Hardware specification:
- SoC: MediaTek MT7621AT (880 MHz)
- Flash: 16 MB (Macronix MX25L12835FM2I-10G)
- RAM: 128 MB (Nanya NT5CC64M16GP-DI)
- WLAN 2.4 GHz: 2x2 MediaTek MT7603EN
- WLAN 5 GHz: 2x2 MediaTek MT7615N
- Ethernet: 1x 10/100/1000 Mbps
- LED: Power, Wifi, WPS
- Button: Reset, WPS
- UART: 1:VCC, 2:GND, 3:TX, 4:RX (from LAN port)
Serial console @ 57600,8n1
Flash instructions:
Connect to serial console and start up the device. As the bootloader got
locked you need to type in a password to unlock U-Boot access.
When you see the following output on the console:
relocate_code Pointer at: 87f1c000
type in the super secure password:
1234567890
Then select TFTP boot from RAM by selecting option 1 in the boot menu.
As Linksys decided to leave out a basic TFTP configuration you need to
set server- & client ip as well as the image filename the device will
search for. You need to use the initramfs openwrt image for the TFTP
boot process.
Once openwrt has booted up, upload the sysupgrade image via scp and run
sysupgrade as normal.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Kmod-mhi-pci-generic supports Qualcomm modems over PCIe bus. On targets
without PCI support, this package is empty. Symbol CONFIG_MHI_BUS_PCI_GENERIC
depends on CONFIG_PCI.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Kmod-serial-8250-exar supports Serial cards connected via PCIe bus. On targets
without PCI support, this package is empty.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Kmod-i2c-designware-pci supports Synopsys I2C over PCIe bus. On targets
without PCI support, this package is empty. Symbol CONFIG_I2C_DESIGNWARE_PCI
depends on CONFIG_PCI.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Noteworthy changes in this release:
* New option --ignore-dirnlink
Valid in copy-out mode, it instructs cpio to ignore the actual number
of links reported for each directory member and always store 2
instead.
* Changes in --reproducible option
The --reproducible option implies --ignore-dirlink. In other words,
it is equivalent to --ignore-devno --ignore-dirnlink --renumber-inodes.
* Use GNU ls algorithm for deciding timestamp format in -tv mode
* Bugfixes
** Fix cpio header verification.
** Fix handling of device numbers on copy out.
** Fix calculation of CRC in copy-out mode.
** Rewrite the fix for CVE-2015-1197.
** Fix combination of --create --append --directory.
** Fix appending to archives bigger than 2G.
Removed upstreamed:
- 001-duplicate-program-name.patch
- 010-clang.patch
Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
The previously stated speed of sdr-104 in is too high for the hardware
to reliably communicate with some fast SD cards.
Rockchip boards have a common bug when operating uhs speed, which will
hang the system during a soft reboot.
To be on the safe side, lower the speed to workaround.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware
--------
RockChip RK3328 ARM64 (4 cores)
4GB DDR4 RAM
1x 1000 Base-T
2 LEDs (POWER / USER)
HDMI 2.0
3.5mm TRRS AV jack
Micro-SD slot
eMMC slot
1x USB 3.0 Port
2x USB 2.0 Port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card using
dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Add support for the Firefly ROC-RK3328-CC.
Manually generated of-platdata files to avoid swig dependency.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Some packages which are using local gnulib source
are expecting files to exist in the directory:
staging_dir/host/share/gnulib/doc
so delete the other doc directories directly
instead of excluding all of them.
Fixes: d167adbc4 ("gettext-full: bootstrap to local gnulib source")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
The filesystem is currently created on every build to trick the boot
loader of some FRITZ! devices into accepting the image. Sadly the
resulting squashfs-lzma filesystem is not reproducible. To fix this,
create a squashfs filesystem once and include it into the repository.
Creation happend as shown below
rm -rf empty_dir
mkdir empty_dir
./staging_dir/host/bin/mksquashfs-lzma \
empty_dir/ empty-squashfs-lzma \
-noappend -root-owned -be -nopad -b 65536 -fixed-time 0
Signed-off-by: Paul Spooren <mail@aparcar.org>
All callers of the rtl83xx_mc_group_* functions already do the same
check, so these aren't needed.
For rtl83xx_mc_group_alloc, this branch also incorrectly returned 0
instead of a negative value. If the branch wasn't effectively dead code
anyway, this could potentially have caused bugs, as 0 is a valid
multicast group entry index.
Fixes: cde31976e3 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The current implementation only works when store and load are called for
the same port without any other calls in between. This is because the
store function only saves a single port number instead of a portmask for
each group. It also doesn't take into account that the allocation of
multicast group entries might change between store/load calls.
As a result, the multicast port mask table gets corrupted. This also
includes the reserved entry for unknown multicast, which gets corrupted
even when no other mdb entries have been added.
Remove the code for storing/loading multicast groups entirely, as the
original commit message doesn't offer a convincing reason why this would
be necessary in the first place.
Fixes: 724e4af530 ("realtek: Store and Restore MC memberships for port enable/disable")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
There shouldn't be any reason to forward all multicast to the CPU. The
original commit message also doesn't provide a reason for this seemingly
unrelated change.
The current implementation of the delete method is also broken, as it
entirely removes any entry when the portmask contains only the CPU port,
even if it was explicitly created.
Fixes: 724e4af530 ("realtek: Store and Restore MC memberships for port enable/disable")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
There doesn't appear to be a reason to do this, as only the last entry
is actually reserved for unknown multicast.
This also fixes two issues:
- As the increment happened after the bounds check, the value of the
actually reserved last entry could be overwritten.
- On deletion of entries, a corresponding decrement was missing,
causing the wrong entry to be marked as free.
Fixes: cde31976e3 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Actually use the index returned by rtl83xx_find_l2_cam_entry.
Fixes: cde31976e3 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The port_vlan_add method may be called while a port is already a member
of that VLAN, so it needs to be able to handle changed flags. Fix it to
properly handle when the PVID or UNTAGGED flag was previously set, but
now no longer is.
To reduce duplication, move PVID configuration to a separate function.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The registers L2_PORT_STATIC_MV_ACT seem to specify the action to take
when the source address of a packet exists as a static fdb entry on
another port. By default the configured action is to drop such packets.
For standalone ports, this behaviour is undesired, as all traffic should
be forwarded to the CPU. So change the action to forward on standalone
ports.
A situation where this issue can occur is when a non-offloaded bond
interface is part of a bridge. In that case, the CPU port will have fdb
entries for devices connected to the bond interface, which are managed
by the assisted learning feature.
For now, this is only implemented for RTL838x/RTL839x, as the available
set of registers differs for the other devices.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
All ports are disabled by default, so configure the port isolation masks
and the pm field accordingly in the setup function. When port_enable is
called for a port, the isolation masks will be set up so that traffic
can flow between the port and the CPU.
While at it, change the code to also use the traffic_set method in
rtl83xx_setup, instead of writing to the RTL838x_PORT_ISO_CTRL(i)
registers directly.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Correctly update the isolation mask of the port being configured. The
port_bitmap variable should contain all other bridge members and needs
to be actually removed from the isolation mask instead of added to it.
Also actually remove the port being configured from the pm field of the
other ports, so that any other ports that are currently disabled will be
configured correctly when they are enabled.
Fixes: df8e6be59a ("rtl838x: add new architecture")
[fixed updating pm field of other ports]
Fixes: 2b88563ee5 ("realtek: update the tree to the latest refactored version")
[reintroduced incorrect pm field update]
Fixes: 27029277f9 ("realtek: add switch driver support for the RTL93XX based switches")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Add support for NXP LS1028ARDB reference board. It's a dual core
Coretex-A53 board with 4G RAM and 5 Eternet ports (4 ports are
connected to MSCC Felix switch).
The original layout of NXP board has been kept but firmware
images are adapted to be more sysupgrade friendly. At the moment
NOR and SD boots are supported.
NOR flash instructions:
* make sd card with sdboot image
* boot
* write firmware image to spi flash
$ mtd write /tmp/openwrt-layerscape-armv8_64b-fsl_ls1028a-rdb-
squashfs-firmware.bin /dev/mtd0
* change jumper to NOR boot and reset
V3:
* Added board specific network defaults for lan/wan
v2:
* Added INA220 curent monitor, PCF2129 RTC clock and NXP
SA56004ED temperature sensor to default packages
* removed compat fixups for thist board
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
Support uboot for NXP LS1028ARDB reference board. GIC V3 has to
be disabled in the uboot config to allow booting upstream kernels.
This patch can be dropped once uboot is updated to 2022.04 version
to nxp-qoriq github lf-6.1.1 branch.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
There seems to be a difference in firmware calling convention
between upstream and NXP kernels. On some cpus like ls1028
it will hang on firmware secure get random when using LF uboot
with upstream kernel. Instead of commenting it out, don't call
get radnom seed when "kaslr-seed" is not present in device tree.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
To support the widest variety of modems, allow restoring previous
behaviour of configuring the link throug means of DHCP(v6) exclusively.
Change the default value of "dhcp" and "dhcpv6" UCI options to "auto",
while keeping the default behaviour of "prefer out-of-band configuration",
intact. Setting "dhcp" or "dhcpv6" to boolean 1 will now force using
DHCP and DHCPv6, respectively.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
The ZTE MF282 is a LTE router used (exclusively?) by the network operator
"3".
Specifications
==============
SoC: QCA9563 (775MHz)
RAM: 128MiB
Flash: 8MiB SPI-NOR + 128MiB SPI-NAND
LAN: 1x GBit LAN
LTE: ZTE MF270 (Cat4), detected as P685M
WiFi: QCA9880ac + QCA9560bgn
MAC addresses
=============
LAN: from config
WiFi 1: from config
WiFi 2: +1
Installation
============
TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:
setenv serverip 192.168.1.100
setenv ipaddr 192.168.1.1
tftpboot 0x82000000 openwrt.bin
bootm 0x82000000
From this intiramfs boot you can take a backup of the currently installed
partitions as no vendor firmware is available for download.
Once booted, transfer the sysupgrade image and run sysupgrade.
LTE Modem
=========
The LTE modem is probably the same as in the MF283+, all instructions
apply.
Configuring the connection using modemmanager works properly, the modem
provides three serial ports and a QMI CDC ethernet interface.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Synchronize the ath11k backports with the current ath-next tree.
This replaces the 160MHz with the upstreamed one, fixes 6GHz only WIPHY
registration, allows SAR usage on WCN6750 and plenty of REO fixes.
Signed-off-by: Robert Marko <robimarko@gmail.com>
While improving access path analysis a typo happened. Now it can happen
that gcc misscompiles. The patch is fixing the issue. However, also
other gcc versions 10.2+ are affected. They also should be bumped or the
fix should be backported.
For more bug information have a look at:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=109585
Signed-off-by: Nick Hainke <vincent@systemli.org>
Rename to Fritz!Box to keep naming uniform.
Fixes: ceac4ae3b4 ("lantiq: xway: add support for AVM FRITZ!Box 7330")
Signed-off-by: Nick Hainke <vincent@systemli.org>
Changes:
43f81b4 wireless-regdb: update regulatory database based on preceding changes
66f245d wireless-regdb: Update regulatory rules for Hong Kong (HK)
e78c450 wireless-regdb: update regulatory rules for India (IN)
1647bb6 wireless-regdb: Update regulatory rules for Russia (RU). Remove DFS requirement.
c076f21 Update regulatory info for Russia (RU) on 6GHz
Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
Using the local gnulib source during autogen.sh
allows for fine-grained control over the macros
and source files for use with gettext
but part of gnulib instead of gettext,
without having to wait for a release
or deal with gnulib as a git submodule.
This is an alternative to running autoreconf.
It also removes the need to patch macros
in the case where there is a conflict
between the source and our aclocal directory.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Using the local gnulib source during bootstrap
allows for fine-grained control over the macros
and source files for use with coreutils
but part of gnulib instead of coreutils,
without having to wait for a release
or deal with gnulib as a git submodule.
In this case, the execution of autotools
must be skipped by force.
Autoconf and Automake during bootstrap on coreutils
only works right when using directly checked-out source.
There is a symbol in gnulib, @GNULIB_TIME@
that is not yet defined in coreutils source,
so we use the backup of lib/time.in.h instead
of the one provided by gnulib source.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
