Commit Graph

132 Commits

Author SHA1 Message Date
David Bentham
d8f4453bf2 mediatek: add Comfast CF-E393AX support
Comfast CF-E393AX is a dual-band Wi-Fi 6 POE ceiling mount access point.

Oem firmware is a custom openwrt 21.02 snapshot version.

We can gain access via ssh once we remove the root password.

Hardware specification:
  SoC: MediaTek MT7981A 2x A53
  Flash: 128 MB SPI-NAND
  RAM: 256MB DDR3
  Ethernet: 1x 10/100/1000 Mbps built-in PHY (WAN)
            1x 10/100/1000/2500 Mbps MaxLinear GPY211C (LAN)
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976D
  LEDS: 1x (Red, Blue and Green)
  Button: Reset
  UART: 3.3v, 115200n8
  --------------------------
  | Layout |
  | ----------------- |
  | 4 | VCC GND TX RX | <= |
  | ----------------- |
  --------------------------

Gain SSH access:
1. Login into web interface (http://apipaddress/computer/login.html),
   and download the
   configuration(http://apipaddress/computer/config.html).

2. Rename downloaded backup config - 'backup.file to backup.tar.gz',
   Enter 'fakeroot' command then decompress the configuration:
   tar -zxf backup.tar.gz

3. Edit 'etc/shadow', update (remove) root password:
   With password =
   'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
   'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
   to
   Without password =
   'root::0:99999:7:::'
   'root::0:99999:7:::'

4. Repack 'etc' directory back to a new backup file:
   tar -zcf backup-ssh.tar.gz etc/
5. Rename new config tar.gz file to 'backup-ssh.file'
   Exit fakeroot - 'exit'

6. Upload new configuration via web interface, now you
   can SSH with the following:

   'ssh -vv -o HostKeyAlgorithms=+ssh-rsa \
   -o PubkeyAcceptedAlgorithms=+ssh-rsa root@192.168.10.1'.

   Backup the mtd partitions
   - https://openwrt.org/docs/guide-user/installation/generic.backup

7. Copy openwrt factory firmware to the tmp folder to install via ssh:

   'scp -o HostKeyAlgorithms=+ssh-rsa \
   -o PubkeyAcceptedAlgorithms=+ssh-rsa \
   *-mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin \
   root@192.168.10.1:/tmp/'

   'sysupgrade -n -F \
   /tmp/*--mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin'

8. Once led has stopped flashing - Connect via ssh with the
   default openwrt ip address - 'ssh root@192.168.1.1'

9. SSH copy the openwrt sysupgrade firmware and upgrade
   as per the default instructions.

Signed-off-by: David Bentham <db260179@gmail.com>
2024-02-02 13:01:38 +01:00
Chuanhong Guo
1b7e62b20b mediatek: drop NMBM layout for Xiaomi WR30U
This reverts commit dcdcfc1511.

This is a firmware for third-party u-boot mod, which should not
be carried here by us.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2024-01-23 19:24:32 +08:00
Tianling Shen
c0c3234e17 mediatek: add support for JDCloud RE-CP-03
Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: 128GB eMMC
  RAM: 1GB DDR4
  Ethernet: 4x 1GbE, 1x 2.5GbE (RTL8221B)
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, Joylink
  Power: DC 12V 2A

Flash instructions:
1. Download and flash the vendor migration firmware via webUI:
   https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7986-jdcloud_re-cp-03-vendor-migration.bin
   (Default address is 192.168.68.1, user root, no password)
2. After device has booted up, write new GPT table:
   dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
   echo 0 > /sys/block/mmcblk0boot0/force_ro
   dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
   dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
   IP 192.168.1.254/24, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-01-19 21:43:32 +01:00
Thomas Schröder
4d7bac1dca
mediatek: GL-MT6000: Change LED colors
Fine tuning PR: openwrt/openwrt#14355 Ref: 5a82bb909b
("mediatek: GL-MT6000: Add missing LED state definitions")

As the only LED is using white in the stock firmware when the device is
running and blue for the bootloader I suggest following changes:
 - Using blue for the BL and preinit+failsafe
 - White for normal operation (like the original FW) and sysupgrade

With this changes it's clear by looking to the LED in which operation
mode the device is and a possible BL stuck can be seen easily.

Tested with [GL-MT6000](https://openwrt.org/toh/gl.inet/gl-mt6000).

Signed-off-by: Thomas Schröder <tschroeder_github@outlook.com>
Tested-by: Hannu Nyman <hannu.nyman@iki.fi>
2024-01-15 17:21:29 +01:00
Chukun Pan
8632f6184b mediatek: fixes typo for spi properties
Same as commit 3674689, correct 'buswidth' to 'bus-width'.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2024-01-14 23:11:57 +00:00
Chukun Pan
cfee7fa366 mediatek: YunCore AX835: convert to nvmem-layout
The nvmem-cells is deprecated. Also simplify mac address settings.

Fixes: b4086f4 ("mediatek: add support for YunCore AX835")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2024-01-14 23:11:57 +00:00
Chukun Pan
99bc8a9770 mediatek: Cudy WR3000: simplify mac address setup
The mac address of the network port under the switch is
the same as the corresponding gmac by default, so there
is no need to repeat the setting. Compile test only.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2024-01-14 23:11:57 +00:00
Chukun Pan
d555177960 mediatek: Cetron CT3003: move mac address setup to dts
It looks like we can put the mac address setting
into the device tree. Compile test only.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2024-01-14 23:11:57 +00:00
Felix Fietkau
50416c18dd mediatek: disable btif for mt7622 devices
It breaks built-in SoC WLAN. Can be re-enabled after we've figured out the cause

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-01-09 11:06:24 +01:00
Leon M. Busch-George
b4086f44cd mediatek: add support for YunCore AX835
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: 16MB NOR
  RAM: 256MB
  Ethernet: 2x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset
  Power: DC 12V 1A, PoE 802.3af 48V

Flash instructions:

Option #1 - SSH

  I was able to SSH into the stock firmware of my device.

  1. Attach the router to the network
  2. Use scp (-O) to copy the sysupgrade image
  3. Connect using SSH and run `sysupgrade -n`

Option #2 - U-Boot

  One way to use the bootloader for flashing is using TFTP:

  1. Connect to the router using an ethernet cable
  2  Spin up a TFTP server serving the sysupgrade file
  3. Open the case and attach a UART
  4. Attach power to the router and interrupt the countdown by pressing
     any key
  5. Select option #2 (Upgrade firmware)
  6. Enter IP address information and image name
  7. Wait patiently

Co-Authored-By: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net>
Co-Authored-By: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
2024-01-09 00:27:23 +01:00
Hannu Nyman
5a82bb909b mediatek: GL-MT6000: Add missing LED state definitions
Adjust LED names and provide the OpenWrt status indicator aliases
to actually use LEDs by the OpenWrt boot & sysupgrade processes.

* Name both LEDs clearly by the color
* Add the missing OpenWrt LED status indicator aliases and
  remove the now unnecessary default status from blue LED

After this commit, the LEDs are used as:

* bootloader, really early Linux boot: blue LED is on
* preinit/failsafe: white LED blinks rapidly
* late boot: white LED blinks slowly
* boot completed, running normally: blue LED is on

* sysupgrade: white LED blinks

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2024-01-09 00:03:07 +01:00
Dim Fish
7dbcc1215a mediatek: filogic: add support for Xiaomi AX3000T
**SoC**: MediaTek MT7981B 2x A53
  **Flash**: ESMT F50L1G41LB 128MB
  **RAM**: NT52B128M16JR-FL 256MB
  **Ethernet**: 4x 10/100/1000 Mbps
  **Switch**: MediaTek MT7531AE
  **WiFi**: MediaTek MT7976C
  **Buttons**: Reset, Mesh
  **Power**: DC 12V 1A

1. Get ssh access. Supported stock firmware **1.0.47**
   ```
   curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20set%20ssh_en%3D1%0A"
   curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20commit%0A"
   curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Ased%20-i%20's%2Fchannel%3D.*%2Fchannel%3D%22debug%22%2Fg'%20%2Fetc%2Finit.d%2Fdropbear%0A"
   curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0A%2Fetc%2Finit.d%2Fdropbear%20start%0A"
   curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=********/api/misystem/arn_switch" -d "open=1&model=1&level=%0Apasswd%20-d%20root%0A
   ```

2. Backup stock partitions
   ```
   nanddump -f /tmp/BL2.bin /dev/mtd1
   nanddump -f /tmp/Nvram.bin /dev/mtd2
   nanddump -f /tmp/Bdata.bin /dev/mtd3
   nanddump -f /tmp/Factory.bin /dev/mtd4
   nanddump -f /tmp/FIP.bin /dev/mtd5
   nanddump -f /tmp/ubi.bin /dev/mtd8
   nanddump -f /tmp/KF.bin /dev/mtd12
   ```
   Then transfer them to your computer in a safe place.

3. Get firmware information `cat /proc/cmdline`

4. Copy openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi to **/tmp** and flash
   If **firmware=0**
   ```
   ubiformat /dev/mtd9 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi
   nvram set boot_wait=on
   nvram set uart_en=1
   nvram set flag_boot_rootfs=1
   nvram set flag_last_success=1
   nvram set flag_boot_success=1
   nvram set flag_try_sys1_failed=0
   nvram set flag_try_sys2_failed=0
   nvram commit
   reboot
   ```
   If **firmware=1**
   ```
   ubiformat /dev/mtd8 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi
   nvram set boot_wait=on
   nvram set uart_en=1
   nvram set flag_boot_rootfs=0
   nvram set flag_last_success=0
   nvram set flag_boot_success=1
   nvram set flag_try_sys1_failed=0
   nvram set flag_try_sys2_failed=0
   nvram commit
   reboot
   ```

   Then reboot your router, it should boot to the OpenWrt initramfs system now.

5. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin
   `sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin`

1. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb
   `ubiformat /dev/mtd8 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb`

   `reboot`

2. Install kmod-mtd-rw
   `opkg update && opkg install kmod-mtd-rw`

   `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1`

3. Format ubi and create new ubootenv volume
   ```
   ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8
   ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
   ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
   ```

4. *(Optional **-10Mb** free space) Add recovery boot feature.*
   ```
   ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
   ubiupdatevol /dev/ubi0_2 /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb
   ```

5. Flash Openwrt U-Boot
   ```
   mtd write /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-preloader.bin BL2
   mtd write /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-bl31-uboot.fip FIP
   ```

6. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-squashfs-sysupgrade.itb
   `sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-squashfs-sysupgrade.itb`

1. Force flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb
   `sysupgrade -F -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb`

2. Format ubi and Nvram
   ```
   ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8
   mtd erase Nvram
   ```

3. Install kmod-mtd-rw
   `opkg update && opkg install kmod-mtd-rw`

   `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1`

4. Flash stock images from backup
   ```
   mtd write /tmp/BL2.bin BL2
   mtd write /tmp/FIP.bin FIP
   mtd write /tmp/ubi.bin ubi
   ```
   Then reboot your router, waiting it finished rollback in minutes.

   `ubiformat /dev/mtd7 -y -f /tmp/ubi.bin`
   Then reboot your router, waiting it finished rollback in minutes.

Signed-off-by: Dim Fish <dimfish@gmail.com>
2024-01-06 17:51:11 +01:00
Mikhail Zhilkin
bcdab30467 mediatek: MERCUSYS MR90X v1: remove deprecated led "label" properties
This commit:
1. Removes deprecated "label" property from the dts leds subnnodes;
2. Updates "01_leds" script.

Link: https://www.kernel.org/doc/Documentation/devicetree/bindings/leds/common.yaml
Link: https://www.kernel.org/doc/Documentation/devicetree/bindings/leds/leds-gpio.yaml

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2024-01-06 00:46:15 +01:00
Roland Reinl
fdb87a91b4 mediatek: Add support for D-Link EAGLE PRO AI R32
R32 is like the M32 part of the EAGLE PRO AI series from D-Link.

Specification:
 - MT7622BV SoC with 2.4GHz wifi
 - MT7975AN + MT7915AN for 5GHz
 - MT7531BE Switch
 - 512MB RAM
 - 128 MB flash
 - 2 LEDs (Status and Internet, both can be either orange or white)
 - 2 buttons (WPS and Reset)

Compared to M32, the R32 has the following differences:
 - 4 LAN ports instead of 2
 - The recory image starts with DLK6E6015001 instaed of DLK6E6010001
 - Individual LEDs for power and internet
 - MAC address is stored at another offset in the ODM partition

MAC addresses:
 - WAN MAC is stored in partition "Odm" at offset 0x81
 - LAN (as printed on the device) is WAN MAC + 1
 - WLAN MAC (2.4 GHz) is WAN MAC + 2
 - WLAN MAC (5GHz) is WAN MAC + 3

Flashing via Recovery Web Interface:
 - Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
 - Press the reset button while powering on the deivce
 - Keep the reset button pressed until the internet LED blinks fast
 - Open a Chromium based and goto http://192.168.0.1
 - Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-recovery.bin

Flashing via uBoot:
 - Open the case, connect to the UART console
 - Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
 - Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-initramfs-kernel.bin.
 - You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
 - Power on the device and select "1. System Load Linux to SDRAM via TFTP." in the boot menu
 - Enter image file, tftp server IP and device IP (if they differ from the default).
 - TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
 - The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
 - Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later
 - Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-squashfs-sysupgrade.bin
 - Reboot the device. OpenWrt should start from flash now

Revert back to stock using the Recovery Web Interface:
 - Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
 - Press the reset button while powering on the deivce
 - Keep the reset button pressed until the internet LED blinks fast
 - Open a Chromium based and goto http://192.168.0.1
 - Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.

Decrypting a D-Link firmware image:
 - Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
 - Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
 - Run ./m32-firmware-util R32 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
 - Example for firmware R32A1_FW103B01: ./m32-firmware-util R32 --DecryptFactoryImage R32A1_FW103B01.bin R32A1_FW103B01.decrypted.bin

Revert back to stock using uBoot:
 - Open the case, connect to the UART console
 - Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
 - Run a tftp server which provides the previously created backup of the Kernel1 partition.
 - You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
 - Power on the device and select "2. System Load Linux Kernel then write to Flash via TFTP." in the boot menu
 - Enter image file, tftp server IP and device IP (if they differ from the default).
 - TFTP download to FLASH will start. After a few seconds the stock firmware should start again

There is also an image openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-tftp.bin which can directly be flashed via U-Boot and TFTP.
It can be used if no backup of the Kernel1 partition is reuqired.

Flahsing via OEM web interface is currently not possible, the OEM images are encrypted. Creating images is only possible manually at the moment.
The support for the M32/R32 already includes support for flashing from the OEM web interface:
 - The device tree contains both partitions (Kernel1 and Kernel2) with conditions to select the correct one based on the kernel command line
 - The U-Boot variable "boot_part" is set accordingly during startup to finish the partition swap after flashing from the OEM web interface
 - OpenWrt sysupgrade flashing always uses the partition where it was initially flashed to (no partition swap)

Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
2024-01-02 21:22:46 +01:00
Patryk Kowalczyk
b22539b5fe mediatek: filogic: Asus TUF AX6000 fix inverted LED for 2.5Gb LAN port
Router Asus TUF AX6000 have second MaxLinear GPY211 PHY controller for 2.5Gb LAN port.
The 5'th LAN port have inverted status of the LED.
Based on the commit from main branch 90fbec8 we could set proper status of the LED.

Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
2024-01-02 19:14:54 +01:00
Xavier Franquet
782eb05008 mediatek: filogic: add support ASUS RT-AX59U
(based on support for ASUS RT-AX59U by liushiyou006)

SOC: MediaTek MT7986
RAM: 512MB DDR4
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)

Upgrade from AsusWRT to OpenWRT using UART

    Download the OpenWrt initramfs image.
    Copy the image to a TFTP server reachable at 192.168.1.70/24. Rename the image to rtax59u.bin.

    Connect the PC with TFTP server to the RT-AX59U.
    Set a static ip on the ethernet interface of your PC.
    (ip address: 192.168.1.70, subnet mask:255.255.255.0)
    Conect to the serial console, interrupt the autoboot process by pressing '4' when prompted.

    Download & Boot the OpenWrt initramfs image.

    $ setenv ipaddr 192.168.1.1
    $ setenv serverip 192.168.1.70
    $ tftpboot 0x46000000 rtax59u.bin
    $ bootm 0x46000000

    Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade.

    $ sysupgrade -n <path-to-sysupgrade.bin>

Upgrade from AsusWRT to OpenWRT using WebUI

    Download transit TRX file from https://drive.google.com/drive/folders/1A20QdjK7Udagu31FSszpWAk8-cGlCwsq

    Upgrade firmware from WebUI (192.168.50.1) using downloaded TRX file

    Wait for OpenWRT to boot (192.168.1.1).

    Upgrade system with sysupgrade image using luci or uploading it through scp and executing sysupgrade command

MAC Address for WLAN 5g is not following the same algorithm as in AsusWRT.
We have increased by one the WLAN 5g to avoid collisions with other networks from WLAN 2g
when bit 28 is already set.

              : Stock             : OpenWrt
  WLAN 2g (1) : C8:xx:xx:0D:xx:D4 : C8:xx:xx:0D:xx:D4
  WLAN 2g (2) :                   : CA:xx:xx:0D:xx:D4
  WLAN 2g (3) :                   : CE:xx:xx:0D:xx:D4
  WLAN 5g (1) : CA:xx:xx:1D:xx:D4 : CA:xx:xx:1D:xx:D5
  WLAN 5g (2) :                   : CE:xx:xx:1D:xx:D5
  WLAN 5g (3) :                   : C2:xx:xx:1D:xx:D5

  WLAN 2g (1) : 08:xx:xx:76:xx:BE : 08:xx:xx:76:xx:BE
  WLAN 2g (2) :                   : 0A:xx:xx:76:xx:BE
  WLAN 2g (3) :                   : 0E:xx:xx:76:xx:BE
  WLAN 5g (1) : 0A:xx:xx:76:xx:BE : 0A:xx:xx:76:xx:BF
  WLAN 5g (2) :                   : 0E:xx:xx:76:xx:BF
  WLAN 5g (3) :                   : 02:xx:xx:76:xx:BF

Signed-off-by: Xavier Franquet <xavier@franquet.es>
2023-12-31 00:03:24 +01:00
Mikhail Zhilkin
485adc9d3c mediatek: add support for Routerich AX3000
This PR is continuation of work under "mediatek: add support for Routerich
AX3000" #13703 by the agreement with PR #13703 original author (Maximilian
Weinmann <x1@disroot.org>). All reviews from the previous PR were taken
into into account.

Routerich AX3000 is a wireless WiFi 6 router.

Specification
-------------
- SoC       : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz
- RAM       : DDR3 256 MiB (ESMT M15T2G16128A)
- Flash     : SPI-NAND 128 MiB (ESMT F50L1G41LB)
- WLAN      : MediaTek MT7976CN dual-band WiFi 6
  - 2.4 GHz : b/g/n/ax, MIMO 2x2
  - 5 GHz   : a/n/ac/ax, MIMO 2x2
- Ethernet  : 10/100/1000 Mbps x4 (MediaTek MT7531AE)
- USB       : 1x 2.0
- UART      : through-hole on PCB
  - [J500] GND, TX, RX, 3.3V (115200n8)
- Buttons   : Mesh, Reset
- LEDs      : 1x Power (Blue)
              1x WiFi 2.4 GHz (Blue)
              1x WiFi 5 GHz (Red)
              1x Mesh (Blue)
              3x LAN activity (Blue)
              1x WAN activity (Blue)
              2x WAN no-internet (Red)
- Power     : 12 VDC, 1.5 A

Installation
------------
Flash OpenWrt 'sysupgrade.bin' image using stock firmware web-interface
(without keeping settings).

Return to stock
---------------
Install stock firmware image (without keeping settings) using OpenWrt
sysupgrade method.

Recovery
--------
Connect uart, use u-boot menu to flash stock firmware image or boot
OpenWrt initramfs image.

MAC addresses
-------------
+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| WAN     | 24:0f:5e:xx:xx:b4 | label     |
| LAN     | 24:0f:5e:xx:xx:b5 | label+1   |
| WLAN 2g | 24:0f:5e:xx:xx:b6 | label+2   |
| WLAN 5g | 24:0f:5e:xx:xx:b7 | label+3   |
+---------+-------------------+-----------+
The WLAN 2g MAC was found in 'Factory', 0x4

Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-12-26 17:17:23 +01:00
Ian Oderon
4300bc6688 mediatek: add support for Zbtlink ZBT-Z8103AX
Specifications:
SoC: MediaTek MT7981B
RAM: 256MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 3 LAN (Gigabit)
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND

No. of Antennas: 6
Note: Upon opening the router, only 5 antennas were connected
to the mainboard.

Led Layout:
Power-Mesh-5gwifi-WAN-LAN3-LAN2-LAN1-2gWiFi

Buttons:
Reset-Mesh

Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware

B. Through TFTP
Standard installation via UART:

1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.

Signed-off-by: Ian Oderon <ianoderon@gmail.com>
2023-12-26 00:02:19 +01:00
Daniel Golle
3aa686f8d4 mediatek: add support for Adtran SmartRG Bonanza Peak series
The Bonanza Peak series are a couple of MT7986-powered 2.5 GBit/s
Wi-Fi 6 residential gateway, access point and mesh router products.

All of them come with an eMMC to boot from, are powered via USB-C and
got a USB 3.0 type-A port. All of them got a Dialog (Renesas) DA14531
Bluetooth module connected via UART. If the device was previously
running stock firmware, the BT chip's internal flash has been loaded
with firmware and it can be attached using hciattach when using
OpenWrt.

SOC: MediaTek MT7986A
RAM: 2 GiB DDR4
eMMC: 8 GiB
Bluetooth: BLE5 (DA14531)
Serial: 3.3V level, 115200 8n1 on 4-pin connector

 * SDG-8612 - Dual-band RJ-45 gateway
   2x 2.5G MaxLinear PHY for WAN port
   3x 1GE LAN ports via MT7531 switch

 * SDG-8614 - Dual-band SFP gateway
   1x SFP cage with up to 2.5G speed
   1x 2.5G MaxLinear PHY for LAN port
   3x 1GE LAN ports via MT7531 switch

 * SDG-8622 - Tri-band mesh router
   2x 2.5G MaxLinear PHY
   The MT7986 2G and 5G are used as 2G and 5G high band.
   There’s a MT7915 PCIe card for 5G low band.

 * SDG-8632 - Tri-band mesh router with 6 GHz
   2x 2.5G MaxLinear PHY
   The MT7986 serves the 2G and 6G bands.
   There’s a MT7915 PCIe card for 5G.

Installation via U-Boot serial console:
0. setup TFTP server with IP 192.168.1.10/24, place initramfs image
renamed to openwrt.XXX where XXX is the internal product number:
 SDG-8612: XXX = 412
 SDG-8614: XXX = 414
 SDG-8622: XXX = 422
 SDG-8632: XXX = 432

1. connect to the serial console and power on the device.
   Interrupt the bootloader by pressing 'st'
2. setenv boot_mode openwrt ; saveenv
3. run boot1
   Load firmware via TFTP and write to flash
4. run boot2
   Now OpenWrt initramfs should boot
5. upload sysupgrade.bin via scp to /tmp
6. sysupgrade

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-12-10 06:22:51 +00:00
Luis Mita
b1fd4b35bf mediatek: add SPDX header for Confiabits MT7981 DTS
Fixing ambiguous licensing.

Signed-off-by: Luis Mita <luis@luismita.com>
2023-12-06 22:11:03 +01:00
Rafał Miłecki
07765f28b7 mediatek: filogic: add Acelink EW-7886CAX support
Acelink EW-7886CAX is an MT7986A (AKA Filogic 830) based access point.
It has 512 MiB of RAM, one 2.5 Gbps PoE (802.3at) Ethernet port and
on-SoC Wi-Fi. There is no printed MAC label (on my unit).

My unit came with Mediatek's firmware (based on OpenWrt 21.02)
installed. It was possible to simply upgrade using OpenWrt's sysupgrade
tool.

Another verified upgrade method is using U-Boot (requires UART). During
every boot there is "U-Boot Boot Menu". Selecting option "2. Upgrade
firmware" allows using U-Boot's tftp client to load and flash factory
image.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-12-05 09:06:47 +01:00
Luis Mita
2af07eb853 mediatek: add support for Confiabits MT7981
Confiabits MT7981 is a Wi-Fi 6 router based on MediaTek MT7981.

Specification:
 - SoC: MediaTek MT7981B
 - CPU: 2x 1.3 GHz Cortex-A53
 - Flash: 128 MiB SPI NAND
 - RAM: 256 MiB
 - WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
 - Ethernet: 4x 10/100/1000 Mbps MT7531AE (3xLAN, 1xWAN)
 - USB 2.0 port
 - Buttons: 1 Reset button, 1 Mesh button.
 - LEDs: 7x light-blue, 2x warm-white
 - Serial console: internal 4-pin header, 115200 8n1
 - Power: 12 VDC, 1.5 A

MAC addresses in stock firmware and in this commit:
+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| WAN     | 00:0c:43:xx:xx:e1 | label+1   |
| LAN     | 00:0c:43:xx:xx:e0 | label     |
| WLAN 2g | 00:0c:43:xx:xx:e0 | label     |
| WLAN 5g | 02:0c:43:xx:xx:e0 |           |
+---------+-------------------+-----------+
The label MAC was found in 'Factory', 0x4

Installation:
The stock firmware is OpenWrt-based. If you can reach LuCI or SSH, just use the sysupgrade image
with the 'Keep settings' option turned off.

Signed-off-by: Luis Mita <luis@luismita.com>
2023-11-29 23:52:14 +01:00
David Bauer
1239668648 mediatek: add support for GL.iNet GL-MT2500
Hardware
--------
SoC:  MediaTek MT7981BA
RAM:  1GB DDR4 (NANYA NT5AD512M16C4-JR)
MMC:  8GB eMMC (Samsung 8GTF4R)
ETH:  1000Base-T LAN (ePHY)
      2500Base-T WAN (MaxLinear GPY211C)
BTN:  1x Reset Button
LED:  System (blue/white)
      VPN (white)
USB:  1x USB-A (USB 3.0)
UART: 115200 8N1 - Pinout on board next to LAN port
      Don't connect 3.3V!

Known Issues
------------
U-Boot vendor recovery does not seem to accept any images, neither
GL.iNet images nor OpenWrt images. Recovery requires serial access!

Installation
------------
Upload the OpenWrt sysupgrade image to the Gl.iNet Web-UI. Make sure to
not retain existing settings.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-11-27 08:02:41 +01:00
Rosen Penev
3eb899fd36
mediatek: use mac-base
mac-address-increment is deprecated.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:45:26 +01:00
Rosen Penev
405bc5be13
mediatek: convert to nvmem-layout
Will allow removing mac-address-increment.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:45:26 +01:00
Chukun Pan
1be6347b7d
mediatek: Cetron CT3003: fixes typo for spi properties
Same as commit 3674689, correct 'buswidth' to 'bus-width'.
Also move the nmbm properties outside the partition definition.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-11-25 23:16:34 +01:00
Valerio 'ftp21' Mancini
b5df398a36 mediatek: add Zyxel EX5601-T0 with uboot custom partition
The flash procedure is similar to the Xiaomi AX6000 router.

Load openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb from original Zyxel U-Boot:

tftpboot openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb
bootm 0x46000000
Load mtd-rw
insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1

Format ubi and create ubootenv partitions

ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
Copy openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb to /tmp and create recovery partition.
If your recovery image is larger than 10MiB, size the recovery partition accordingly to make it fit.

ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
ubiupdatevol /dev/ubi0_2  openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb
Copy preloader and uboot to /tmp and write them in the mtd

mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-preloader.bin bl2
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-bl31-uboot.fip fip
Now write the firmware:
sysupgrade -n  /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-squashfs-sysupgrade.itb

To create a correct BL2, I had to add a profile for 'spim:4k+256' as I could not find a way to value the variable 'NAND_TYPE'.

Features and fixes from hitech95 tree has been squashed, I'm attaching his commit message:

The Power LED was not working correctly and not reacting
 to the boot process and statuses.

The board has space (footprint) for an unpopulated Zigbee chip,
 while we dont know the device model having this chip populated
 we have to assure that the common dts doesnt enable
 interfaces that share pins with such device.

In this instance the PCIe and the uart1 and uart2 are disabled.
Some of the control PCIE pins seems to be used for the Zigbee chip,
 UART1 seems to be used as a flash port while UART2 should be the
 main comunication interface of Zigbee chip.

The Zigbee chip should be a EFR32MG21. But the pins used for UART
 seems to be not on standard PINS used by other adapters.
 So it cannot run firmwares shared on the web.
 But it should be possible to build a custom firmware with
 the corrtect pinmux.

This commit also contains the following squashed commit from hitech95
 - mediatek: fix sysupgrade for Zyxel EX7601-T0 ubootmod

Changes and fixes added in common board:
 - added aliases for boot status leds.
 - added aliases for the mac-label-device.
 - added pin claims for core features (MDIO and UART 0)
 - added default LEDs configuration (01_leds)
 - added default network configuration (02_network)
 - added missing kmod-usb3 module for USB3
 - fixed LED names
 - fixed reset pin for SLIC chip
 - removed unused pinmux configurations and devices
 - fix LAN (switch) port numbering
 - using nvmem cells for wifi eeprom, dropping deprecated "mediatek,mtd-eeprom"
 - proper factory partition and mac address handling
 - cleaned up spi_nand sections and partition

Changes and fixxes added in stock layout:
 - added NMBM, if u-boot has it, the kernel must be informed.

Co-authored-by: Nicolò Veronese <nicveronese@gmail.com>
Co-developed-by: Nicolò Veronese <nicveronese@gmail.com>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
2023-11-25 14:51:21 +01:00
Daniel Golle
1b70025ad1 mediatek: remove DTS property added by mistake
Remove bogus 'phy-handle = <&phy0>;', an undefined reference.

Fixes: c8c2f52262 ("mediatek: add support for Zbtlink ZBT-Z8102AX")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-25 03:22:47 +00:00
Daniel Golle
c8c2f52262 mediatek: add support for Zbtlink ZBT-Z8102AX
Specifications:
SoC: MediaTek MT7981B
RAM: 1024MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit)
USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND

Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware

B. Through TFTP
Standard installation via UART:

1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.

Based on patch adding support for similar Zbtlink ZBT-Z8103AX device by
Ian Ishmael C. Oderon.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-24 21:28:35 +00:00
Rani Hod
aaeb379023 mediatek: fiilogic: device tree switch@1f fix
Quite a few `fiilogic` devices use the `mt7531` switch.
Some of them have a DT node that looks like:
```
switch: switch@0 {
	compatible = "mediatek,mt7531";
	reg = <31>;
...
};
```
This commit changes the DT node name to `switch@1f`.

Signed-off-by: Rani Hod <rani.hod@gmail.com>
2023-11-22 19:42:23 +02:00
Chukun Pan
626344c992 mediatek: filogic: add JCG Q30 PRO support
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: Winbond 128MB
  RAM: DDR3 256MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset
  Power: DC 12V 1A

Flash instructions:
  1. Connect to your PC via the Gigabit port of the router,
     set a static ip on the ethernet interface of your PC.
     (ip 192.168.1.254, gateway 192.168.1.1)
  2. Attach UART, pause at u-boot menu.
  3. Select "Upgrade ATF BL2", then use preloader.bin
  4. Select "Upgrade ATF FIP", then use bl31-uboot.fip
  5. Download the initramfs image, and type "reset",
     waiting for tftp recovery to complete.
  6. After openwrt boots up, perform sysupgrade.

Note:
  1. Since NMBM is disabled, we must back up all partitions.
  2. Although we can upgrade new firmware in the stock firmware,
     we need the special fit image signature of MediaTek and
     dual boot (hack kernel) to make u-boot boot it. So just
     abandon these hacks and flash it via the serial port.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-11-19 16:52:16 +01:00
Roland Reinl
44cd32d764 mediatek: Add support for TP-Link EAP225v5
Device specification:
- MT7629 with 16MB NOR flash W25Q128 and 128 MB DDR3 RAM.
- MT7761N and MT7762N wireless chips (currenlty no driver in OpenWrt available)
  - WiFi is NOT working on this device
- Dual core but second CPU doesn't seem to work (Error message during boot: "CPU1: failed to come online")

There are two similar merge requests for similar devices with the same issues:
- https://github.com/openwrt/openwrt/pull/12286
- https://github.com/openwrt/openwrt/pull/5084

UART interface is next to the reset button, pinout:
- 1: TX (the pin with the arrow marker)
- 2: RX
- 3: GND
- 4: VCC

UART settings: 115200,8n1, 3.3V

U-Boot menu can be entered by pressing Ctrl+B during startup.

Booting initramfs:
- Set your computers IP adress to 192.168.1.110
- Run a TFTP server providing the initramfs image
- Power on the AP, press Ctrl+B to get to the U-Boot menu
- Select "1. System Load Linux to SDRAM via TFTP"
- Update kernel file name, input server IP and input device IP (if they deviate from the defaults)
- After booting, create a backup of all partitions, especially for kernel and root_fs. They are required for reverting back to stock firmware
- The sysupgrade image can be flashed now

MAC adresses:
- LAN and 2.4GHz use the same MAC (the one printed on the device)
- 5GHz WiFi MAC is LAN MAC + 1

GPIOs:
- GPIO 21 is the reset pin (low active)
- GPIO 55 is for the green LED (active high)
- GPIO 56 is for the yellow/amber LED (active high)

Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
2023-11-12 17:39:52 +01:00
Roland Reinl
e3a6945b58 mediatek: Add support for D-Link EAGLE PRO AI M32
Specification:
 - MT7622BV SoC with 2.4GHz wifi
 - MT7975AN + MT7915AN for 5GHz
 - MT7531BE Switch
 - 512MB RAM
 - 128 MB flash
 - 3 LEDs (red, orange, white)
 - 2 buttons (WPS and Reset)

MAC addresses:
 - WAN MAC is stored in partition "Odm" at offset 0x83
 - LAN (as printed on the device) is WAN MAC + 1
 - WLAN MAC (2.4 GHz) is WAN MAC + 2
 - WLAN MAC (5GHz) is WAN MAC + 3

Disassembly: Remove 4 screws in the bottom and 2 screws in the top (after removing the blue cover on the top), then the board can be pulled out.

The pins for the serial console are already labeled on the board (VCC, TX, RX, GND). Serial settings: 3.3V, 115200,8n1

Flashing via Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.25
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the status LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-m32-a1-squashfs-recovery.bin

Flashing via uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-m32-initramfs-kernel.bin. You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "1. System Load Linux to SDRAM via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
- The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
- Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later
- Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-m32-squashfs-sysupgrade.bin
- Reboot the device. OpenWrt should start from flash now

Revert back to stock using the Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.25
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the status LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.

Decrypting a D-Link firmware image:
- Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
- Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
- Run ./m32-firmware-util M32 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
- Example for firmware 1.03.01_HOTFIX: ./m32-firmware-util M32 --DecryptFactoryImage M32-REVA_1.03.01_HOTFIX.enc.bin M32-REVA_1.03.01_HOTFIX.decrypted.bin

Revert back to stock using uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides the previously created backup of the Kernel1 partition. You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "2. System Load Linux Kernel then write to Flash via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to FLASH will start. After a few seconds the stock firmware should start again

There is also an image openwrt-mediatek-mt7622-dlink_eagle-pro-ai-m32-a1-squashfs-tftp.bin which can directly be flashed via U-Boot and TFTP. It can be used if no backup of the Kernel1 partition is reuqired.

Flahsing via OEM web interface is currently not possible, the OEM images are encrypted and require a specific memory layout which is not compatible to the partition layout of OpenWrt.

Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
2023-11-12 17:33:41 +01:00
David Bauer
ae500e62e2 mediatek: add label-mac for GL.iNet GL-MT3000
The MAC-address of gmac0 matches the one printed on the bottom label.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-11-03 23:06:33 +01:00
Mikhail Zhilkin
45a50a06fb treewide: fix MERCUSYS brand spelling
This commit fixes MERCUSYS brand spelling. The proper name is capitalized.

Link: https://www.mercusys.com/
Link: https://github.com/torvalds/linux/blob/master/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c#L7779

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-11-03 23:06:07 +01:00
Patryk Kowalczyk
d522ccecb2 filogic: add support for ASUS TUF AX6000
Hardware
========
SOC: MediaTek MT7986
RAM: 512MB DDR3
FLASH: 256MB SPI-NAND
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz 4T4R
ETH: MediaTek MT7530 Switch (LAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (WAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (LAN)
UART: 3V3 115200 8N1 (Do not connect VCC)
USB 3.1

Installation
============

Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.70/24. Rename the image to TUF-AX6000.bin.

Connect to the serial console, interrupt the auto boot process by
pressing '4' when prompted or press '1' and set client IP, server
IP and name of the image.

yOU don't need to open the case or even soldering anything.
use three goldpin wires, remove their plastic cover and connect
them to the console pinout via the case holes.

You can see three holes
From Bottom: RX, TX, Ground - partially covered

Download & Boot the OpenWrt initramfs image.

In case of option '4'
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 TUF-AX6000.bin
$ bootm 0x46000000

In case of option '1'
1: Load System code to SDRAM via TFTP.
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.1.1) ==:
Input server IP (192.168.1.70) ==:
Input Linux Kernel filename (TUF-AX6000.trx) ==:

Wait for OpenWrt to boot. Transfer the sysupgrade
image to the device using scp and install using sysupgrade.

$ sysupgrade -n <path-to-sysupgrade.bin>

Missing features
================

2.5Gb LAN port LED is ON during boot or when the LAN cable is disconnected

The cover yellow light is not supported. (only blue one)

Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
2023-10-31 21:12:15 +01:00
Tianling Shen
423186d7d8 mediatek: add CMCC RAX3000M support
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: 64GB eMMC or 128 MB SPI-NAND
  RAM: 512MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, Mesh
  Power: DC 12V 1A
- UART: 3.3v, 115200n8
  --------------------------
  |         Layout         |
  |   -----------------    |
  | 4 | GND TX VCC RX | <= |
  |   -----------------    |
  --------------------------

Gain SSH access:
1. Login into web interface, and download the configuration.
2. Enter fakeroot, decompress the configuration:
   tar -zxf cfg_export_config_file.conf
3. Edit 'etc/config/dropbear', set 'enable' to '1'.
4. Edit 'etc/shadow', update (remove) root password:
   'root::19523:0:99999:7:::'
5. Repack 'etc' directory:
   tar -zcf cfg_export_config_file.conf etc/
   * If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
     just ignore it.
6. Upload new configuration via web interface, now you can SSH to RAX3000M.

Check stroage type:
Check the label on the back of the device:
"CH EC CMIIT ID: xxxx" is eMMC version
"CH    CMIIT ID: xxxx" is NAND version

eMMC Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'factory' part.
   ('data' partition can be ignored, it's useless.)
2. Write new GPT table:
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
   echo 0 > /sys/block/mmcblk0boot0/force_ro
   dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
   dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync

NAND Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'Factory' part.
2. Erase and write new BL2:
   mtd erase BL2
   mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2
3. Erase and write new FIP:
   mtd erase FIP
   mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP
4. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, erase UBI volumes:
   ubidetach -p /dev/mtd0
   ubiformat -y /dev/mtd0
   ubiattach -p /dev/mtd0
8. Create new ubootenv volumes:
   ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
   ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Additionally, if you want to have NAND recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB
   ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb
10. Perform sysupgrade.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-10-28 19:05:07 +02:00
Jianhui Zhao
fe10f97439 filogic: add support for GL.iNet GL-MT6000
Hardware specification:
* SoC: MediaTek MT7986A 4x A53
* Flash: 8GB EMMC
* RAM: 1GB DDR4
* Ethernet:
  * 2x2.5G RJ45 port (RTL8221B)
  * 4x1G RJ45 ports (MT7531AE)
* WLAN:
  * 2.4GHz: MT7976GN 4T4R
  * 5GHz: MT7976AN 4T4R
* Button: Reset
* LED: 1 x dual color LED
* USB: 1 x USB 3.0
* Power: DC 12V 4A
* UART: 3V3 115200 8N1 (Pinout: GND TX RX VCC)
* JTAG: 9 PIN

If you want to use u-boot from OpenWrt, you can upgrade it safely.
* bl2: openwrt-mediatek-filogic-glinet_gl-mt6000-preloader.bin
* fip: openwrt-mediatek-filogic-glinet_gl-mt6000-bl31-uboot.fip

`openwrt-mediatek-filogic-glinet_gl-mt6000-squashfs-factory.bin` is used in OpenWrt's u-boot.

Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
2023-09-29 00:18:26 +01:00
INAGAKI Hiroshi
7383eb266b mediatek: add support for Buffalo WSR-3200AX4S
Buffalo WSR-3200AX4S is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
MT7622B.

Specification:

- SoC         : MediaTek MT7622B
- RAM         : DDR3 512 MiB
- Flash       : SPI-NAND 128 MiB (Winbond W25N01GVZEIG)
- WLAN        : 2.4/5 GHz 4T4R
  - 2.4 GHz   : MediaTek MT7622B (SoC)
  - 5 GHz     : MediaTek MT7915
- Ethernet    : 5x 10/100/1000 Mbps
  - Switch    : MediaTek MT7531
- LEDs/Keys   : 6x/5x (2x: buttons, 3x: slide-switches)
- UART        : through-hole on PCB (J4)
  - assignment: 3.3V, GND, TX, RX from tri-angle marking
  - settings  : 115200n8
- Power       : 12 VDC, 1.5 A

Flash instruction using factory.bin image:

1. Boot WSR-3200AX4S with "Router" mode
2. Access to "http://192.168.11.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory.bin image and click update ("更新実行")
   button
4. Wait ~120 seconds to complete flashing

Note:

- This device has 2x OS images on flash. The first one will always be
  used for booting and the secondary is for backup.

- This support generates multiple factory*.bin image:

  - factory.bin      : for flashing from OEM WebUI
  - factory-uboot.bin: for flashing from U-Boot or clean installation
                       via sysupgrade (don't use for normal sysupgrade)

Known issues:

- Wi-Fi MAC addresses won't be applied to each adapter.

MAC Addresses:

LAN    : C4:3C:EA:xx:xx:60 (board_data, mac (text))
WAN    : C4:3C:EA:xx:xx:60 (board_data, mac (text))
2.4 GHz: C4:3C:EA:xx:xx:61
5 GHz  : C4:3C:EA:xx:xx:68

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-09-24 18:42:12 +02:00
INAGAKI Hiroshi
9f640cae75 mediatek: separate dts/dtsi for Buffalo WSR series
Separate dts/dtsi from the dts of Buffalo WSR-2533DHP2 to prepare adding
suppport for WSR-3200AX4S.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-09-24 18:42:12 +02:00
INAGAKI Hiroshi
4d9113017b mediatek: drop pwm7_pins from Buffalo WSR-2533DHP2
MediaTek MT7622 doesn't support ch7 of PWM and pinctrl groups were dropped from
driver source[0]. So pwm7-related groups are unavailable now, then, kernel shows a
warning.

[    0.370264] mt7622-pinctrl 10211000.pinctrl: invalid group "pwm_ch7_2" for function "pwm"

Drop that pinmux from pinctrl node.

[0]: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/pinctrl/mediatek/pinctrl-mt7622.c?id=57972641810a97566ffd13e4be3f6a66d61eb3b5

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-09-24 18:42:11 +02:00
INAGAKI Hiroshi
94606abf63 mediatek: add label-mac-device for Buffalo WSR-2533DHP2
Add label-mac-device with "&gmac0" phandle for Buffalo WSR-2533DHP2.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-09-24 18:42:11 +02:00
INAGAKI Hiroshi
de62e01652 mediatek: update NVMEM bindings for Buffalo WSR-2533DHP2
Update NVMEM-related nodes and use newer binding for MAC addresses on
Buffalo WSR-2533DHP2.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-09-24 18:42:11 +02:00
INAGAKI Hiroshi
6b8e7144c8 mediatek: update LED/Key bindings for Buffalo WSR-2533DHP2
Update LED and key nodes with newer DeviceTree bindings for WSR-2533DHP2.

- LED
  - use led-[0-9] for node name of LEDs
  - add "color" and "function" properties
  - drop default-state = "on" from green:power LED
    - this LED will be turned on by led-running alias

- key
  - drop unnecessary poll-interval property
  - use key-[0-9] for node name of keys

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-09-24 18:42:11 +02:00
Elbert Mai
75ee5546e9 mediatek: filogic: add support for Ubiquiti UniFi 6 Plus (U6+)
Ubiquiti U6+ is a dual-band WiFi 6 PoE access point.
It is a drop-in upgrade of the U6 lite.

Specifications
---

- SoC: MediaTek MT7981A dual-core ARM Cortex-A53 1.3 GHz
- RAM: 256 MB DDR3-2133 RAM
- Flash: 16 MB SPI NOR and 4 GB eMMC
- LAN: 1x Gigabit Ethernet with 802.3af/at support
- WLAN: MediaTek MT7976C 2x2 MIMO dual-band WiFi 6
- LEDs: 1x blue and 1x white
- Buttons: 1x reset button

Installation
---

1. Power device using a PoE injector or switch
2. Connect via Ethernet to the device with static IP 192.168.1.2
3. SSH into the device with password: ubnt

        $ ssh ubnt@192.168.1.20

4. Unlock kernel partitions for writing

        $ echo 5edfacbf > /proc/ubnthal/.uf

5. Confirm correct partitions

        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p6/uevent
        PARTNAME=kernel0
        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p7/uevent
        PARTNAME=kernel1
        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p8/uevent
        PARTNAME=bs

6. Set and confirm bootloader environment

        $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt"
        $ fw_setenv bootcmd_real "run boot_openwrt"
        $ fw_printenv

7. Copy sysupgrade image to /tmp/openwrt.bin via scp
8. Copy kernel and rootfs to mmcblk0p6 and mmcblk0p7, respectively

        $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/kernel -O | dd of=/dev/mmcblk0p6
        $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/root -O | dd of=/dev/mmcblk0p7

9. Ensure device boots from mmcblk0p6

        $ echo -ne "\x00\x00\x00\x00\x2b\xe8\x4d\xa3" > /dev/mmcblk0p8

10. Reboot the device

        $ reboot

Signed-off-by: Elbert Mai <code@elbertmai.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2023-09-24 17:16:16 +02:00
Patricia Lee
907e9e0bd3 mediatek: add support for Cetron CT3003
**Hardware specification:**

- SoC: MediaTek MT7981B 2x A53
- Flash: ESMT F50L1G41LB 128MB
- RAM: Nanya NT5CC128M16JR-EK 256MB
- Ethernet: 4 x 10/100/1000 Mbps
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: Reset, Mesh
- Power: DC 12V 1A
- UART: 3.3v, 115200n8
  | Layout:   |
  | :-------- |
  | <Antenna> |
  | VCC       |
  | GND       |
  | Tx        |
  | Rx        |

**Flash instructions:**

1. Rename `openwrt-mediatek-filogic-cetron_ct3003-squashfs-factory.bin` to `factory.bin`.
2. Upload the `factory.bin` using the device's Web interface.
3. Click the upgrade button and wait for the process to finish.
4. Access the OpenWrt interface using the same password.
5. Use the 'Restore' function to reset the firmware to its initial state.

**Notes:**

If you plan to recovery the stock firmware in the future, it's advisable
to connect the device via the serial port and enter failsafe mode to
back up all the MTD partitions before proceeding the steps above.

Signed-off-by: Patricia Lee <patricialee320@gmail.com>
2023-09-08 23:17:26 +02:00
Chen Minqiang
36746893ac mediatek: fix the name of buswidth to bus-width
Fix the issue of dts buswidth cannot be applied properly with spi driver.
Fix the name of buswidth to bus-width in dts in order to fit the format
in linux spi kernel[1] so that spi-tx-bus-width & spi-rx-bus-width can be
parsed properly.

[1] Documentation/devicetree/bindings/spi/spi-controller.yaml

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2023-09-05 15:40:43 +08:00
Daniel Golle
a0f4eadf6a mediatek: add support for Ubiquiti UniFi 6 LR v3
Some recent models of the Ubiquiti Networks UniFi 6 LR access point
come with a RealTek RTL8211FS 1000M/100M/10M PHY instead of the
Aquantia AQR112 2500M/1000M/100M/10M PHY used in both v1 and v2. Add
build for this variant so we can support Ethernet with the PHY.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 16:35:22 +01:00
David Bauer
6dc0675e5b mediatek: enable NMBM remapping for NWA50AX Pro UBI
Don't skip remapping of the UBI area for the ZyXEL NWA50AX Pro. This is
due to the kernel being loaded from the UBI partition by U-Boot.

Link: https://github.com/openwrt/openwrt/pull/13335

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-08-25 21:42:31 +02:00
David Bauer
4c0fdad7ea mediatek: enable NWA50AX Pro eth LEDs
Enable the ethernet LED's on the ZyXEL NWA50AX Pro to show link-state as
well as activity.

Both LED's are configured pulsing.

AMBER | 10/100
GREEN | 1000
A+G   | 2500

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-08-22 13:37:27 +02:00