There are a few targets that mess with the atm kernel headers. To avoid
incompatibility between kernel and user space during compilation, the
correct headers should be used.
Consequently, the package must also be marked as nonshared.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Extreme Networks AP3935i/e -
https://www.extremenetworks.com/support/documentation/access-points-ap3935i-e/
SoC: IPQ8068 QYY AT46279K45060I
RAM: NANYA 1527 NT5CC256M16DP-DI 515073W0EF 7 TW
FLASH: NOR - S25FL256S1 - 32MB
NAND - Macronix MX30UF4G28AB - 512MB
LAN: Atheros AR8035-A J5150WL 1515 CN - RGMII
LAN2: Atheros AR8033-AL1A SKCSR.AJ1 1444 China - SGMII
WLAN2: QCA9990 OVV FNPV209 K451406
WLAN5: QCA9990 OVV FNPV209 K451406
SERIAL: RS232 Port (115200 8n1) Cisco console cable and
4pin Serial Header | 3.3 | GND | RX | TX
MAC address for LAN1/LAN2/WLAN 2G/WLAN 5G in uboot env
* Installation via either RJ45 console or on-board 4 PIN header
Install Method
--------------
1) Setup TFTP server, and place
openwrt-ipq806x-generic-extreme_ap3935-initramfs-uImage image
in /srv/tftp or similar
2) Connect to console on router and connect ethernet port "LAN1" to
your LAN
3) Interupt the boot with any character
4) Login with admin/new2day for default password
(use reset/FactoryDefault if password needs to be reset)
5) Set serverip to TFTP IP: set serverip 192.168.1.2
6) Set ipaddr to another IP: set ipaddr 192.168.1.101
7) Make uboot ping something to activate eth0 on boot:
set bootcmd 'ping 192.168.1.1; run boot_flash'
saveenv
8) TFTP image to RAM:
tftpboot 0x42000000
openwrt-ipq806x-generic-extreme_ap3935i-initramfs-uImage
9) Boot image: bootm 0x42000000
In OpenWRT, "LAN1" is LAN, "LAN2" is WAN
10) SFTP openwrt-ipq806x-generic-extreme_ap3935-squashfs-nand-sysupgrade.bin
image to /tmp
11) sysupgrade /tmp/openwrt-*-nand-sysupgrade.bin
Signed-off-by: Glen Lee <g2lee@yahoo.com>
Modems which are using qmi do not reply on the 1st sync but they do
on subsequent. So qmi.sh is hanging on the first call. Since 2020 uqmi
supports a timeout parameter. Unfortunately qmi.sh didn't make use of
this parameter. So qmi.sh is now invoking an early dummy access to
unlock the modem
Signed-off-by: Uwe Niethammer <uwe@dr-niethammer.de>
Add missing PKG_MIRROR_HASH. This is always needed as is used to
generate and use a tar instead of git clone and validate the hash of it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Improve and update instructions on how to add board files and both
describe the needed step to upstream a board file or to use it locally.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The PKG_MIRROR_HASH is wrong, fix it.
Found and fixed using this command:
make package download check FIXUP=1
Fixes: c123e4f053 ("rtl8812au-ct: bump to fix kernel 6.1 compile")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Recent hostapd changes just edited the ucode files. It is required to
bump the PKG_RELEASE to include the newest changes in the latest builds.
Signed-off-by: Nick Hainke <vincent@systemli.org>
The mt76 driver usually reads the eeprom on the mtd partition at dts.
For emmc device we need to use caldata_extract script to read the
eeprom. However, the default eeprom file breaks the caldata script
execution, so remove it.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
When adding new router support, I found that uboot
could not recognize flash: "unknown raw ID xxx".
Sync SPI-NAND driver for mediatek to fixes this:
* Add support for Winbond W25N01KV 1Gbit chip.
* Add support for Etron SPI-NAND chip.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
If the full interface is restarted while bringing up an AP, it can trigger a
wpa_supplicant interface start before wpa_supplicant is notified of the
allocated mac addresses.
Fix this by moving the iface_update_supplicant_macaddr call to just after
the point where mac addresses are allocated.
Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The previous code handling the equal-condition might be removed or
altered in the future and the case might be overlooked.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Some users have their routers configured to supply a DHCP range that
includes the local interface address.
That worked with dnsmasq because it automatically skips the local
address.
Re-enable those existing configurations for the release and hint at
possible future problems.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
[ wrap commit description and remove unecessary text ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
To avoid confusion when working with ipcalc.sh, clarify that the last two
parameters belong to the range calculation and rename 'num' to the slightly
less ambiguous 'size'.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
In the dnsmasq init script, an off-by-one in the range calculation of
ipcalc.sh was mitigated by passing the limit as if its counting started
at zero. This patch removes the mitigation as the off-by-one has been
fixed.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Add a function 'ipcalc' to /lib/functions.sh that sets variables more
safely using export.
With this new function, dnsmasq also handles the return value of ipcalc
correctly.
Fixes: e4bd3de1be ("dnsmasq: refuse to add empty DHCP range")
Co-Authored-By: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Printing a broadcast address doesn't make any sense for /31 and /32
prefixes.
Strictly speaking, the same goes for the network address but it is useful
to get the first address in the prefix, e.g. to create a canonical
CIDR notation "$NETWORK/$PREFIX".
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
For /31 and /32 prefixes, there are only host addresses - no network and
broadcast address with all-zero and all-one bits.
Reflect this when setting the limit.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
The start and end addresses are inclusive.
Thus, adding num without substracting one results in num + 1 addresses.
Add the substraction and to implement the documented behaviour.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
- detect die revision used in variants of the Allwinner H616 SoC (H313, T507)
- support for H6 boards without PMIC
Tested on Pine64+ and Orange PI Zero2
Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
allow to overwrite the detected system capabilities e.g. if devices
does not operate as bridge.
Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
```
Specifications:
* CPU: Qualcomm IPQ8072A, SoC Version: 2.0, Quad core Cortex-A53 1.6896 GHz
* RAM: 1 GiB of DDR4 600 MHz
* Flash: NAND 2x256 MiB (Macronix MX30UF2G18AC)
* 4 RGB LEDs: Power, LAN, 2.4GHz and 5GHz
* UART: Two 4-pin unpopulated headers under the LEDs.
Use the header closest to LED 4 and 5.
They are marked with a white stroke.
TX RX GND, beginning from "4". 115200n8.
Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet (QCA8081)
Wlan:
* 4x4 in 2.4GHz: 802.11b/g/n/ax
* 4x4 in 5.0GHz: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 3.1/4.3 dBi (2.4GHz/5GHz)
Power:
* PoE+ 802.3at/af 25.5W
* DC 12V 2.5A
```
```
Note: The OpenWrt image is setup with DHCP and not a static IP.
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect to console on the AP, and connect the LAN port to your LAN
3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4. Set active_fw in env
# setenv active_fw 1
5. Transfer the initramfs image with TFTP
# setenv serverip 192.168.1.10 (IP of TFTP server host)
# setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
# tftpboot openwrt-qualcommax-ipq807x-netgear_wax620-initramfs-uImage.itb
6. Reboot and load the image
# bootm
7. SCP factory image to the AP
# scp openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi root@192.168.1.1:/tmp/
8. Connect to device using SSH (use the LAN port)
9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
# cat /proc/mtd (To check MTD partitions)
# ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi
10. Set active_fw to 0
# /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
# reboot
```
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Changes between 3.0.10 and 3.0.11 [19 Sep 2023]
* Fix POLY1305 MAC implementation corrupting XMM registers on Windows. ([CVE-2023-4807])
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
The patch refresh accidentally moved the hostapd_ucode_free_iface call to
the wrong function
Fixes: e9722aef9e ("hostapd: fix a crash when disabling an interface during channel list update")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Improve and package builds for various boot media configurations of the
MediaTek MT7981 reference board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When adding builds for MT7981 the related Makefile sections for MT7986
have apparently been copied, but in one instance the rename from 7986 to
7981 has been omitted. Fix that now.
Fixes: 602cb4f325 ("arm-trusted-firmware-mediatek: add build for MT7981 DDR3")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The PKG_CPE_ID links to NIST CPE version 2.2.
Assign PKG_CPE_ID to all remaining package which have a CPE ID.
Not every package has CPE id.
Related: https://github.com/openwrt/packages/issues/8534
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
New revision of eDPU uses an Marvell MV88E6361 switch to connect the SFP
cage and G.hn IC instead of connecting them directly to the ethernet
controllers.
In order to use the same image for both boards, U-Boot is responsible for
detecting the revision and enabling/disabling DTS nodes.
So, to make it easy for users, lets add the pending U-Boot patches to build
in OpenWrt.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
The ZTE MF287 requires a different board calibration file for ath10k than
the ZTE MF287+. The two devices receive their own DTS, thus the device tree
is slightly refactored.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Package and add dependencies to drm-amdgpu and drm-radeon for 6.1
* package acpi-video, drm-display-helper and drm-buddy
* add acpi-video, drm-display-helper and drm-buddy as dependencies for
drm-amdgpu
* add acpi-video and drm-display-helper as dependencies for drm-radeon
Signed-off-by: Pascal Coudurier <coudu@gmx.com>
Synchronize the ath11k backports with the current ath-next tree.
All of the changes are various bugfixes, there is no new major feature.
Signed-off-by: Robert Marko <robimarko@gmail.com>
