New U-Boot version for MediaTek MT76x8/MT762x based ALFA Network boards
includes support for a 'dual image' feature. Users can enable it using
U-Boot environment variable 'dual_image' ('1' -> enabled).
When 'dual image' feature is enabled, U-Boot will modify DTB and divide
the original 'firmware' flash area into two, equal in size and aligned
to 64 KB partitions: 'firmware' and 'backup'. U-Boot will also adjust
size of 'firmware' area to match installed flash chip size.
U-Boot will load kernel from active partition which is marked with env
variable 'bootactive' ('1' -> first partition, '2' -> second partition)
and rename both partitions accordingly ('firmware' <-> 'backup').
There are 3 additional env variables used to control 'dual image' mode:
- bootlimit - maximum number of unsuccessful boot tries (default: '3')
- bootcount - current number of boot tries
- bootchanged - flag which informs that active partition was changed; if
it is set and 'bootcount' reaches 'bootlimit' value,
U-Boot will start web-based recovery which then updates
both partitions with provided image
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(backported from commit bc173ddd83)
Upstream kernel added support for RAW_APPENDED_DTB on ralink arch
in the following commit:
02564fc89d3d ("ralink: Introduce fw_passed_dtb to arch/mips/ralink")
Use upstream solution and get rid of our OWRTDTB hack.
This commit set DEVICE_DTS to $$(DTS) instead of replacing DTS with
DEVICE_DTS in device profile because DTS variable will be dropped
in later commits.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on mt7621/mt76x8]
Tested-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on rt305x/mt7620]
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(cherry picked from commit 7a8d3432c7)
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Ath10k packages were removed from ar71xx in master in commit
34113999ef ("ar71xx: Remove ath10k packages from archer-c7-v1 (fixes
FS#1743)") but ath79 in master and the 19.07 branch still suffer from
the issue.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[commit subject and description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware
--------
SoC: Qualcomm IPQ4019
RAM: 256M DDR3
FLASH: 128M NAND
WiFi: 2T2R IPQ4019 bgn
2T2R IPQ4019 a/n/ac
ETH: Atheros AR8033 RGMII PHY
BTN: 1x Connect (WPS)
LED: Power (green/red/yellow)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz1200'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz1200.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ1200.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz1200.bin uboot0
> mtd write /path/to/uboot-fritz1200.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 7f187229a8)
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This was found by the build bot.
Fixes: db345220b4 ("kernel: bump 4.14 to 4.14.155")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 103e49f62e)
While at it, also reorder the items for
improved readability.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit 6b2f953db346cfb4ddf05654efa3ad7eb84ed99f)
TP-Link TL-WDR4900 v2 only has one combined WPS/Reset button, so
don't set up an RFKILL for this device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 25127f58b4)
In ar71xx there is only one combined mach file for Archer C5/C7 and
TL-WDR4900 v2. This one uses the same LED struct for all devices,
defining "green" LEDs for them. However, WDR4900 uses blue front
LEDs, while only C5/C7 uses green ones. Despite, in base-files
WDR4900 is actually set up with "blue" for the mentioned LEDs.
Thus, this patch creates a separate LED struct for WDR4900, so the
LEDs can be set up correctly. Despite, the wlan5g LED is removed as
it is controlled by ath9k chip for WDR4900 (in contrast to C5/C7).
Note: While front LEDs are blue, USB LEDs (on the back) are green,
so colors are mixed intentionally for the WDR4900 v2.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 93f2bcc35e)
The stock firmware and bootloader only accept uImage with names that
match certain patterns. This patch enables OpenWrt installation from
stock firmware without having to reflash the bootloader or access the
UART console.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 19800ac095)
[backported]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The MAC address setup of the TL-WDR4900 v2 is different from the
C5/C7. This aligns ar71xx with the setup in ath79:
wlan0 (5GHz) : -2
wlan1 (2.4GHz) : -1
eth1 (LAN) : 0
eth0 (WAN) : 1
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a9d3084b83)
As discussed in 1d18a14a90 ("ath79: really fix TP-Link Archer C7
v2 MAC address"), stock firmware MAC address assignment is
actually as follows:
wlan0 (5GHz) : -1
wlan1 (2.4GHz) : 0
eth1 (LAN) : 0
eth0 (WAN) : 1
This has never been fixed for ar71xx, so let's do it now.
Note that with WDR4900 v2 even both wlan0 and wlan1 where assigned
to basemac-1 before ...
Fixes: FS#408
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a021268032)
ar71xx has just one board name "wndr3700" for WNDR3700 V1/V2,
WNDR3800 and WNDR3800CH, whereas ath79 provides separate images for
the boards. So, update SUPPORTED_DEVICES to store the correct
ar71xx board names.
Fixes: FS#2510
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit fc44a8481c)
Some Ubiquiti devices had the RSSI LEDs configured in 01_leds but
were missing the rssileds package, while others that don't have
RSSI LEDS had the package included.
This commit includes the rssileds package only for those devices
that need it.
Tested on a NanoStation M XW.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
(cherry picked from commit 1c6066a867)
[backported to 19.07]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The two ASUS WL-330N and WL-330N3G had the
reset keycode assigned to the WPS button. This patch
changes all three devices to use KEY_WPS_BUTTON in
the hopes that this fixes unwanted restarts/
unexpected behavior from the users point of view.
[dropped RG21S]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit ad65d9d7b2)
The WPS button was mapped to the restart/reset. This patch
changes it to emit the KEY_WPS_BUTTON keycode so pressing
the WPS button does initiate WPS.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 7a7610c21b)
Disable the DIR-300 B1 image by default as the device has insufficient
flash space for release build images.
Fixes: FS#2606
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Commit 60f41c6c9e ("ramips: add usb-ledtrig-usbport to DEVICE_PACKAGES
of CY-SWR1100") added stray | during backport which caused build
breakage on the buildbots:
bash: -c: line 0: syntax error near unexpected token `|'
bash: -c: line 0: `echo kmod-usb-core kmod-usb-ledtrig-usbport kmod-usb-ohci kmod-usb2 swconfig | | mkhash md5 | head -c 8'
Fixes: 60f41c6c9e ("ramips: add usb-ledtrig-usbport to DEVICE_PACKAGES of CY-SWR1100")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
CY-SWR1100 has a USB LED but kmod-usb-ledtrig-usbport is missing
in default images. This commit adds it.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[changed commit title, backported to 19.07]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 261c746631)
Ethernet MAC address setup has been broken since c3e420f28c. Restore
original setting.
Fixes: c3e420f28c ("ramips: Add support for D-Link DCH-M225")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 7231c1edd9)
[backported due to base-files split]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In ar71xx, the board name for the TL-WR1043ND v3 is equal to v2:
tl-wr1043nd-v2
Fix SUPPORTED_DEVICES for v3 in ath79 accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit b5791118cc)
Fix the error that tl-wdr3320-v2 can't upgrade firmware via web
interface by using magic_ver="0200" for this device.
Signed-off-by: 南浦月 <nanpuyue@gmail.com>
[commit message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 0ff2385a92)
When Nanostation M was renamed from ubnt,nano-m to ubnt,nanostation-m
in commit f1396ac753 ("ath79: align naming of Ubiquiti Nanostation M"),
the caldata extraction in 10-ath9k-eeprom was overlooked.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 5dc535419f)
All buttons on the Netgear R6220 are active-low while they are flagged
as active-high.
The GPIO status reads the following for no buttons pressed:
root@64367-r6220:~# cat /sys/kernel/debug/gpio
gpio-7 ( |wps ) in hi
gpio-8 ( |wifi ) in hi
gpio-14 ( |reset ) in hi
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit f7f9fe5256ebb660d3160452c3c01a9eb080938f)
This fixes the netdev LED trigger for interfaces, which are renamed
during initialization (e.g. ppp interfaces).
Fixes: FS#2193
Fixes: FS#2239
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit edbadec843)
To simplify the upgrade process and ensure easier identification of
device partitioning, the following devices are disabled on ath79
target in openwrt-19.07 branch:
- glinet,gl-ar300m-nor
- glinet,gl-ar300m-nand
- glinet,gl-ar750s
Proper ath79 (NAND) support for the devices is expected to be
introduced based on kernel 4.19 (see GitHub PR #2184).
In openwrt-19.07, ar71xx should be used for those devices.
With this, we ensure that the new ath79 image names (at least for
releases) refer to the updated partitioning.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This fixes commit bae927c551 ("ar71xx: add support for TP-LINK CPE510
V2.0") where the support for this device wasn't optimal.
Device support for the CPE510v2 so far has been a hack to enable
flashing with CPE510v1 images. Those even have different hardware (e.g.
additional ethernet port).
With this patch, we provide proper support for this device in ar71xx.
Installation:
- Flash factory image through stock firmware WEB UI or through TFTP
- To get to TFTP recovery just hold reset button while powering on
for around 4-5 seconds and release.
- Rename factory image to recovery.bin
- Stock TFTP server IP: 192.168.0.100
- Stock device TFTP address: 192.168.0.254
Fixes: bae927c551 ("ar71xx: add support for TP-LINK CPE510 V2.0")
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[Rebased onto revert commit, changed comments in mach-cpe510.c,
changed commit title and description, fixed eth0 MAC address,
removed eth1 initialization]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[squashed revert, added fixes tag]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c79b796280)
[added CPE510V2 entry to tplink-safeloader.c]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There is a problem with the EA8500, the switch will not work after soft
reboot, the only way to get it working again is to power cycle it
manually.
There are probably several issues in the play, it's quite hard to fix it
without having access to the actual device, so I don't see any other
option now, then revert the offending commit.
Ref: PR#2047
Fixes: FS#2168 ("Switch no longer work after restart on Linksys EA8500")
Reported-by: Adam <424778940z@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 04d6753d03)
With this commit, the WAN LED is triggered by the switch port state
instead of the eth0 netdev.
Otherwise, the LED is always illuminated, regardless of the WAN port
link state.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 70d5989c9c)
Signed-off-by: David Bauer <mail@david-bauer.net>
Both targets miss a subtarget causing an image naming style which is
different from other all othe targets, even tho it already uses
`x/generic/` as subfolder as if the subtarget would exist.
This commit adds the Generic subtarget resulting in consistent naming.
~/src/openwrt/openwrt/bin/targets/ipq806x/generic$ ls
openwrt-ipq806x-generic-netgear_d7800-initramfs-uImage
openwrt-ipq806x-generic-netgear-d7800.manifest
openwrt-ipq806x-generic-netgear_d7800-squashfs-factory.img
openwrt-ipq806x-generic-netgear_d7800-squashfs-sysupgrade.bin
CC: John Crispin <john@phrozen.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 853e4dd306)
The 2.4 GHz radio had very poor signal reception (-89 dBm for an AP
sitting 5 m away). By enabling the external amplifier, received signal
has improved to -50 dBm for the same AP.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
(cherry picked from commit e667d6f46b)
Modify GL-AR300M-Lite and GL-AR300M (NOR):
* Include qca9531_glinet_gl-ar300m.dtsi directly
rather than qca9531_glinet_gl-ar300m-nor.dts
* Remove redundant inclusion of gpio.h and input.h
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit f5c7fe2ff0)
So far, WiFi MAC addresses for this device have been set up from
caldata. However, this returns values which do not look like MAC
addresses. They also do not match stock firmware:
wlan0 (5.0): 00:11:22:00:17:D0 from 0x8004
wlan1 (2.4): 00:11:22:00:17:CD from 0x4 (and 0x2e)
It looks like the only valid MAC address on this device is at 0x28.
So, this patch changes setup to calculate addresses based on the
value at 0x28:
lan: *:0A (flash, label)
wan: *:0B (flash + 1)
wifi2: *:0A (flash)
wifi5: *:0C (flash + 2)
Thanks to Roger Pueyo Centelles <roger.pueyo@guifi.net> for
investigating this on his devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit d1072096f4)
The Unifi AC-LR has identical hardware to the Unifi AC-Lite.
The antenna setup is different according to the vendor,
which explains the thicker enclosure.
Therefore, it is helpful to know the exact device variant,
instead of having "Ubiquiti UniFi-AC-LITE/LR".
Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
[fix legacy name in commit message; add old boardname to
SUPPORTED_DEVICES]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 07c1ddf522)
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds correct model detection for UniFi
AC-LR. Previously, said device was incorrectly detected
as UniFi-AC-LITE/MESH.
The Information about the device is stored at 0xC in the EEPROM
partition. It corresponds to the sysid in /etc/board.info of the
Ubiquiti stock firmware.
Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
[adjust naming style of target to existing ones]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 2bc7c519dc)
Signed-off-by: David Bauer <mail@david-bauer.net>
Several Archer Cxx devices were using board-specific LED names in
ar71xx, which were changed to "tp-link:*" in ath79.
This patch adds migration for them.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 53e6cc7a81)
Several devices added to LED migration script will just have their
(old) board name converted to tp-link.
By using a variable for this, the amount of code in the migration
script can be reduced and the chance for typos is reduced.
This patch also introduces the marker for beginning of a pattern
"^" to the regex, so the match is more specific.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 6b0eb84336)
The code line patching ath9k MAC address for this device contains
a wrong number of arguments including an unset "$mac", which
looks like a typo or copy/paste mistake.
This has been introduced already in the device support commit
745dee11ac ("ath79: add support for WD My Net Wi-Fi Range
Extender").
This patch just removes the "$mac" argument, leaving a formally
valid line. (No on-device test has been performed.)
Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 6b53033783)
The ar71xx images for the Ubiquiti NanoStation M (XM) devices use
"nanostation-m" as board name, but the ath79 images are only
compatible with the "nano-m" board name, so sysupgrade complains.
By changing this additional supported device, sysupgrade smoothly
upgrades from ar71xx to ath79.
Ref: openwrt#2418
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit f473ce6f23)
The ar71xx images for the Ubiquiti NanoStation M (XW) devices use
"nanostation-m-xw" as the board name, but the ath79 images are only
compatible with the "nano-m-xw" board name, so sysupgrade complains.
By adding this additional supported device, sysuspgrade smoothly
upgrades from ar71xx to ath79.
Tested on a NanoStation M (XW) running OpenWrt ar71xx r10250-016d1eb.
Ref: https://github.com/openwrt/openwrt/pull/2418
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[removed duplicate DEVICE_VARIANT, removed uneeded nano-m-xw support]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 6dda2ea6ad)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The device did not appear to be reachable unless the connection were
forced to 100Mb or lower. Revert to previously working pll-data.
Also fix the phy-mode to represent the actual state needed for ethernet
to function.
Reported-by: Moritz Schreiber <moritz@mosos.de>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[add remark about phy-mode property]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit ee41b602a2)
edma_read_append_stats() gets called from two places in the driver.
The first place is the kernel timer that periodically updates
the statistics, so nothing gets lost due to overflows.
The second one it's part of the userspace ethtool ioctl handler
to provide up-to-date values.
For this configuration, the use of spin_lock() is not sufficient
and as per:
<https://mirrors.edge.kernel.org/pub/linux/kernel/people/rusty/kernel-locking/c214.html>
the locking has to be upgraded to spin_lock_bh().
Signed-off-by: Masafumi UTSUGI <mutsugi@allied-telesis.co.jp>
[folded patch into 710-, rewrote message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit f1d761f95e)
This corrects the additional boardname for the image metadata to the one
used in ar71xx. The previously present additional entry was never used
on a running system.
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 1a256470e7)
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit fixes TP-Link TL-WDR4900 v1 MAC address assignment.
Previously, the MAC addrss was read for the ethernet from the "config"
partition. However, the content of this partition is dependent on the
firmware which was previously installed on the device.
Switch the MAC address source to the U-Boot partition, where the MAC
address is always present at a fixed partition. The partition was
previously already used for the WiFi MAC-addresses.
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 07e555d873)
Signed-off-by: David Bauer <mail@david-bauer.net>
The default sizes render Device/linksys_audi mage un-flashable.
Restore the pagesize, subpagesize, and blocksize for linksys_audi
from https://github.com/openwrt/archive.
Signed-off-by: Eubert Bao <bunnier@gmail.com>
(cherry picked from commit e11fc8439c)
This fixes a compilation error as follows:
drivers/staging/fsl_qbman/qman_config.c:815:29: error: bitwise comparison
always evaluates to false [-Werror=tautological-compare]
if ((qman_ip_rev & 0xFF00) == QMAN_REV31) {
Signed-off-by: Biwen Li <biwen.li@nxp.com>
(cherry picked from commit 53b73131e9)
The switch port naming in LuCI does not fit the physical numbers
on the front of this device. Since this is confusing, fix it.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
(cherry picked from commit e56e5a454e)
Memory auto-detection for mt7621 has just been added to 19.07
stable branch.
This removes the memory node for the ZBT-WE1326, which will support
revision 5 that has 256MiB RAM (Nanya NT5CC128M16IP-DI) instead of
512MiB (up to revision 4).
ref: #1930
This is taken from master commit a2c19f1d2f ("ramips: dts: drop
memory nodes"), where _all_ memory nodes were removed.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
mt7621 has the following memory map:
0x0-0x1c000000: lower 448m memory
0x1c000000-0x2000000: peripheral registers
0x20000000-0x2400000: higher 64m memory
detect_memory_region in arch/mips/kernel/setup.c only add the first
memory region and isn't suitable for 512m memory detection because
it may accidentally read the memory area for peripheral registers.
This commit adds memory detection capability for mt7621:
1. add the highmem area when 512m is detected.
2. guard memcmp from accessing peripheral registers:
This only happens when some weird user decided to change
kernel load address to 256m or higher address. Since this
is a quite unusual case, we just skip 512m testing and return
256m as memory size.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit 6d91ddf517)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This fixes off-by-one error introduced in commit dc76900021
("kernel: Correctly search for the FIT image in mtd partition.")
Function `mtd_read` starts reading at `offset` and
needs `hdr_len` number of bytes to be available. Suppose
the easiest case when `offset` is `0` and `hdr_len` equals
to `mtd->size` - the `for` loop will not be entered even
when enough bytes are available to be read.
Same happens for any non-zero `offset`, when `hdr_len` is
just enough bytes to be read until `mtd->size` is reached.
Imagine that for example `mtd->size=5`, `offset=4` and
`hdr_len=1`. Then `offset+hdr_len=5` and the check has to
be `offset+hdr_len <= mtd->size`, i.e. `5 <= 5`. The
check for `offset + hdr_len` value needs to be inclusive,
therefore use `<=`.
Fixes: dc76900021 ("kernel: Correctly search for the FIT image in mtd partition.")
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
[adjusted commit ref, fixes tag]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit e0ce80d42a)
Previously all iterations of the loop checked offset=0 in the partition.
Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
(cherry picked from commit dc76900021)
Now that the md5 check is fixed and metadata present, sysupgrade on
ar71xx will complain about device not being supported by the image.
Since the cause is not matching strings for supported devices add them
accordingly.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
(cherry picked from commit a45cf75eca)
This target enforces metadata check so add the necessary information. It
was previously removed because md5 sum check. When using these sysupgrade
images on ar71xx target the check would complain about them not matching.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
(cherry picked from commit 077d06a1a5)
There is md5 sum of whole image embedded in combined-image header which
is checked on sysupgrade. The check will fail for ath79 images which
may have embedded metadata. This is because metadata are appended after
the combined image is created. To allow smooth transition from ar71xx to
ath79, strip metadata before calculating md5 sum for whole image.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
(cherry picked from commit 8b4109c2b4)
The frequency was filled acording the information from datasheet for
particular chip (Winbond 25Q128BVFG). Unfortunately this led to
coruption and introduced bad blocks on the chip. Reducing the frequency
to commonly used in ath79, made the board more stable and no new bad
blocks were spoted.
Fixes: b3a0c97 ("ath79: add support for jjPlus JA76PF2")
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
(cherry picked from commit c1db564cbc)
The relationship between GMAC0 and GMAC1 and the kernel devices
eth0 and eth1 was reversed for many ath79 devices by commit 8dde11d521
ath79: dts: drop "simple-mfd" for gmacs in SoC dtsi
The GL-AR300M-Lite is a single-port device, with the "LAN" port of the
GL-AR300M board unpopulated and its sole port now referenced as eth1,
as a result of commit 8dde11d521. The device was unreachable on
first boot or fresh config.
By changing ð1 (GMAC1) to an MFD, GMAC0 is able to associate with
the phy and is known by the kernel as "eth0".
Thanks to Chuanhong Guo for the suggestion of "simple-mfd"
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
(cherry picked from commit b90ea19860853dd538e704e3e4402686c316e43c)
Previously, the board name for the GL-AR300M-Lite was incorrect
in 02_network, resulting in an unintended, fall-through condition
when initializing the network configuration.
While builds prior to commit 8dde11d521 (merged June 5, 2019)
ath79: dts: drop "simple-mfd" for gmacs in SoC dtsi
functioned properly, the error was noted in resolving first-boot
connectivity issues related to the single-phy nature of the device
and the "swap" of eth0 and eth1 related to that commit.
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
(cherry picked from commit 549ea4dc1878d95ee2b752b8840d75a64a67b679)
The following symbols, selected by the qce driver were removed:
CONFIG_CRYPTO_CBC
CONFIG_CRYPTO_CTR
CONFIG_CRYPTO_DES
CONFIG_CRYPTO_DEV_QCE
CONFIG_CRYPTO_ECB
CONFIG_CRYPTO_NULL
CONFIG_CRYPTO_SEQIV
CONFIG_CRYPTO_XTS
CONFIG_CRYPTO_GF128MUL was removed as well, since it is only needed by
some cipher modes (LRW, GCM), none of which are selected, and it is
packaged as a module.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This adds the CRYPTO_ALG_KERN_DRIVER_ONLY flag to Qualcomm crypto engine
driver algorithms, so that openssl devcrypto can recognize them as
hardware-accelerated.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
[refresh, move to ipq40xx as its the only target right now]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 391b14a892)
This patch removes a typo (extra "0") so that the 'cpu-alert6'
step is triggered once the system reaches 85°C.
Note: Unless the WNDR4700 is placed in an hot oven, the
hardware-monitor will never reach this value.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Replace an old cleanup patch that never made it upstream with the proper
upstream fix. This patch was incompatible with the recent changes that
affected the way that the flow tuple dst entry was used.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commits 442ecce761 and c8933ce533)
Commit fcb41decf6 ("config: enable some useful features on
!SMALL_FLASH devices") enabled netns, which in turn lead to the crash in
the flow offload target.
When the flow offloading framework intends to delete a flow from the
hardware table, it is necessary to retrieve the namespace from
nf_flowtable->ft_net. However, no one ever wrote the namespace into
nf_flowtable->ft_net in advance. So the framework will mistakenly use a
NULL namespace to execute dev_get_by_index_rcu(net, ifindex), leading to
the kernel panic.
Ref: FS#2321
Fixes: fcb41decf6 ("config: enable some useful features on !SMALL_FLASH devices")
Tested-by: Simon Tretter <simon@mediaarchitectu.re>
Signed-off-by: HsiuWen Yen <y.hsiuwen@gmail.com>
[merged patch into offload patch, fix for 4.19, SOB fix, commit subj/msg touches]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry-picked from commit d344591e72)
$(board_name) was providing content on "boardtype" (and optionally
"boardnum") NVRAM values. That function requires & expects more specific
and detailed model name extracted from the /proc/cpuinfo.
Fixes: f12a32630f ("treewide: use the generic board_name function")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The ar40xx driver currently panics in case no QCA807x PHY has been
successfully probed. This happens when the external PHY is still
in reset when probing the ar40xx switch driver.
Note that this patch does not fix the root cause, ar40xx_probe now
simply fails instead of causing a kernel panic due to a nullpointer
dereference.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit e2c084cabc)
We are not sure if 640-bridge-only-accept-EAP-locally.patch is still needed
as a first step, add disable_eap_hack sysfs config to allow to disable it
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
(cherry picked from commit 7d542dc804)
Some ar9344-based devices are using ath9k_patch_fw_mac_crc, which
is meant to generate a checksum, for fixing their ath9k MAC
addresses.
However, those do not have a checksum field, and the calculated
checksum offset would be negative.
This patch will use ath9k_patch_fw_mac function for those devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit f8d8b3f85d)
This adds an easy-installation factory image for the NETGEAR R6220
router. The factory image can either be flashed via the vendor Web-UI or
the bootloader using nmrpflash.
Tested with NETGEAR V1.1.0.86 firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 607dfdf211)
Allow flashing Luxul devices using vendor firmware format. The next step
will be building proper images once they are conirmed to work.
Signed-off-by: Dan Haab <dan.haab@legrand.com>
(cherry picked from commit bc5db7364d)
Now that $UPGRADE_BACKUP is set conditionally there is no need to check
the $UPGRADE_OPT_SAVE_CONFIG anymore. All conditions can be simplified.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit a858db3136)
The UniFi AC LED mapping is currently off. The blue/white LED are used
as WiFi indicators, while the vendor firmware does not feature WiFI
LEDs.
Instead, the LEDs are used to indicate the devices status. Align the LED
mapping to match the vendor firmware as good as possible.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 18fa749df8)
Move the IRQ fix from generic to ar71xx specific.
Other targets like ath79 have specific pathes to delete this code.
This resulted in a build failure on ath79
Fixes: 00d48bcac0 ("ar71xx: Fix potentially missed IRQ handling during
dispatch")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
If both interrupts are set in the current implementation
only the 1st will be handled and the 2nd will be skipped
due to the "if else" condition.
Fix this by using the same approach as done for QCA955x
just below it.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit 9e8c36557cc0582986862f5a36e17adf6db2b90e)
If both interrupts are set in the current implementation
only the 1st will be handled and the 2nd will be skipped
due to the "if else" condition.
Fix this by using the same approach as done for QCA955x
just below it.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This provides TRX validation result to the validation JSON. It also
prevents users from installing broken firmware files.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit c19b9f9a26)
This provides TRX validation result, so final JSON may look like:
{
"tests": {
"fwtool_signature": true,
"fwtool_device_match": true,
"trx_valid": true
},
"valid": true,
"forceable": true
}
It also prevents users from installing broken firmware files, e.g.:
root@OpenWrt:/# sysupgrade -F -n /tmp/TZ
Image metadata not found
Invalid image type. Please use firmware specific for this device.
Image check failed but --force given - will update anyway!
Commencing upgrade. Closing all shell sessions.
Firmware image is broken and cannot be installed
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit e68c1cebd1)
It's a variable set by procd that should replace hardcoded
/tmp/sysupgrade.tgz.
This change requires the most recent procd with the commit 0f3c136
("sysupgrade: set UPGRADE_BACKUP env variable").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 641f6b6c26)
$CONF_TAR shouldn't be assumed to always point to the sysupgrade.tgz.
This change makes code more generic and allows refactoring $CONF_TAR.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 62dbe361a1)
1) Add BACKUP_FILE and use it when copying an archive to be restored
after sysupgrade (on the next preinit).
2) Use CONF_TAR for copying backup prepared by the /sbin/sysupgrade
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit bf39047872)
This reverts commit af91a370de.
As Piotr Dymacz pointed out:
In QCA MIPS based WiSOCs, for first USB interface,
device/host mode can be selected _only_ in hardware
see description of 57c641ba6e
QCA955x and QCA9563, second USB can be switched to device
mode in software (tested and confirmed on real hardware).
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Current ar724x code does the reset only on single pci bus, and
in case of qca9558 writes the wrong register (0x10 vs 0x0c).
This change allows the reset of second pci bus, commonly used in
Archer C7 devices, in case host controller is stuck in reset.
If the resetting controller on boot can solve any other issue it
can be enabled unconditionally by removing reset check before
ar724x_pci_hw_init is called.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
[refreshed to apply cleanly]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit 76d870871cb12fc0c170e5fd23bce568adfaae6d)
Enable flushing of write buffers on qca955x. GPL code has 0x88 reg
defined for PCI flush which is likely an error since the device
freezes on boot. So use DS default value 0xA8 for PCI flush.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
(cherry picked from commit fe9e702dc94ece2a004f6db68d6fb9a94d9437cb)
Switch from ci_usb_setup to generic platform initialization of
usb0 port.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
(cherry picked from commit 36a0cfd24be1cb79f221964ed2bfe12b98befff3)
This backports the only non-cosmetic fix from 6640e1c368
("ramips: clean and improve MAC address setup in 02_network").
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In 555ca422d1 ("ramips: fix D-Link DIR-615 H1 switch port
mapping"), port setup for dir-615-h1 was changed without removing
the old one. This was working as the new one was triggered earlier
than the old one.
(In the meantine, changed sorting during ramips rename patches
actually inversed that order.)
Anyway, just remove the wrong case now.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit e35e4a996e)
ARC FreeStation5 is present twice in MAC address setup.
>From older commits/changes, it is not possible to reconstruct
the correct choice only by reading the annotations.
Thus, remove the second case and keep the first one, so behavior
stays the same (as nobody seems to have complained about it).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit ad4eb2241b)
Image generation is currently failing on builbots due to the following
error:
WARNING: Image file openwrt-19.07-snapshot-r10495-db5164d3d0-ramips-mt7620-wt3020-4M-squashfs-factory.bin is too big
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch was applied to the upstream kernel in version 4.14.135,
remove it from our patches directory.
Fixes: 40379b0ec6 ("apm821xx: fix bogus key-presses on boot")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The AVM Fritz!Box 7530 (and probably other AVM IPQ4019 NAND devices)
has it's caldata not stored consistently, but instead at currently
3 known possible offsets.
As we get a non-zero exit code from fritz_cal_extract, simply try all
three possible offsets on both bootloader partitions, until a matching
caldata for each radio is found.
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit a6f85b81b7)
The net pointer in struct xt_tgdtor_param is not explicitly
initialized therefore is still NULL when dereferencing it.
So we have to find a way to pass the correct net pointer to
ipt_destroy_target().
The best way I find is just saving the net pointer inside the per
netns struct tcf_idrinfo, which could make this patch smaller.
Fixes: 0c66dc1ea3f0 ("netfilter: conntrack: register hooks in netns when needed by ruleset")
Reported-and-tested-by: Tony Ambardar <itugrok@xxxxxxxxx>
Cc: Jamal Hadi Salim <jhs@xxxxxxxxxxxx>
Cc: Jiri Pirko <jiri@xxxxxxxxxxx>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
[Backport for kernel v4.19 and v4.14]
[Bug Link: https://bugzilla.kernel.org/show_bug.cgi?id=204681]
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
(cherry picked from commit 7735cce0c5)
sysupgrade passes image path to platform_check_image() as an argument so
it can be simply accessed using $1
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 76e43c82b5)
[rmilecki: dropping ARGV without this change broke sysupgrade]
Fixes: 6ac62c4b6c ("base-files: don't set ARGV and ARGC")
stage2 passes image path to platform_do_upgrade() as an argument so it
can be simply accessed using $1
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 8b4bc7abe0)
[rmilecki: dropping ARGV without this change broke sysupgrade]
Fixes: 6ac62c4b6c ("base-files: don't set ARGV and ARGC")
This fixes the previously incorrect phy-mode for the OCEDO Ursus GMAC0.
See 62abbd587d ("ath79: correct various phy-mode properties")
for more details.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 7b137e9df9)
There are currently the following issues present for the Netgear R6220,
R6350 and WNDR3700 v5:
- LAN and WAN MAC-addresses are inverted
- WAN MAC-address is off. It are +2 compared to the LAN MAC-address
(R6350 only)
- Switchport order is inverted in LuCi
This commit fixes both these issues by assigning correct MAC-addresses
to LAN and WAN interfaces and defining the switchports with the correct
labels.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 13937a16d4)
This commit switches the default trigger for the WiFi LED from a netdev
trigger on "wlan0" to a wireless-phy based trigger. THis allows the LED
to work, even when the wireless interface is not named "wlan0" without
modifiying the LED settings.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit fa46c9b208)
The MediaTek MT7621 NAND driver currently intransparently shifts NAND
pages when a block is marked as bad. Because of this, offsets for e.g.
caldata and MAC-addresses seem to be off.
This is, howeer, not a task for the mtd NAND driver, as the flash
translation layer is tasked with this.
This patch disables this badblock shifting. This fix was originally
proposed by Jo-Philipp Wich at
https://bugs.openwrt.org/index.php?do=details&task_id=1926
Fixes FS#1926 ("MTD partition offset not correctly mapped when bad
eraseblocks present")
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 527832e54b)
That was a result of accidentally running "sed" twice on some files.
Fixes: 9b9412d55c ("treewide: replace remaining (not working now) $SAVE_CONFIG uses")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 1078de96e3)
This var has been replaced by the $UPGRADE_OPT_UPGRADE_OPT_SAVE_CONFIG
Fixes: f25d164aca ("base-files: pass "save_config" option to the "sysupgrade" method")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 5797fe84a3)
This explicitly lets stage2 know if partitions should be preserved. No
more "touch /tmp/sysupgrade.always.overwrite.bootdisk.partmap" hack.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit b6f4cd57e1)
That function doesn't take any arguments so don't pass anything when
calling it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 670ce65a44)
Calling nand_do_upgrade() from platform_pre_upgrade() was obsoleted in
the commit 30f61a34b4 ("base-files: always use staged sysupgrade").
This change brings bcm53xx in sync with other targets and allows
dropping backward compatibility code. It shouldn't change any user
visible behavior.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit ccf8a8e863)
It's a simple typo in the DNS file, which was pretty serious.
No scripts were working properly. Fix it up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[integrate upstream patch into openwrt target]
(cherry picked from commit 5470e928d0)
"There are often transient line events when
the system is powered up and initialized and it
is often necessary for the gpio_chip driver to
clear any interrupt flags in hardware before
setting up the gpio chip, especially the
irqchip portions of it."
<http://lists.infradead.org/pipermail/openwrt-devel/2019-June/017630.html>
This patch adds a fix for the APM821XX's interrupt
controller to clear any bogus pending toggled
interrupts that happens on various APM821XX boards
on boot.
The patch also changes the debouce-interval from the
default 5ms debounce interval to 60ms all around.
The default setting caused on occasions that the button
state became stuck in a pressed state, even though the
button was released.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(backported from commit 971f31bedc)
The DIR-685 has the MAC addresses in the RedBoot code just like
DNS-313. Check some magic numbers to determine that the MAC
address is where we want it and extract it from RedBoot.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[replaced ifconfig with ip, ! -z = -n, added string quotes]
(cherry picked from commit 86098ea87e)
The DNS-313 isn't the only special board so let's bite the
bullet and create a case ladder in preparation for DIR-685.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [refreshed]
(cherry picked from commit 38d85d2c9f)
This simplifies the ethernet address extraction script
by using standard library functions to locate the MTD
partitions and extract ethernet address from a binary
offset location in the flash. Furthermore, the aging
ifconfig is replaced by the ip tool, which will now
assign the MAC addresses.
Suggested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[ifconfig replacement, use -n instead of ! -z,
-n requires string to be quoted within the test brackets,
drop prepended "x" in check, add quotes, make local
variables local, kill whitespaces]
(cherry picked from commit cd6c3535cd)
CONFIG_PACKET is a important feature to have.
The Packet protocol is used by applications which
communicate directly with network devices without
an intermediate network protocol implemented in
the kernel, e.g. tcpdump and ip.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit bdbb679adb)
Without this patch, an extra entry appears for AR9287 GPIO
that duplicates WLAN LED but in fact drives nothing:
gpiochip1: GPIOs 502-511, ath9k-phy0:
gpio-502 ( |netgear:blue:wlan ) out hi
gpio-503 ( |netgear:amber:test ) out hi
gpio-504 ( |netgear:green:power ) out lo
gpio-505 ( |rfkill ) in hi
gpio-507 ( |wps ) in hi
gpio-508 ( |reset ) in hi
gpio-510 ( |ath9k-phy0 ) out hi <===!
The pin pointed above is default LED GPIO (8) for AR9287.
For WNR2200 it is not connected anywhere - pin 0 drives blue WLAN
LED instead - but initialization code is missing that information.
This fix calls ap9x_pci_setup_wmac_led_pin() function at device
setup, forcing WLAN LED pin to be 0 and removing redundant entry.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
The button is labelled reboot/restore in documentation, and has always
been used for that. Naming it WPS has always been wrong.
Signed-off-by: Karl Pálsson <karlp@etactica.com>
[matched author with SoB]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The command line enforced by the kernel is harmful, we want to
use the command line passed from the device tree. This is
especially important for the SQ201, Teltonika RUT and WBD111
which has a console set to 115200n8 and not 19200n8 like all
the others, so their consoles will be confusingly changing
baudrate between boot loader and kernel. The setting in the
device tree corresponds to what the boot loader is using.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit ea44ed5f38)
tx_size was just declared above and set to BIT(tx->order)
Use the declaration instead, which could avoid a pointer deref
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit 6852eab58236e3991f5d73f211018dfef01f2a64)
Backport of a4eef43a12 ("ath79: ag71xx: replace alloc_etherdev with devm_alloc_etherdev")
combined with the initial changes from John Crispin.
Simplifies the code a lot by using the Managed dev API.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Backport of 4eaa3626a8 ("ath79: ag71xx: pass correct device pointer to dma functions")
While 4.14 does not contain the warnings,
it still makes sense to use the proper pointers here.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
All other instances of this identical declaration fetch the
value directly from the ring_order.
Also do it here.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Refreshed all patches.
Also add a missing symbol for x86 which got used now in this bump.
- ISCSI_IBFT
Compile-tested on: cns3xxx, x86_64
Runtime-tested on: cns3xxx, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This will reduce the size of the kernel if CONFIG_CC_OPTIMIZE_FOR_SIZE is
set like for all targets with small_flash feature flag.
I haven't seen any changes for an ARM64 target which optimizes the
kernel for speed instead.
On the ath79/tiny target the uncompressed kernel size was reduced by
3.2% and the compressed kernel size by 2.1%
kernel size with CONFIG_OPTIMIZE_INLINING=n
4346412 build_dir/target-mips_24kc_musl/linux-ath79_tiny/vmlinux
1391169 build_dir/target-mips_24kc_musl/linux-ath79_tiny/tplink_tl-wr941-v4-kernel.bin
Kernel size with CONFIG_OPTIMIZE_INLINING=y
4212396 build_dir/target-mips_24kc_musl/linux-ath79_tiny/vmlinux
1362051 build_dir/target-mips_24kc_musl/linux-ath79_tiny/tplink_tl-wr941-v4-kernel.bin
This change is currently pending for kernel 5.2 and already in
linux-next, this updates our patch to match the upstream version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6dac1c0a9b)
Unconditionally execute the final case statement, even if the disk layout
changed. This is necessary, to keep the original Turris Omnia flash
instructions working: The disk layout WILL change, when switching from
TurrisOS to OpenWRT. Without updating the uboot environment at the same
time, the user would end up with an unbootable system.
Fixes commit 2e5a0b81ec ("mvebu: sysupgrade: sdcard: keep user added ...")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
This commit fixes regression on Linksys WRT1900 (Mamba) where this device
doesn't have USB 3.0 controller integrated in SoC, instead it has Etron
EJ168 connected to PCIe lane. Previously enabled in kernel 4.4 and 4.9,
was lost in transition to 4.14.
Fixes: 4ccad92 ("mvebu: Add support for kernel 4.14")
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This commit unifies the LED mapping of the AVM Fritz!Box routers, which
have a combined Power/DSL LED.
With the stock firmware, the Power LED has the following
characteristics:
- Blink when DSL sync is being established
- Solid when DSL sync is present
We can't completely resemble this behavior in OpenWrt. Currently, the
Power LED is completely off, when DSL sync is missing. This is not
really helpful, as a user might have the impression, that he bricked his
device.
Instead, map the Info-LED to the state of the DSL connection.
There is no consistent behavior for the Info-LED in the stock
firmware, as the user can set it's function by himself. The DSL
connection state is one possible option for the Info LED there.
Also use the red Power LED to indicate a running upgrade, in case the
board has a two-color Power LED.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3032bf7f89)
This reverts commit 2b074654b0.
Due to popular demand, I've decided to revert this commit after
deliberating with Petr. This means that 19.07 will ship ath79 binary
images after all.
We do however consider the ath79 target on Kernel 4.14 in the 19.07
branch to be beta quality at best.
Acked-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This adds the led-upgrade alias for the AVM Fritz!Box 7412 to indicate a
running firmware upgrade.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 920abb9b58)
The AVM Fritz!Box 7412 does not use the VMMC part of the Lantiq chip but
rather a proprietary solution based on the DECT chip for the FXS ports.
Therefore, the second VPE can be enabled for use with OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 891a700759)
The AVM FRITZ!Box 7412 buttons are both active low, which is currently
incorrectly defined in the device-tree.
This leads to the device booting directly into failsafe.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit c12947b39e)
This commit selects wpad-basic for the FRITZ!Box 7312 and 7412 as
wpad-mini is only selected on boards with small flash.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
[add short description]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit c3c3cd5e4a)
ar71xx got lost during final rebase ..
Fixes: c8a6ce71e4 ("ar71xx/ath79: ag71xx: init rings with GFP_KERNEL")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Upstream commit 246902bdf562d45ea3475fac64c93048a7a39f01
Which contains following explanation:
--
There is no need to use GFP_ATOMIC here, GFP_KERNEL should be enough.
The 'kcalloc()' just a few lines above, already uses GFP_KERNEL.
--
Looking at the code, all other descriptors also use plain GFP_KERNEL
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
WLAN0 and the unused LED are currently swapped. Fix this, so the LED
behavior matches the other OCEDo devices.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit a3a2b4857e)
The Aerohive HiveAP 121 has the wrong PLL value set for Gigabit speeds,
leading to packet-loss. 10M and 100M work fine.
This commit sets the Gigabit Ethernet PLL value to the correct value,
fixing packet loss.
Confirmed with iperf and floodping.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit cb49e46a8a)
commit e09da0169a ("ar71xx: fix Mikrotik board detection")
was generated based on testing a rb-912 board, on which detection failed.
Testing on more hardware shows something fun:
machine : MikroTik RouterBOARD 922UAGS-5HPacD
machine : Mikrotik RouterBOARD 912UAG-5HPnD
Both lowercase and uppercase are used.
So ensure we support both now ..
Fixes: e09da0169a ("ar71xx: fix Mikrotik board detection")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit 845b2a1cfe)
- add uart rom script address in header of sdma firmware to support
the uart driver of latest kernel working well while old firmware
assume ram script used for uart driver as NXP internal legacy
kernel.
- add multi-fifo SAI/PDM scripts.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit 819b6345a206ad182dd3c2d786a3d7f04e33f751)
In order to prevent build of images for this release as ath79 is going
to deprecate ar71xx in the next release.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fix a typo in the machine type being extracted from /proc/cpuinfo
which causes all Mikrotik board to be undetected properly.
This lead to sysupgrade issues and probably some others too.
Fixes: 76c963bb01 ("ar71xx: base-files: fix board detect on new MikroTik devices")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Update WLAN LED colour identifier for both interfaces on Archer C7
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
(cherry picked from commit 65762cdd22)
Move system LED board definitions of Archer C5/C7 to reflect
actual system LED colour used
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
(cherry picked from commit a73934fc9a)
All leds on these boards are green. v1 has RFKILL GPIO 23 for production
units (it had GPIO 13 only for test phase units, and these are rather
very rare to find). As for the previous attempt to fix this and revert
due to WDR boards have blue leds, it was wrong: WDR board does not use
common setup (false).
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
(cherry picked from commit c79c001b59)
Base address for USB0 has changed from 0x18116c94 on AR934X
to 0x18116d94 on QCA9558. CP Typo remained for years here...
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
(cherry picked from commit fd5aa19480)
SoC: MediaTek MT7621AT
RAM: 128M (Winbond W631GG6KB-15)
FLASH: 16MB (Spansion S25FL128SA)
WiFi: MediaTek MT7603EN bgn 2SS
WiFi: MediaTek MT7612EN nac 2SS
BTN: Reset - WPS
LED: - Power
- LAN {1-4}
- WAN
- WiFi 2.4 GHz
- WiFi 5 GHz
- USB
UART: UART is present next to the Power LED.
TX - RX - GND - 3V3 / 57600-8N1
3V3 is the nearest one to the Power LED.
Installation
------------
Via TFTP:
1. Set your computers IP-Address to 192.168.1.75.
2. Power up the Router with the Reset button pressed.
3. Release the Reset button after 5 seconds.
4. Upload OpenWRT sysupgrade image via TFTP:
> tftp -4 -v -m binary 192.168.1.1 -c put <IMAGE>
Via SSH:
Note: User/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt sysupgrade image via scp:
> scp owrt.bin admin@192.168.1.1:/tmp
4. Connect via SSH to the router.
> ssh admin@192.168.1.1
5. Write the OpenWrt image to flash.
> mtd-write -i /tmp/owrt.bin -d linux
6. Reboot the router
> reboot
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 14e0e4f138)
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN: 1x Reset
LED: 1x LED Power (non-controllable)
1x LED Status (internal)
1x LED LAN (controlled by PHY)
1x LED WLAN
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to external-LED header.
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit cb3cd52694)
fixes intermittent loss of connectivity on 1Gbit port, with log message:
> 803x_aneg_done: SGMII link is not ok
Thanks to David Bauer for pointing me in the right direction.
I just had to figure out the right bus_id, which you find in this log:
> ag71xx ag71xx.1: connected to PHY at gpio-1:00 [uid=004dd074,
driver=Atheros 8031 ethernet]
Fixes FS#2236
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
[Wrapped commit message - Fixed whitespace erors]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 2a7519e29d)
Image generation is currently failing on builbots due to the following
error:
WARNING: Image file [...] mt7620-ex2700-squashfs-factory.bin is too big
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Many Atom-based embedded/industrial x86 boards can't run 64bit operating
systems due to either processor or board firmware limitations, but they
have modern interfaces (PCIe) or have modern Intel gigabit controllers
onboard. With the current default package selection for x86 Generic
target their network won't work.
Add the modern gigabit network modules needed or most likely going to be
used as add-in cards, similar to what is the list on x86_64 target.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[fixed whitespace issue]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit bb27cde257)
Image generations is currently failing on builbots due to the following
errors:
mkfwimage -B XS2 -v XS2 [...] ath25-ubnt2-squashfs-sysupgrade.bin
ERROR: Failed creating firmware layout description - error code: -2
mkfwimage -B XS5 -v XS5 [...] ath25-ubnt5-squashfs-sysupgrade.bin
ERROR: Failed creating firmware layout description - error code: -2
That cryptic -2 error simply means, that kernel+rootfs doesn't fit into
the firmware partition.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In ath79, identifiers tplink_tl-wdr3600 and tplink_tl-wdr4300 have
been used while most other TP-Link devices include the revision.
Although there actually is only one major revision of these
devices, they bear the revision on their bottom (v1.x). TP-Link
also refers to the devices as V1 on its web page.
This patch thus adds -v1 to both so it is more consistent
with other devices and with what you would expect from reading
the on-device sticker and the support pages.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
It was reported in FS#2385, that Carambola2 doesn't currently have
working watchdog so fix it by adding watchdog node.
Ref: FS#2385
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 0893f28e19)
While flashing lots of RB2011 devices, I noticed that
some of them refused to boot properly, failing over the NAND parameters.
Checking in detail shows that some device seem to use another NAND flash
which only support standard 2048-byte pages, without 512-byte subpage support.
This commit disables usage of these small subpage completely.
Advantages:
- Both NAND's with(out) subpage support are working now
- The nand speed increases a bit (measured roughly 1%) in typical usecases
Disadvantages:
- The maximum storage capacity decreases by ~0.2%
as small changes can consume a full page (2048 bytes) now.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This is already included in newer upstream. Needed to build BPF programs
using the MIPS kernel include files.
Without this patch, clang fails with "#error Use a Linux compiler or
give up." in sgidefs.h when building BPF programs.
Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
(cherry-picked from commit 7d96c301d6)
After commit 1e41de2f48 ("mpc85xx: convert TL-WDR4900 v1 to simpleImage")
XZ compression of zImage was enabled. This change exposed a problem with
the HiveAP-330 images, which was fixed by foregoing the compression on
the kernel altogether with commit 98089bb8ba
("mpc85xx: Use uncompressed kernel on the HiveAP-330").
This patch adds back the gzip compression of the kernel image by
utilizing the generic OpenWRT uImage method instead of relying on
the PowerPC bootwrapper script that did it previously.
Compile-tested: p1020/hiveap-330
Tested-by: Chris Blake <chrisrblake93@gmail.com> [run-tested]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[filled in even more text]
While moving common used parts to dtsi files, the was disabled by
default but not enabled for all boards using the STP.
Fixes: f519fea4c6 ("lantiq: kernel 4.14: cleanup dts files")
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Apply the same approach as in commit 3b53d6fdbc ("ar71xx: fix pci irq
init on kernel 4.14") to fix IRQ initialization for ath79-based chipsets
on rb4xx.
Ref: PR#2182
Acked-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: W. Michael Petullo <mike@flyn.org>
[commit ref fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 8c7d6c47a7)
When the non-generic espressobin targets were added these board checks
were not updated. One side effect of this is that config is not saved
during an upgrade of -emmc,-v7, or -v7-emmc devices.
Signed-off-by: Brett Mastbergen <bmastbergen@untangle.com>
(cherry picked from commit 95c1dc5e86)
When targets for multiple ESPRESSObin devices were added, not all
files were updated which means any ESPRESSObin version beside generic
won't have proper networking, sysupgrade and uboot-env. This patch
fixes the issue.
* fixup network detection
* fixup uboot-env
* fixup platform.sh for sysupgrade
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
(cherry picked from commit bc47285cb3)
Not all versions of ESPRESSObin require SD card, but can
be booted from the internal emmc flash (mmc dev 1) instead.
Add a simple check in the bootscript to see which mmc device
is detected and boot from it using mmcdev variable.
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
(cherry picked from commit 008b41b9b0)
An aquantia phy patch which dropped pause frame support was
missing when integrated LSDK-19.03 kernel patches into OpenWrt.
Without this patch, LS1043A 10G port would not work. So apply it.
Patch link
https://source.codeaurora.org/external/qoriq/qoriq-components/
linux/commit/?h=linux-4.14&id=66346b115818365cfaf99d292871b19f0a1d2850
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
"There are often transient line events when
the system is powered up and initialized and it
is often necessary for the gpio_chip driver to
clear any interrupt flags in hardware before
setting up the gpio chip, especially the
irqchip portions of it."
<http://lists.infradead.org/pipermail/openwrt-devel/2019-June/017630.html>
This patch adds a fix for the APM821XX's interrupt
controller to clear any bogus pending toggled
interrupts that happens on various APM821XX boards
on boot.
The patch also changes the debouce-interval from the
default 5ms debounce interval to 60ms all around.
The default setting caused on occasions that the button
state became stuck in a pressed state, even though the
button was released.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
It seems that newer builds of OpenWRT have a gzip kernel
larger than 2MB~, which for some reason fails to boot on this board.
However, we have 8MB of kernel space and currently the uncompressed
kernel is 6.5MB~, so we have some space to grow until a better
solution is worked out.
Before:
## Booting kernel from Legacy Image at ee840000 ...
Image Name: Linux-4.19.53
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 2315724 Bytes = 2.2 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02000000 ...
Image Name: OpenWrt fake ramdisk
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux RAMDisk Image (uncompressed)
Data Size: 0 Bytes = 0 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at ec000000
Booting using the fdt blob at 0xec000000
Uncompressing Kernel Image ... Error: Bad gzipped data
GUNZIP: uncompress, out-of-mem or overwrite error -
must RESET board to recover
Loading Ramdisk to 10000000, end 10000000 ... OK
Loading Device Tree to 00ffa000, end 00fffc78 ... OK
ft_fixup_l2cache: FDT_ERR_NOTFOUND
After:
## Booting kernel from Legacy Image at ee840000 ...
Image Name: POWERPC OpenWrt Linux-4.19.53
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux Kernel Image (uncompressed)
Data Size: 6724584 Bytes = 6.4 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02000000 ...
Image Name: OpenWrt fake ramdisk
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux RAMDisk Image (uncompressed)
Data Size: 0 Bytes = 0 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at ec000000
Booting using the fdt blob at 0xec000000
Loading Kernel Image ... OK
OK
Loading Ramdisk to 10000000, end 10000000 ... OK
Loading Device Tree to 00ffa000, end 00fffc78 ... OK
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [75 cpl limit]
When OEM volumes are present in the [alt_]firmware partition,
sysupgrade will write a new kernel, but will fail to write
the root file system. The next boot will hang indefinitely
Waiting for root device /dev/ubiblock0_0...
Modified ipq40xx/base-files/lib/upgrade/linksys.sh
to remove both `squashfs` and `ubifs` if found
on the target firmware partition's UBI device.
Run-tested-on: Linksys EA8300
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[applied some shellcheck suggestions as well]
Follow upstream changes - header file changes
no executable difference at all
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit 5273fb6b21)
Move all MikroTik devices to new function to increase script execution
speed.
Machine name in new version of MikroTik RouterBOARD devices add "RB"
before model name:
Old machine name: MikroTik RouterBOARD 951Ui-2nD
New: MikroTik RouterBOARD RB951Ui-2nD
So this patch should fix it for all currently supported MikroTik boards.
Tested-by: Cezary Jackiewicz <cezary@eko.one.pl> [wAP R-2nD]
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[rebased,commit message facelift,script fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[spotted missing 922UAGS-5HPacD]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Refreshed all patches.
Altered patches:
- 816-pcie-support-layerscape.patch
This patch also restores the initial implementation
of the ath79 perfcount IRQ issue. (78ee6b1a40)
It was wrongfully backported upstream initially and got reverted now.
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
err_free_stats has been deprecated. Replace with err_netdev.
Compile-tested on: mvebu
Runtime-tested on: mvebu
Fixes: 4089df4f4b ("kernel: bump 4.14 to 4.14.125 (FS#2305 FS#2297)")
Signed-off-by: George Amanakis <gamanakis@gmail.com>
[altered hashes]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit 1e3800df18)
It's needed for applying some hardware quirks. This fixes:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/dmi.c:60:20: error: 'DMI_PRODUCT_SKU' undeclared here (not in a function); did you mean 'DMI_PRODUCT_UUID'?
DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "T8"),
Fixes: c52054e568 ("mac80211: brcm: backport remaining brcmfmac 5.2 patches")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 4d11c4c378)
Memory is allocated with devm_kzalloc() on every page program
and leaks until device is closed (which never happens).
Convert to kzalloc() and handle error paths manually.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Refreshed all patches.
This bump contains upstream commits which seem to avoid (not properly fix)
the errors as seen in FS#2305 and FS#2297
Altered patches:
- 403-net-mvneta-convert-to-phylink.patch
- 410-sfp-hack-allow-marvell-10G-phy-support-to-use-SFP.patch
Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* Remove testing patches for kernel version 4.19
* remove targets ar7, ixp4xx, orion
Those targets are still on kernel 4.9, patches for 4.14 were not ready
in time. They may be readded once people prepare and test patches for
kernel 4.14.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
01_leds has several redundant LED-cases. This commit cleans
up the file by merging these cases into shared cases.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
The TP-Link Archer C25 is a low-cost dual-band router.
Specification:
- CPU: Atheros QCA9561 775 MHz
- RAM: 64 MB
- Flash: 8 MB
- Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887
- NET: 5x 10/100 Mbps Ethernet
Some LEDs are controlled by an additional 74HC595 chip, but not
all of them as e.g. for the C59.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ASUS RP-N53 and Buffalo WHR-600D use RT5592 for 5GHz wireless
After commit 367813b9b1 the driver for RT5592 (rt2800pci)
is not selected by default anymore, which broke their 5GHz wireless
Add it back to device packages
Fixes: 367813b9b1 ("ramips: mt7620: fix dependencies")
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
When upgrading a TP-Link Archer C7 v2 from ar71xx to ath79,
the 5ghz radio stops working because the device path changed.
Some people subtitute the unsupported QCA9880v1 in the Archer v1
with supported QCA9880v2 radio. Since the stock radio doesn't
work, so it's safe to apply the change also for the Archer v1
images as well.
Also this patch renames the migration file and variables from
wmac to wifi.
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[removed comment, added return 0 (not that it matters since uci is
clever, see 00-wmac-migration thread), reworded commit message]
This patch harmonizes the label and alias for art partitions
across ath79. Since lower case seems to be more frequent, use that
consistently.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In commit c3a8518 eth0 and eth1 have been swapped for some devices,
but 11-ath10k-caldata has not been updated.
Instead of fixing this by swapping eth0/eth1, this patch will read
addresses from flash (as done for several devices already) so
adjustments due to eth order become obsolete.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The info/product-info partition, which frequently contains MAC
adresses, is typically assigned the 'info' alias in DTS, but
then labelled with 'info', 'product-info' or 'config'.
This leads to different aliases if used for setting MAC adresses
in DTS compared to when using e.g. mtd_get_mac_binary. Occationally,
also multiple switch-case entries are used just because of different
labelling.
This patch relabels those partitions in ath79 to consistently use
'info'.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Converts the TP-Link WDR4900 v1 to use the simpleImage in the
hopes of prolonging the life of the device. While at it,
the patch makes the fdt.bin an ARTIFACT and sets the KERNEL_SIZE
to 2684 KiB as a precaution since the stock u-boot is using a
fixed kernel size.
Note: Give the image some time, it will take much longer to
extract and boot.
[tested for 4.14/4.19]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Co-authored-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
In commit d2e18dae28 ("kirkwood: cleanup image build code") the image
build code was refactored, setting KERNEL_IN_UBI=0 which doesn't work as
the KERNEL_IN_UBI needs to be unset in order to make it working as
intended, which leads to factory images with two kernels in them:
binwalk --keep-going openwrt-kirkwood-cisco_on100-squashfs-factory.bin
MD5 Checksum: c33e3d1eb0cb632bf0a4dc287592eb70
DECIMAL HEX DESCRIPTION
-------------------------------------------------------------------------------
0 0x0 uImage header [...] "ARM OpenWrt Linux-4.14.123"
5769216 0x580800 uImage header [...] "ARM OpenWrt Linux-4.14.123"
Cc: Mathias Kresin <dev@kresin.me>
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=2285
Fixes: d2e18dae28 ("kirkwood: cleanup image build code")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The "bridge allow reception on disabled port" implementation
was broken after these commits:
08802d93e2 ("kernel: bump 4.19 to 4.19.37")
b765f4be40 ("kernel: bump 4.14 to 4.14.114")
456f486b53 ("kernel: bump 4.9 to 4.9.171")
This leads to issues when for example WDS is used, tied to a bridge:
[ 96.503771] wlan1: send auth to d4:5f:25:eb:09:82 (try 1/3)
[ 96.517956] wlan1: authenticated
[ 96.526209] wlan1: associate with d4:5f:25:eb:09:82 (try 1/3)
[ 97.086156] wlan1: associate with d4:5f:25:eb:09:82 (try 2/3)
[ 97.200919] wlan1: RX AssocResp from d4:5f:25:eb:09:82 (capab=0x11 status=0 aid=1)
[ 97.208706] wlan1: associated
[ 101.312913] wlan1: deauthenticated from d4:5f:25:eb:09:82 (Reason: 2=PREV_AUTH_NOT_VALID)
It seems upstream introduced a new patch, [1]
so we have to reimplement these patches properly:
target/linux/generic/pending-4.9/150-bridge_allow_receiption_on_disabled_port.patch
target/linux/generic/pending-4.14/150-bridge_allow_receiption_on_disabled_port.patch
target/linux/generic/pending-4.19/150-bridge_allow_receiption_on_disabled_port.patch
[1] https://lkml.org/lkml/2019/4/24/1228
Fixes: 08802d93e2 ("kernel: bump 4.19 to 4.19.37")
Fixes: b765f4be40 ("kernel: bump 4.14 to 4.14.114")
Fixes: 456f486b53 ("kernel: bump 4.9 to 4.9.171")
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
[updated commit message and title]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
ctinfo is a new tc filter action module. It is designed to restore
information contained in firewall conntrack marks to other packet fields
and is typically used on packet ingress paths. At present it has two
independent sub-functions or operating modes, DSCP restoration mode &
skb mark restoration mode.
The DSCP restore mode:
This mode copies DSCP values that have been placed in the firewall
conntrack mark back into the IPv4/v6 diffserv fields of relevant
packets.
The DSCP restoration is intended for use and has been found useful for
restoring ingress classifications based on egress classifications across
links that bleach or otherwise change DSCP, typically home ISP Internet
links. Restoring DSCP on ingress on the WAN link allows qdiscs such as
but by no means limited to CAKE to shape inbound packets according to
policies that are easier to set & mark on egress.
Ingress classification is traditionally a challenging task since
iptables rules haven't yet run and tc filter/eBPF programs are pre-NAT
lookups, hence are unable to see internal IPv4 addresses as used on the
typical home masquerading gateway. Thus marking the connection in some
manner on egress for later restoration of classification on ingress is
easier to implement.
Parameters related to DSCP restore mode:
dscpmask - a 32 bit mask of 6 contiguous bits and indicate bits of the
conntrack mark field contain the DSCP value to be restored.
statemask - a 32 bit mask of (usually) 1 bit length, outside the area
specified by dscpmask. This represents a conditional operation flag
whereby the DSCP is only restored if the flag is set. This is useful to
implement a 'one shot' iptables based classification where the
'complicated' iptables rules are only run once to classify the
connection on initial (egress) packet and subsequent packets are all
marked/restored with the same DSCP. A mask of zero disables the
conditional behaviour ie. the conntrack mark DSCP bits are always
restored to the ip diffserv field (assuming the conntrack entry is found
& the skb is an ipv4/ipv6 type)
e.g. dscpmask 0xfc000000 statemask 0x01000000
|----0xFC----conntrack mark----000000---|
| Bits 31-26 | bit 25 | bit24 |~~~ Bit 0|
| DSCP | unused | flag |unused |
|-----------------------0x01---000000---|
| |
| |
---| Conditional flag
v only restore if set
|-ip diffserv-|
| 6 bits |
|-------------|
The skb mark restore mode (cpmark):
This mode copies the firewall conntrack mark to the skb's mark field.
It is completely the functional equivalent of the existing act_connmark
action with the additional feature of being able to apply a mask to the
restored value.
Parameters related to skb mark restore mode:
mask - a 32 bit mask applied to the firewall conntrack mark to mask out
bits unwanted for restoration. This can be useful where the conntrack
mark is being used for different purposes by different applications. If
not specified and by default the whole mark field is copied (i.e.
default mask of 0xffffffff)
e.g. mask 0x00ffffff to mask out the top 8 bits being used by the
aforementioned DSCP restore mode.
|----0x00----conntrack mark----ffffff---|
| Bits 31-24 | |
| DSCP & flag| some value here |
|---------------------------------------|
|
|
v
|------------skb mark-------------------|
| | |
| zeroed | |
|---------------------------------------|
Overall parameters:
zone - conntrack zone
control - action related control (reclassify | pipe | drop | continue |
ok | goto chain <CHAIN_INDEX>)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make suitable adjustments for backporting to 4.14 & 4.19
and add to SCHED_MODULES_FILTER
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
All patches of LSDK 19.03 were ported to Openwrt kernel.
We still used an all-in-one patch for each IP/feature for
OpenWrt.
Below are the changes this patch introduced.
- Updated original IP/feature patches to LSDK 19.03.
- Added new IP/feature patches for eTSEC/PTP/TMU.
- Squashed scattered patches into IP/feature patches.
- Updated config-4.14 correspondingly.
- Refreshed all patches.
More info about LSDK and the kernel:
- https://lsdk.github.io/components.html
- https://source.codeaurora.org/external/qoriq/qoriq-components/linux
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to convert to use TF-A for firmware.
- Use un-swapped rcw since swapping will be done in TF-A.
- Use u-boot with TF-A defconfig.
- Rework memory map for TF-A introduction.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The WAN port has the wrong configuration in the kernel for the DVA-G3810BN/TL
The WAN port uses the internal phy, but it isn't enabled at the kernel board data.
Fix it.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This reverts commit 7c50182e0c.
Produces build error:
Package kmod-sched is missing dependencies for the following libraries:
nf_conntrack.ko
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
ctinfo is a new tc filter action module. It is designed to restore
information contained in firewall conntrack marks to other packet fields
and is typically used on packet ingress paths. At present it has two
independent sub-functions or operating modes, DSCP restoration mode &
skb mark restoration mode.
The DSCP restore mode:
This mode copies DSCP values that have been placed in the firewall
conntrack mark back into the IPv4/v6 diffserv fields of relevant
packets.
The DSCP restoration is intended for use and has been found useful for
restoring ingress classifications based on egress classifications across
links that bleach or otherwise change DSCP, typically home ISP Internet
links. Restoring DSCP on ingress on the WAN link allows qdiscs such as
but by no means limited to CAKE to shape inbound packets according to
policies that are easier to set & mark on egress.
Ingress classification is traditionally a challenging task since
iptables rules haven't yet run and tc filter/eBPF programs are pre-NAT
lookups, hence are unable to see internal IPv4 addresses as used on the
typical home masquerading gateway. Thus marking the connection in some
manner on egress for later restoration of classification on ingress is
easier to implement.
Parameters related to DSCP restore mode:
dscpmask - a 32 bit mask of 6 contiguous bits and indicate bits of the
conntrack mark field contain the DSCP value to be restored.
statemask - a 32 bit mask of (usually) 1 bit length, outside the area
specified by dscpmask. This represents a conditional operation flag
whereby the DSCP is only restored if the flag is set. This is useful to
implement a 'one shot' iptables based classification where the
'complicated' iptables rules are only run once to classify the
connection on initial (egress) packet and subsequent packets are all
marked/restored with the same DSCP. A mask of zero disables the
conditional behaviour ie. the conntrack mark DSCP bits are always
restored to the ip diffserv field (assuming the conntrack entry is found
& the skb is an ipv4/ipv6 type)
e.g. dscpmask 0xfc000000 statemask 0x01000000
|----0xFC----conntrack mark----000000---|
| Bits 31-26 | bit 25 | bit24 |~~~ Bit 0|
| DSCP | unused | flag |unused |
|-----------------------0x01---000000---|
| |
| |
---| Conditional flag
v only restore if set
|-ip diffserv-|
| 6 bits |
|-------------|
The skb mark restore mode (cpmark):
This mode copies the firewall conntrack mark to the skb's mark field.
It is completely the functional equivalent of the existing act_connmark
action with the additional feature of being able to apply a mask to the
restored value.
Parameters related to skb mark restore mode:
mask - a 32 bit mask applied to the firewall conntrack mark to mask out
bits unwanted for restoration. This can be useful where the conntrack
mark is being used for different purposes by different applications. If
not specified and by default the whole mark field is copied (i.e.
default mask of 0xffffffff)
e.g. mask 0x00ffffff to mask out the top 8 bits being used by the
aforementioned DSCP restore mode.
|----0x00----conntrack mark----ffffff---|
| Bits 31-24 | |
| DSCP & flag| some value here |
|---------------------------------------|
|
|
v
|------------skb mark-------------------|
| | |
| zeroed | |
|---------------------------------------|
Overall parameters:
zone - conntrack zone
control - action related control (reclassify | pipe | drop | continue |
ok | goto chain <CHAIN_INDEX>)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make suitable adjustments for backporting to 4.14 & 4.19
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This patch removes 202-reduce_module_size.patch which is causing missing
debug symbols in kernel modules, leading to unusable
kernel-debug.tar.bz2 on all platforms, making debugging of release
kernel crashes difficult.
Cc: Felix Fietkau <nbd@nbd.name>
Acked-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Specifications:
- SoC: MT7628DAN (MT7628AN with 64MB built-in RAM)
- Flash: 8M SPI NOR
- Ethernet: 5x 10/100Mbps
- WiFi: 2.4G: MT7628 built-in
5G: MT7612E
- 1x miniPCIe slot for LTE modem (only USB pins connected)
- 1x SIM slot
Flash instruction:
U-boot has a builtin web recovery page:
1. Hold the reset button while powering it up
2. Connect to the ethernet and set an IP in 192.168.1.0/24 range
3. Open your browser and upload firmware through http://192.168.1.1
Note about the LTE modem:
If your router comes with an EC25 module and it doesn't show up
as a QMI device, you should do the following to switch it to QMI
mode:
1. Install kmod-usb-serial-option and a terminal software
(e.g. minicom or screen). All 4 serial ports of the modem
should be available now.
2. Open /dev/ttyUSB3 with the terminal software and type this
AT command: AT+QCFG="usbnet",0
3. Power-cycle the router. You should now get a QMI device
recognized.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Specifications:
- Atheros AR9331 (400 MHz)
- 64 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 1T1R 2.4 Wlan (AR9331)
- 2x 10/100 Mbps Ethernet
- 3x LEDs, 1x gpio button
- 1x USB 2.0, 5V
- UART over usb, 115200n8
Upgrading from ar71xx target:
- Put image into board:
scp openwrt-ath79-generic-8dev_carambola2-squashfs-sysupgrade.bin \
root@192.168.1.1/tmp/
- Run sysupgrade
sysupgrade /tmp/sysupgrade.bin
Upgrading from u-boot:
- Set up tftp server with sysupgrade.bin image
- Go to u-boot (reboot and press ESC when prompted)
- Set TFTP server IP
setenv serverip 192.168.1.254
- Set device ip from same subnet
setenv ipaddr 192.168.1.1
- Copy new firmware to board
tftpboot 0x81000000 sysupgrade.bin
- erase flash
erase 0x9f050000 +${filesize}
- flash firmware
cp.b 0x81000000 0x9f050000 ${filesize}
- Reset board
reset
Signed-off-by: Rytis Zigmantavičius <rytis.z@8devices.com>
[wrapped long line in commit description, whitespace and art address
fix in DTS, keep default lan/wan setup, removed -n in sysupgrade]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
ZBT-WD323 is a dual-LTE router based on AR9344. The detailed
specifications are:
* AR9344 560MHz/450MHz/225MHz (CPU/DDR/AHN).
* 128 MB RAM
* 16MB of flash(SPI-NOR, 22MHz)
* 1x 2.4GHz wifi (Atheros AR9340)
* 3x 10/100Mbos Ethernet (AR8229)
* 1x USB2.0 port
* 2x miniPCIe-slots (USB2.0 only)
* 2x SIM slots (standard size)
* 4x LEDs (1 gpio controlled)
* 1x reset button
* 1x 10 pin terminal block (RS232, RS485, 4x GPIO)
* 2x CP210x UART bridge controllers (used for RS232 and RS485)
* 1x 2 pin 5mm industrial interface (input voltage 12V~36V)
* 1x DC jack
* 1x RTC (PCF8563)
Tested:
- Ethernet switch
- Wifi
- USB port
- MiniPCIe-slots (+ SIM slots)
- Sysupgrade
- Reset button
- RS232
Intallation and recovery:
The board ships with OpenWRT, but sysupgrade does not work as a
different firmware format than what is expected is generated. The
easiest way to install (and recover) the router, is to use the
web-interface provided by the bootloader (Breed).
While the interface is in Chinese, it is easy to use. First, in order to
access the interface, you need to hold down the reset button for around
five seconds. Then, go to 192.168.1.1 in your browser. Click on the
second item in the list on the left to access the recovery page. The
second item on the next page is where you select the firmware. Select
the menu item containing "Atheros SDK" and "16MB" in the dropdown close
to the buttom, and click on the button at the bottom to start
installation/recovery.
Notes:
* RS232 is available on /dev/ttyUSB0 and RS485 on /dev/ttyUSB1
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[removed unused poll-interval from gpio-keys, i2c-gpio 4.19 compat]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
also fix the following problems in this commit:
glinet,gl-ar150: This router uses an uncommon order of setting up gmacs
in ar71xx. gmac0 is preferred to be wan port because of
the additional link status info available. So this
router will have eth0/eth1 swapped comparing to ar71xx.
tplink,tl-wr710n-v1: same as gl-ar150
embeddedwireless,dorin: eth0 is used as switch port, which was incorrect.
It's correct now, so keep this one untouched.
tplink,tl-wr842n-v1: we don't swap PHYs on ar7241 so the original port order
is incorrect.
reorder archer-a7-v5 entry.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
With a proper probe deferring for ag71xx we don't need to explicitly
probe mdio1 before gmac0.
Drop all "simple-mfd" in SoC dtsi so that gmac orders can be the same
as ar71xx.
This makes eth0/eth1 order the same as those in ar71xx, which means
we don't need a migration script for this anymore and we can merge
incorrectly split gmac/mdio driver back together.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
gmac0 may need a phy on builtin switch, which can be unavailable
if gmac0 is probed before builtin switch.
Return -EPROBE_DEFER in this case so that gmac0 can be probed
later.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The original one has the following problem:
1. Port mask of lan led includes wan port.
2. By using netdev trigger with vlan port, the link led
is always on.
This commits fixes the above problems by correcting port
mask for lan led and use swconfig trigger for wan leds.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Support for D-Link DWR-118 A1 was added before LEDs feature
in mt76x0e driver.
This fixes the 5GHz WiFi LED which was previously inverted.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Remove references to broken and mostly deprecated phy_ethtool_ioctl, use
new {s,g}et_link_ksettings and add nway_reset which was previously
handled in phy_ethtool_ioctl.
Cc: John Crispin <john@phrozen.org>
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=1982
Signed-off-by: Petr Štetiar <ynezz@true.cz>
ethtool doesn't work currently as phy_ethtool_ioctl expects user space
pointer, but it's being passed kernel one. Fixing it doesn't make sense
as {s,g}et_settings were deprecated anyway. So let's rather remove
phy_ethtool_ioctl and use new {s,g}et_link_ksettings instead. While at
it, update nway_reset as well.
Cc: John Crispin <john@phrozen.org>
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=1982
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This ioctl is currently routed through generic interface code:
dev_ioctl
dev_ethtool
__ethtool_get_link_ksettings
phy_ethtool_ioctl
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This ioctl is currently routed through generic interface code:
dev_ioctl
dev_ethtool
__ethtool_get_link_ksettings
phy_ethtool_ioctl
Cc: John Crispin <john@phrozen.org>
Cc: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This ioctl is currently routed through generic interface code.
dev_ioctl
dev_ethtool
__ethtool_get_link_ksettings
phy_ethtool_ioctl
Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Remove 701-phy_extension.patch from 4.14 and 4.19 kernel, as it's
currenlty broken and fixing doesn't make sense as most of it is
deprecated anyway.
Cc: John Crispin <john@phrozen.org>
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=1982
Signed-off-by: Petr Štetiar <ynezz@true.cz>
