20bf958 session: use uloop_timeout_remaining64
d11ffe9 session: use blobmsg_get_u64 for RPC_DUMP_EXPIRES
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Support for libsanitizer on MIPS 32 and MIPSEL 32 was added with GCC 9.
MIPS 64 and ARC are still not supported.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This version has some improvements for musl.
This version works fine for me on MIPS 32 BE without MIPS16 even on musl.
The additional patch is needed to make valgrind use the correct syscall
numbers for new syscalls like clock_gettime64. The MIPS architecture
uses special syscall ranges which are different from most other systems.
The patch is pending upstream: https://bugs.kde.org/show_bug.cgi?id=444781
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The removed patch was already applied upstream.
gdb now mandatory depends on gmp, tell configure where to find it
explicitly. We already build gmp in the tools directory for gcc. Also
make it use mpfr and mpc as we also build both of them.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Disable some of the ipq40xx devices due to their kernel size limitations.
These devices fail to build with kernel 5.10 and full buildbot config.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[keep gl-b1300/gl-s1300 enabled, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There have been enough tests and new developments require the new
kernel, so let's update it.
There is a bunch of devices that do not build anymore due to
kernel size limitations. These are disabled in a subsequent commit.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This implements the mapping recommendations from RFC8325, with an
update from RFC8622. This ensures that DSCP marked packets are properly
sorted into WMM classes.
The map can be disabled by setting iw_qos_map_set to something invalid
like 'none'
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This adds some essential files required by new 'cortexa7' subtarget,
dedicated for Cortex-A7 based NXP i.MX series. For now, the kernel
config-default focuses only on the i.MX 6UL family, as the following
changeset will introduce support for i.MX 6ULL based device. Support
for more platforms (e.g. i.MX 7) might be enabled later, while adding
more devices.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Subtarget-specific files under 'uboot-envtools' package are supported
since 6f3a05ebb0 ("uboot-envtools: support uci-default config also per
subtargets").
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Modern NXP i.MX series includes several different families, based on
single- or multi-core Arm Cortex-A CPUs. To be able to support more
families within a single target, we split the 'imx' in arch-specific
subtargets, starting with 'cortexa9' for the Cortex-A9 based i.MX 6,
already supported by the original 'imx6' target.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This is first step in migrating to a generic i.MX target which in the
next steps will also get divided into arch-specific subtargets.
In the result, this will make it possible to support, within a single
target, also other modern NXP i.MX families, like the i.MX 7, i.MX 8
or recently introduced i.MX 9.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This is a minor extension of the commit 26ae69fd03 ("imx6: refresh
kernel config with 5.10 symbols"), with correct and full disable of
the Arm Cortex-A7 based i.MX 6UL and 6UL{L,Z} families support and
re-enable of the Cortex-A9 based i.MX 6L{S,X}.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
U-Boot for the Gateworks Ventana includes filename of the boot script in
the default/embedded environment (see 'include/configs/gw_ventana.h' in
the U-Boot sources).
This restores the old boot script filename ('6x_bootscript-ventana'),
making Ventana boards boot again.
Fixes: 8dba71dd33 ("imx6: image: drop BOOT_SCRIPT and fix DEVICE_NAME")
Reported-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Netgear R6100 is a dual-band Wi-Fi 5 (AC1200) router based on Qualcomm
Atheros (AR9344 + QCA9882) platform. Support for this device was first
introduced in 15f6f67d18 (ar71xx). FCC ID: PY312400225.
Specifications:
- Atheros AR9344 (560 MHz)
- 128 MB of RAM (DDR2)
- 128 MB of flash (parallel NAND)
- 2T2R 2.4 GHz Wi-Fi (AR9344)
- 2T2R 5 GHz Wi-Fi (QCA9882)
- 5x 10/100 Mbps Ethernet (AR9344)
- 4x internal antenna
- 1x USB 2.0 (GPIO-controlled power)
- 6x LED, 3x button (reset, Wi-Fi, WPS)
- UART (4-pin, 2.54 mm pitch) header on PCB
- 1x mechanical power switch
- DC jack for main power input (12 V)
WARNING: sysupgrade from older stable releases is not possible, fresh
installation (via vendor's GUI or TFTP based recovery) is required.
Reason for that is increased kernel partition size.
Installation:
Use the 'factory' image under vendor's GUI or via TFTP U-Boot recovery.
You can use the 'nmrpflash' tool at a boot time, before kernel is loaded
or start it manually by pressing the 'reset' button for ~20 seconds from
powering up the device (U-Boot will start TFTP server on 192.168.1.1,
use TFTP client to send the image).
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
CONFIG_COMPAT_32BIT_TIME is a new symbol and has to be set to avoid:
Provide system calls for 32-bit time_t (COMPAT_32BIT_TIME) [N/y/?] (NEW)
CONFIG_RELOCATABLE needs to be enabled to make kernel start booting.
That raises a question: do we really need CONFIG_EXPERT=y ?
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The boot arguments are copied into the device tree by the boot loader
and taken from the device tree by the kernel.
The code which takes the boot arguments from the different sources was
reworked with kernel 5.5.
We have to activate CONFIG_MIPS_CMDLINE_DTB_EXTEND to take the boot
arguments from the device tree.
This makes the system boot on the board again.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Make the patches apply on kernel 5.10 and refresh the patches and the
kernel configuration on top of kernel 5.10.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The pistachio U-Boot expects a default configuration with the name
config@1 in the FIT image. The default was changed in OpenWrt some
months ago.
This makes the board boot again.
Fixes: 9f714398e0 ("build: use config-1 instead of config@1 as default")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It relies on a custom ax_code_coverage.m4 file included with strace.
Unfortunately, this conflicts with the one included with
autoconf-macros. Instead of creating a huge patch to fix it, just remove
the variable as code coverage is not used here.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
I had quite a hard time to understand what the change to net/core/dev.c
is supposed to do.
Simplify the change by returning NETDEV_TX_OK in case a eth_mangle_tx
callback was set but returned NULL instead of setting the return value
in the else branch.
Signed-off-by: Mathias Kresin <dev@kresin.me>
ar8216 switches have a hardware bug, which renders normal 802.1q support
unusable. Packet mangling is required to fix up the vlan for incoming
packets.
The patch was ommited at the time kernel 5.10 support was added but is
still required for ar8216 switches.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add the latest default Kernel for testing. This step is required to keep
UML in tree for the next release.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The UML target been outdated for a long time. Instead of just carrying
unmaintained code we should build it again and allow people and CIs to
use it for testing.
This commit removes the `source-only` feature which disables building.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This step drops support host build systems other than x86/64 to allow
two Kernel configuration in parallel. With this commit the setup follow
the config style of all other targets.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The current `uml` README is terribly outdated and non of the examples
work by default. Fix that and while at it convert it to Markdown.
Signed-off-by: Paul Spooren <mail@aparcar.org>
