By dropping _machine_restart, users can provide more reliable or
device-specific restart modes.
_machine_halt was already removed in commit f4b687d1f0 ("realtek: use
kernel defined halt"), but quietly reintroduced in commit 8faffa00cb
("realtek: add support for the RTL9300 timer"). Let's remove it again.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Add and enable the Realtek Otto WDT peripheral found on these SoCs.
Default all devices to use standard (cold) reboot and "soc" resets.
Devices that require the PLL value fixup before restarting, should pick
the "cpu" or "software" reset mode. These devices also need to provide a
custom reboot mode, by adding the reboot argument to the kernel command
line:
WDT reset mode | kernel reboot mode
----------------+---------------------------------------
soc | reboot=cold (default if not specified)
cpu | reboot=warm
software | reboot=software
Preferrably, these devices should use an alternative restart method like
gpio-restart to provide reliable restarts.
Note that watchdog restarts are not yet exposed, since the
_machine_restart override is still present.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Add patch submitted upstream to linux-watchdog and replace the MIPS
architecture symbols. Requires one extra patch for the DIV_ROUND_*
macros, which have moved to a different header since 5.10.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
The CPU peripherals on RTL83xx/RTL930x are connected to the CPU via the
Lexra bus. This bus can provide a clock signal to these peripherals, but
no clock driver is currently available. Instead, use a fixed-clock to
provide the clock frequency, and update the dependent peripherals.
Lexra bus clock frequencies:
- RTL838x: 200MHz
- RTL839x: 200MHz
- RTL930x: 175MHz
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
All current devices use identical bootargs, so let's move that to the
common devicetree includes.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Recent versions of Realtek's SDK reset both the ethernet NIC and queues
(SW_NIC_RST and SW_Q_RST bits) when initialising the hardware.
Furthermore, when issuing a CPU reset on the Zyxel GS1900-8 (not
supported by any current driver), the networking part of the SoC is not
reset. This leads to unresponsive network after the restart. By
resetting both the ethernet NIC and queues, networking always comes up
reliably.
Suggested-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
If authentication fails repeatedly e.g. because of a weak signal, the link
can end up in blocked state. If one of the nodes tries to establish a link
again before it is unblocked on the other side, it will block the link to
that other side. The same happens on the other side when it unblocks the
link. In that scenario, the link never recovers on its own.
To fix this, allow restarting authentication even if the link is in blocked
state, but don't initiate the attempt until the blocked period is over.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some drivers that do their own sequence number allocation (e.g. ath9k, mwlwifi) rely
on being able to modify params->ssn on starting tx ampdu sessions.
This was broken by a change that modified it to use sta->tid_seq[tid] instead.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When procd-ujail is available, 1f78538387 runs hostapd as user
"network", with only limited additional capabilities (CAP_NET_ADMIN and
CAP_NET_RAW).
hostapd_cli (CONFIG_PACKAGE_hostapd-utils) communicates with hostapd
over a named UNIX-domain socket. hostapd_cli is responsible for creating
this socket at /tmp/wpa_ctrl_$pid_$counter. Since it typically runs as
root, this endpoint is normally created with uid root, gid root, mode
0755. As a result, hostapd running as uid network is able to receive
control messages sent through this interface, but is not able to respond
to them. If debug-level logging is enabled (CONFIG_WPA_MSG_MIN_PRIORITY
<= 2 at build, and log_level <= 2 in /etc/config/wireless wifi-device),
this message will appear from hostapd:
CTRL: sendto failed: Permission denied
As a fix, hostapd_cli should create the socket node in the filesystem
with uid network, gid network, mode 0770. This borrows the presently
Android-only strategy already in hostapd intended to solve the same
problem on Android.
If procd-ujail is not available and hostapd falls back to running as
root, it will still be able to read from and write to the socket even if
the node in the filesystem has been restricted to the network user and
group. This matches the logic in
package/network/services/hostapd/files/wpad.init, which sets the uid and
gid of /var/run/hostapd to network regardless of whether procd-ujail is
available.
As it appears that the "network" user and group are statically allocated
uid 101 and gid 101, respectively, per
package/base-files/files/etc/passwd and USERID in
package/network/services/hostapd/Makefile, this patch also uses a
constant 101 for the uid and gid.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
[refreshed patch]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix the return value, shell return codes should be 0 to indicate success
(i.e. mount point found), 1 should be failure (i.e. mount point not-found).
Fixes: ac4e8aa ("dnsmasq: fix more dnsmasq jail issues")
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
Extend the hotplug.json ruleset to setup the common /dev/std{in,out,err}
symbolic links which are needed by some applications, e.g. nftables when
applying rulesets from stdin.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
8de12de system: add diskfree infos to ubus
bf3fe0e service: move jail parsing to end of instance parser
87b5836 procd: add full service shutdown prior to sysupgrade
01ac2c4 procd: service_stop_all: also kill inittab actions
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This fixes WARNing, missing clocks and
[ 10.422481] bcm_ns_usb2 1800c164.usb2-phy: Clock not defined
Fixes: 5901917b93 ("bcm53xx: use more upsteam DT patches from 5.16 / 5.17")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes:
[ 10.440495] bcm_ns_usb2 1800c000.usb2-phy: can't request region for resource [mem 0x1800c000-0x1800cfff]
[ 10.450039] bcm_ns_usb2 1800c000.usb2-phy: Failed to map DMU regs
[ 10.456183] bcm_ns_usb2: probe of 1800c000.usb2-phy failed with error -16
caused by conflict in allocating resources.
Fixes: f55f1dbaad ("bcm53xx: switch to the kernel 5.10")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
5dd32475c859 mt76: mt7915: get rid of mt7915_mcu_set_fixed_rate routine
f5cfaaff3dd1 mt76: mt7921: drop offload_flags overwritten
f5ad840ca5c0 mt76: mt7615: fix possible deadlock while mt7615_register_ext_phy()
29a8a08827b1 mt76: mt7921: fix MT7921E reset failure
f44685f2faee mt76: mt7915: fix return condition in mt7915_tm_reg_backup_restore()
ae8e02ddd2b0 mt76: mt7915: fix SMPS operation fail
e814e15716b0 mt76: reverse the first fragmented frame to 802.11
c9bca3ed9566 mt76: mt7915: fix NULL pointer dereference in mt7915_get_phy_mode
dd054b7e16e7 mt76: only set rx radiotap flag from within decoder functions
f1520c9bb332 mt76: mt7915: add default calibrated data support
0c489ea2865a mt76: testmode: add support to set MAC
91c5da3d0a7c mt76: mt7921: add support for PCIe ID 0x0608/0x0616
ca39b4bbc227 mt76: debugfs: fix queue reporting for mt76-usb
00b6f497e2e8 mt76: mt7921: introduce 160 MHz channel bandwidth support
c1574466c733 mt76: fix possible OOB issue in mt76_calculate_default_rate
9680a17b0aed mt76: mt7921: fix possible NULL pointer dereference in mt7921_mac_write_txwi
78fc0dcdcef0 mt76: connac: fix a theoretical NULL pointer dereference in mt76_connac_get_phy_mode
05953e7d6fe7 mt76: mt7615: remove dead code in get_omac_idx
39f6c37127c1 mt76: connac: remove PHY_MODE_AX_6G configuration in mt76_connac_get_phy_mode
526591b203f3 mt76: do not pass the received frame with decryption error
256789bb400f mt76: fix the wiphy's available antennas to the correct value
fa187f5cf068 mt76: fix timestamp check in tx_status
11ebf11a3587 mt76: mt7915: fix the wrong SMPS mode
8c69b815ee7f mt76: mt7921: honor mt76_connac_mcu_set_rate_txpower return value in mt7921_config
bc6798f729f9 mt76: move sar utilities to mt76-core module
b1d0ad2e74fe mt76: mt76x02: introduce SAR support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
sun6i-rtc cannot be built as a module and the hardware is only
present in some of the sunxi SoCs, see driver source:
{ .compatible = "allwinner,sun6i-a31-rtc" },
{ .compatible = "allwinner,sun8i-a23-rtc" },
{ .compatible = "allwinner,sun8i-h3-rtc" },
{ .compatible = "allwinner,sun8i-r40-rtc" },
{ .compatible = "allwinner,sun8i-v3-rtc" },
{ .compatible = "allwinner,sun50i-h5-rtc" },
{ .compatible = "allwinner,sun50i-h6-rtc" },
Set CONFIG_RTC_DRV_SUN6I=y in kernel config file for cortexa7 and
cortexa53 subtargets which covers all of the above.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
sun6i-rtc is a builtin_platform_driver and cannot be built as a module.
Hence this reverts commit e178d9a549.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The llvm-bpf-$version.tar.xz might be absent. For example `make clean` executed, CONFIG_TARGET changed.
This commit can only guarantee that the target file can be built when tools/compile is explicitly called rather than $(tools/stamp-compile).
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
Correct ralink_i2s_debugfs_remove declaration in ralink patches when
CONFIG_DEBUG_FS is not selected.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This commit adds support for the Wavlink WL-WN576A2 wall-plug wireles
repeater / router. It is also sold under the name SilverCrest SWV 733 B1.
Device specs:
- CPU: MediaTek MT7628AN
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 1x 10/100 Mbps
- 2.4 GHz: b/g/n SoC
- 5 GHz: a/n/ac MT7610EN
- Buttons: WPS, reset, sliding switch (ap/repeater)
- LEDs: 5x wifi status, 1x LAN/WAN, 1x WPS
Flashing:
U-Boot launches a TFTP client if WPS button is held during boot.
- Server IP: 192.168.10.100
- Firmware file name: firmware.bin
Device will reboot automatically. First boot takes about 90s.
Coelner (waenger@gmail.com) is the original author, but I have made some
fixes. He does not wish to sign off using his real name.
Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
A define dealing with builtin type is wrong. A gnulib update fixes
this, but that requires a new cpio version.
Refresh other patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Further devices from the series have been added in the meantime,
introducing `qca955x_dlink_dap-2xxx.dtsi`.
Thus, merge support for DAP-2695 with the existing dtsi.
This implies factory images can now be flashed via the regular
OEM Web UI, as well as the bootloader recovery.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
This device can be merged with the existing dtsi, which declares
the location of ath9k cal-data via devicetree, correcting the 2.4G
mac address in `10_fix_wifi_mac` rather than `10-ath9k-eeprom`.
To make these changes more visible, apply before merging with dtsi.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
This device can be merged with the existing dtsi,
which will increase spi-max-frequency to 50 MHz.
To make this change more visible, increase to 50 MHz before merging.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
The MikroTik LHG 5 series (product codes RBLHG-5nD, RBLHG-5HPnD and
RBLHG-5HPnD-XL) devices are an outdoor 5GHz CPE with a 24.5dBi or 27dBi
integrated antenna built around the Atheros AR9344 SoC.
It is very similar to the SXT Lite5 series which this patch is based
upon.
Specifications:
- SoC: Atheros AR9344
- RAM: 64 MB
- Storage: 16 MB SPI NOR
- Wireless: Atheros AR9340 (SoC) 802.11a/n 2x2:2
- Ethernet: Atheros AR8229 switch (SoC), 1x 10/100 port,
8-32 Vdc PoE in
- 8 user-controllable LEDs:
- 1x power (blue)
- 1x user (white)
- 1x ethernet (green)
- 5x rssi (green)
See https://mikrotik.com/product/RBLHG-5nD for more details.
Notes:
The device was already supported in the ar71xx target.
Flashing:
TFTP boot initramfs image and then perform a sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Jakob (Jack/XDjackieXD) <jakob@chaosfield.at>
