r45954 ("ar71xx: fix 100/10mbps ethernet link issues on mynet range
extender") introduced a pdata based modification of the tx_clk_dly. But it
was not checked if pdata actually existed. This caused a page fault on all
devices which didn't have at803x_platform_data specified for an at803x
based device.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46200
Update firmware name and md5sum. MAC-address location remains
unchanged from previous version.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46196
- it should be BOARDNAME instead of BOARD_NAME
- kernel partition should be padded to 1536k (somehow this padding was lost in translation to BuildCode in bc797c73f6328941b2194d144385655ad9297e7c)
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 46193
EPG5000 uses ath79 nvram functions, but does not select it. This breaks
build if no other board support enabling nvram support is selected.
Closes#19952.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46190
r46161 updated headers also touched by it, so it needed to be refreshed
as well.
Closes#20033.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46165
TP-Link ships wr740n v5.0 to Romania (so probably everywhere except
China) with 4 MB flash and 32 MB memory (confirmed by their local
support). This patch adds support for the v5.0 clone of v4, i just
tested it on my own v5.0 router and it works.
Signed-off-by: Daniel Petre <daniel.petre@posteo.net>
SVN-Revision: 46115
The hardware should be almost the same as TL-WR720N-v3. WiFi and LAN networks
were tested by "Lo Yuk Fai <loyukfai@gmail.com>". Failsafe and slider switch
were tested by "Wong min <alpha080@gmail.com>".
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 46046
This patch adds support for the Bitmain Antminer S1 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: James Hilliard <james.hilliard1@gmail.com>
SVN-Revision: 46044
Some devices ship with NAND images that use BCH ECC. Let the driver know
about that ECC mode so that it can be selected by machine files.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
SVN-Revision: 46022
It seems that there are maximum timings for mdio accesses that can be
hit when the system is under load and the thread is scheduled during
a read or write access. Since there is no way of knowing if this
happens as there is not even a parity bit, try to work around it
by disabling interrupts during any gpio-mdio accesses.
Performance impact seems to be neglectable, as mdio accesses are not
that often.
Hopefully fixes#19500.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46012
AR8337 supports a configuration bit to swap MAC0 and MAC6.
Currently this is set in general if an AR8337 is detected and causes
issues with devices using an AR8334 (internally an AR8337, just
less chip pins).
And it might even cause issues with AR8337-based devices with
different board designs.
Swapping the MAC's however isn't needed for AR8337 in general.
It's just needed in case of certain board designs (affected devices
seem to be based on Atheros reference board AP135/136-010).
Therefore this configuration bit should be moved to platform data.
The patch includes the needed changes to the device initialization
code of affected devices. Hopefully I didn't miss any ..
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 45970
This patch adds the pll_1000 value for eth0 interface. This makes the Rocket M
XW image compatible with other Ubiquiti devices with similar hardware with a
Gigabit Ethernet port.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 45965
In new firmware-4.bin (for ath10k) mac offset is 0x114 (276), not 0x118 (280).
This also closes#19751, bug introduced in #45624
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 45958
The mynet range extender hardware is suffering from ethernet
link loss when booting with a recent openwrt image. This only
happens on 100mbps links, with 1Gbps speed the link was fine.
The cause of the problem is that the AR8035 PHY (aka F1E)
requires turning on and off the special TX delay setting
depending on the speed of the link.
The 10mbps mode only needed the proper pll value, which was
extracted from the vendor code.
Reported-by: Pascal Paradis
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 45954
They are useless, as the platform already selects the right options for
NAND support. The main reason for removing them is the fact that it
makes kernel configs more annoying to maintain on platforms that provide
NAND drivers but disable them (e.g. ramips)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45919
The v1 identifies as v10 internally. As there is no TL-WA830RE v10, add a
workaround to avoid confusing users.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 45903
Building the loader in Image/Build/TPLINK-SAFELOADER would break the image
builder as no target compiler is available in that stage.
Fixes#19580
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 45855
In contrast to Image/BuildLoader, Image/BuildLoaderPatched first patches the
kernel command line in the image and then builds the loader without command
line. This allows building loaders for systems which don't boot correctly when
the kernel command line is provided by the loader (like the TP-LINK CPE series).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 45854
This is the case e.g. if JFFS2 partition is full.
see: https://www.mail-archive.com/linux-unionfs@vger.kernel.org/msg00246.html
(a small error in a logmessage was changed and reported upstream)
runtime tested on ar71xx with kernel 3.18.11 and r45772
this paritially fixes#19564
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
Acked-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 45833
This patch is to add support for the Meraki MR12 and MR16 Access Points.
Currently everything is working, minus the 2nd NIC interface on the MR12
which is built into the SoC.
Signed-off-by: Chris R Blake <chrisrblake93 at gmail.com>
SVN-Revision: 45726
There are 2 images missing: TLWR2543 TLWR1043V2 which have special properties.
v2: set correct DEVICE_PROFILES for all images.
v2: migrate TP-LINK TL-WR710N v2 which was committed after v1.
v2: split very very long line `TARGET_DEVICES +=` into smaller parts
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 45643
Users will now be provided with the inherent wifi toggle functionality
of /etc/rc.button/rfkill
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45635
Originally pressing a button would trigger a release state and vice-versa,
as observed from hotplug.d.
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45634
Most people report broken ethernet with upstream. Last year, user "franz.flasch"
authored a working mach-file. His patch is outdated so I modernized it. Original
patch and user commentary on page 1:
https://forum.openwrt.org/viewtopic.php?pid=260861#p260861
I have figured out what the critical differences are between the two that caused
upstream ethernet to break.
1) Both ath79_init_mac() functions calls must be invocated before any GMAC init
2) must init GMAC0 before GMAC1
That was enough to get upstream to function, but I wanted to enjoy my confidence
having tested franz's patch for a week sucessfully, so I put his whole
function in, which only features more differences in order of function calls.
An expert should consider these changes, which could pose potential bugs/issues:
1) No longer using the flag AR934X_ETH_CFG_SW_PHY_SWAP in the
ath79_setup_ar934x_eth_cfg() call.
2) Possible consequence of no longer explicitly setting ethernet duplex/speed.
Review: With this patch, my ethernet and wireless works.
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45633
It is common that the router provider be used rather than product name.
One can see this in target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45630
This patch adds support for the XW version of the Rocket M series devices
manufactured by Ubiquiti, based on the Atheros AR9342 SoC.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 45553
It was reported that OM5P-AN needs not only a delay setting of 1 for RXD/RDV
but 2. These was found when testing with a NetGear GS752TP POE switch with a
cable length of 50ft and 250ft.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 45524
The ETH_RXDV_DELAY (17:16) and ETH_RXD_DELAY (15:14) are currently not cleared
by the function ath79_setup_ar934x_eth_cfg. Clearing these in the
ath79_setup_ar934x_eth_cfg may cause problems on some hardware because they
rely on the preset value by the bootloader.
Instead another function is introduced which also works on ETH_CFG on AR934x.
It can be used to safely clear and set ETH_RXDV_DELAY and ETH_RXD_DELAY on
machines which require special settings.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 45523
The commit r38948 ("ag71xx: add F1E specific feature bit definitions to AR934X
register file") introduced definitions for some bits in the RDV/RXD part of the
ETH_CFG register of AR934x. These are incomplete because ETH_RXDV_DELAY is
specified as 17:16 and ETH_RXD_DELAY is specified 15:14. The original commit
only specified the lower bits. The upper bits also have to be unset when the
lower bits should only be set.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 45522
The tx/rx delay bits in the ETH_XMII_CONTROL register have to be unset when the
enable_rgmii_rx_delay/enable_rgmii_tx_delay will be set in the AT803x PHY.
Othwise the throughput in gigabit mode is heavily reduced.
Signed-off-by: Sven Eckelmann <sven@open-mesh.org>
SVN-Revision: 45521
Profile definitions need to be checked and fixed before this patch can
be applied again.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45511
The new building code included the rootfs twice when building tplink initramfs images.
To make it more readable move initramfs into an own build step
Build/mktplinkfw-initramfs.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 45491
The new image size is verified by a running tplink device and checked
against mktplinkfw source code.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 45488
Open-Mesh OM5P-AN use a AT8035 (F1E) behind one of the ethernet ports. This PHY
requires special flags to work correctly. Otherwise massive packet loss happens
with active POE or when switching the link speed from gigabit ethernet to fast
ethernet. The generic PHY doesn't have support to change these settings.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 45439
The OM5P-AN boards are suffering from ethernet packet loss when booting with
some active POE setups or when switching to Fast Ethernet when previously
booted with Gigabit ethernet attached.
The cause of the problem is that the AR8035 PHYs requires special register
settings to work reliably on these boards. Enable the RGMII TX, RX delays and
disable SmartEE functionality of the AR8035 PHYs. Also enable the RXD and RDV
delay in the ETH_CFG register to fix the issue.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 45438
None of the LEDs are enabled by default on the Hornet-UB X2 board
(the 16/64MB version of the Hornet-UB), because it uses a different
board-name ("hornet-ub-x2"); but hornet-ub and hornet-ub-x2 boards
are equivalent WRT their LEDs.
SIgned-off-by: Joshua Judson Rosen <jrosen@harvestai.com>
SVN-Revision: 45328
On newer Mikrotik boards, the radio calibration data
is stored differently and uses LZO compression instead
of RLE.
Update the RouterBOOT helper code to support the new
format.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 45297
Platform device support has been removed from the gpio-74x164
driver in 3.14. Restore that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 45203
The setting has been lost during the transition to 3.18.
The CONFIG_M25PXX_PREFER_SMALL_SECTOR_ERASE option is not
available anymore, so use CONFIG_MTD_SPI_NOR_USE_4K_SECTORS
instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 45161
There were a few issues with the existing code to detect the model string:
* Always using the string starting with byte 56 would cut off the W of WNDR when
the ID starts with 29763654+16+64 instead of 29763654+16+128
* The string contained garbage after the zero byte instead of cutting it off
after the zero (which wasn't always visible using busybox tools, but could
confuse other scripts)
Tested on a WNDR3700v1 and a WNDR3700v2 using the new 29763654+16+64 ID in the
ART. Furthermore, tested against ART dumps of a WNDR3700v2 using the old
$'\xff...' value and a WNDR3800.
The [ -z "$model" ] check was dropped as there is no way to actually hit this
unless no ART partition is found at all.
The awk command was carefully crafted to work both with gawk and the (horribly
broken) busybox awk.
Fixes#18992.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 45140
There are two versions of the GL.iNet, the 6408A and the 6416A. The only
difference is the flash size.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44860
While the switch positions aren't explicitly labeled as on and off, we've heard
complaints about them being wrong. This patch changes the handling to match the
stock firmware.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44795
My previous patch regarding the Hornet-UB board
(commit: beed4d82d6a0154b0cd5f7b84e2180215ace6718) actually
causes the WPS led state to be inverted. Practically this meant
that value 0 in /sys/class/led/alfa:blue:wps/brightness would
turn the LED on and any positive value (1-255) would turn it off.
The above of course is confusing and hence reverting this value
back to the way it was before beed4d82d6a0154b0cd5f7b84e2180215ace6718.
Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>
SVN-Revision: 44791
This problem has existed at least since Attitude Adjustment and
is also present in trunk. Basically on the Hornet-UB board the
functionality of RESET and WPS have "switched places".
There are two tickets about the issue at dev.openwrt.org,
The solution suggested on them both is incomplete though
and introduces the following proglem:
Patching as suggested on #14136/#15282 will result in a situation
where simply pressing the RESET button on the bottom will cause
FACTORY RESET to be run. This is due to GPIO high/low state being
incorrect as a result of the above change and virtually the RESET
button is in the pressed-down state the entire time. When it is
then physically pressed, that causes the opposite, release, to be
triggered and since to the board it seemed that the button was
pressed long before it was released, the FACTORY RESET results.
The attached patch works as expected. I have verified both the
incorrect functionality as well as after fixing the issue as
described in the patch and flashing the resulting firmware to a
Hornet-UB board.
Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>
SVN-Revision: 44692
Previously, the generated images for the My Net Wi-fi Range Extender
wouldn't always work (and panic) due to the fixed mtd offsets and
sizes for the kernel and rootfs. This patch fixes the problem by
utilizing the shared Cybertan's partition parser to recalculate
the mtd partitions for every image dynamically everytime.
Reported-by: Pascal Paradis <peparadis@yahoo.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44665
By removing the NL16 signature check, the parser can be
utilized by other devices like the WD My Net Wi-fi Range
Extender.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44664
This patch renames the partition parser from
wrt160nl to more generic cybertan.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44663
405-mtd-tp-link-partition-parser.patch was updating the
WRT160NL's partition parser Kconfig. This patch moves the
relevant change into the right file:
404-mtd-wrt160nl-trx-parser.patch
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44662
Please also backport to Barrier Breaker (this same patch applies there too).
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 44647
OpenWrt can be flashed with following uboot commands:
tftpboot 0x80500000 openwrt-ar71xx-generic-wpj558-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 44620
CONFIG_GENERIC_NET_UTILS is selected by CONFIG_NET and already enabled
in generic config, so we don't need this symbol in platform specific
configurations.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44611
Most MIPS targets have it disabled, so move the symbol to the generic
configs to keep target configs small.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44583
The firware md5sum check never worked due to missing dollar signs.
Also suppress
`md5sum: can't open '/lib/firmware/ath10k/QCA988X/hw2.0/firmware-3.bin'`
error on any board not using ath10k.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44486
This patch adds corrected profile and build image for the TL-MR12U board.
Unfortunately i cannot test the factory image since i can't find anywhere
the original chinese firmware but
the generated openwrt-ar71xx-generic-tl-mr12u-v1-squashfs-sysupgrade.bin
worked just fine over a modified mr3040 factory image i managed to modify
to initially flash the mr12u from the original firmware.
Proper kernel support probably should be added since cat /proc/cpuinfo shows
MR13U.
Signed-off-by: Daniel Petre <daniel.petre@gmail.com>
SVN-Revision: 44427
This patch adds user-space support for the TL-MR12U board based on the mr13u patches.
Signed-off-by: Daniel Petre <daniel.petre@gmail.com>
SVN-Revision: 44426
This patch adds the mc-mac1200r target to do_load_ath10k_board_bin() in
target/linux/ar71xx/base-files/lib/preinit/81_load_ath10k_board_bin to load the
ath10k radio MAC address from the EEPROM in MERCURY MAC1200R devices
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44375
This patch adds support for MERCURY MAC1200R, a dual band 802.11bgn + 802.11ac
router based on the AR9344, with QCA988x ath10k radio and 5 Fast Ethernet ports
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44359
This device is very similar to the TL-WR841N v8, only two LED GPIOs are
different.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44255
The board is already supported by OpenWrt. WNR1000v2/WNR1000v2-VC are
pretty much the same as WNR2000v3/WNR612v2, therefore the same
initialization code and flash layout is used.
Signed-off-by: Ștefan Rusu <saltwaterc@gmail.com>
Tested-by: Douglas Fraser <1dsfraser@gmail.com>
SVN-Revision: 44221
Fix the WLAN MAC address to match the one printed on the label by using the
correct address from the ART instead of the address of the LAN interface.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44183
This patch adds an entry in the uci-defaults' led-file to configure the
WAN and WLAN LEDs by default.
Signed-off-by: Vincent Wiemann <me@bibbl.com>
SVN-Revision: 44165
TP-LINK TL-WR843ND v1 is the same model like wr41, but with
Power over Ethernet on wan port.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 44085
the GPIO controlling the rf filter is not configured properly by this patch.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44077
This patch adds soc support for QCA9561 and TP9343.
TP9343 is a reduced version of QCA9561, which can be found in TP-LINK routers in China.
The qca956x_wmac has not yet been supported by ath9k.
tested on TL-WDR6500 and TL-WR882N v1 (Chinese version)
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 43744
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43715
It moves firmware patch code behind an extra check on board_name.
Otherwise it will calculate firmware checksum for unaffected boards.
It also reduce boottime by a md5 calculation and removes error message
on boot if firmware not found.
SVN-Revision: 43679
I don't see that we're in an atomic context so there's no need to
busy-wait. Therefore replace the delay with sleep calls.
See also Documentation/timers/timers-howto.txt. It states:
"In general, use of mdelay is discouraged and code should
be refactored to allow for the use of msleep."
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43539
Replace the fixed wait time of 1s with polling for BMCR_RESET
to be cleared on all PHYs.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43538
Patch to add the buildprofile for the GL-Init-6408A-v1 and the GL-Inet-6416A-v1
Both devices are identical, only difference is one comes with 8MB flash and
the other with 16MB flash
Official website: http://www.gl-inet.com/w/?page_id=241&lang=en
Comprehensive list of specs: https://revspace.nl/GL-Inet
Signed-off-by: Martijn Zilverschoon <martijn@friedzombie.com>
SVN-Revision: 43462
This adds support for the TP-LINK CPE210/220/510/520 (Pharos series). These
devices are very similar to the Ubiquiti NanoStations, but with better specs:
faster CPU, more RAM, 2x2 MIMO.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 43385
replace all occurences of LINUX_VERSION with the cleaner
approach. future kernel upgrades must mostly touch only
one file. the only platform left is netlogic, because it
uses a intermediate kernel 3.14.16
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 43047
This patch changes the code of the Wi-Fi On/Off button on the TP-Link WR1043ND v2
from KEY_WLAN to KEY_RFKILL (and renames a few constants to match). The reason
for this change is, that the KEY_WIFI button code is not recognized by the
hotplug subsystem. This means that the userspace is not notified about the
button being pressed which effectively renders it useless.
Signed-off-by: Josef Gajdusek <atx@atx.name>
SVN-Revision: 42922
Currently JFFS2 end-of-filesystem marker 0xdeadc0de is included the
computation of image's MD5 checksum as part of the seama header. But
OpenWrt will erase blocks including and after the marker thus
invalidating the checksum after the first boot.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 42915
Qihoo C301 has 2 flash chips of which one is used as primary and the
other is used as backup. OEM U-Boot will try to boot an activeregion N
with imageNstatus=0 and imageNtrynum <= imagemaxtry. If such a region
is found, bootloader will try to increment imageNtrynum and boot it.
This patch tries to reset imageNtrynum after each successful boot (if
the boot process reaches the execution of /etc/init.d/done).
root@OpenWrt:/# hexdump -C -n 128 /dev/mtdblock9
00000000 9e f3 63 91 61 63 74 69 76 65 72 65 67 69 6f 6e |..c.activeregion|
00000010 3d 31 00 69 6d 61 67 65 31 73 74 61 74 75 73 3d |=1.image1status=|
00000020 30 00 69 6d 61 67 65 32 73 74 61 74 75 73 3d 30 |0.image2status=0|
00000030 00 69 6d 61 67 65 32 74 72 79 6e 75 6d 3d 30 00 |.image2trynum=0.|
00000040 69 6d 61 67 65 6d 61 78 74 72 79 3d 33 00 69 6d |imagemaxtry=3.im|
00000050 61 67 65 31 74 72 79 6e 75 6d 3d 30 00 00 00 00 |age1trynum=0....|
00000060 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 42914
[base-files] shell-scripting: fix wrong usage of '==' operator
normally the '==' is used for invoking a regex parser and is a bashism.
all of the fixes just want to compare a string. the used busybox-ash
will silently "ignore" this mistake, but make it portable/clean at least.
this patch does not change the behavior/logic of the scripts.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42911
This patch fixes LED definitions for the DRAGINO2 board.
1. It renames the Router/USB led to System, as it is now marked "SYS" on the board.
2. It gives control of the LAN and WAN leds and some other GPIOs to Linux.
3. It fixes the active_low property for the LAN and WAN leds.
4. It sets up WLAN, LAN and WAN leds in the UCI defaults.
5. It allows usage of the System led by the diag.sh script, so it will be used to indicate boot and failsafe status.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 42897
All TP-LINK machine names begin with "TP-LINK", so there's no need to check for
more specific model names. This also allows adding new models like the Archer
series more easily.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 42795
A typo in the definition for the OM2P reset button disabled its functionality
in OpenWrt. The actual button for these two devices is "1" and not "11".
Signed-off-by: Oren Poleg <oren@poleg.org>
[sven@open-mesh.org: added a commit subject+message]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 42782
Qihoo 360 C301 is a dual band wireless router supports 802.11n and 802.11ac.
Its chipset is AR9344 + AR9882 with two 16MB flashes.
This patch adds its initial support.
v2:
* use mtd_get_mac_ascii to fetch MAC address for ath10k.
* use ath79_register_pci to initialize AR9882.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 42552
While the AR9331 has a gigabit MAC towards the internal switch, the
integrated PHYs however are only 100-base-tx capable. The existing code
however advertieses gigabit capability in the link status word. If you
attach such a PHY to a gigabit capable switch on the remote end, with
some probability it attempts to negotiate gigabit and fails, falling
baco to the AR9331 assuming a 10mbit half-duplex link. This has been
observed quite frequently with the Carambola2 and gigabit capable
switches.
In ath79_register_eth(), "pdata->has_gbit = 1;" is set unconditionally
for both AR9331 ethernet ports. This is most likely wrong. Despite the
two MAC IP cores being gigabit MACs, the MAC for eth1 is connected to a
100base-T PHY via MII. The has_gbit attribute is used in the ethernet
driver to determine the supported link modes.
So either pdata->has_gbit is not set to 1 anymore, or the ethernet
driver needs to be modified to determine the advertised link code word
on another criteria than pdata->has_gbit. This patch implements the
former solution.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
SVN-Revision: 42432
This improves performance when doing concurrent rx/tx on a single
ethernet MAC, e.g. when routing between VLANs.
Fixes#13072
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 42328
This sets the MAC address of the WLAN interface to the "official" primary MAC
address (the one on the label under the devices, and the one used with the stock
firmware). The MAC address used so far (primary-1) isn't even used at all with
the stock firmware, which sets (primary) on LAN and WLAN and (primary+1) on the
WAN interface (like OpenWrt does with this patch).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 42193
The OpenMesh MR600(v1) can only enable the 2.4G WiFi PHY LED through the
mini-PCIe device. Not configuring the LED pin inside the platform data
makes it impossible to configure it through any standard OpenWrt tool.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 42184
Apparently this is a fairly common refurb unit of the 3800 series now,
with merely the recognition string changed in the boot loader.
Signed-off-by: Dave Taht <dave.taht@bufferbloat.net>
SVN-Revision: 42023
Change list:
* Remove button info on GPIO12, there is no button there.
* Remove nvram mtd partition, as it's not used for anything, saves 64k for user data.
Tested building for carambola2 target.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
SVN-Revision: 41993
this caused factory resets when reboot was pressed
Signed-off-by: Brent Thomson <brentthomson@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41932
without this the build for NBG6716 fails due to missing packages
https://dev.openwrt.org/ticket/17325
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41930
The airGateway has a reset button connected to GPIO 12, so we should use it.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
SVN-Revision: 41794
The default case in 02_network is inappropriate for the MikroTik RouterBOARD 91x boards because they do not have a WAN port, so don't bother setting the non-existent eth1 interface as the WAN port.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
SVN-Revision: 41767
This patch adds support for the Ubiquiti Networks airGateway.
Based in part on code posted by David Hutchison <dhutchison@bluemesh.net> on openwrt-devel:
https://lists.openwrt.org/pipermail/openwrt-devel/2013-December/023035.html
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
SVN-Revision: 41766
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5838/
[juhosg:
- fix coding style,
- check the first and the last character of the MAC string
instead of using the strchr() function]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 41622
The GL-Connect GL.iNet v1 router is basically a TP-Link TL-WR703N with
more DRAM/Flash, 2x Ethernet ports and console/GPIO header in the same
small form-factor:
<http://www.gl-inet.com/w/?lang=en>
Moreover, the manufacturer is promoting the OpenWrt usage to replace
the original firmware and proposing patches against both AA and trunk:
<http://www.gl-inet.com/w/?p=398&lang=en>
This is a clean up of the original manufacturer GPLv2 patch by alzhao,
proposed to the list by Mark Janssen.
Signed-off-by: Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Mark Janssen <mark@sig-io.nl>
Signed-off-by: alzhao <alzhao@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5273/
[juhosg:
- remove user-space and image generation support, will be included
from other patches,
- fix coding style and drop superfluous comment in mach-gl-inet.c,
- rename and refresh kernel patch,
- adjust subject]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 41618
The RB2011UiAS is almost exactly the same as the RB2011UAS, which is
already supported. Hardware-wise, it adds a passive power injector on
Eth10. Software-wise, Routerboot passes a different board name on the
kernel command line. Hence the need for a patch.
Not yet working:
* touchscreen: doesn't work on RB2011UAS either. The touchscreen itself
seems to be driven by an ADS7843-compatible IC, but figuring out which
GPIO pins it's connected to is work for the future.
* control of power injector: remains off. Probably also GPIO-controlled.
Signed-off-by: Soren Harward <stharward@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5841/
[juhosg: rename and refresh the kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 41617
With help of this script the ath10k board.bin settings are loaded from
flash and saved to the ath10k firmware directory. The driver reads it
later in the boot process.
Signed-off-by: André Valentin <avalentin@marcant.net>
SVN-Revision: 41562
This patch adds support for the MikroTik RouterBOARD SXT Lite.
The new RB911L series is also supported as a result.
v2 of this patch fixes the wmac offset to match what is on the sticker.
v3 refreshes the patch against r41148 and defines the power led as the status led in diag.sh
v4 refreshes the patch against r41353 and fixes the patch path issue to make git am work correctly
v5 selects the kernel config option in the mikrotik profile rather than in the main ar71xx config
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41450
205-fix-headers_install.patch is obseleted by upstream commit 3246a0352e3d58380b9386570f1db1faf7edf8a8
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41351
This enables the procd nand upgrade for ZyXEL NBG 6716. Also the ubi config
is cleaned up to match the wndr4300.
Signed-off-by: André Valentin <avalentin@marcant.net>
SVN-Revision: 41346
WAN and LAN are swapped the wrong way around. This patch fixes that by adding the 951Ui-2HnD to ar71xx.sh and the relevant entry in 02_network.
This patch also defines the ACT LED as the status LED in diag.sh.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41255
I added WIFI LED support (so now AP blinks nicely), I removed WPS
button GPIO (as it doesn't exist) and changed GPIO for reset button.
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
SVN-Revision: 40976
This board manufactured by HiWiFi has the following features.
- Atheros 9331 SoC.
- 16MB flash and 64MB RAM.
- 4GB eMMC storage via SK6226 USB 2.0 controller.
- 2 LAN and 1 WAN ethernet ports with LEDs on them.
- 3 blue LEDs on the front panel.
- 1 button labeled as "reset".
- Powered by a USB cable.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 40973
The TL-WA730RE seems to be almost identical to TL-WA701ND, just
that it comes without PoE and a stock-firmware claiming the device
to be a "Range Extender".
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 40972
Detect TL-WA7510N v1 by the board name as defined in mach-tl-wa901nd.c
and add hardware ID to tplink_board_detect
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 40971
Dlink dir-615-e1 can use dir-600-a1's image, but the image can't be
uploaded through dlink's normal firmware update web page.
Add profile for dir-615-e1 so the generated image can be uploaded
through the firmware update web page.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
SVN-Revision: 40969
ARGC is a 'C-ism', but not known/valid in shell-syntax - insert the correct
var $# (=number of args) here. under normal conditions this had no impact,
but we should at least correct it. the error was observable like this:
root@box:~ [ -e "/etc/functions.sh" ] && . /etc/functions.sh
root@box:~ [ -e "/lib/functions.sh" ] && . /lib/functions.sh
root@box:~ . /lib/upgrade/platform.sh
root@box:~ . /lib/upgrade/common.sh
root@box:~ platform_check_image /tmp/myfirmware.bin
ash: bad number
root@box:~ echo $?
0
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 40915
The most important one is qca_force_host_mode, which also sets the
'Stream Disable' bit in the usbmode register.
Fixes usb stability issues on AR933x and AR7241/AR7242
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40841
The change is the same as ("kernel/generic: modify mtd related
patches"). Since these files are under files directory, not a files
directory of specific kernel version, better to also change them. So
it will avoid adding files to future specific files directory
(e.g. files-3.14) for this mtd related change.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
SVN-Revision: 40732
The RB91x boards are suffering from ethernet packet loss after a cold
boot. The cause of the problem is that the AR8035 PHYs requires special
register settings to work reliably on these boards.
Enable the RGMII TX, RX delays and disable SmartEE functionality of
the AR8035 PHYs. Also enable the RXD delay in the ETH_CFG register
to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40509
Add a patch for the at803x phy driver, in order to be able
to configure some register settings via platform data.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40507
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg: use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40500
With this patch OpenWRT supports the following on the ZyXEL NBG 6716:
-WiFi 2G (ath9k)
-WiFi 5G (ath10k)
-NAND flash
-2 Ethernet interfaces
-USB 2.0
-LEDs including switch
-reasonale defaults at first boot
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg:
- rename and refresh kernel patch,
- fix a few typos,
- change button key codes,
- use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40499
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40481
Apart from the wireless chip, the WNDR3700 v4 and the WNDR4300
is the same device. Indicate this in the kernel files.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40479
The 5V power of the USB is controlled by a GPIO pin of
the external WiFi chip. Setup the GPIO bitmasks in the
platform data of the WiFi chip to ensure that the 5V
power gets enabled by the ath9k driver.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40478
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40477
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40475
The bootloader does not initializes the output function
correctly for all LEDs. DO that from the board setup code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40474
The hardware manual says amber so change the color part of
the LED names to reflect that. Also update the constant names.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40473
Adds support for the received signal strength indicator LEDs of the
Bullet M, Nanostation M and Rocket M devices.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/5108/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40471
Move the comments out from the shell script to fix build
breakage introduced in r40464.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40466
The C7v2 has 16 MB flash and QCA9880-BR4A rev 2 supported by ath10k driver.
The C7v1 had 8 MB flash and the unsupported QCA9880-AR1A rev 1.
Signed-off-by: Adam Serbinski <adam@serbinski.com>
Patchwork: http://patchwork.openwrt.org/patch/5071/
[juhosg:
- remove the v2 specific profile add the ath10k driver to the existing
Archer C7 profile instead. Although on v1 devices it does not change
the non-working behaviour, but the ath10k driver is useful for users
whom have replaced the wifi card with a supported one in their units.
- update image/Makefile to build firmware image for both boards if the
Archer C7 profile is selected]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40463
Everything seems to be working fine. Potential issues:
* VLAN port IDs are reversed with regard to the numbers on the case.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 40400
