Currently downstream tools like ASU lack information about kernel
version to find out the relevant kmod build folder on downloads server.
So lets fix it by providing a new `linux_kernel` JSON array which would
for the start provide Linux kernel version, revision and vermagic
information.
"linux_kernel": {
"release": "1",
"vermagic": "b57450c07d3a786158c3601fc5cee57d",
"version": "6.6.61"
},
Fixes: openwrt/openwrt#17036Fixes: efahl/owut#9
Co-developed-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17042
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c857145e03)
Add ubihealthd to the nand-utils package, auto-create UCI config for
each UBI device and launch the daemon on boot.
The default time interval between scrubbing a random PED is 120 seconds
which means that a fully used 128 MiB flash chip gets scrubbed in about
a day and a half. The interval can be adjusted in UCI using the
'interval' option.
Suggested-by: Rodrigo Balerdi <lanchon@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/16973
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 7e287b563a)
7330fa5 initd: mount /sys and /proc with MS_RELATIME
Fixes mounting /proc in unpriviledged user namespace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 1e8505ac4e)
Package kmod-drm-panel-mipi-dbi as well as modules it depends on in
order to support a wide range of MIPI DBI complaint SPI-connected
TFT panels.
See https://github.com/notro/panel-mipi-dbi/ for more information on
how to use specific panels.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 0a7b7ef27c)
Edgerouter X currently has its eth1 port on the switch missing since there
is a naming conflict currently.
So, as the root cause is mixing kernel support for DSA interfaces having
predictable names set via "label" property vs others having it assigned
dynamically lets avoid the conflict by using our own custom property as
suggested upstream [1].
So, add support via "openwrt,netdev-name" property and use it on ERX.
Fixes: 2a25c6ace8 ("ramips: get rid of downstream network device label patch")
Fixes: #15643
Link: https://github.com/openwrt/openwrt/pull/17062
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 5695267847)
Fixup capabilities parsing in iw output.
In addition to the normal capabilities iw now also outputs HE MAC, HE
PHY and EHT MAC and EHT PHY capabilities. Exclude them in the parsing.
The grep returns this with mac80211-hwsim:
```
root@OpenWrt:~# iw phy phy0 info | grep 'Capabilities:'
Capabilities: 0x107e
HE PHY Capabilities: (0x02bfce0000000000000000):
EHT PHY Capabilities: (0x7c0000feffff7f01):
HE PHY Capabilities: (0x02bfce0000000000000000):
EHT PHY Capabilities: (0x7c0000feffff7f01):
HE PHY Capabilities: (0x02bf000000000000000000):
Capabilities: 0x107e
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfc1f3ffeffff7f37):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfc1f3ffeffff7f37):
HE PHY Capabilities: (0x1cbf000000000000000000):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfefffffeffffff7f):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfefffffeffffff7f):
HE PHY Capabilities: (0x1cbf000000000000000000):
Capabilities: 0x107e
```
With busybox 1.36.1 the ht_cap_mask variable will be set to
-72057598332895361. With busybox 1.37.0 it will be set to -1.
Both values are wrong, after this change it will be set to 4222
(0x107E).
Link: https://github.com/openwrt/openwrt/pull/17043
(cherry picked from commit adf958c919)
Link: https://github.com/openwrt/openwrt/pull/17055
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This tool was build in the phase 2 build, there the TARGET dependencies
are probably not meat. Mark it as non shared to build it together with
the targets where this option is set.
Link: https://github.com/openwrt/openwrt/pull/16975
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit febe1db43d)
Link: https://github.com/openwrt/openwrt/pull/17055
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The label-mac does not match the one assigned to the ethernet interface.
Use the mac-address assigned to the wifi interface instead, as it
matches the one found on the device label.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b8b658bc0d)
Trying to use 'package_whatdepends' feature of the ImageBuilder with OPKG
will currently fail as OPKG does not support "list --depends" call at all,
it seems that this is a mixup from the original APK support commit.
So, lets restore 'package_whatdepends' support for OPKG by calling
"whatdepends -A" instead as we used to before APK support.
Fixes: d788ab376f ("build: add APK package build capabilities")
Link: https://github.com/openwrt/openwrt/pull/17022
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 52519a59a8)
The original set of stock partitions was kept in the TR4400 v2 port,
with the same partition numbers but their names prefixed with 'stock_'.
This allowed scripts (installation, back to stock, etc) to run on both
stock and OpenWrt firmware. But this triggers warnings in the device
tree compiler, as partitions of the old and new schemes overlap.
This commit fixes the dtc warnings by deleting the stock partitions,
also renumbering some of the remaining MTD partitions in the process.
Additionally, the 'fw_env' partition is set to read-only.
These changes can break existing scripts as well as user configurations
that utilize the 'extra' partition. Users wanting to run old scripts can
do so by reverting to the 23.05 series releases.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16958
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 8ec35a2a15)
The broadcom PHY driver only has to depend upon PTP_1588_CLOCK_OPTIONAL
if NETWORK_PHY_TIMESTAMPING is enabled. The PTP functionality is stubbed
in this case.
Reflect this circumstance in the dependence condition. This allows to
build the driver as a built-in module even if PTP is built as a module.
This is required to include the broadcom PHY module regardless of the
built-setting of the PTP subsystem. On ath79 (and probably more)
targets with Broadcom PHY, Gigabit operation is currently broken as the
PHY driver is only built as a module in case all kernel-packages are
built. Due to this circumstance, affected devices fall back to using the
generic PHY driver.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit cbce32e30c)
Sync patch with upstream version and tag them.
Minor changes done to Pinctrl patch to support older kernel.
Patch automatically refreshed with make target/linux/refresh.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a5d23e3aee)
The Sophos AP15C uses the same hardware as the AP15, but has a reset button.
Based on:
commit 6f1efb2898 ("ath79: add support for Sophos AP100/AP55 family")
author Andrew Powers-Holmes <andrew@omnom.net>
Fri, 3 Sep 2021 15:53:57 +0200 (23:53 +1000)
committer Hauke Mehrtens <hauke@hauke-m.de>
Sat, 16 Apr 2022 16:59:29 +0200 (16:59 +0200)
Unique to AP15C:
- Reset button
- External RJ45 serial console port
Flashing instructions:
This firmware can be flashed either via a compatible Sophos SG or XG
firewall appliance, which does not require disassembling the device, or via
the U-Boot console available on the internal UART header.
To flash via XG appliance:
- Register on Sophos' website for a no-cost Home Use XG firewall license
- Download and install the XG software on a compatible PC or virtual
machine, complete initial appliance setup, and enable SSH console access
- Connect the target AP device to the XG appliance's LAN interface
- Approve the AP from the XG Web UI and wait until it shows as Active
(this can take 3-5 minutes)
- Connect to the XG appliance over SSH and access the Advanced Console
(Menu option 5, then menu option 3)
- Run `sudo awetool` and select the menu option to connect to an AP via
SSH. When prompted to enable SSH on the target AP, select Yes.
- Wait 2-3 minutes, then select the AP from the awetool menu again. This
will connect you to a root shell on the target AP.
- Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc
- Run `mtd -r write /tmp/openwrt.bin astaro_image`
- When complete, the access point will reboot to OpenWRT.
To flash via U-Boot serial console:
- Configure a TFTP server on your PC, and set IP address 192.168.99.8 with
netmask 255.255.255.0
- Copy the firmware .bin to the TFTP server and rename to 'uImage_AP15C'
- Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4]
- Connect the AP ethernet to your PC's ethernet port
- Connect a terminal to the UART at 115200 8/N/1 as usual
- Power on the AP and press a key to cancel autoboot when prompted
- Run the following commands at the U-Boot console:
- `tftpboot`
- `cp.b $fileaddr 0x9f070000 $filesize`
- `boot`
- The access point will boot to OpenWRT.
Signed-off-by: David Lutz <kpanic@hirnduenger.de>
(cherry picked from commit a7abc7ec3b)
/sbin/pkg_check uses opkg and is not even packaged when using the
default opkg configuration. remove it when using apk too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 0ce237a20c)
8dfead68c202 wifi: mt76: mt7915: hold dev->mutex while interacting with the thermal state
d508a6eb935d wifi: mt76: mt7996: use mac80211 .sta_state op
57019e663f57 wifi: mt76: add code for emulating hardware scanning
dc4c2bdf7c56 wifi: mt76: add support for allocating a phy without hw
8cd0263f92e1 wifi: mt76: rename struct mt76_vif to mt76_vif_link
99df84d62883 wifi: mt76: add vif link specific data structure
dcc6f158d759 wifi: mt76: mt7996: split link specific data from struct mt7996_vif
d388deab9e73 wifi: mt76: initialize more wcid fields mt76_wcid_init
d026be405c54 wifi: mt76: add chanctx functions for multi-channel phy support
0b05795ca81c wifi: mt76: remove dev->wcid_phy_mask
0b526090de95 wifi: mt76: add multi-radio support to a few core hw ops
aeedee5c0a2c wifi: mt76: add multi-radio support to tx scheduling
fc0ff17b53ff wifi: mt76: add multi-radio support to scanning code
f19cbcf83400 wifi: mt76: add multi-radio remain_on_channel functions
42429ae0eaf6 wifi: mt76: mt7996: use emulated hardware scan support
f9d593d4a6b4 wifi: mt76: mt7996: pass wcid to mt7996_mcu_sta_hdr_trans_tlv
807090b28661 wifi: mt76: mt7996: prepare mt7996_mcu_add_dev/bss_info for MLO support
252baa7bf477 wifi: mt76: mt7996: prepare mt7996_mcu_add_beacon for MLO support
9ee990050305 wifi: mt76: mt7996: prepare mt7996_mcu_set_tx for MLO support
bf12cc404334 wifi: mt76: mt7996: prepare mt7996_mcu_set_timing for MLO support
60bf2bef95dc wifi: mt76: connac: prepare mt76_connac_mcu_sta_basic_tlv for MLO support
1289737e12a8 wifi: mt76: mt7996: prepare mt7996_mcu_update_bss_color for MLO support
7c00df0e7e57 wifi: mt76: connac: rework connac helpers
484e3f289a40 wifi: mt76: mt7996: move all debugfs files to the primary phy
d258f4e3e1ca wifi: mt76: mt7996: switch to single multi-radio wiphy
c246fa545119 wifi: mt76: mt7996: fix monitor mode
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 6720c4ccba)
e93f6c3fc729 main: fix format string related warnings for log/debug printf functions
6ab44a2413f9 fix signed/unsigned comparison warnings
4fe997b61d7d system-dummy: add system_if_apply_settings_after_up
992d33cb42a6 ubus: add notifications on wireless device state changes
34eb11eb6f5c device/interface: add "tags" attribute from config to status dump
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 5f68e24333)
This allows annotating wifi interfaces in the config in a way that can be
queried through wifi status. One example use case is to mark wifi interfaces
for use with specific services without having to explicitly reference the
(often unnamed) sections from elsewhere.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit a3ec35cadb)
This reverts commit e1043a746a, that
attempts to nest partitions that overlap but are not nested. This
causes the 'ubi' partition to be truncated, making rootfs inaccessible
and bricking the device.
Also, had this commit worked, it would have renumbered MTD partitions
in a way that would have broken documented scripts for installation and
update of main and recovery OSes, making backups, return to stock, etc,
and broken user configurations that put the 'extra' partition to use.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16944
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 0e59eaa796)
The last "syscfg" partition of the OEM firmware turns out to be a
UBIFS used to store user data, just as the "rootfs_data" of OpenWrt,
so it should be reasonable to absorb it into the "ubi" partition.
Factory installations via either OEM firmware or tftp, or by forcibly
flashing factory image to mtd5 (firmware) partition with mtd tool are
confirmed working, but the UBI remaining inside "syscfg" partition
could break upgrade. Fortunately, installing kmod-mtd-rw and erasing
"syscfg" partition before upgrade is confirmed working, in which case,
"ubi" will automatically expand to the blank space once occupied by
the former mtd8 (syscfg), with the total block number increased, but
the UBIFS for rootfs_data will not automatically claim the newly
available space (since it is created when mtd8 still exists, and
sysupgrade does not set "autoresize" flag to rootfs_data). These space
will be claimed during the next upgrade, when rootfs_data is removed
and created again.
Fixes: 50f727b773 ("ath79: add support for Linksys EA4500 v3")
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/14791
Signed-off-by: Robert Marko <robimarko@gmail.com>
109fa41b2321 system: fix description value from os-release
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 09a8b4920c)
Patches weren't refreshed when r8168 was updated to v8.054.00 in a85e18b53f.
Fixes: a85e18b53f ("kernel: r8168: update to v8.054.00")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 6490c88c75)
Mass production units will get 16 assigned MAC addresses. This allows each phy
to spawn up to 7 VAPs which will each have unique MAC without needing the
private bit.
Signed-off-by: John Crispin <john@phrozen.org>
Mass production units will get 16 assigned MAC addresses. This allows each phy
to spawn up to 7 VAPs which will each have unique MAC without needing the
private bit.
Signed-off-by: John Crispin <john@phrozen.org>
The mediatek target requires refreshing after recent additions.
Fixes: cfe8e6e75f ("mediatek: add support for Realtek RTL8261n 10G PHYs")
Fixes: ddfae94a14 ("mediatek: add support for swapping the polarity on usxgmii interfaces")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Assign pwm function of PWM0 pin to the pwm-fan.
This is mostly just cosmetics as it basically reflects the default
setting of that pin.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add additionals possible pinctrl group for pwm2~7 on pins
pin 4 (GPIO_A) pwm7
pin 58 (JTAG_JTDI) pwm2
pin 59 (JTAG_JTDO) pwm3
pin 60 (JTAG_JTMS) pwm4
pin 61 (JTAG_JTCLK) pwm5
pin 62 (JTAG_JTRST_N) pwm6
They can be useful e.g. on the BPi-R4 as in that way pwm2~6 can be exposed
on the 26-pin header (pwm6 always, pwm2~5 instead of the full UART).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Using the arrow keys to navigate the U-Boot menu often leads to being
dropped into the U-Boot shell unexpectedly.
This can be prevented in most cases by improving the logic to detect the
arrow key ESC sequence and only reprinting the menu if actually needed.
Also enable CONFIG_SERIAL_RX_BUFFER for all boards as it helps preventing
the remaining cases.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Mark the package as nonshared to build it in the target specific build
step 1 of the build bots instead of the architecture generic build step 2.
In the build step 2 it may be left out if we build it using a different
target.
Fixes: #16857
Link: https://github.com/openwrt/openwrt/pull/16859
Signed-off-by: Robert Marko <robimarko@gmail.com>
