Fixes the regression so that targets that were installed via a feed can
also be build again with the Image Builder.
Fixes: 84ec8c4 ("imagebuilder: copy from buildroot only target/linux")
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Tested-by: Thomas Richard <thomas.richard@bootlin.com>
ttyS2 is the default console used for all rockchip boards.
The redundant 'console=tty1' parameter now breaks the console due to
recent procd update.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
We have hardware IOMMU support and this is totally unnecessary.
The given value is also unreasonable, it's too small and causes
kernel panic in some cases:
[ 5706.856473] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 28672 bytes), total 512 (slots), used 498 (slots)
[ 5706.864451] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 65536 bytes), total 512 (slots), used 464 (slots)
This parameter seems to be added by mistake, so remove it.
Fixes: e35c7ab51f ("rockchip: merge bootscript")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
6.6 has been in testing on qualcommax for a while so it should be in a
good shape, but lets default to it to get a wider audience.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Not having a journal by default is a major "gotcha".
Because openwrt does not fsck on boot, a power loss without journaling
can result in a dirty filesystem that openwrt will mount as read-only
which requires intervention to restore the router to working order.
Signed-off-by: Jordan Woyak <jordan.woyak@gmail.com>
- use Makefile.perf to prevent overriding MAKEFLAGS
- fix path to PKG_CONFIG
- link libstdc++ statically (only used for demangling)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The firmware blobs have all different licenses from the different
manufacturers of the binary blobs. This information is contained in the
upstream 'linux-firmware' repositroy.
This commit extends the package handling so that this information can be
added as an additional argument during packages generation.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
It's required to support NAND controllers with WP pin on boards that
don't have it connected to NAND chip.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Key features:
Allwinner H618 SoC (Quad core Cortex-A53)
1/1.5/2/4 GiB LPDDR4 DRAM
1 USB 2.0 type C port (Power + OTG)
1 USB 2.0 host port
1Gbps Ethernet port
Micro-HDMI port
MicroSD slot
Installation:
Write the image to SD Card with dd.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Backport AXP15060, AXP313a and AXP192 support.
The AXP15060 PMIC is used for starfive boards,
and the AXP313a PMIC is used for sunxi boards.
Remove conflicting patches from starfive target.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
This version supports LPDDR4 DRAM of H618 SoC.
Runtime-tested:
Olimex Olinuxino Micro (A20)
Orange Pi Zero 3 (H618)
Pine64 SoPine (A64)
Tested-by: Zoltan HERPAI <wigyori@uid0.hu>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Kernel 6.3 has introduced separate C45 read/write operations, and thus
split them out of the C22 operations completely so the old way of marking
C45 reads and writes via the register value does not work anymore.
This is causing SSDK to fail and find C45 only PHY-s such as Aquantia ones:
[ 22.187877] ssdk_phy_driver_init[371]:INFO:dev_id = 0, phy_adress = 8, phy_id = 0x0 phytype doesn't match
[ 22.209924] ssdk_phy_driver_init[371]:INFO:dev_id = 0, phy_adress = 0, phy_id = 0x0 phytype doesn't match
This in turn causes USXGMII MAC autoneg bit to not get set and then UNIPHY
autoneg will time out, causing the 10G ports not to work:
[ 37.292784] uniphy autoneg time out!
So, lets detect C45 reads and writes by the magic BIT(30) in the register
argument and if so call separate C45 mdiobus read/write functions.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix issue of transmitting abnormal data which leads to link problems
in 1G and 2.5G SerDes modes (SGMII, 1000Base-X, 2500Base-X) on the
MediaTek MT7988 SoC.
Link: b72d6cba92
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Zyxel GS1900-8 v2 or Rev.B1 is a newer variant of the GS1900-8, but
otherwise similar to the other GS1900 switches.
Differences
------------
* Front Button labeled RESTORE
* NO Power Switch on rear
* Serial Header next to the barrel power connector
* Part Number ends 0102F
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 8GB eMMC or 128 MB SPI-NAND
RAM: 256MB
Ethernet: 5x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset
USB: M.2(B-key) for 4G/5G Module
Power: DC 12V 1A
UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | VCC RX TX GND | <= |
| ----------------- |
--------------------------
The U-boot menu will automatically appear at startup, and then select
the required options through UP/DOWN Key.
NAND Flash and eMMC Flash instructions:
1. Set your computers IP adress to 192.168.1.2.
2. Run a TFTP server providing the sysupgrade.bin image.
3. Power on the router, into the U-Boot menu.
4. Select "2. Upgrade firmware"
5. Update sysupgrade.bin file name, input server IP and input device
IP (if they deviate from the defaults)
6. Wait for automatic startup after burning
Signed-off-by: Allen Zhao <allenzhao@unielecinc.com>
79f8cfa58ee7 ci: add github test workflow
428f40e7984f test commit fixing warnings
63058d1f81a5 ci: enable ujail builds
49ea930a862c utils: add key-value offset support to get_cmdline_val()
ca8c30208d5e inittab: fallback when multiple "console=" is detected
Required for the recent Elecom multiple console commits.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, both CI and local builds of wpa-supplicant will fail with:
/bin/sh: Argument list too long
Its happening as the argument list for mkdir in build.rules is too large
and over the MAX_ARG_STRLEN limit.
It seems that recent introduction of APK compatible version schema has
increased the argument size and thus pushed it over the limit uncovering
the issue.
Fixes: e8725a932e ("treewide: use APK compatible version schema")
Signed-off-by: Robert Marko <robimarko@gmail.com>
With the change in version schema the downloaded files changed, too,
mostly the hash is now prefixed with a tilde `~` instead of a dash `-`.
Since each downloaded archive contains folder with the same name as the
archive, the checksum changed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This is an automatically generated commit.
During a `git bisect` session, `git bisect --skip` is recommended.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
