board-2.bin
ath10k_pci 0000:00:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9888/hw2.0
ath10k_pci 0000:00:00.0: failed to fetch board file: -12
ath10k_pci 0000:00:00.0: could not probe fw (-12)
Explicitly define a pre-calibration nvmem-cell for this variant, and use
it instead of the calibration one, which is shorter.
Fixes: 25eead21c5 ("ath79: fix 5GHz on QCA9886 variant of ZTE MF286")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16809
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The patches were generated from the RPi repo with the following command:
git format-patch v6.6.58..rpi-6.6.y
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
It should be debounce-interval, as with the others.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16802
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit ec8f647d16, as with the
current kernel version, the change actually causes the same bug it once
may have fixed -- that is, the leds are now again reversed.
I suspect this was due to a switch to a newer kernel version between when
the patch was submitted and now reversing the order of the interfaces, so
that eth0 / the LAN interface is also the interface used for PoE, and eth1
/ the WAN interface is the non-PoE interface.
Signed-off-by: Rafal Boni <rafal.boni@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16779
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop removal of firewall4 package for I2SE Duckbill device.
With OPKG the firewall4 package was installed anyway as it's a
dependency of luci-app-firewall and was silently installed again later
in such condition. Drop it to fix support for APK.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop removal of firewall4 package for Synology DS213j device.
With OPKG the firewall4 package was installed anyway as it's a
dependency of luci-app-firewall and was silently installed again later
in such condition. Drop it to fix support for APK.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
RouterBOOT v7 on NOR devices no longer accepts the YAFFS kernel ELF
method of booting. It will accept an NPK image named bootimage.
Adjust mtdsplit_minor to accept this second possible boot file name.
Use the conservative value of 127 for YAFFS max name length (used when
YAFFS compiled with unicode support) vs 255.
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Acked-by: Thibaut VARENE <hacks@slashdirt.org>
Link: https://github.com/openwrt/openwrt/pull/16780
Signed-off-by: Robert Marko <robimarko@gmail.com>
Introduced with Linux 6.7, in commit:
5c2f7727d437 ("mtd: mtdpart: check for subpartitions parsing result"),
when a parser returns an error, this will be passed up, and
consequently, all parent mtd partitions get torn down.
Adjust the MiNOR mtdsplit driver to only return an error if there is a
critical problem in reading from the mtd device or allocating memory.
Otherwise return 0 to indicate that no partitions were found.
Also add logging to indicate what went wrong.
This mtdsplit parser makes a very limited check of the first YAFFS
header. For example, this will not match expectations when initially booting
an initramfs image with OEM on MTD.
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Acked-by: Thibaut VARENE <hacks@slashdirt.org>
Link: https://github.com/openwrt/openwrt/pull/16780
Signed-off-by: Robert Marko <robimarko@gmail.com>
It does the same thing minus a few dmesg prints.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16788
Signed-off-by: Robert Marko <robimarko@gmail.com>
The WiFi chips are actually on PCIe1 and PCIe2, PCIe0 is empty. Fix the
assignment so that WiFi works properly again.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Link: https://github.com/openwrt/openwrt/pull/16807
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Drop limitation on depending on only armv8 for armsr target as those
module should support both 32 and 64 bits systems.
Only thunderx-net actually require 64 bit systems.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop fmc and fmc-eth-config package as they were never actually
submitted to openwrt mainline and they don't exist around.
They are probably part of NXP SDK and were added due to copy-paste
errors.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add the '~' prefix to package that needs to skip installation as they
are meta-package just to download and compile firmware package for the
final firmware.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop kmod-i2c-ralink from ASUS RP-AC56 as it was wrongly added. Such
kmod is not supported on mt7621 as i2c is handled by the mediatek driver
and not bay the ralink downstream one.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix wrong package device list that is trying to remove deprecated
packages. Replace with new variant where possible.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop ipq-wifi-teltonika_rutx from Teltonika RUTX50, the board file was
merged upstream but the ipq package was never dropped from
DEVICE_PACKAGES list.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
