Fixes following dtc warning:
../dts/rtl838x.dtsi:38.3-145.3: Warning (reg_format): /: Root node has a "reg" property
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware specification
----------------------
* RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz
* 128MB DRAM
* 32MB NOR Flash (MX25L25635E)
* 24 x 10/100/1000BASE-T ports
- Internal PHY with 8 ports (RTL8218B)
- Two external PHYs with 8 ports each (RTL8218B)
* 4 x Gigabit RJ45/SFP Combo ports
- External PHY with 4 SFP ports (RTL8214FC)
* Power LED
* Reset button on front panel
* UART (115200 8N1) via unpopulated standard 0.1" pin header marked J6
UART pinout
-----------
[oooo]J3 [o]ooo|J6
| ^ ||`------ GND
| | |`------- RX
| | `-------- TX
| `---------- Vcc (3V3)
|
`------------------ J3 is power input connector nearby J6 UART
Boot initramfs image from U-Boot
--------------------------------
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Init network with `rtk network on` command
4. Load image with `tftpboot 0x8f000000 openwrt-rtl838x-generic-d-link_dgs-1210-28-initramfs-kernel.bin` command
5. Boot the image with `bootm` command
To install, upload the sysupgrade image to the OEM webpage or sysupgrade
from the system running from initramfs image.
It has been developed and tested on device with F1 revision.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
So the common bits can be easily shared with other boards in the family
and while at it add missing SPDX license identifiers into the DTS files
and fixed alphabetic sorting of the devices in the images.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Ubiquiti EdgeRouter 4 is 4 port Octeon Cavium 7130 powered router.
It has internal power supply and needs c13 power cord.
There are three 10/100/1000 Mbps RJ45/Copper ports and
one 1000 Mbps SFP port connected directly to a SoC.
SoC:
Octeon Cavium 7130 (Cavium 3)
Clocked at 1000Mhz
Memory:
1 GiB (SK hynix H5TQ4G63CFR-RDC × 2)
DDR3, clocked at 533 Mhz (1066Mhz effective)
Flash:
- mtd:
8 MiB (Macronix MX25L6408EMI-12G)
used for uboot/eeprom
- emmc:
4 GiB (SanDisk SDIN7DP2-4G)
used for kernel+rootfs
Leds: 1x for power status (white/blue, controllable)
and 4x for ethernet and sfp ports (no control over them)
Buttons: 1x Reset (from SOC)
Serial: 1x RJ45 port on front panel. 115200 baud, 8N1 (from SoC)
USB: 1x USB3.0 on front panel (from SoC)
MII: 1x QSGMII from SoC is used
PHY: 1x Vitesse VSC8504 of which 4x ports is used
All physical port numbers are properly mapped inside OS and
named by lanX instead of ethX.
There is also special purpose four(4) loopX ports available.
That loopX ports are currently hardcoded by linux kernel
and exact use case of them is currently unknown. We leave them
to the linux kernel and octeon board defaults.
All four (4) physical ports are connected to the same QSGMII.
vsc8504 is used for phys and only 4, 5, 6 and 7 phys are used.
Phy mapping:
- Phy5 is connected to physical eth0 port
- Phy6 is connected to physical eth1 port
- Phy7 is connected to physical eth2 port
- Phy4 is connected to physical eth3 port
Why this device needs external dts:
- faster boot time since need to initialize less device tree nodes.
- to add actual indication with LED about boot/failure/upgrade.
i.e. user could know when to enter failsafe mode or if upgrade is done
- reset button support so user can reset their device in case off failure
- sfp port indication in dmesg with information about sfp module
it also indicates when module inserted or removed
Octeon quirks:
- There is no port status available before it interface brought up
- SFP port can not be tied to actual phy due to octeon-ethernet state
and currently we can only get reports a about SFP state in dmesg
How to flash the firmware:
- copy openwrt-octeon-ubnt_edgerouter-4-initramfs-kernel.bin and
openwrt-octeon-ubnt_edgerouter-4-squashfs-sysupgrade.tar to
USB flash drive that is formatted to vfat/fat32
- connect USB flash drive to edgerouter 4 front USB port
- connect serial cable using front RJ45 port (115200 baud, 8N1)
- connect power to cable to edgerouter 4
- connect terminal to the console to see uboot boot process
- interrupt boot by pressing button(s) on your keyboard to log in to the uboot
- detect usb connected flash drives by typing to the console:
usb start
- after drive is detected load initramfs+kernel to the memory by typing:
fatload usb 0:1 0x20000000 openwrt-octeon-ubnt_edgerouter-4-initramfs-kernel.bin
- after initramfs+kernel is loaded to the memory load it by typing:
bootoctlinux 0 numcores=4 endbootargs mem=0
- boot process should finish and you will be greeted with console after pressing enter
- create directory to mount usb flash drive to by typing:
mkdir /tmp/sda
- mount flash drive to that directory by typing:
mount /dev/sda1 /tmp/sda
- flash firmware to router internal storage by typing:
sysupgrade /tmp/sda/openwrt-octeon-ubnt_edgerouter-4-squashfs-sysupgrade.tar
- device will reboot and after it gets up you will have edgerouter 4 running openwrt
Reviewed-by: Johannes Kimmel <fff@bareminimum.eu>
Tested-by: Johannes Kimmel <fff@bareminimum.eu>
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
adds patch to octeon ethernet driver that lets sgmii interface
device tree node to be disabled and that disabled interface
won't be unnecessarily initialized.
It solves the problem with octeon boards that have 8 sgmii or more ports
initialized but have nothing connected to them.
Tested-by: Johannes Kimmel <fff@bareminimum.eu>
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
adds patch to octeon ethernet driver that to rename interface
name by label from device tree
Tested-by: Johannes Kimmel <fff@bareminimum.eu>
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
adds support for vsc8504 phy.
patch have use on 5.4 kernel and has
to be dropped after since phy is supported by
CONFIG_MICROSEMI_PHY on newer LTS kernels.
Tested-by: Johannes Kimmel <fff@bareminimum.eu>
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
Use the default sysupgrade generation procedure provided
by the target. The previously generated images had the rootfs not
aligned to an eraseblock.
Signed-off-by: David Bauer <mail@david-bauer.net>
Remove MDIO and I2C bitbangig support from the kernel.
These functionalities are currently not used by any board in the target.
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit fixes the name for the GMAC clock to gmac_clkin, as this is
the name of the clock provided by the rk3328-clk driver.
Without this commit, the GMAC will not work in TX direction.
Suggested-by: Tobias Waldvogel <tobias.waldvogel@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
`mt7621_nfc_write_page_hwecc` may be called with `buf=NULL`, but
`mt7621_nfc_check_empty_page` always tries to read it.
That caused Oops:
`Unable to handle kernel paging request at virtual address 00000000`
Fixes: FS#3416
Signed-off-by: Anton Ryzhov <anton@ryzhov.me>
Several Ubiquiti WA devices set up &wmac again in their DTS files,
although this is already done in ar9342_ubnt_wa.dtsi.
Fixes: fa3c2676ab ("ath79: Add support for Ubiquiti Nanostation AC")
Fixes: cf5a1abe46 ("ath79: define 2.4GHz radio for nanostation ac loco")
Fixes: 09804da80a ("ath79: define 2.4GHz radio for litebeam ac gen2")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The ar9342 Ubiquiti WA devices appear to only have two different
network setups, based on the number of ethernet ports.
Create DTSI files for them to consolidate duplicate definitions.
Signed-off-by: Nick Hainke <vincent@systemli.org>
[rephrase commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In 4.14 the delays were not cleared, so setting "rgmii" as phy-mode
did not affect delays set by the bootloader. With 5.4 kernel the
situation changed and the ethernet interface stopped working.
"rgmii" requires rx and tx delays depending on the hardware circuit
and wiring. The mac or the phy can add these delays.
- "rgmii": delays are controlled by the mac
- "rgmii-id": delays are controlled by the phy
More Information in Linux Kernel Tree:
Documentation/devicetree/bindings/net/ethernet-controller.yaml
"rgmii" should be the preferred mode, which allows the mac layer to
turn off the dealys completely if they are not needed. However, the
delays are not set correctly, which causes the ethernet interface
to be broken. Just taking the ethernetpart from the litebeam ac gen2
will fix the issue.
Explained-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Nick Hainke <vincent@systemli.org>
In kernel commit adf82accc5f5 ("netfilter: x_tables: merge ip and
ipv6 masquerade modules") the config symbols IP_NF_TARGET_MASQUERADE
and IP6_NF_TARGET_MASQUERADE have been demoted to simple backwards-
compat options for NETFILTER_XT_TARGET_MASQUERADE.
In netfilter.mk, this has already been updated in OpenWrt commit
d1592306cc ("netfilter.mk: use CONFIG_NETFILTER_XT_TARGET_MASQUERADE"),
having us use the new config symbol.
However, enabling IP_NF_NAT or IP6_NF_NAT still makes the relevant
legacy options selectable, so we need to disable them in generic
config (and forget about them afterwards).
Since CONFIG_IP_NF_TARGET_MASQUERADE is already present there, this
just adds the missing CONFIG_IP6_NF_TARGET_MASQUERADE.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Kernel has removed the symbols CONFIG_NF_NAT_IPV4 and
CONFIG_NF_NAT_IPV6 in favor of CONFIG_NF_NAT in commit
3bf195ae6037 ("netfilter: nat: merge nf_nat_ipv4,6 into nat core").
This drops the obsolete symbol CONFIG_NF_NAT_IPV6 from generic
config-5.4.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This partition isn't normally modified during boot process. Make it
read-only to prevent accidental overwrite.
If needed this can be overriden with installing kmod-mtd-rw; the same
way as for installing modified U-boot.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
This partition isn't normally modified during boot process. Make it
read-only to prevent accidental overwrite.
If needed this can be overriden with installing kmod-mtd-rw; the same
way as for installing modified U-boot.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
The mount point is "/tmp/boot", the path in the boot partition is
"/boot/grub/upgraded".
Origin of this mark b9c1cf16 ("x86: add preinit hook for bootloader
upgrade")
Fixes 32f675ca ("x86: fix grub-bios-setup fail during sysupgrade")
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3140
Reported-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
It's not possible to compile some applications which are using
`-Werror=missing-include-dirs` compiler flags with the SDK as some
target directories are missing in the SDK tarball:
cc1: error: staging_dir/target/usr/include: No such file or directory [-Werror=missing-include-dirs]
cc1: error: staging_dir/target/include: No such file or directory [-Werror=missing-include-dirs]
Fix this by adding the missing directories in the SDK.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This re-enables offloading features disabled by
commit 9da2b56760 ("ipq40xx: fix ethernet vlan double tagging").
Single-PHY devices use port-based VLANs on the switch, therefore no
S-TAG magic is involved here. Re-enabling these features restores
throughput back to 950 Mbit/s.
Reported-by: Jannis Pinter <jannis@pinterjann.is>
Signed-off-by: David Bauer <mail@david-bauer.net>
The Ubiquiti UniFi AP does not have a AHB connected radio but a PCI one.
Also the EEPROM ist only 0x440 bytes of length.
Reported-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Signed-off-by: David Bauer <mail@david-bauer.net>
The AT803X_PHY kernel config symbol is already enabled target-wide. SO
it does not have to be enabled for individual subtargets.
Signed-off-by: David Bauer <mail@david-bauer.net>
Patch was upstreamed a long time ago (over 2 years) as commit
a08227a206b8d ("MIPS: ath79: select the PINCTRL subsystem").
When porting this patch to a newer kernel, nobody noticed we now patch a
Broadcom platform. This is clearly not intended. So drop this patch and
pretend nothing ever happened.
Signed-off-by: David Bauer <mail@david-bauer.net>
This removes unneeded kernel version switches from the targets after
kernel 4.19 has been dropped.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
We use 5.4 on all targets by default, and 4.19 has never been released
in a stable version. There is no reason to keep it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch disables the image for edgerouter devices by default, since
it isn't able to boot at the moment.
Currently the edgerouter image won't boot. Current kernels have an
option CONFIG_CAVIUM_CN63XXP1 that needs to be enabled for this chip.
If the kernel was compiled without this option, following message is
displayed and the machine reboots:
[ 36.778028] Kernel panic - not syncing: OCTEON II DCache prefetch workaround not in place (cfa0000c).
[ 36.778028] Please build kernel with proper options (CONFIG_CAVIUM_CN63XXP1).
[ 36.794398] Rebooting in 1 seconds..
This was last confirmed on 2020-10-29.
The description of this option states, that enabling it will possibly
cause performance issues on other chips.
Signed-off-by: Johannes Kimmel <fff@bareminimum.eu>
A typo resulted in that module having it's own menu.
Move it into the I2C menu as it was most likely intended.
Fixes: 1291274335 ("kernel: package bcm53xx i2c module")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
With the fix of external kmod feeds it is possible to ship the
ImageBuilder without any packages except the pseudo packages kernel and
libc. Therefore the local package feeds becomes optional.
This commit adds a check to the package_reload function to only run if
the local feed is existing.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The buildbots generate a kmod archive which should be used instead of a
local copy. This is possible due to the introduction of a kernelversion
specific feed.
This commit adds the ability of using only signed package feeds.
Signed-off-by: Paul Spooren <mail@aparcar.org>
- minimal built initramfs: 10MB vmlinux ELF -> 6MB vmlinuz
- ~5 seconds for kernel decompression, which was equivalent to the
additional time to load the uncompressed ELF from SPI NOR.
- Removes requirement for lzma-loader, which may have been causing some
image builds to fail to boot on Mikrotik mt7621.
Suggested-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
- minimal built initramfs: 11MB vmlinux ELF -> 4.5MB vmlinuz
- ~5 seconds for kernel decompression, which was equivalent to the
additional time to load the uncompressed ELF from SPI NOR.
- Removes requirement for lzma-loader, which may have been causing some
image builds to fail to boot on Mikrotik mt7621.
Fixes: FS#3354
Suggested-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
This will make a separated section for dtb appear in ELF, and we can
then use objcopy to patch a dtb into vmlinuz when RAW_APPENDED_DTB
is set in kernel config.
command to patch a dtb:
objcopy --set-section-flags=.appended_dtb=alloc,contents \
--update-section=.appended_dtb=<target>.dtb vmlinuz vmlinuz-dtb
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
linux-mips has zboot code which can create a self-extracting kernel
image.
This allows enabling kernel zboot support for ramips targets.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Same hardware as Phicomm K2G but different flash layout.
Specification:
- SoC: MediaTek MT7620A
- Flash: 8 MB
- RAM: 64 MB
- Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5)
- Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped
with external PA.
- UART: 1 x UART on PCB - 57600 8N1
Flash instruction:
To avoid requiring UART for TFTP a dual flash procedure is suggested
to install the squashfs image:
1. Rename openwrt-ramips-mt7620-wavlink_wl-wn530hg4-initramfs-kernel.bin
to WN530HG4-WAVLINK.
2. Flash this file with the factory web interface.
3. With OpenWRT now running use standard sysupgrade to install the
squashfs image.
Signed-off-by: Nuno Goncalves <nunojpg@gmail.com>
[remove dts-v1, remove model from LED labels, wrap commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Move CPU_TYPE:=24kc (32-bit) from the top-level target makefile to the
be/le subtarget makefiles, which is consistent with the 64-bit subtargets.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Hardware:
- SoC: Lantiq VRX 220
- CPU: 2x MIPS 34Kc 500 MHz
- RAM: 128 MiB 250 MHz
- Flash: 128 MiB NAND
- Ethernet: Built-in Fast Ethernet switch, 4 ports used
- Wifi: Atheros AR9381-AL1A b/g/n with 2 pcb/internal and 1 external antennas
- USB: 1x USB 2.0
- DSL: Built-in A/VDSL2 modem
- DECT: Dialog SC14441
- LEDs: 1 two-color, 4 one-color
- Buttons: 1x DECT, 1x WIFI
- Telephone connectors: 1 FXS port via TAE or RJ11 connector
With the exception of FXS/DECT everything works
(there are no drivers for AVM's FXS or DECT implementation),
DSL is yet untested.
Installation:
Boot up the device and wait a few seconds. Run the eva_ramboot.py script
in scripts/flashing/ to load the initramfs image on the device:
$ ./scripts/flashing/eva_ramboot.py 192.168.178.1 <path to your initramfs image>
If the script fails to reach the device, maybe try 169.254.120.1.
Wait until booting is complete. You should now be able to reach your device
under the default ip address 192.168.1.1.
Before flashing, check if linux_fs_start is not set to 1 in the tffs partition:
$ fritz_tffs_nand -d /dev/mtd1 -n linux_fs_start
If linux_fs_start is 1, you will need to reset it to 0, either by FTP,
upgrading FritzOS or doing a recovery.
Now you should be able to flash the device using sysupgrade.
Signed-off-by: Leon Maurice Adam <leon.adam@aol.de>
Acked-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[drop BOARD_NAME, use wpad-basic-wolfssl, drop 4.19, drop dts-v1,
remove model prefix from LED names]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
At the moment, bcm63xx creates one patch for each board to add to
board_bcm963xx.c. While this is not really helpful to get an overview
in the first place, it is particularly painful if you want to change
something for an early file and have to refresh all the later patches
accordingly.
Since it does not look like these board patches are upstreamed either,
this commit consolidates all board additions into one patch per "board".
By this, both adding and editing boards should become much simpler,
and we drop about 1300 lines of "code" from patches as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This supports upgrade from ar71xx for the recently added Qxwlan
devices E1700AC v2, E558 v2, E750A v4 and E750G v8.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All octeon devices use the same or a very similar way to backup
and restore configuration.
We expect to have more devices added and in order to stop
repeating ourselves move the logic to a separate function.
While at it, add a few checks.
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
[commit message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The block protection bits of macronix do not match the implementation.
The chip has 3 BP bits. Bit 5 is actually the third BP but here the
5th bit is SR_TB. Therefore the patch adds SR_TB to the mask. In the
4.19er kernel the whole register was simply set to 0.
The wrong implementation did not remove the block protection. This led
to jffs2 errors in the form of:
"jffs2: Newly-erased block contained word 0x19852003 at offset 0x..."
This caused inconsistent memory and other errors.
Suggested-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Nick Hainke <vincent@systemli.org>
NXP linux factory unifies one linux kernel for i.MX, Layerscape and
S32 platforms. It provides a common code base for their SDKs.
Add several kernel patches for bug fix from linux factory last release.
Git: https://source.codeaurora.org/external/qoriq/qoriq-components/linux
Tag: LTS-5.4.47-20200828
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
