This patch is required to be able to roam from one backhaul AP to
another one in the same ESS.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(daniel@makrotopia.org: PKG_REVISION bump and refreshed patches)
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
This patch allows other applications to get events management
frames (for example: association requests).
This is useful in Multi-AP context to be able to save association
requests from stations.
It has been sent to upstream hostapd in this series:
https://patchwork.ozlabs.org/project/hostap/list/?series=217500
'700-wifi-reload.patch' is updated due to the introduction of
'110-notify-mgmt-frames.patch'.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
dnsmasq v2.84rc2 has been promoted to release.
No functional difference between v2.83test3 and v2.84/v2.84rc2
Backport 2 patches to fix the version reporting
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Use new ubus-based hotplug call in dhcp-script.sh
As sysntpd now makes use of the new ubus-based hotplug calls, dnsmasq
no longer needs to ship ACL to cover ntpd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Commit 7c8c4f1be6 ("hostapd: fix P2P group information processing
vulnerability") was missing the actual patch for the vulnerability.
Fixes: 7c8c4f1be6 ("hostapd: fix P2P group information processing vulnerability")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
dnsmasq v2.83 has a bug in handling duplicate queries which means it may
try to reply using the incorrect network socket. This is especially
noticeable in dual stack environments where replies may be mis-directed to
IPv4 addresses on an IPv6 socket or IPv6 addresses on an IPv4 socket.
This results in system log spam such as:
dnsmasq[16020]: failed to send packet: Network unreachable
dnsmasq[16020]: failed to send packet: Address family not supported by protocol
dnsmasq v2.84test3 resolves these issues.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This fixes the following security problems in dnsmasq:
* CVE-2020-25681:
Dnsmasq versions before 2.83 is susceptible to a heap-based buffer
overflow in sort_rrset() when DNSSEC is used. This can allow a remote
attacker to write arbitrary data into target device's memory that can
lead to memory corruption and other unexpected behaviors on the target
device.
* CVE-2020-25682:
Dnsmasq versions before 2.83 is susceptible to buffer overflow in
extract_name() function due to missing length check, when DNSSEC is
enabled. This can allow a remote attacker to cause memory corruption
on the target device.
* CVE-2020-25683:
Dnsmasq version before 2.83 is susceptible to a heap-based buffer
overflow when DNSSEC is enabled. A remote attacker, who can create
valid DNS replies, could use this flaw to cause an overflow in a heap-
allocated memory. This flaw is caused by the lack of length checks in
rtc1035.c:extract_name(), which could be abused to make the code
execute memcpy() with a negative size in get_rdata() and cause a crash
in Dnsmasq, resulting in a Denial of Service.
* CVE-2020-25684:
A lack of proper address/port check implemented in Dnsmasq version <
2.83 reply_query function makes forging replies easier to an off-path
attacker.
* CVE-2020-25685:
A lack of query resource name (RRNAME) checks implemented in Dnsmasq's
versions before 2.83 reply_query function allows remote attackers to
spoof DNS traffic that can lead to DNS cache poisoning.
* CVE-2020-25686:
Multiple DNS query requests for the same resource name (RRNAME) by
Dnsmasq versions before 2.83 allows for remote attackers to spoof DNS
traffic, using a birthday attack (RFC 5452), that can lead to DNS
cache poisoning.
* CVE-2020-25687:
Dnsmasq versions before 2.83 is vulnerable to a heap-based buffer
overflow with large memcpy in sort_rrset() when DNSSEC is enabled. A
remote attacker, who can create valid DNS replies, could use this flaw
to cause an overflow in a heap-allocated memory. This flaw is caused
by the lack of length checks in rtc1035.c:extract_name(), which could
be abused to make the code execute memcpy() with a negative size in
sort_rrset() and cause a crash in dnsmasq, resulting in a Denial of
Service.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With encryption disabled, it was intended to set wpa_state=1 (enabled,
not configured) through the 'wps_not_configured' flag.
The flag is set appropriately but the condition using it is broken.
Instead, 'wps_configured' is checked and wpa_state is always 2 (enabled,
configured). Fix it by using the correct variable name.
Fixes: 498d84fc4e ("netifd: add wireless configuration support
and port mac80211 to the new framework")
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit title/message improvements]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The key_mgmt variable was mistyped when checking against "WPS", so
the if clause was never entered.
Fixes: f5753aae23 ("hostapd: add support for WPS pushbutton station")
Signed-off-by: Leon M. George <leon@georgemail.eu>
[add commit message, bump PKG_RELEASE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
'base' was never used.
Fixes: 498d84fc4e ("netifd: add wireless configuration support
and port mac80211 to the new framework")
Signed-off-by: Leon M. George <leon@georgemail.eu>
'enc_str' was never used.
Fixes: 498d84fc4e ("netifd: add wireless configuration support
and port mac80211 to the new framework")
Signed-off-by: Leon M. George <leon@georgemail.eu>
Granting capabilities CAP_NET_ADMIN and CAP_NET_RAW allows running
hostapd and wpa_supplicant without root priviledges.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This allows configuration of multicast_to_unicast and per_sta_vif options.
- multicast_to_unicast requests multicast-to-unicast conversion.
- per_sta_vif assigns each station its own AP_VLAN interface.
Signed-off-by: Etan Kissling <etan_kissling@apple.com>
To simplify the way netifd acquires the PIDs of wpa_supplicant and
hostapd let the config_add method of both of them return the PID of the
called process. Use the returned PID instead of querying procd when
adding wpa_supplicant configuration.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch enables hostapd.sh to properly configure wpa_supplicant
for when GCMP is used as cipher in station mode.
Without this wpa_supplicant will be unable to connect to AP.
This is needed for wil6210 as it does not support CCMP.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This adds an option "hostapd_bss_options" that does the same as
"hostapd_options" but on a per-BSS level, instead of a per-device level.
This can be used, for example, to configure different per-devce sae_passwords
per BSS or to augment some of the existing per-BSS options.
Signed-off-by: Florian Beverborg <flo@beverb.org>
[remove whitespace errors, bump release]
Signed-off-by: Paul Spooren <mail@aparcar.org>
This patch was already applied upstream and not needed here.
Fixes: 06403981e1 ("ppp: update to version 2.4.7.git-2019-05-06")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
b75bcad dhcpv6-ia: remove assignment equal to 0 checks
d1ae052 dhcpv6-ia: fix logic to include IA_PD prefix with lifetimes set to 0
9d5e379 dhcpv6-ia: fix prefix delegation behavior
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
As of hostapd upstream commit 7d2ed8ba "Remove CONFIG_IEEE80211W build parameter"
https://w1.fi/cgit/hostap/commit?id=7d2ed8bae86a31dd2df45c24b3f7281d55315482
802.11w feature is always enabled in the build time.
It doesn't make sense to opt-in 802.11w per driver as hostapd will always
be compiled with this feature enabled.
As suggested by Hauke Mehrtens, for now keep 11w enabled in build_features.h
for compatibility reasons. This option will be dropped when LuCI is adjusted.
Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
When hostapd gets restarted to often/quickly will cause procd to not restart it
anymore. it will think that hapd is in a crash loop.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [adjust respawn time]
Currently, EAPOLv2 (802.1X-2004) is used by default for legacy clients that
are not WPA2 (RSN) capable. These legacy clients are often intolerant to this
EAPOL version and fail to connect.
hostapd.conf upstream documents for eapol_version the following and that this
is a known compatibility issue with version 2:
// IEEE 802.1X/EAPOL version
// hostapd is implemented based on IEEE Std 802.1X-2004 which defines EAPOL
// version 2. However, there are many client implementations that do not handle
// the new version number correctly (they seem to drop the frames completely).
// In order to make hostapd interoperate with these clients, the version number
// can be set to the older version (1) with this configuration value.
// Note: When using MACsec, eapol_version shall be set to 3, which is
// defined in IEEE Std 802.1X-2010.
//eapol_version=2
For the wpa parameter, hostapd.conf upstream documents that this is a bitfield,
configured as follows:
// Enable WPA. Setting this variable configures the AP to require WPA (either
// WPA-PSK or WPA-RADIUS/EAP based on other configuration). For WPA-PSK, either
// wpa_psk or wpa_passphrase must be set and wpa_key_mgmt must include WPA-PSK.
// Instead of wpa_psk / wpa_passphrase, wpa_psk_radius might suffice.
// For WPA-RADIUS/EAP, ieee8021x must be set (but without dynamic WEP keys),
// RADIUS authentication server must be configured, and WPA-EAP must be included
// in wpa_key_mgmt.
// This field is a bit field that can be used to enable WPA (IEEE 802.11i/D3.0)
// and/or WPA2 (full IEEE 802.11i/RSN):
// bit0 = WPA
// bit1 = IEEE 802.11i/RSN (WPA2) (dot11RSNAEnabled)
// Note that WPA3 is also configured with bit1 since it uses RSN just like WPA2.
// In other words, for WPA3, wpa=2 is used the configuration (and
// wpa_key_mgmt=SAE for WPA3-Personal instead of wpa_key_mgmt=WPA-PSK).
//wpa=2
For client compatibility therefore:
EAPOLv1 (802.1X-2001) should be used by default where WPA is enabled.
EAPOLv2 (802.1X-2004) should be used by default where WPA is disabled.
To fix this, we can therefore change in the script:
set_default eapol_version 0
To the following:
set_default eapol_version $((wpa & 1))
This therefore:
1) Sets eapol_version to 1 where WPA has been enabled via wpa bit0 being set.
2) Sets eapol_version to 0 where WPA has been disabled via wpa bit0 being unset.
For usual configurations that only have WPA2 enabled, EAPOLv2 is then used.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
hostapd.sh does not parse skip_inactivity_poll boolean from
/etc/config/wireless despite being mentioned in the documentation [1].
This change fixes this, and by default sets its value to 0 [1].
[1] https://openwrt.org/docs/guide-user/network/wifi/basic
Signed-off-by: Nadim Atiya <nadim.atiya@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[fix and reformat commit message, make patch apply]
So we can ship px5g-wolfssl by default in the release image, but still
make the HTTPS for LuCI optional. This small change with addition of
`CONFIG_PACKAGE_px5g-wolfssl=y` into the buildbot's seed config for the
next release should provide optional HTTPS in the next release.
Disabling the current default automatic uhttpd's redirect to HTTPS
should make the HTTPS optional. That's it, user would either need to
switch to HTTPS by manually switching to https:// protocol in the URL or
by issuing the following commands to make the HTTPS automatic redirect
permanent:
$ uci set uhttpd.main.redirect_https=1
$ uci commit uhttpd
$ service uhttpd reload
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Bump package version after previous changes.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
[added missing commit description]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
binary size cost is much less than 1k.
tested on ath79/generic:
bin: 215128 -> 215132 (+4b)
ipk: 111183 -> 111494 (+311b)
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
this commit removes manual recipes for options and introduces mapping lists:
- DB_OPT_COMMON holds option mappings which are common for all builds;
- DB_OPT_CONFIG holds option mappings which are depend on config settings.
DB_OPT_COMMON is space-separated list of 'words', each of them is in format:
'header_option|value'
'header_option' is added with value 'value' to 'localoptions.h'.
if 'header_option' is preceded by two exclamation marks ('!!')
then option is not added to 'localoptions.h' but replaced in 'sysoptions.h'.
in short:
option|value - add option to localoptions.h
!!option|value - replace option in sysoptions.h
DB_OPT_CONFIG is space-separated list of 'words', each of them is in format:
'header_option|config_variable|value_enabled|value_disabled'
'header_option' is handled likewise in DB_OPT_COMMON.
if 'config_variable' is enabled (technically: not disabled)
then 'header_option' is set to 'value_enabled' and 'value_disabled' otherwise.
in short:
option|config|enabled|disabled = add option to localoptions.h
!!option|config|enabled|disabled = replace option in sysoptions.h
option := (config) ? enabled : disabled
If you're not sure that option's value doesn't have '|' within - add your recipe
manually right after '$(Build/Configure/dropbear_headers)' and write some words
about your decision.
PS about two exclamation marks:
early idea was to use one exclamation mark to denote such header options
but then i thought single exclamation mark may be overlooked by mistake.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
- add two helper functions to avoid mistakes with
choice of correct header file to work with
- update rules accordingly
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
put static options at first place, then place configurable options.
also put DROPBEAR_ECC right before DROPBEAR_ECC_FULL to ease maintainance.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
this option was disabled in 2011 and these long nine years showed us that change was definitely wrong.
binary size cost is much less than 1k.
tested on ath79/generic:
bin: 215128 -> 215128 (no change)
ipk: 111108 -> 111183 (+75b)
Fixes: 3c801b3dc0 ("tune some more options by default to decrease size")
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
The lldpd sources ship a modified local AX_LIB_READLINE M4 macro which
conflicts with the official macro shipped by autoconf-archive.
Due to the official macro having the same name and a higher serial
number, autoconf will prefer including that one instead of the local
copy, preventing the substitution of @READLINE_LIBS@ in Makefile.in
templates, ultimately leading to the following build failure when
linking lldpcli:
...-gcc: error: READLINE_LIBS@: No such file or directory
Avoid this problem by renaming the locally shipped macro to not clash
with the official implementation anymore.
Ref: https://github.com/lldpd/lldpd/pull/423
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Set legacy_rates to 0 by default to disable 802.11b data rates by default.
The time has long come where 802.11b DSSS/CCK data rates should be disabled
by default in OpenWRT. Users in need of 802.11b client support can reasonably
enable these where they are needed.
The balance of equities has significantly, and for a long time, tipped
such that dropping backwards compatibility by default with 802.11b
devices is appropriate, proportionate and justified. By doing so,
management and control traffic is moved by default to a 20
MHz wide 6 Mb/s OFDM data rate instead of a 22 MHz wide 1 Mb/s DSSS data
rate. This is significantly more airtime efficient.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
This should fix an issue when user have a router with enabled seccomp
and tries to run umdns package which was build with SDK with disabled
seccomp support.
Signed-off-by: Jan Pavlinec <jan.pavlinec@nic.cz>
Add a cell_density option to configure data rates for normal, high and
very high cell density wireless deployments.
The purpose of using a minimum basic/mandatory data rate that is higher
than 6 Mb/s, or 5.5 Mb/s (802.11b compatible), in high cell density
environments is to transmit broadcast/multicast data frames using less
airtime or to reduce management overheads where significant co-channel
interference (CCI) exists and cannot be avoided.
Caution: Without careful design and validation, configuration of a too
high minimum basic/mandatory data rate can sacrifice connection stability
or disrupt the ability to reliably connect and authenticate for little to
no capacity benefit. This is because this configuration affects the
ability of clients to hear and demodulate management, control and
broadcast/multicast data frames.
Deployments that have not been specifically designed and validated are
usually best suited to use 6, 12 and 24 Mb/s as basic/mandatory data
rates.
Only usually seek to configure a 12 Mb/s, or 11 Mb/s (802.11b
compatible), minimum basic/mandatory rate in high cell density
deployments that have been designed and validated for this.
For many deployments, the minimum basic/mandatory data rate should not be
configured above 12 Mb/s to 18 Mb/s, 24 Mb/s or higher. Such a
configuration is only appropriate for use in very high cell density
deployment scenarios.
A cell_density of Very High (3) should only be used where a deployment
has a valid use case and has been designed and validated specifically for
this use, nearly always with highly directional antennas - an example
would be stadium deployments. For example, with a 24 Mb/s OFDM minimum
basic/mandatory data rate, approximately a -73 dBm RSSI is required to
decode frames. Many clients will not have roamed elsewhere by the time
that they experience -73 dBm and, where they do, they frequently may not
hear and be able to demodulate beacon, control or broadcast/multicast
data frames causing connectivity issues.
There is a myth that disabling lower basic/mandatory data rates will
improve roaming and avoid sticky clients. For 802.11n, 802.11ac and
802.11ax clients this is not correct as clients will shift to and use
lower MCS rates and not to the 802.11b or 802.11g/802.11a rates that are
able to be used as basic/mandatory data rates.
There is a myth that disabling lower basic/mandatory data rates will
ensure that clients only use higher data rates and that better
performance is assured. For 802.11n, 802.11ac and 802.11ax clients this
is not correct as clients will shift around and use MCS rates and not the
802.11b or 802.11g/802.11a rates that able to be used as basic/mandatory
data rates.
Cell Density
0 - Disabled (Default)
Setting cell_density to 0 does not configure data rates. This is the
default.
1 - Normal Cell Density
Setting cell_density to 1 configures the basic/mandatory rates to 6, 12
and 24 Mb/s OFDM rates where legacy_rates is 0. Supported rates lower
than the minimum basic/mandatory rate are not offered.
Setting cell_density to 1 configures the basic/mandatory rates to the 5.5
and 11 Mb/s DSSS rates where legacy_rates is 1. Supported rates lower
than the minimum basic/mandatory rate are not offered.
2 - High Cell Density
Setting the cell_density to 2 configures the basic/mandatory rates to the
12 and 24 Mb/s OFDM rates where legacy_rates is 0. Supported rates lower
than the minimum basic/mandatory rate are not offered.
Setting the cell_density to 2 configures the basic/mandatory rates to the
11 Mb/s DSSS rate where legacy_rates is 1. Supported rates lower than the
minimum basic/mandatory rate are not offered.
3 - Very High Cell Density
Setting the cell_density to 3 configures the basic/mandatory rates to the
24 Mb/s OFDM rate where legacy_rates is 0. Supported rates lower than the
minimum basic/mandatory rate are not offered.
Setting the cell_density to 3 only has effect where legacy_rates is 0,
else this has the same effect as being configured with a cell_density of 2.
Where specified, the basic_rate and supported_rates options continue to
override both the cell_density and legacy_rates options.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Several variables in hostapd.sh can be used uninitialized in numerical
comparisons, causing errors in logread:
netifd: radio24 (1668): sh: out of range
Set defaults for those variables to silence those errors.
Fixes: b518f07d4b ("hostapd: remove ieee80211v option")
Fixes: cc80cf53c5 ("hostapd: add FTM responder support")
Fixes: e66bd0eb04 ("hostapd: make rrm report independent of ieee80211k setting")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Fixes the offset of the patch added in 93bbd998aa
("hostapd: enter DFS state if no available channel is found").
Signed-off-by: Leon M. George <leon@georgemail.eu>
This sets the validity interval for the BSS transition candidate
list to the same value as the disassociation timer.
Currently the value is always 0, which is the specification states is a
reserved value. Also, wpa_supplicant and from the looks of it some
Android implementations will outright ignore the candidate list in this
case.
Signed-off-by: David Bauer <mail@david-bauer.net>
* Add support for passing airtime_sta_weight into hostapd configuration.
* Since that commit it is possible to configure station weights. Set higher
value for larger airtime share, lower for smaller share.
I have tested this functionality by modyfing /etc/config/wireless to:
config wifi-device 'radio0'
...
option airtime_mode '1'
config wifi-iface 'default_radio0'
...
list airtime_sta_weight '01:02:03:04:05:06 1024'
Now, when the station associates with the access point it has been assigned
a higher weight value.
root@OpenWrt:~# cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan0/stations/01\:02\:03\:04\:05\:06/airtime
RX: 12656 us
TX: 10617 us
Weight: 1024
Deficit: VO: -2075 us VI: 256 us BE: -206 us BK: 256 us
[MAC address has been changed into a dummy one.]
Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
airtime_mode is always parsed as an empty string since it hasn't been
added into hostapd_common_add_device_config function.
Fixes: e289f183 ("hostapd: add support for per-BSS airtime configuration")
Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
This adds a new get_status method to a hostapd interface, which
provides information about the current interface status.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds information from mac80211 to hostapd get_client ubus function.
This way, TX as well as RX status information as well as the signal can
be determined.
Signed-off-by: David Bauer <mail@david-bauer.net>
procd-seccomp switched to OCI-compliant seccomp parser instead of our
(legacy, OpenWrt-specific) format. Convert ruleset to new format.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update dropbear to latest stable 2.81; for the changes see https://matt.ucc.asn.au/dropbear/CHANGES
Refresh patches
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* noise: take lock when removing handshake entry from table
This is a defense in depth patch backported from upstream to account for any
future issues with list node lifecycles.
* netns: check that route_me_harder packets use the right sk
A test for an issue that goes back to before Linux's git history began. I've
fixed this upstream, but it doesn't look possible to put it into the compat
layer, as it's a core networking problem. But we still test for it in the
netns test and warn on broken kernels.
* qemu: drop build support for rhel 8.2
We now test 8.3+.
* compat: SYM_FUNC_{START,END} were backported to 5.4
* qemu: bump default testing version
The real motivation for this version bump: 5.4.76 made a change that broke our
compat layer.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Allow configuring ipsets with dedicated config sections:
config ipset
list name 'ss_rules_dst_forward'
list name 'ss_rules6_dst_forward'
list domain 't.me'
list domain 'telegram.org'
instead of current, rather inconvenient syntax:
config dnsmasq
...
list ipset '/t.me/telegram.org/ss_rules_dst_forward,ss_rules6_dst_forward'
Current syntax will still continue to work though.
With this change, a LuCI GUI for DNS ipsets should be easy to implement.
Signed-off-by: Aleksandr Mezin <mezin.alexander@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
The uhttpd package takes care of creating self-signed certificates if
px5g is installed. This improves the security of router management as it
encrypts the LuCI connection.
The EC P-256 curve is faster than RSA which which improves the user
experience on embedded devices. EC P-256 is support for as old devices
as Android 4.4.
Signed-off-by: Paul Spooren <mail@aparcar.org>
If only AP mode is needed, this is currently the most space-efficient way to
provide support for WPA{2,3}-PSK, 802.11w and 802.11r.
openwrt-ath79-generic-ubnt_nanostation-loco-m-squashfs-sysupgrade.bin sizes:
4719426 bytes (with wpad-basic-wolfssl)
4457282 bytes (with hostapd-basic-wolfssl)
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Hotspot 2.0 AP features have been made available in the -full variants
of hostapd and wpad. Hence we no longer need a seperate package for
that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add OpenSSL-linked basic variants (which provides WPA-PSK only, 802.11r and
802.11w) of both hostapd and wpad. For people who don't need the full hostapd
but are stuck with libopenssl for other reasons, this saves space by avoiding
the need of an additional library (or a larger hostapd with built-in crypto).
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
This adds missing config symbols for interworking as well as Hotspot 2.0
to the wpa_supplicant-full configuration.
These symbols were added to the hostapd-full configuration prior to this
commit. Without adding them to the wpa_supplicant configuration,
building of wpad-full fails.
Thanks to Rene for reaching out on IRC.
Fixes: commit be9694aaa2 ("hostapd: add UCI support for Hotspot 2.0")
Fixes: commit 838b412cb5 ("hostapd: add interworking support")
Signed-off-by: David Bauer <mail@david-bauer.net>
/etc/hotplug.d/ntp/25-dnsmasqsec is being sourced by /sbin/hotplug-call
running as ntpd user. For that to work the file needs to be readable by
that user.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds configuration options to enable interworking for hostapd.
All options require iw_enabled to be set to 1 for a given VAP.
All IEEE802.11u related settings are supported with exception of the
venue information which will be added as separate UCI sections at a
later point.
The options use the same name as the ones from the hostapd.conf file
with a "iw_" prefix added.
All UCI configuration options are passed without further modifications
to hostapd with exceptions of the following options, whose elements can
be provided using UCI lis elements:
- iw_roaming_consortium
- iw_anqp_elem
- iw_nai_realm
- iw_domain_name
- iw_anqp_3gpp_cell_net
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds support for enabling the FTM responder flag for the APs
extended capabilities. On supported hardware, enabling the ftm_responder
config key for a given AP will enable the FTM responder bit.
FTM support itself is unconditionally implemented in the devices
firmware (ath10k 2nd generation with 3.2.1.1 firmware). There's
currently no softmac implementation.
Also allow to configure LCI and civic location information which can be
transmitted to a FTM initiator.
Signed-off-by: David Bauer <mail@david-bauer.net>
Remove the ieee80211v option. It previously was required to be enabled
in order to use time_advertisement, time_zone, wnm_sleep_mode and
bss_transition, however it didn't enable any of these options by default.
Remove it, as configuring these options independently is enough.
This change does not influence the behavior of any already configured
setting.
Signed-off-by: David Bauer <mail@david-bauer.net>
Allow to configure both RRM beacon as well as neighbor reports
independently and only enable them by default in case the ieee80211k
config option is set.
Signed-off-by: David Bauer <mail@david-bauer.net>
59e4fc98162d cache: cache_answer: fix off by one
4cece9cc7db4 cache: cache_record_find: fix buffer overflow
be687257ee0b cmake: tests: provide umdns-san binary
bf01f2dd0089 tests: add dns_handle_packet_file tool
134afc728846 tests: add libFuzzer based fuzzing
de08a2c71ca8 cmake: create static library
cdc18fbb3ea8 interface: fix possible null pointer dereference
1fa034c65cb6 interface: fix value stored to 'fd' is never read
3a67ebe3fc66 Add initial GitLab CI support
50caea125517 cmake: fix include dirs and libs lookup
Signed-off-by: Petr Štetiar <ynezz@true.cz>
For IPv6 native connections when using IPv6 DNS lookups, there is no
valid default resolver if ignoring WAN DHCP provided nameservers.
This uses a runtime check to determine if IPv6 is supported on the host.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
ntpd in packages feed had already a user 'ntp' with UID 123 declared.
Rename the username of busybox-ntpd to be 'ntp' instead of 'ntpd' so
it doesn't clash.
Reported-by: Etienne Champetier <champetier.etienne@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Expose WPS ubus API only if compiled with WPS support and add new
handler for wps_status call.
Also add '-v wps' option to check whether WPS support is present in
hostapd.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is useful to bring up multiple client mode interfaces on a single
channel much faster without having to scan through a lot of channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It should return false to indicate that the option should not be ignored
Fixes 064dc1e8 ("dnsmasq: abort when dnssec requested but not
available")
Reported-by: Sami Olmari <sami@olmari.fi>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The TFTP server provided by dnsmasq supports serving a select boot image
based on the client's MAC or IP address. This allows an administrator
to activate this feature in /etc/config/dhcp. Here is an example
/etc/config/dhcp that configures dnsmasq with --tftp-unique-root=mac:
...
config dnsmasq
option enable_tftp 1
option tftp_root /usr/libexec/tftpboot
option tftp_unique_root mac
config boot router
option serveraddress 192.168.1.1
option servername tftp.example.com
option filename openwrt-initramfs-kernel.bin
...
With this configuration, dnsmasq will serve
/usr/libexec/tftpboot/00-11-22-33-44-55/openwrt-initramfs-kernel.bin to
the client with MAC address 00:11:22:33:44:55.
Signed-off-by: W. Michael Petullo <mike@flyn.org>
Make the BSSID and SSID fields optional when configuring a neighbor
report into hostapd.
Both options can now be an empty string. For the BSSID, the first 6 byte
are copied from the neighbor report. For the SSID, the SSID for the
affected hostapd BSS is used.
Signed-off-by: David Bauer <mail@david-bauer.net>
Rafal Milecki pointed out that ubus events are meant for low-level ubus
events only (e.g. addition or removal of an object). Higher level
events should happen as notifications on the ubus object itself.
Dispatch BSS events on the main hostapd ubus object instead of
publishing them as ubus events.
Signed-off-by: David Bauer <mail@david-bauer.net>
hostapd will emit a ubus event with the eventname hostapd.<ifname>.<event>
when adding, removing or reloading a BSS.
This way, services which install state (for example the RMM neighbor
list) can on-demand reinstall this information for the BSS without
polling this state.
Signed-off-by: David Bauer <mail@david-bauer.net>
UCI defaults scripts are supposed to be numbered, but odhcpd's lacked numbering, which
turned out to mess up my custom scripts numbered 9[0-9]_*. The idea is to have high number
(custom) scripts executed last. Jow confirmed numbering is the default case, not the
exception (thanks).
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Add support for per-BSS airtime weight configuration. This allows to set
a airtime weight per BSS as well as a ratio limit based on the weight.
Support for this feature is only enabled in the full flavors of hostapd.
Consult the hostapd.conf documentation (Airtime policy configuration)
for more information on the inner workings of the exposed settings.
Signed-off-by: David Bauer <mail@david-bauer.net>
Don't use bash syntax, because /bin/sh is used here.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[bump PKG_RELEASE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* compat: backport kfree_sensitive and switch to it
* netlink: consistently use NLA_POLICY_EXACT_LEN()
* netlink: consistently use NLA_POLICY_MIN_LEN()
* compat: backport NLA policy macros
Backports from upstream changes.
* peerlookup: take lock before checking hash in replace operation
A fix for a race condition caught by syzkaller.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
The Ed25519 key pairs are much shorter than RSA pairs and are supported
by default in OpenSSH. Looking at websites explaining how to create new
SSH keys, many suggest using Ed25519 rather than RSA, however consider
the former as not yet widely established. OpenWrt likely has a positive
influence on that development.
As enabling Ed25519 is a compile time option, it is currently not
possible to install the feature via `opkg` nor select that option in an
ImageBuilder.
Due to the size impact of **12kB** the option should only be enabled for
devices with `!SMALL_FLASH`.
This approach seems cleaner than splitting `dropbear` into two packages
like `dropbear` and `dropbear-ed25519`.
Signed-off-by: Paul Spooren <mail@aparcar.org>
af30be0 Fix setting prefix for IPv6 link-local addresss
0314df4 Disable asking password again when prompt program returns 128
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This fixes the following compile errors after the wolfssl 4.5.0 update:
LD wpa_cli
../src/crypto/tls_wolfssl.c: In function 'tls_match_alt_subject':
../src/crypto/tls_wolfssl.c:610:11: error: 'GEN_EMAIL' undeclared (first use in this function); did you mean 'ENAVAIL'?
type = GEN_EMAIL;
^~~~~~~~~
ENAVAIL
../src/crypto/tls_wolfssl.c:610:11: note: each undeclared identifier is reported only once for each function it appears in
../src/crypto/tls_wolfssl.c:613:11: error: 'GEN_DNS' undeclared (first use in this function)
type = GEN_DNS;
^~~~~~~
../src/crypto/tls_wolfssl.c:616:11: error: 'GEN_URI' undeclared (first use in this function)
type = GEN_URI;
^~~~~~~
../src/crypto/tls_wolfssl.c: In function 'wolfssl_tls_cert_event':
../src/crypto/tls_wolfssl.c:902:20: error: 'GEN_EMAIL' undeclared (first use in this function); did you mean 'ENAVAIL'?
if (gen->type != GEN_EMAIL &&
^~~~~~~~~
ENAVAIL
../src/crypto/tls_wolfssl.c:903:20: error: 'GEN_DNS' undeclared (first use in this function)
gen->type != GEN_DNS &&
^~~~~~~
../src/crypto/tls_wolfssl.c:904:20: error: 'GEN_URI' undeclared (first use in this function)
gen->type != GEN_URI)
^~~~~~~
Makefile:2029: recipe for target '../src/crypto/tls_wolfssl.o' failed
Fixes: 00722a720c ("wolfssl: Update to version 4.5.0")
Reported-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Abort the dhcp-check based on the interface instead of the carrier
state. In cases where the interface is up but the carrier is down,
netifd won't cause a dnsmasq reload, thus dhcp won't become active
on this interface.
Signed-off-by: David Bauer <mail@david-bauer.net>
If not needed, disabling scp allows for a nice size reduction.
Dropbear executable size comparison:
153621 bytes (baseline)
133077 bytes (without scp)
In other words, we trim a total of 20544 bytes.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
The ssh symlink was still being created even when dbclient was disabled in the
build configuration. Fix this annoyance.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
677aa53 Fix -W option for pppoe-discovery utility (#157)
115c419 Accept Malformed Windows Success Message (#156)
5bdb148 pppd: Add documentation of stop-bits option to pppd man page (#154)
2a7981f Add ipv6cp-accept-remote option
0678d3b pppd: Fix the default value for ipv6cp-accept-local to false
Refresh patches
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The hostapd configuration logic is supposed to accept "option key" as
legacy alias for "option auth_secret". This particular fallback option
failed to work though because "key" was not a registered configuration
variable.
Fix this issue by registering the "key" option as well, similar to the
existing "server" nad "port" options.
Ref: https://github.com/openwrt/openwrt/pull/3282
Suggested-by: Michael Jones <mike@meshplusplus.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
If an existing "wpa_psk_file" is passed to hostapd, the "key" option may
be omitted.
While we're at it, also improve the passphrase length checking to ensure
that it is either exactly 64 bytes or 8 to 63 bytes.
Fixes: FS#2689
Ref: https://github.com/openwrt/openwrt/pull/3283
Suggested-by: Michael Jones <mike@meshplusplus.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add package which provides size optimized wpad with support for just
WPA-PSK, SAE (WPA3-Personal), 802.11r and 802.11w.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[adapt to recent changes, add dependency for WPA_WOLFSSL config]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Before this commit, if uci option "dnssec" was set, we pass "--dnssec"
and friends to dnsmasq, let it start and decide whether to quit and
whether to emit message for diagnosis
# dnsmasq --dnssec; echo $?
dnsmasq: DNSSEC not available: set HAVE_DNSSEC in src/config.h
1
DNSSEC as a feature is different from others like dhcp, tftp in that
it's a security feature. Better be explicit. With this change
committed, we make it so by not allowing it in the first in the
initscript, should dnsmasq later decides to not quit (not likely) or
quit without above explicit error (unlikely but less so ;)
So this is just being proactive. on/off choices with uci option
"dnssec" are still available like before
Link: https://github.com/openwrt/openwrt/pull/3265#issuecomment-667795302
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
With the introduction of the generic OpenVPN hotplug mechanism, wrapped
--up and --down scripts got the wrong amount and order of arguments passed,
breaking existing configurations and functionality.
Fix this issue by passing the same amount of arguments in the same expected
order as if the scripts were executed by the OpenVPN daemon directly.
Ref: https://github.com/openwrt/openwrt/pull/1596#issuecomment-668935156
Fixes: 8fe9940db6 ("openvpn: add generic hotplug mechanism")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
212f836 ubus: rename JSON-RPC format related functions
628341f ubus: use local "blob_buf" in uh_ubus_handle_request_object()
9d663e7 ubus: use BLOBMSG_TYPE_UNSPEC for "params" JSON attribute
77d345e ubus: drop unused "obj" arguments
8d9e1fc ubus: parse "call" method params only for relevant call
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* compat: rhel 8.3 beta removed nf_nat_core.h
* compat: ipv6_dst_lookup_flow was ported to rhel 7.9 beta
This compat tag adds support for RHEL 8.3 beta and RHEL 7.9 beta, in addition
to RHEL 8.2 and RHEL 7.8. It also marks the first time that
<https://www.wireguard.com/build-status/> is all green for all RHEL kernels.
After quite a bit of trickery, we've finally got the RHEL kernels building
automatically.
* compat: allow override of depmod basedir
When building in an environment with a different modules install path, it's
not possible to override the depmod basedir flag by setting the DEPMODBASEDIR
environment variable.
* compat: add missing headers for ip_tunnel_parse_protocol
This fixes compilation with some unusual configurations.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Update the openvpn sample configurations to use modern options in favor
of deprecated ones, suggest more sane default settings and add some
warnings.
* Add tls_crypt and ncp_disable to the sample configuration
* Replace nsCertType with remote_cert_tls in client sample configuration
* Comment out "option compress", compression should not be preferred
* Advise 2048-bit Diffie-Hellman parameters by default
* Add warnings about compression and use of Blowfish (BF-CBC)
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
When retrieving the PID for hostapd and wpa_supplicant via ubus the
wrong service name is currently used. This leads to the following error
in the log:
netifd: radio0 (1409): WARNING (wireless_add_process):
executable path /usr/sbin/wpad does not match process path (/proc/exe)
Fixing the service name retrieves the correct PID and therefore the
warning won't occur.
Signed-off-by: David Bauer <mail@david-bauer.net>
The current selection of DRIVER_MAKEOPTS and TARGET_LDFLAGS is
exceptionally hard to read. This tries to make things a little
easier by inverting the hierarchy of the conditions, so SSL_VARIANT
is checked first and LOCAL_VARIANT is checked second.
This exploits the fact that some of the previous conditions were
unnecessary, e.g. there is no hostapd-mesh*, so we don't need
to exclude this combination.
It also should make it a little easier to see which options are
actually switched by SSL_VARIANT and which by LOCAL_VARIANT.
The patch is supposed to be cosmetic.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For a few packages, the current TITLE is too long, so it is not
displayed at all when running make menuconfig. Despite, there is
no indication of OpenSSL vs. wolfSSL in the titles.
Thus, this patch adjusts titles to be generally shorter, and adds
the SSL variant to it.
While at it, make things easier by creating a shared definition for
eapol-test like it's done already for all the other flavors.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Drop outdated and by now broken patchset originally supplied by
Peter Oh in August 2018 but never merged upstream.
Instead add the more promissing rework recently submitted by
Markus Theil who picked up Peter's patchset, fixed and completed it
and added support for HE (802.11ax) in mesh mode.
This is only compile tested and needs some real-life testing.
Fixes: FS#3214
Fixes: 167028b750 ("hostapd: Update to version 2.9 (2019-08-08)")
Fixes: 0a3ec87a66 ("hostapd: update to latest Git hostap_2_9-1238-gdd2daf0848ed")
Fixes: 017320ead3 ("hostapd: bring back mesh patches")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If using a configuration file for OpenVPN, allow overriding name of the
interface. The reason is that then people could use configuration file
provided by VPN provider directly and override the name of the interface
to include it in correct firewall zone without need to alter the
configuration file.
Signed-off-by: Michal Hrusecky <michal@hrusecky.net>
(cherry picked from commit c93667358515ec078ef4ac96393623ac084e5c9e)
Split out code that parses openvpn configuration file into separate file
that can be later included in various scripts and reused.
Signed-off-by: Michal Hrusecky <michal@hrusecky.net>
(cherry picked from commit 86d8467c8ab792c79809a08c223dd9d40da6da2e)
Previously hostapd would not stop transmitting when a DFS event was
detected and no available channel to switch to was available.
Disable and re-enable the interface to enter DFS state. This way, TX
does not happen until the kernel notifies hostapd about the NOP
expiring.
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes a nasty problem introduced in 2.81 which causes random
crashes on systems where there's significant DNS activity over TCP. It
also fixes DNSSEC validation problems with zero-TTL DNSKEY and DS
records.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This release brings parity with the commits Linus released a few hours
ago into 5.8-rc5.
* receive: account for napi_gro_receive never returning GRO_DROP
The napi_gro_receive function no longer returns GRO_DROP ever, making
handling GRO_DROP dead code. This commit removes that dead code.
Further, it's not even clear that device drivers have any business in
taking action after passing off received packets; that's arguably out of
their hands.
* device: implement header_ops->parse_protocol for AF_PACKET
WireGuard uses skb->protocol to determine packet type, and bails out if
it's not set or set to something it's not expecting. For AF_PACKET
injection, we need to support its call chain of:
packet_sendmsg -> packet_snd -> packet_parse_headers ->
dev_parse_header_protocol -> parse_protocol
Without a valid parse_protocol, this returns zero, and wireguard then
rejects the skb. So, this wires up the ip_tunnel handler for layer 3
packets for that case.
* queueing: make use of ip_tunnel_parse_protocol
Now that wg_examine_packet_protocol has been added for general
consumption as ip_tunnel_parse_protocol, it's possible to remove
wg_examine_packet_protocol and simply use the new
ip_tunnel_parse_protocol function directly.
* compat: backport ip_tunnel_parse_protocol and ip_tunnel_header_ops
These are required for moving wg_examine_packet_protocol out of
wireguard and into upstream.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Upstream in commit 972d723484d8 ("split signkey_type and signature_type
for RSA sha1 vs sha256") has added strict checking of pubkey algorithms
which made keys with SHA-256 hashing algorithm unusable as they still
reuse the `ssh-rsa` public key format. So fix this by disabling the
check for `rsa-sha2-256` pubkeys.
Ref: https://tools.ietf.org/html/rfc8332#section-3
Fixes: d4c80f5b17 ("dropbear: bump to 2020.80")
Tested-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This replaces deprecated backticks by more versatile $(...) syntax.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[add commit description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Backport patches which fix compile issue for uClibc-ng :
dbrandom.c:174:8: warning: implicit declaration of function 'getrandom'; did you mean 'genrandom'? [-Wimplicit-function-declaration]
ret = getrandom(buf, sizeof(buf), GRND_NONBLOCK);
^~~~~~~~~
genrandom
dbrandom.c:174:36: error: 'GRND_NONBLOCK' undeclared (first use in this function); did you mean 'SOCK_NONBLOCK'?
ret = getrandom(buf, sizeof(buf), GRND_NONBLOCK);
^~~~~~~~~~~~~
SOCK_NONBLOCK
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* compat: drop centos 8.1 support as 8.2 is now out
Of note, as well, is that we now have both RHEL7 and RHEL8 in our CI at
<https://www.wireguard.com/build-status/>.
* Kbuild: remove -fvisibility=hidden from cflags
This fixes an issue when compiling wireguard as a module for ARM kernels in
THUMB2 mode without the JUMP11 workaround.
* noise: do not assign initiation time in if condition
Style fix.
* device: avoid circular netns references
Fixes a circular reference issue with network namespaces.
* netns: workaround bad 5.2.y backport
This works around a back backport in the 5.2.y series.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
"[[" is a bash extension for test. As the ash-implementation is not
fully compatible we drop its usage.
This follows up 3519bf4976
As a result, we also need to move the and/or out of the test brackets.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[squash from two patches, adjust commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- drop patches (applied upstream):
* 010-backport-change-address-logging.patch
* 020-backport-ed25519-support.patch
* 021-backport-chacha20-poly1305-support.patch
- backport patches:
* 010-backport-disable-toom-and-karatsuba.patch:
reduce dropbear binary size (about ~8Kb).
- refresh patches.
- don't bother anymore with following config options
because they are disabled in upstream too:
* DROPBEAR_3DES
* DROPBEAR_ENABLE_CBC_MODE
* DROPBEAR_SHA1_96_HMAC
- explicitly disable DO_MOTD as it was before commit a1099ed:
upstream has (accidentally) switched it to 0 in release 2019.77,
but reverted back in release 2020.79.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Ubus patch as it seems have been broken by some rebase in the past as
the location of line that adds ubus object file was in condition for
CONFIG_MACSEC. That condition was adding object files that are not
touched by ubus patch. This means ubus.o does not have to be included in
that case. When it has to be and when build fails is when CONFIG_AP is
set. All files included in wpa_supplicant that are touched by this patch
are in this condition. This means that this is for sure the original
place for it.
Signed-off-by: Karel Kočí <karel.koci@nic.cz>
Pass a default --up and --down executable to each started OpenVPN instance
which triggers /etc/hotplug.d/openvpn/ scripts whenever an instance
goes up or down.
User-configured up and down scripts are invoked by the default shipped
01-user hotplug handler to ensure that existing setups continue to work
as before.
As a consequence of this change, the up, down and script_security OpenVPN
options are removed from the option file, since we're always passing them
via the command line, they do not need to get included into the generated
configuration.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
[reword commit message, move hotplug executable to /usr/libexec]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Bringing up of station vlan fails if the optional mac entry isn't set.
The default mac "00:00:00:00:00:00", which should match all stations,
is mistakenly set to the non used variable "isolate". This results in
a wrong formatted .psk file which has to be "vlan_id mac key".
fixes: 5aa2ddd0: hostapd: add support for wifi-station and wifi-vlan sections
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
IPKG_INSTROOT is only set under image builder and we won't be running
this script at build time either, so remove the reference before it gets
cargo-culted into other scripts.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
Bump to latest Git and refresh all patches in order to get fix for "UPnP
SUBSCRIBE misbehavior in hostapd WPS AP" (CVE-2020-12695).
General security vulnerability in the way the callback URLs in the UPnP
SUBSCRIBE command are used were reported (VU#339275, CVE-2020-12695).
Some of the described issues may be applicable to the use of UPnP in WPS
AP mode functionality for supporting external registrars.
Ref: https://w1.fi/security/2020-1/
Signed-off-by: Petr Štetiar <ynezz@true.cz>
d13290b Fix advertised IPv6 addresses
Don't just serve link-local addresses via mdns, offer all.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
When bringing up wifi the first time after boot, these warnings appear:
netifd: radio0 (1370): rm: can't remove '/var/run/hostapd-wlan0.psk': No such file or directory
netifd: radio0 (1370): rm: can't remove '/var/run/hostapd-wlan0.vlan': No such file or directory
Silence them by adding the "-f" option to rm.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
This patch adds support for 2 new uci sections.
config wifi-vlan
# iface is optional. if it is not defined the vlan will apply
# to all interfaces
option iface default_radio0
option name guest
option vid 100
option network guest
config wifi-station
# iface is optional. if it is not defined the station will apply
# to all interfaces
option iface default_radio0
# mac is optional. if it is not defined it will be a catch all
# for any sta using this key
option mac '00:11:22:33:44:55'
# vid is optional. if it is not defined, the sta will be part of
# the primary iface.
option vid 100
option key testtest
With this patch applied it is possible to use multiple PSKs on a single BSS.
Signed-off-by: John Crispin <john@phrozen.org>
ddd57c2 pppd: Add lcp-echo-adaptive option
c319558 pppd: Handle SIGINT and SIGTERM during interrupted syscalls (#148)
0bc11fb Added missing options to manual pages. (#149)
b1fcf16 Merge branch 'monotonic-time' of https://github.com/themiron/ppp
c78e312 pppd: linux: use monotonic time if possible
Remove patch 121-debian_adaptive_lcp_echo as patch is upstream accepted
Remove patch 206-compensate_time_change.patch as timewrap issues are
solved by a patch making use of monotonic time
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
disable_vht parameter needs to be set when using wpa_supplicant NOHT/HT* modes.
Signed-off-by: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net>
Commit 472fd98c5b ("hostapd: disable support for Wired Equivalent
Privacy by default") made support for WEP optional.
Expose the WEP support to LuCi or other userspace tools using the
existing interface. This way they are able to remove WEP from the
available ciphers if hostapd is built without WEP support.
Signed-off-by: David Bauer <mail@david-bauer.net>
Bring back 802.11s mesh features to the level previously available
before the recent hostapd version bump. This is mostly to support use
of 802.11s on DFS channels, but also making mesh forwarding
configurable which is crucial for use of 802.11s MAC with other routing
protocols, such as batman-adv, on top.
While at it, fix new compiler warning by adapting 700-wifi-reload.patch
to upstream changes, now building without any warnings again.
Fixes: 0a3ec87a66 ("hostapd: update to latest Git hostap_2_9-1238-gdd2daf0848ed")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This version has the various slew of bug fixes and compat fixes and
such, but the most interesting thing from an OpenWRT perspective is that
WireGuard now plays nicely with cake and fq_codel. I'll be very
interested to hear from OpenWRT users whether this makes a measurable
difference. Usual set of full changes follows.
This release aligns with the changes I sent to DaveM for 5.7-rc7 and were
pushed to net.git about 45 minutes ago.
* qemu: use newer iproute2 for gcc-10
* qemu: add -fcommon for compiling ping with gcc-10
These enable the test suite to compile with gcc-10.
* noise: read preshared key while taking lock
Matt noticed a benign data race when porting the Linux code to OpenBSD.
* queueing: preserve flow hash across packet scrubbing
* noise: separate receive counter from send counter
WireGuard now works with fq_codel, cake, and other qdiscs that make use of
skb->hash. This should significantly improve latency spikes related to
buffer bloat. Here's a before and after graph from some data Toke measured:
https://data.zx2c4.com/removal-of-buffer-bloat-in-wireguard.png
* compat: support RHEL 8 as 8.2, drop 8.1 support
* compat: support CentOS 8 explicitly
* compat: RHEL7 backported the skb hash renamings
The usual RHEL churn.
* compat: backport renamed/missing skb hash members
The new support for fq_codel and friends meant more backporting work.
* compat: ip6_dst_lookup_flow was backported to 4.14, 4.9, and 4.4
The main motivation for releasing this now: three stable kernels were released
at the same time, with a patch that necessitated updating in our compat layer.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Upstream in commit 200c7693c9a1 ("Make WEP functionality an optional
build parameter") has made WEP functionality an optional build parameter
disabled as default, because WEP should not be used for anything
anymore. As a step towards removing it completely, they moved all WEP
related functionality behind CONFIG_WEP blocks and disabled it by
default.
This functionality is subject to be completely removed in a future
release.
So follow this good security advice, deprecation notice and disable WEP
by default, but still allow custom builds with WEP support via
CONFIG_WPA_ENABLE_WEP config option till upstream removes support for
WEP completely.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Bump package to latest upstream Git HEAD which is commit dd2daf0848ed
("HE: Process HE 6 GHz band capab from associating HE STA"). Since last
update there was 1238 commits done in the upstream tree with 618 files
changed, 53399 insertions, 24928 deletions.
I didn't bothered to rebase mesh patches as the changes seems not
trivial and I don't have enough knowledge of those parts to do/test that
properly, so someone else has to forward port them, ideally upstream
them so we don't need to bother anymore. I've just deleted them for now:
004-mesh-use-setup-completion-callback-to-complete-mesh-.patch
005-mesh-update-ssid-frequency-as-pri-sec-channel-switch.patch
006-mesh-inform-kernel-driver-DFS-handler-in-userspace.patch
007-mesh-apply-channel-attributes-before-running-Mesh.patch
011-mesh-Allow-DFS-channels-to-be-selected-if-dfs-is-ena.patch
013-mesh-do-not-allow-pri-sec-channel-switch.patch
015-mesh-do-not-use-offchan-mgmt-tx-on-DFS.patch
016-mesh-fix-channel-switch-error-during-CAC.patch
018-mesh-make-forwarding-configurable.patch
Refreshed all other patches, removed upstreamed patches:
051-wpa_supplicant-fix-race-condition-in-mesh-mpm-new-pe.patch
067-0001-AP-Silently-ignore-management-frame-from-unexpected-.patch
070-driver_nl80211-fix-WMM-queue-mapping-for-regulatory-.patch
071-driver_nl80211-fix-regulatory-limits-for-wmm-cwmin-c.patch
090-wolfssl-fix-crypto_bignum_sum.patch
091-0001-wolfssl-Fix-compiler-warnings-on-size_t-printf-forma.patch
091-0002-wolfssl-Fix-crypto_bignum_rand-implementation.patch
091-0003-wolfssl-Do-not-hardcode-include-directory-in-wpa_sup.patch
800-usleep.patch
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065/NBG6817; ipq40xx/MAP-AC2200]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
crypto_bignum_rand() use needless time-consuming filtering
which resulted in SAE no longer connecting within time limits.
Import fixes from hostap upstream to fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hotplug scripts are sourced so the #!/bin/sh is superfluous/deceptive.
Re-arrange script to only source 'procd' if we get to the stage of
needing to signal the process, reduce hotplug processing load a little.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
add option to set management IP pattern
also add missing 'unconfigure system hostname'
for example pattern '!192.168.1.1' makes it possible that
WAN IP is selected instead of LAN IP
Signed-off-by: Daniel A. Maierhofer <git@damadmai.at>
[grammar and spelling fixes in commit message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Samba 3.6 is completely unsupported, in addition to having tons of patches
It also causes kernel panics on some platforms when sendfile is enabled.
Example:
https://github.com/gnubee-git/GnuBee_Docs/issues/45
I have reproduced on ramips as well as mvebu in the past.
Samba 4 is an alternative available in the packages repo.
cifsd is a lightweight alternative available in the packages repo. It is
also a faster alternative to both Samba versions (lower CPU usage). It
was renamed to ksmbd.
To summarize, here are the alternatives:
- ksmbd + luci-app-cifsd
- samba4 + luci-app-samba4
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[drop samba36-server from GEMINI_NAS_PACKAGES, ksmbd rename + summary]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* compat: timeconst.h is a generated artifact
Before we were trying to check for timeconst.h by looking in the kernel
source directory. This isn't quite correct on configurations in which
the object directory is separate from the kernel source directory, for
example when using O="elsewhere" as a make option when building the
kernel. The correct fix is to use $(CURDIR), which should point to
where we want.
* compat: use bash instead of bc for HZ-->USEC calculation
This should make packaging somewhat easier, as bash is generally already
available (at least for dkms), whereas bc isn't provided by distros by
default in their build meta packages.
* socket: remove errant restriction on looping to self
It's already possible to create two different interfaces and loop
packets between them. This has always been possible with tunnels in the
kernel, and isn't specific to wireguard. Therefore, the networking stack
already needs to deal with that. At the very least, the packet winds up
exceeding the MTU and is discarded at that point. So, since this is
already something that happens, there's no need to forbid the not very
exceptional case of routing a packet back to the same interface; this
loop is no different than others, and we shouldn't special case it, but
rather rely on generic handling of loops in general. This also makes it
easier to do interesting things with wireguard such as onion routing.
At the same time, we add a selftest for this, ensuring that both onion
routing works and infinite routing loops do not crash the kernel. We
also add a test case for wireguard interfaces nesting packets and
sending traffic between each other, as well as the loop in this case
too. We make sure to send some throughput-heavy traffic for this use
case, to stress out any possible recursion issues with the locks around
workqueues.
* send: cond_resched() when processing tx ringbuffers
Users with pathological hardware reported CPU stalls on CONFIG_
PREEMPT_VOLUNTARY=y, because the ringbuffers would stay full, meaning
these workers would never terminate. That turned out not to be okay on
systems without forced preemption. This commit adds a cond_resched() to
the bottom of each loop iteration, so that these workers don't hog the
core. We don't do this on encryption/decryption because the compat
module here uses simd_relax, which already includes a call to schedule
in preempt_enable.
* selftests: initalize ipv6 members to NULL to squelch clang warning
This fixes a worthless warning from clang.
* send/receive: use explicit unlikely branch instead of implicit coalescing
Some code readibility cleanups.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* compat: support latest suse 15.1 and 15.2
* compat: support RHEL 7.8's faulty siphash backport
* compat: error out if bc is missing
* compat: backport hsiphash_1u32 for tests
We now have improved support for RHEL 7.8, SUSE 15.[12], and Ubuntu 16.04.
* compat: include sch_generic.h header for skb_reset_tc
A fix for a compiler error on kernels with weird configs.
* compat: import latest fixes for ptr_ring
* compat: don't assume READ_ONCE barriers on old kernels
* compat: kvmalloc_array is not required anyway
ptr_ring.h from upstream was imported, with compat modifications, to our
compat layer, to receive the latest fixes.
* compat: prefix icmp[v6]_ndo_send with __compat
Some distros that backported icmp[v6]_ndo_send still try to build the compat
module in some corner case circumstances, resulting in errors. Work around
this with the usual __compat games.
* compat: ip6_dst_lookup_flow was backported to 3.16.83
* compat: ip6_dst_lookup_flow was backported to 4.19.119
Greg and Ben backported the ip6_dst_lookup_flow patches to stable kernels,
causing breaking in our compat module, which these changes fix.
* git: add gitattributes so tarball doesn't have gitignore files
Distros won't need to clean this up manually now.
* crypto: do not export symbols
These don't do anything and only increased file size.
* queueing: cleanup ptr_ring in error path of packet_queue_init
Sultan Alsawaf reported a memory leak on an error path.
* main: mark as in-tree
Now that we're upstream, there's no need to set the taint flag.
* receive: use tunnel helpers for decapsulating ECN markings
ECN markings are now decapsulated using RFC6040 instead of the old RFC3168.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Init script checks for an already active DHCP server on the interface
and if such DHCP server is found, then it logs "refusing to start DHCP"
message, starts dnsmasq without DHCP service unless `option force 1` is
set and caches the DHCP server check result.
Each consecutive service start then uses this cached DHCP server check
result, but doesn't provide log feedback about disabled DHCP service
anymore.
So this patch ensures, that the log message about disabled DHCP service
on particular interface is always provided.
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Backport patch from hostapd.git master that fixes copy/paste error in
crypto_bignum_sub() in crypto_wolfssl.c.
This missing fix was discovered while testing SAE over a mesh interface.
With this fix applied and wolfssl >3.14.4 mesh+SAE works fine with
wpad-mesh-wolfssl.
Cc: Sean Parkinson <sean@wolfssl.com>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
f4d759b dhcp.c: further improve validation
Further improve input validation for CVE-2020-11752
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
cdac046 dns.c: fix input validation fix
Due to a slight foobar typo, failing to de-reference a pointer, previous
fix not quite as complete as it should have been.
Improve CVE-2020-11750 fix
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This is primarily a maintenance release with bugfixes and improvements.
This release also fixes a security issue (CVE-2020-11810) which allows
disrupting service of a freshly connected client that has not yet
negotiated session keys. The vulnerability cannot be used to
inject or steal VPN traffic.
Release announcement:
https://openvpn.net/community-downloads/#heading-13812
Full list of changes:
https://community.openvpn.net/openvpn/wiki/ChangesInOpenvpn24#OpenVPN2.4.9
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
CONFIG_WRITE functionality is not used and could be removed.
Looks helpful for devices with small flash because wpad is also affected.
Little testing shows that about 6 KB could be saved.
Signed-off-by: Kirill Lukonin <klukonin@gmail.com>
Use upstream latest git HEAD as it allows to remove the patches
700-radius-Prevent-buffer-overflow-in-rc_mksid,
701-pppd-Fix-bounds-check-in-EAP-code and
702-pppd-Ignore-received-EAP-messages-when-not-doing-EAP and
take in other fixes.
41a7323 pppd: Fixed spelling 'unkown' => 'unknown' (#141)
6b014be pppd: Print version information to stdout instead of stderr (#133)
cba2736 pppd: Add RFC1990 (Multilink) to the See Also section of the man page
f2f9554 pppd: Add mppe.h to the list of headers to install if MPPE is defined
ae54fcf pppd: Obfuscate password argument string
8d45443 pppd: Ignore received EAP messages when not doing EAP
8d7970b pppd: Fix bounds check in EAP code
858976b radius: Prevent buffer overflow in rc_mksid()
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Bump to 2.81rc5 and re-work ipset-remove-old-kernel-support.
More runtime kernel version checking is done in 2.81rc5 in various parts
of the code, so expand the ipset patch' scope to inlude those new areas
and rename to something a bit more generic.:wq
Upstream changes from rc4
532246f Tweak to DNSSEC logging.
8caf3d7 Fix rare problem allocating frec for DNSSEC.
d162bee Allow overriding of ubus service name.
b43585c Fix nameserver list in auth mode.
3f60ecd Fixed resource leak on ubus_init failure.
0506a5e Handle old kernels that don't do NETLINK_NO_ENOBUFS.
e7ee1aa Extend stop-dns-rebind to reject IPv6 LL and ULA addresses. We also reject the loopback address if rebind-localhost-ok is NOT set.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
201e359 Handle early exit when addrstring isn't set
fa4c464 Improve address logging on early exit messages (#83)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
It seemed very confusing when trying to select the different variants of
hostapd which are somewhat scattered about under the menu 'Network'.
Moving all hostapd variants under a common submenu helps avoid
confusion.
Inspired-by: Kevin Mahoney <kevin.mahoney@zenotec.net>
[Fixup badly formatted patch, change menu name]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
ab7a39a umdns: fix unused error
45c4953 dns: explicitly endian-convert all fields in header and question
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
gcc 8 & 9 appear to be more picky with regards access alignment to
packed structures, leading to this warning in dns.c:
dns.c:261:2: error: converting a packed ‘struct dns_question’ pointer
(alignment 1) to a ‘uint16_t’ {aka ‘short unsigned int’} pointer
(alignment 2) may result in an unaligned pointer value
[-Werror=address-of-packed-member]
261 | uint16_t *swap = (uint16_t *) q;
Work around what I think is a false positive by turning the warning off.
Not ideal, but not quite as not ideal as build failure.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Recent backports to 5.5 and 5.4 broke our compat layer. This release is
to keep things running with the latest upstream stable kernels.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* queueing: backport skb_reset_redirect change from 5.6
* version: bump
This release has only one slight change, to put it closer to the 5.6
codebase, but its main purpose is to bump us to a 1.0.y version number.
Now that WireGuard 1.0.0 has been released for Linux 5.6 [1], we can put
the same number on the backport compat codebase.
When OpenWRT bumps to Linux 5.6, we'll be able to drop this package
entirely, which I look forward to seeing.
[1] https://lists.zx2c4.com/pipermail/wireguard/2020-March/005206.html
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
If the abridged flag is set to 1 the APs that are listed in the BSS
Transition Candidate List are prioritized. If the bit is not set, the
APs have the same prioritization as the APs that are not in the list.
If you want to steer a client, you should set the flag!
The flag can be set by adding {...,'abridged': true,...} to the normal
ubus call.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Subscribe to beacon reports through ubus.
Can be used for hearing map and client steering purposes.
First enable rrm:
ubus call hostapd.wlan0 bss_mgmt_enable '{"beacon_report":True}'
Subscribe to the hostapd notifications via ubus.
Request beacon report:
ubus call hostapd.wlan0 rrm_beacon_req
'{"addr":"00:xx:xx:xx:xx:xx", "op_class":0, "channel":1,
"duration":1,"mode":2,"bssid":"ff:ff:ff:ff:ff:ff", "ssid":""}'
Signed-off-by: Nick Hainke <vincent@systemli.org>
[rework identation]
Signed-off-by: David Bauer <mail@david-bauer.net>
Fix the test for an enabled sysntp initscript in dnsmasq.init, and get
rid of "test -o" while at it.
Issue reproduced on openwrt-19.07 with the help of pool.ntp.br and an
RTC-less ath79 router. dnssec-no-timecheck would be clearly missing
from /var/etc/dnsmasq.conf.* while the router was still a few days in
the past due to non-working DNSSEC + DNS-based NTP server config.
The fix was tested with the router in the "DNSSEC broken state": it
properly started dnsmasq in dnssec-no-timecheck mode, and eventually ntp
was able to resolve the server name to an IP address, and set the system
time. DNSSEC was then enabled by SIGINT through the ntp hotplug hook,
as expected.
A missing system.ntp.enabled UCI node is required for the bug to show
up. The reasons for why it would be missing in the first place were not
investigated.
Signed-off-by: Henrique de Moraes Holschuh <henrique@nic.br>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
Refer to shellcheck SC2166. There are just too many caveats that are
shell-dependent on test -a and test -o to use them.
Signed-off-by: Henrique de Moraes Holschuh <henrique@nic.br>
Add option 'scriptarp' to uci dnsmasq config to enable --script-arp functions.
The default setting is false, meaning any scripts in `/etc/hotplug.d/neigh` intended
to be triggered by `/usr/lib/dnsmasq/dhcp-script.sh` will fail to execute.
Also enable --script-arp if has_handlers returns true.
Signed-off-by: Jordan Sokolic <oofnik@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
WireGuard had a brief professional security audit. The auditors didn't find
any vulnerabilities, but they did suggest one defense-in-depth suggestion to
protect against potential API misuse down the road, mentioned below. This
compat snapshot corresponds with the patches I just pushed to Dave for
5.6-rc7.
* curve25519-x86_64: avoid use of r12
This buys us 100 extra cycles, which isn't much, but it winds up being even
faster on PaX kernels, which use r12 as a RAP register.
* wireguard: queueing: account for skb->protocol==0
This is the defense-in-depth change. We deal with skb->protocol==0 just fine,
but the advice to deal explicitly with it seems like a good idea.
* receive: remove dead code from default packet type case
A default case of a particular switch statement should never be hit, so
instead of printing a pretty debug message there, we full-on WARN(), so that
we get bug reports.
* noise: error out precomputed DH during handshake rather than config
All peer keys will now be addable, even if they're low order. However, no
handshake messages will be produced successfully. This is a more consistent
behavior with other low order keys, where the handshake just won't complete if
they're being used anywhere.
* send: use normaler alignment formula from upstream
We're trying to keep a minimal delta with upstream for the compat backport.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
When introducing ubus reload support, ubus initialization was moved
to the service level instead of being carried out when adding a BSS
configuration. While this works when using wpa_supplicant in that way,
it breaks the ability to run wpa_supplicant on the command line, eg.
for debugging purposes.
Fix that by re-introducing ubus context intialization when adding
configuration.
Reported-by: @PolynomialDivision https://github.com/openwrt/openwrt/pull/2417
Fixes: 60fb4c92b6 ("hostapd: add ubus reload")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
6594c6b ubus: use dhcpv6 ia assignment flag
a90cc2e dhcpv6-ia: avoid setting lifetime to infinite for static assignments
bb07fa4 dhcpv4: avoid setting lifetime to infinite for static assignments
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Bump to latest release candidate and drop 2 local patches that have been
upstreamed.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Bump to dnsmasq 2.81rc2. In the process discovered several compiler
warnings one with a logical error.
2 relevant patches sent upstream, added as 2 local patches for OpenWrt
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
1st release candidate for v2.81 after 18 months.
Refresh patches & remove all upstreamed leaving:
110-ipset-remove-old-kernel-support.patch
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This activates PIE ASLR support by default when the regular option is
selected.
Size increase on imx6:
112681 ppp_2.4.8-2_arm_cortex-a9_neon.ipk
121879 ppp_2.4.8-2_arm_cortex-a9_neon.ipk
= 9198 diff
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This reverts commit 215598fd03 since it
didn't contain a reference to the CVE it addresses. The next commit
will re-add the commit including a CVE reference in its commit message.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add a radio_config_id property. If the radio config changes return an error
upon receiving the reconf call.
Signed-off-by: John Crispin <john@phrozen.org>
c888e17e06 ("hostapd: manage instances via procd instead of pidfile")
added procd support for managing hostapd and wpa_supplicant daemons
but at the same time limited wiphy names to 'phy*'.
This brings back initial behaviour (introduced in 60fb4c92b6 ("hostapd:
add ubus reload") and makes procd manage daemons for any wiphy device
found in '/sys/class/ieee80211'.
CC: Felix Fietkau <nbd@nbd.name>
CC: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
8d45443bb5c9 pppd: Ignore received EAP messages when not doing EAP
8d7970b8f3db pppd: Fix bounds check in EAP code
858976b1fc31 radius: Prevent buffer overflow in rc_mksid()
Signed-off-by: Petr Štetiar <ynezz@true.cz>
A file, package/network/services/dnsmasq/files/50-dnsmasq-migrate-resolv-conf-auto.sh,
was added in commit 6a28552120, but it
does not exit in a way that tells the uci-defaults mechanism that it
succeeded, and so it is not cleaned up after running successfully. Add
an exit 0 to the end to correct that.
Signed-off-by: Russell Senior <russell@personaltelco.net>
* send: cleanup skb padding calculation
* socket: remove useless synchronize_net
Sorry for the back-to-back releases. This fixes a regression spotted by Eric
Dumazet.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
The $(space) definition in the hostapd Makefile ceased to work with
GNU Make 4.3 and later, leading to syntax errors in the generated
Kconfig files.
Drop the superfluous redefinition and reuse the working $(space)
declaration from rules.mk to fix this issue.
Fixes: GH#2713
Ref: https://github.com/openwrt/openwrt/pull/2713#issuecomment-583722469
Reported-by: Karel Kočí <cynerd@email.cz>
Suggested-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Shaleen Jain <shaleen@jain.sh>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* compat: support building for RHEL-8.2
* compat: remove RHEL-7.6 workaround
Bleeding edge RHEL users should be content now (which includes the actual
RedHat employees I've been talking to about getting this into the RHEL kernel
itself). Also, we remove old hacks for versions we no longer support anyway.
* allowedips: remove previously added list item when OOM fail
* noise: reject peers with low order public keys
With this now being upstream, we benefit from increased fuzzing coverage of
the code, uncovering these two bugs.
* netns: ensure non-addition of peers with failed precomputation
* netns: tie socket waiting to target pid
An added test to our test suite for the above and a small fix for high-load CI
scenarios.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Fixes handling CSA when using AP+STA or AP+Mesh
This change was accidentally dropped in commit 167028b75
("hostapd: Update to version 2.9 (2019-08-08)")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Without this change, wpa-cli features depend on which wpad build variant was
used to build the wpa-cli package
Signed-off-by: Felix Fietkau <nbd@nbd.name>
"[[" is a bash extension for test. As the ash-implementation is not
fully compatible we drop its usage.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[remove shebang, slightly facelift commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* Makefile: strip prefixed v from version.h
This fixes a mistake in dmesg output and when parsing the sysfs entry in the
filesystem.
* device: skb_list_walk_safe moved upstream
This is a 5.6 change, which we won't support here, but it does make the code
cleaner, so we make this change to keep things in sync.
* curve25519: x86_64: replace with formally verified implementation
This comes from INRIA's HACL*/Vale. It implements the same algorithm and
implementation strategy as the code it replaces, only this code has been
formally verified, sans the base point multiplication, which uses code
similar to prior, only it uses the formally verified field arithmetic
alongside reproducable ladder generation steps. This doesn't have a
pure-bmi2 version, which means haswell no longer benefits, but the
increased (doubled) code complexity is not worth it for a single
generation of chips that's already old.
Performance-wise, this is around 1% slower on older microarchitectures,
and slightly faster on newer microarchitectures, mainly 10nm ones or
backports of 10nm to 14nm. This implementation is "everest" below:
Xeon E5-2680 v4 (Broadwell)
armfazh: 133340 cycles per call
everest: 133436 cycles per call
Xeon Gold 5120 (Sky Lake Server)
armfazh: 112636 cycles per call
everest: 113906 cycles per call
Core i5-6300U (Sky Lake Client)
armfazh: 116810 cycles per call
everest: 117916 cycles per call
Core i7-7600U (Kaby Lake)
armfazh: 119523 cycles per call
everest: 119040 cycles per call
Core i7-8750H (Coffee Lake)
armfazh: 113914 cycles per call
everest: 113650 cycles per call
Core i9-9880H (Coffee Lake Refresh)
armfazh: 112616 cycles per call
everest: 114082 cycles per call
Core i3-8121U (Cannon Lake)
armfazh: 113202 cycles per call
everest: 111382 cycles per call
Core i7-8265U (Whiskey Lake)
armfazh: 127307 cycles per call
everest: 127697 cycles per call
Core i7-8550U (Kaby Lake Refresh)
armfazh: 127522 cycles per call
everest: 127083 cycles per call
Xeon Platinum 8275CL (Cascade Lake)
armfazh: 114380 cycles per call
everest: 114656 cycles per call
Achieving these kind of results with formally verified code is quite
remarkable, especialy considering that performance is favorable for
newer chips.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
hostapd sets minimum values for CWmin/CWmax/AIFS and maximum for TXOP.
The code for applying those values had a few bugs leading to bogus values,
which caused significant latency and packet loss.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
6db312a dhcpv6-ia: use dhcp leasetime to set preferred/valid statefull lifetimes
2520c48 dhcpv6-ia: introduce DHCPv6 pd and ia assignments flags
b413d8a dhcpv6-ia: cleanup prefix delegation routes
b0902af dhcpv6-ia: remove passing interface as parameter to apply_lease
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Currently, it is very cumbersome for a user to connect to a WPA-Enterprise
based network securely because the RADIUS server's CA certificate must first be
extracted from the EAPOL handshake using tcpdump or other methods before it can
be pinned using the ca_cert(2) fields. To make this process easier and more
secure (combined with changes in openwrt/openwrt#2654), this commit adds
support for validating against the built-in CA bundle when the ca-bundle
package is installed. Related LuCI changes in openwrt/luci#3513.
Signed-off-by: David Lam <david@thedavid.net>
[bump PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
With this change it is now possible to switch off single instances of
the uhttpd config. Until now it was only possible to switch all
instances of uhttpd on or off.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Rekey GTK on STA disassociate
Signed-off-by: Kyle Copperfield <kmcopper@danwin1210.me>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Allows dtim_period to be configurable, the default is from hostapd.
Adds additional regulatory tunables for power constraint and spectrum
managment.
Signed-off-by: Kyle Copperfield <kmcopper@danwin1210.me>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Failsafe code of dropbear should be in the dropbear package not the
base-files package.
Signed-off-by: Kyle Copperfield <kmcopper@danwin1210.me>
The wpa_supplicant supports certificate subject validation via the
subject match(2) and altsubject_match(2) fields. domain_match(2) and
domain_suffix_match(2) fields are also supported for advanced matches.
This validation is especially important when connecting to access
points that use PAP as the Phase 2 authentication type. Without proper
validation, the user's password can be transmitted to a rogue access
point in plaintext without the user's knowledge. Most organizations
already require these attributes to be included to ensure that the
connection from the STA and the AP is secure. Includes LuCI changes via
openwrt/luci#3444.
From the documentation:
subject_match - Constraint for server certificate subject. This substring
is matched against the subject of the authentication server certificate.
If this string is set, the server sertificate is only accepted if it
contains this string in the subject. The subject string is in following
format: /C=US/ST=CA/L=San Francisco/CN=Test AS/emailAddress=as
.example.com
subject_match2 - Constraint for server certificate subject. This field is
like subject_match, but used for phase 2 (inside EAP-TTLS/PEAP/FAST
tunnel) authentication.
altsubject_match - Constraint for server certificate alt. subject.
Semicolon separated string of entries to be matched against the
alternative subject name of the authentication server certificate. If
this string is set, the server sertificate is only accepted if it
contains one of the entries in an alternative subject name extension.
altSubjectName string is in following format: TYPE:VALUE Example:
EMAIL:server@example.com Example:
DNS:server.example.com;DNS:server2.example.com Following types are
supported: EMAIL, DNS, URI
altsubject_match2 - Constraint for server certificate alt. subject. This
field is like altsubject_match, but used for phase 2 (inside
EAP-TTLS/PEAP/FAST tunnel) authentication.
domain_match - Constraint for server domain name. If set, this FQDN is
used as a full match requirement for the
server certificate in SubjectAltName dNSName element(s). If a
matching dNSName is found, this constraint is met. If no dNSName
values are present, this constraint is matched against SubjectName CN
using same full match comparison. This behavior is similar to
domain_suffix_match, but has the requirement of a full match, i.e.,
no subdomains or wildcard matches are allowed. Case-insensitive
comparison is used, so "Example.com" matches "example.com", but would
not match "test.Example.com". More than one match string can be
provided by using semicolons to
separate the strings (e.g., example.org;example.com). When multiple
strings are specified, a match with any one of the values is considered
a sufficient match for the certificate, i.e., the conditions are ORed
together.
domain_match2 - Constraint for server domain name. This field is like
domain_match, but used for phase 2 (inside EAP-TTLS/PEAP/FAST tunnel)
authentication.
domain_suffix_match - Constraint for server domain name. If set, this
FQDN is used as a suffix match requirement for the AAA server
certificate in SubjectAltName dNSName element(s). If a matching dNSName
is found, this constraint is met. If no dNSName values are present,
this constraint is matched against SubjectName CN using same suffix
match comparison. Suffix match here means that the host/domain name is
compared one label at a time starting from the top-level domain and all
the labels in domain_suffix_match shall be included in the certificate.
The certificate may include additional sub-level labels in addition to
the required labels. More than one match string can be provided by using
semicolons to separate the strings (e.g., example.org;example.com).
When multiple strings are specified, a match with any one of the values
is considered a sufficient match for the certificate, i.e., the
conditions are ORed together. For example,
domain_suffix_match=example.com would match test.example.com but would
not match test-example.com. This field is like domain_match, but used
for phase 2 (inside EAP-TTLS/PEAP/FAST tunnel) authentication.
domain_suffix_match2 - Constraint for server domain name. This field is
like domain_suffix_match, but used for phase 2 (inside
EAP-TTLS/PEAP/FAST tunnel) authentication.
Signed-off-by: David Lam <david@thedavid.net>
This activates PIE ASLR support by default when the regular option is
selected.
Size increase on x86/64:
odhcpd-ipv6only Installed-Size: 36821 -> 38216
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This activates PIE ASLR support by default when the regular option is
selected.
This increases the binary size by 39% uncompressed and 21% compressed
on MIPS BE.
old:
33,189 /usr/sbin/uhttpd
23,016 uhttpd_2019-08-17-6b03f960-4_mips_24kc.ipk
new:
46,212 /usr/sbin/uhttpd
27,979 uhttpd_2019-08-17-6b03f960-4_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Petr Štetiar <ynezz@true.cz>
This activates PIE ASLR support by default when the regular option is
selected.
This increases the binary size by 26% uncompressed and 16% compressed
on MIPS BE.
old:
460,933 /usr/sbin/wpad
283,891 wpad-basic_2019-08-08-ca8c2bd2-1_mips_24kc.ipk
new:
584,508 /usr/sbin/wpad
330,281 wpad-basic_2019-08-08-ca8c2bd2-1_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Petr Štetiar <ynezz@true.cz>
This activates PIE ASLR support by default when the regular option is
selected.
This increases the binary size by 18% uncompressed and 17% compressed
on MIPS BE.
old:
164,261 /usr/sbin/dropbear
85,648 dropbear_2019.78-2_mips_24kc.ipk
new:
194,492 /usr/sbin/dropbear
100,309 dropbear_2019.78-2_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Petr Štetiar <ynezz@true.cz>
This activates PIE ASLR support by default when the regular option is
selected.
This increases the binary size by 37% uncompressed and 18% compressed
on MIPS BE.
old:
146,933 /usr/sbin/dnsmasq
101,837 dnsmasq_2.80-14_mips_24kc.ipk
new:
202,020 /usr/sbin/dnsmasq
120,577 dnsmasq_2.80-14_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Petr Štetiar <ynezz@true.cz>
* socket: mark skbs as not on list when receiving via gro
Certain drivers will pass gro skbs to udp, at which point the udp driver
simply iterates through them and passes them off to encap_rcv, which is
where we pick up. At the moment, we're not attempting to coalesce these
into bundles, but we also don't want to wind up having cascaded lists of
skbs treated separately. The right behavior here, then, is to just mark
each incoming one as not on a list. This can be seen in practice, for
example, with Qualcomm's rmnet_perf driver. This lead to crashes on
OnePlus devices and possibly other Qualcomm 4.14 devices. But I fear
that it could lead to issues on other drivers on weird OpenWRT routers.
This commit is upstream in net-next as:
https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=736775d06bac60d7a353e405398b48b2bd8b1e54
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
When running sysupgrade from an existing configuration, UCI option
dhcp.@dnsmasq[0].resolvfile needs to be modified in case it has not
been changed from it's original value.
Accomplish that using a uci-defaults script.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Without this commit, ft_psk_generate_local is enabled for non-PSK
networks by default. This breaks 802.11r for EAP networks.
Disable ft_psk_generate_local by default for non-PSK networks resolves
this misbehavior.
Reported-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Previous commit should have bumped PKG_RELEASE, but git add was
forgotten... Add it now.
Fixes: cd48d8d342 ("dnsmasq: switch to /tmp/resolv.conf.d/resolv.conf.auto")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Mount-bind directory instead of resolv.conf.auto file in jail to
avoid problems when the file is deleted/replaced.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is a backport from the dnsmasq master which should fix a bug which
could cause a crash in dnsmasq.
I saw the following crashes in my log:
[522413.117215] do_page_fault(): sending SIGSEGV to dnsmasq for invalid read access from 2a001450
[522413.124464] epc = 004197f1 in dnsmasq[400000+23000]
[522413.129459] ra = 004197ef in dnsmasq[400000+23000]
This is happening in blockdata_write() when block->next is
dereferenced, but I am not sure if this is related to this problem or if
this is a different problem. I am unable to reproduce this problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add call to fclose for file pointer fp in function t_openpw.
The resource leak could happen during an error handling.
Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
78cd384 Update README and patchlevel.h for 2.4.8 release
5d03403 pppd: Avoid use of strnlen (and strlen) in vslprintf
a1e950a pppd: Fix IPv6 default route code for Solaris
ca5e61b plugins/rp-pppoe: Make tag parsing loop condition more accurate
c10c3c7 pppd: Make sure word read from options file is null-terminated
b311e98 pppd: Limit memory accessed by string formats with max length specified
3ea9de9 pppd: Eliminate some more compiler warnings
57edb1a pppd: Include time.h header before using time_t
09f695f pppd: Don't free static string
03104ba pppd.h: Add missing headers
388597e pppd: Add defaultroute6 and related options
66ce4ba pppd: Avoid declarations within statements in main.c
5637180 pppd: Fix `ifname` option in case of multilink (#105)
d00f8a0 pppd: Fix variable reference syntax in Makefile.linux
b6b4d28 pppd: Check tdb pointer before closing
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
If CONFIG_DROPBEAR_ZLIB is set, building fails at the packaging stage
due to an undeclared dependency on libz.so.1.
As is already done for the main dropbear package, conditionally add a
dependency on zlib.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
As announced on the mailing list, WireGuard will be in Linux 5.6. As a
result, the wg(8) tool, used by OpenWRT in the same manner as ip(8), is
moving to its own wireguard-tools repo. Meanwhile, the out-of-tree
kernel module for kernels 3.10 - 5.5 moved to its own wireguard-linux-
compat repo. Yesterday, releases were cut out of these repos, so this
commit bumps packages to match. Since wg(8) and the compat kernel module
are versioned and released separately, we create a wireguard-tools
Makefile to contain the source for the new tools repo. Later, when
OpenWRT moves permanently to Linux 5.6, we'll drop the original module
package, leaving only the tools. So this commit shuffles the build
definition around a bit but is basically the same idea as before.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
edad0d6 version: bump snapshot
0e38a3c compat: ipv6_dst_lookup_flow was backported to 5.3 and 5.4
2e52c41 wg-quick: linux: use already configured addresses instead of in-memory
3721521 tools: adjust wg.8 syntax for consistency in COMMANDS section
21a1498 wg-quick: linux: try both iptables(8) and nft(8) on teardown
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
1ec6ece version: bump snapshot
e13de91 main: remove unused include <linux/version.h>
72eb17c wg-quick: linux: support older nft(8)
1d8e978 global: fix up spelling
e02713e wg-quick: linux: add support for nft and prefer it
b4e3a83 compat: support building for RHEL-8.1 instead of RHEL-8.0
f29e3ac socket: convert to ipv6_dst_lookup_flow for 5.5
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Before commit 60fb4c92b6 ("hostapd: add ubus reload") netifd was
tracking hostapd/wpa_supplicant and restarting wifi in case of a
process crash. Restore this behaviour by tracking the PIDs of
hostapd and wpa_supplicant.
Also make sure hostapd and/or wpa_supplicant have been started before
emmitting ubus calls to them using ubus wait_for.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allows graceful restart of crashing hostapd/wpa_supplicant instances
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: attempt to launch only present services]
This enables the CTRL_IFACE_MIB symbol for wpad-full and hostapd-full.
If it is not enabled, statistic outputs such as "hostapd_cli all_sta"
are empty.
Signed-off-by: David Bauer <mail@david-bauer.net>
* wg-quick: linux: suppress error when finding unused table
This fixes a spurious warning messages seen with recent versions of iproute2
and kernels.
* wg-quick: linux: ensure postdown hooks execute
* wg-quick: linux: have remove_iptables return true
* wg-quick: linux: iptables-* -w is not widely supported
Adding in iptables had some hiccups. For the record, I'm very unhappy about
having to put any firewalling code into wg-quick(8). We'll of course need to
support nftables too at some point if this continues. I'm investigating with
upstream the possibility of adding a sysctl to patch the issue that iptables
is handling now, so hopefully at somepoint down the line we'll be able to shed
this dependency once again.
* send: use kfree_skb_list
* device: prepare skb_list_walk_safe for upstreaming
* send: avoid touching skb->{next,prev} directly
Suggestions from LKML.
* ipc: make sure userspace communication frees wgdevice
Free things properly on error paths.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* messages: recalculate rekey max based on a one minute flood
* allowedips: safely dereference rcu roots
* socket: remove redundant check of new4
* allowedips: avoid double lock in selftest error case
* tools: add syncconf command
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
dnsmasq v2.80 made 'dnssec-check-unsigned' the default, thus the uci
option was rendered ineffectual: we checked unsigned zones no matter the
setting.
Disabling the checking of unsigned zones is now achieve with the
"--dnssec-check-unsigned=no" dnsmasq option.
Update init script to pass required option in the disabled case.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Add ubus interface to hostapd and wpa_supplicant to allow dynamically
reloading wiface configuration without having to restart the hostapd
process.
As a consequence, both hostapd and wpa_supplicant are now started
persistently on boot for each wifi device in the system and then
receive ubus calls adding, modifying or removing interface
configuration.
At a later stage it would be desirable to reduce the services to one
single instance managing all radios.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This decreases the binary size when PIE ASLR is activated by 8% on MIPS BE.
old:
202,020 /usr/sbin/dnsmasq
new:
185,676 /usr/sbin/dnsmasq
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This enables PMKSA and opportunistic key caching by default for
WPA2/WPA3-Personal, WPA3-Personal and OWE auth types.
Otherwise, Apple devices won't connect to the WPA3 network.
This should not degrade security, as there's no external authentication
provider.
Tested with OCEDO Koala and iPhone 7 (iOS 13.1).
Signed-off-by: David Bauer <mail@david-bauer.net>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Enables radio resource management to be reported by hostapd to clients.
Ref: https://github.com/lede-project/source/pull/1430
Co-developed-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
Signed-off-by: Kyle Copperfield <kmcopper@danwin1210.me>
Required as dependency on dropbear config headers is not tracked in
dropbear build system
Fixes FS#2275
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
8eb8443 version: bump snapshot
be09cf5 wg-quick: android: use Binder for setting DNS on Android 10
4716f85 noise: recompare stamps after taking write lock
54db197 netlink: allow preventing creation of new peers when updating
f1b87d1 netns: add test for failing 5.3 FIB changes
a3539c4 qemu: bump default version
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
0d004db Revert "pppd: Include time.h before using time_t"
e400854 pppdump: Eliminate printf format warning by using %zd
7f2f0de pppd: Refactor setjmp/longjmp with pipe pair in event wait loop
4e71317 make: Avoid using host include for cross-compiling
3202f89 pppoe: Remove the use of cdefs
d8e8d7a pppd: Remove unused rcsid variables
486f854 pppd: Fix GLIBC version test for non-glibc toolchains
b6cd558 pppd: Include time.h before using time_t
ef8ec11 radius: Fix compiler warning
f6330ec magic: Remove K&R style of arguments
347904e Add Submitting-patches.md
Remove patches 130-no_cdefs_h.patch, 131-missing_prototype_macro.patch,
132-fix_linux_includes.patch as fixed upstream
Refresh patches
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Changes since 0.0.20190702:
define conversion constants for ancient kernels
android: refactor and add incoming allow rules
enforce that unused bits of flags are zero
immediately rekey all peers after changing device private key
support running in OpenVZ environments
do not run bc on clean target
skip peers with invalid keys
account for upstream configuration maze changes
openbsd: fix alternate routing table syntax
account for android-4.9 backport of addr_gen_mode
don't fail down when using systemd-resolved
allow specifying kernel release
enforce named pipe ownership and use protected prefix
work around ubuntu breakage
support newer PaX
don't rewrite siphash when it's from compat
squelch warnings for stack limit on broken kernel configs
support rhel/centos 7.7
Signed-off-by: Brandy Krueger <krueger.brandy24@gmail.com>
hostapd will not use the getrandom() syscall and as a fallback use
/dev/random, the syscall is supported since Linux 3.17 and in the musl,
glibc and uclibc version used by OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All the content of this function is proceeded by IEEE8021X_EAPOL no code
accesses the ssid variable outside of this ifdef.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The size of the ipkgs increase a bit (between 0.7% and 1.1%):
old 2019-04-21 (2.8):
288264 wpad-basic_2019-04-21-63962824-1_mipsel_24kc.ipk
256188 wpad-mini_2019-04-21-63962824-1_mipsel_24kc.ipk
427475 wpad-openssl_2019-04-21-63962824-1_mipsel_24kc.ipk
423071 wpad-wolfssl_2019-04-21-63962824-1_mipsel_24kc.ipk
new 2019-08-08 (2.9):
290217 wpad-basic_2019-08-08-ca8c2bd2-1_mipsel_24kc.ipk
258745 wpad-mini_2019-08-08-ca8c2bd2-1_mipsel_24kc.ipk
431732 wpad-openssl_2019-08-08-ca8c2bd2-1_mipsel_24kc.ipk
427641 wpad-wolfssl_2019-08-08-ca8c2bd2-1_mipsel_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This also syncs the configuration files with the default configuration
files, but no extra options are activated or deactivated.
The mesh patches were partially merged into hostapd 2.8, the remaining
patches were extracted from patchwork and are now applied by OpenWrt.
The patches still have open questions which are not fixed by the author.
They were taken from this page:
https://patchwork.ozlabs.org/project/hostap/list/?series=62725&state=*
The changes in 007-mesh-apply-channel-attributes-before-running-Mesh.patch
where first applied to hostapd, but later reverted in hostapd commit
3e949655ccc5 because they caused memory leaks.
The size of the ipkgs increase a bit (between 1.3% and 2.3%):
old 2018-12-02 (2.7):
283337 wpad-basic_2018-12-02-c2c6c01b-11_mipsel_24kc.ipk
252857 wpad-mini_2018-12-02-c2c6c01b-11_mipsel_24kc.ipk
417473 wpad-openssl_2018-12-02-c2c6c01b-11_mipsel_24kc.ipk
415105 wpad-wolfssl_2018-12-02-c2c6c01b-11_mipsel_24kc.ipk
new 2019-04-21 (2.8):
288264 wpad-basic_2019-04-21-63962824-1_mipsel_24kc.ipk
256188 wpad-mini_2019-04-21-63962824-1_mipsel_24kc.ipk
427475 wpad-openssl_2019-04-21-63962824-1_mipsel_24kc.ipk
423071 wpad-wolfssl_2019-04-21-63962824-1_mipsel_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
For AP mode, OpenWrt automatically sets ieee80211w to either 1 or 2, depending
on whether the encryption is set to sae-mixed, or sae/owe/eap suite-b.
Mirror the same defaults for client mode connections, in order to allow an
OpenWrt station to associate to an OpenWrt ap with SAE, OWE or Suite-B encryption
without the need to manually specify "option ieee80211w" on the station.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This changes fixes the generation of the wpa_supplicant client configuration
in WPA3 OWE client mode. Instead of incorrectly emitting key_mgmt=NONE, use
the proper key_mgmt=OWE setting instead.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
wps_supplicant.h assumes that 'struct wpa_bss' is forward declared if
CONFIG_WPS is not defined. With the later inclusion of
600-ubus_support, the issue manifests in warnings like these:
wps_supplicant.h:113:15: warning: 'struct wpa_bss' declared inside parameter list will not be visible outside of this definition or declaration
struct wpa_bss *bss)
^~~~~~~
This patch forward declares 'struct wpa_bss' regardless.
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit message facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The original wpa_hexdump uses a 'void *' for the payload. With patch
410-limit_debug_messages, the signature changes and compiler warnings
occur at various places. One such warning is:
wpa_debug.h:106:20: note: expected 'const u8 * {aka const unsigned char *}' but argument is of type 'struct wpa_eapol_key *'
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit message facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
commit eb204d14f75c ("base-files: implement generic service_running")
introduced generic service_running so it's not needed to copy&paste same
3 lines over and over again.
I've removed service_running from netifd/network init script as well,
because it was not working properly, looked quite strange and I didn't
understand the intention:
$ /etc/init.d/network stop
$ service network running && echo "yes" || echo "nope"
( have to wait for 30s )
Command failed: Request timed out
yes
Signed-off-by: Petr Štetiar <ynezz@true.cz>
e73bf11 config: ra_management compatibility support
d818380 odhcpd: router: Fix out of scope memory access
94a1c94 dhcpv6-ia: free assignment when validity timer expires
752fc2c router: speed up initial router advertisements
09aa022 router: close socket upon NETEV_IFINDEX_CHANGE fixed
79eb160 router: fix previous commit
6034b5c router: close socket upon NETEV_IFINDEX_CHANGE
000182f router: fix lingering uloop socket descriptor
f6c2242 router: support ra_lifetime being 0
d111809 router: make RA flags configurable (FS#2019)
Update odhcpd defaults according to the new RA flags implementation
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This adds the key_type and ec_curve options to enable the generation of
EC keys during initialization, using openssl or the new options added to
px5g.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This commit will activate CONFIG_IEEE80211W for all, but the mini
variant when at least one driver supports it. This will add ieee80211w
support for the mesh variant for example.
Fixes: FS#2397
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This changes the default PKG_BUILD_DIR to take BUILD_VARIANT into
account (if set), so that packages do not need to manually override
PKG_BUILD_DIR just to handle variants.
This also updates most base packages with variants to use the updated
default PKG_BUILD_DIR.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
Backport upstream patches pre 2.81rc for testing purposes.
Let's see what falls out!
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
To configure the list of allowable TLS 1.3 ciphersuites, the option
tls_ciphersuites is used instead of tls_ciphers.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This edjusts the selection of recently removed wolfssl options which
have always been built into the library even in their abscence.
Also remove the selection of libwolfssl itself, allowing the library to
be built as a module.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This addresses an issue where the list option specified in
/etc/config/openvpn i.e. 'tls_cipher' would instead show up in the
generated openvpn-<name>.conf as 'ncp-ciphers'. For context,
'ncp_ciphers' appears after 'tls_cipher' in OPENVPN_LIST from
openvpn.options.
Also, the ordering of the options in the UCI config file is now
preserved when generating the OpenVPN config. The two currently
supported list options deal with cipher preferences.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
* curve25519: not all linkers support bmi2 and adx
This should allow WireGuard to build on older toolchains.
* global: switch to coarse ktime
Our prior use of fast ktime before meant that sometimes, depending on how
broken the motherboard was, we'd wind up calling into the HPET slow path. Here
we move to coarse ktime which is always super speedy. In the process we had to
fix the resolution of the clock, as well as introduce a new interface for it,
landing in 5.3. Older kernels fall back to a fast-enough mechanism based on
jiffies.
https://lore.kernel.org/lkml/tip-e3ff9c3678b4d80e22d2557b68726174578eaf52@git.kernel.org/https://lore.kernel.org/lkml/20190621203249.3909-3-Jason@zx2c4.com/
* netlink: cast struct over cb->args for type safety
This follow recent upstream changes such as:
https://lore.kernel.org/lkml/20190628144022.31376-1-Jason@zx2c4.com/
* peer: use LIST_HEAD macro
Style nit.
* receive: queue dead packets to napi queue instead of empty rx_queue
This mitigates a WARN_ON being triggered by the workqueue code. It was quite
hard to trigger, except sporadically, or reliably with a PC Engines ALIX, an
extremely slow board with an AMD LX800 that Ryan Whelan of Axatrax was kind
enough to mail me.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Support to disable the timestamp check for certificates in
wpa_supplicant (Useful for devices without RTC that cannot
reliably get the real date/time) has been accepted in the
upstream hostapd. It's implemented in wpa_supplicant as a
per-AP flag tls_disable_time_checks=[0|1].
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The OpenWrt buildroot ABI version rebuild tracker does not handle
transient dependencies, therefor add all libraries linked by uhttpd
as direct dependencies to the corresponding binary package definition.
This ensures that uhttpd is automatically rebuilt and relinked if any
of these libraries has its ABI_VERSION updated in the future.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This is to make life easier for users with customized build of
dnsmasq-full variant. Currently dnsmasq config generated by current
service script will be rejected by dnsmasq build lacking DHCP feature
- Options like --dhcp-leasefile have default values. Deleting them
from uci config or setting them to empty value will make them take on
default value in the end
- Options like --dhcp-broadcast are output unconditionally
Tackle this by
- Check availablility of features from output of "dnsmasq --version"
- Make a list of options guarded by HAVE_xx macros in src/options.c of
dnsmasq source code
- Ignore these options in xappend()
Two things to note in this implementation
- The option list is not exhaustive. Supposedly only those options that
may cause dnsmasq to reject with "unsupported option (check that
dnsmasq was compiled with DHCP/TFTP/DNSSEC/DBus support)" are taken
into account here
- This provides a way out but users' cooperation is still needed. E.g.
option dnssec needs to be turned off, otherwise the service script
will try to add --conf-file pointing to dnssec specific anchor file
which dnsmasq lacking dnssec support will reject
Resolves FS#2281
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
There was an issue with the backport compat layer in yesterday's snapshot,
causing issues on certain (mostly Atom) Intel chips on kernels older than
4.2, due to the use of xgetbv without checking cpu flags for xsave support.
This manifested itself simply at module load time. Indeed it's somewhat tricky
to support 33 different kernel versions (3.10+), plus weird distro
frankenkernels.
If OpenWRT doesn't support < 4.2, you probably don't need to apply this.
But it also can't hurt, and probably best to stay updated.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* tools: add wincompat layer to wg(8)
Consistent with a lot of the Windows work we've been doing this last cycle,
wg(8) now supports the WireGuard for Windows app by talking through a named
pipe. You can compile this as `PLATFORM=windows make -C src/tools` with mingw.
Because programming things for Windows is pretty ugly, we've done this via a
separate standalone wincompat layer, so that we don't pollute our pretty *nix
utility.
* compat: udp_tunnel: force cast sk_data_ready
This is a hack to work around broken Android kernel wrapper scripts.
* wg-quick: freebsd: workaround SIOCGIFSTATUS race in FreeBSD kernel
FreeBSD had a number of kernel race conditions, some of which we can vaguely
work around. These are in the process of being fixed upstream, but probably
people won't update for a while.
* wg-quick: make darwin and freebsd path search strict like linux
Correctness.
* socket: set ignore_df=1 on xmit
This was intended from early on but didn't work on IPv6 without the ignore_df
flag. It allows sending fragments over IPv6.
* qemu: use newer iproute2 and kernel
* qemu: build iproute2 with libmnl support
* qemu: do not check for alignment with ubsan
The QEMU build system has been improved to compile newer versions. Linking
against libmnl gives us better error messages. As well, enabling the alignment
check on x86 UBSAN isn't realistic.
* wg-quick: look up existing routes properly
* wg-quick: specify protocol to ip(8), because of inconsistencies
The route inclusion check was wrong prior, and Linux 5.1 made it break
entirely. This makes a better invocation of `ip route show match`.
* netlink: use new strict length types in policy for 5.2
* kbuild: account for recent upstream changes
* zinc: arm64: use cpu_get_elf_hwcap accessor for 5.2
The usual churn of changes required for the upcoming 5.2.
* timers: add jitter on ack failure reinitiation
Correctness tweak in the timer system.
* blake2s,chacha: latency tweak
* blake2s: shorten ssse3 loop
In every odd-numbered round, instead of operating over the state
x00 x01 x02 x03
x05 x06 x07 x04
x10 x11 x08 x09
x15 x12 x13 x14
we operate over the rotated state
x03 x00 x01 x02
x04 x05 x06 x07
x09 x10 x11 x08
x14 x15 x12 x13
The advantage here is that this requires no changes to the 'x04 x05 x06 x07'
row, which is in the critical path. This results in a noticeable latency
improvement of roughly R cycles, for R diagonal rounds in the primitive. As
well, the blake2s AVX implementation is now SSSE3 and considerably shorter.
* tools: allow setting WG_ENDPOINT_RESOLUTION_RETRIES
System integrators can now specify things like
WG_ENDPOINT_RESOLUTION_RETRIES=infinity when building wg(8)-based init
scripts and services, or 0, or any other integer.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Upstream PPP project has added in commit 8e77984 options to tune discovery
timeout and attempts in the rp-pppoe plugin.
Expose these options in the uci datamodel for pppoe:
padi_attempts: Number of discovery attempts
padi_timeout: Initial timeout for discovery packets in seconds
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
c9d9dbf pppoe: Custom host-uniq tag
44012ae plugins/rp-pppoe: Fix compile errors
Refresh patches
Drop 520-uniq patch as upstream accepted
Drop 150-debug_compile_fix patch as fixed upstream
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
41a74cb config: remove 'ignore' config option
c0c8034 treewide: init assignment lists head
f98b7ee config: use list safe iterator in lease_delete
3c9810b dhcpv4: fix lease ordering by ip address
b60c384 config: use multi-stage parsing of uci sections
a2dd8d6 treewide: always init interface list heads during initialization
a17665e dhcpv4: do not allow pool end address to overlap with broadcast address
6b951c5 treewide: give file descriptors safe initial value
39e11ed dhcpv4: DHCP pool size is off-by-one
4a600ce dhcpv4: add support for Parameter Request List option 55
09e5eca dhcpv4: fix DHCP packet size
3cd4876 ndp: fix syslog flooding (FS#2242)
79fbba1 config: set default loglevel to LOG_WARNING
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
fcb076c Various fixes for errors found by coverity static analysis (#109)
d98ab38 Merge branch 'pppd_print_changes' of https://github.com/nlhintz/ppp into nlhintz-pppd_print_changes
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This reverts commit c6aa9ff388.
Further testing has revealed that we will need to allow concurrent
requests after all, especially for situations where CGI processes
initiate further HTTP requests to the local host.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
EAP-pwd missing commit validation
Published: April 10, 2019
Identifiers:
- CVE-2019-9497 (EAP-pwd server not checking for reflection attack)
- CVE-2019-9498 (EAP-pwd server missing commit validation for
scalar/element)
- CVE-2019-9499 (EAP-pwd peer missing commit validation for
scalar/element)
Latest version available from: https://w1.fi/security/2019-4/
Vulnerability
EAP-pwd implementation in hostapd (EAP server) and wpa_supplicant (EAP
peer) was discovered not to validate the received scalar and element
values in EAP-pwd-Commit messages properly. This could result in attacks
that would be able to complete EAP-pwd authentication exchange without
the attacker having to know the used password.
A reflection attack is possible against the EAP-pwd server since the
hostapd EAP server did not verify that the EAP-pwd-Commit contains
scalar/element values that differ from the ones the server sent out
itself. This allows the attacker to complete EAP-pwd authentication
without knowing the password, but this does not result in the attacker
being able to derive the session key (MSK), i.e., the attacker would not
be able to complete the following key exchange (e.g., 4-way handshake in
RSN/WPA).
An attack using invalid scalar/element values is possible against both
the EAP-pwd server and peer since hostapd and wpa_supplicant did not
validate these values in the received EAP-pwd-Commit messages. If the
used crypto library does not implement additional checks for the element
(EC point), this could result in attacks where the attacker could use a
specially crafted commit message values to manipulate the exchange to
result in deriving a session key value from a very small set of possible
values. This could further be used to attack the EAP-pwd server in a
practical manner. An attack against the EAP-pwd peer is slightly more
complex, but still consider practical. These invalid scalar/element
attacks could result in the attacker being able to complete
authentication and learn the session key and MSK to allow the key
exchange to be completed as well, i.e., the attacker gaining access to
the network in case of the attack against the EAP server or the attacker
being able to operate a rogue AP in case of the attack against the EAP
peer.
While similar attacks might be applicable against SAE, it should be
noted that the SAE implementation in hostapd and wpa_supplicant does
have the validation steps that were missing from the EAP-pwd
implementation and as such, these attacks do not apply to the current
SAE implementation. Old versions of wpa_supplicant/hostapd did not
include the reflection attack check in the SAE implementation, though,
since that was added in June 2015 for v2.5 (commit 6a58444d27fd 'SAE:
Verify that own/peer commit-scalar and COMMIT-ELEMENT are different').
Vulnerable versions/configurations
All hostapd versions with EAP-pwd support (CONFIG_EAP_PWD=y in the build
configuration and EAP-pwd being enabled in the runtime configuration)
are vulnerable against the reflection attack.
All wpa_supplicant and hostapd versions with EAP-pwd support
(CONFIG_EAP_PWD=y in the build configuration and EAP-pwd being enabled
in the runtime configuration) are vulnerable against the invalid
scalar/element attack when built against a crypto library that does not
have an explicit validation step on imported EC points. The following
list indicates which cases are vulnerable/not vulnerable:
- OpenSSL v1.0.2 or older: vulnerable
- OpenSSL v1.1.0 or newer: not vulnerable
- BoringSSL with commit 38feb990a183 ('Require that EC points are on the
curve.') from September 2015: not vulnerable
- BoringSSL without commit 38feb990a183: vulnerable
- LibreSSL: vulnerable
- wolfssl: vulnerable
Acknowledgments
Thanks to Mathy Vanhoef (New York University Abu Dhabi) for discovering
and reporting the issues and for proposing changes to address them in
the implementation.
Possible mitigation steps
- Merge the following commits to wpa_supplicant/hostapd and rebuild:
CVE-2019-9497:
EAP-pwd server: Detect reflection attacks
CVE-2019-9498:
EAP-pwd server: Verify received scalar and element
EAP-pwd: Check element x,y coordinates explicitly
CVE-2019-9499:
EAP-pwd client: Verify received scalar and element
EAP-pwd: Check element x,y coordinates explicitly
These patches are available from https://w1.fi/security/2019-4/
- Update to wpa_supplicant/hostapd v2.8 or newer, once available
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
[bump PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
hostapd: fix SAE confirm missing state validation
Published: April 10, 2019
Identifiers:
- CVE-2019-9496 (SAE confirm missing state validation in hostapd/AP)
Latest version available from: https://w1.fi/security/2019-3/
Vulnerability
When hostapd is used to operate an access point with SAE (Simultaneous
Authentication of Equals; also known as WPA3-Personal), an invalid
authentication sequence could result in the hostapd process terminating
due to a NULL pointer dereference when processing SAE confirm
message. This was caused by missing state validation steps when
processing the SAE confirm message in hostapd/AP mode.
Similar cases against the wpa_supplicant SAE station implementation had
already been tested by the hwsim test cases, but those sequences did not
trigger this specific code path in AP mode which is why the issue was
not discovered earlier.
An attacker in radio range of an access point using hostapd in SAE
configuration could use this issue to perform a denial of service attack
by forcing the hostapd process to terminate.
Vulnerable versions/configurations
All hostapd versions with SAE support (CONFIG_SAE=y in the build
configuration and SAE being enabled in the runtime configuration).
Possible mitigation steps
- Merge the following commit to hostapd and rebuild:
SAE: Fix confirm message validation in error cases
These patches are available from https://w1.fi/security/2019-3/
- Update to hostapd v2.8 or newer, once available
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
[bump PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
EAP-pwd side-channel attack
Published: April 10, 2019
Identifiers:
- CVE-2019-9495 (cache attack against EAP-pwd)
Latest version available from: https://w1.fi/security/2019-2/
Vulnerability
Number of potential side channel attacks were recently discovered in the
SAE implementations used by both hostapd and wpa_supplicant (see
security advisory 2019-1 and VU#871675). EAP-pwd uses a similar design
for deriving PWE from the password and while a specific attack against
EAP-pwd is not yet known to be tested, there is no reason to believe
that the EAP-pwd implementation would be immune against the type of
cache attack that was identified for the SAE implementation. Since the
EAP-pwd implementation in hostapd (EAP server) and wpa_supplicant (EAP
peer) does not support MODP groups, the timing attack described against
SAE is not applicable for the EAP-pwd implementation.
A novel cache-based attack against SAE handshake would likely be
applicable against the EAP-pwd implementation. Even though the
wpa_supplicant/hostapd PWE derivation iteration for EAP-pwd has
protections against timing attacks, this new cache-based attack might
enable an attacker to determine which code branch is taken in the
iteration if the attacker is able to run unprivileged code on the victim
machine (e.g., an app installed on a smart phone or potentially a
JavaScript code on a web site loaded by a web browser). This depends on
the used CPU not providing sufficient protection to prevent unprivileged
applications from observing memory access patterns through the shared
cache (which is the most likely case with today's designs).
The attacker could use information about the selected branch to learn
information about the password and combine this information from number
of handshake instances with an offline dictionary attack. With
sufficient number of handshakes and sufficiently weak password, this
might result in full recovery of the used password if that password is
not strong enough to protect against dictionary attacks.
This attack requires the attacker to be able to run a program on the
target device. This is not commonly the case on an authentication server
(EAP server), so the most likely target for this would be a client
device using EAP-pwd.
The commits listed in the end of this advisory change the EAP-pwd
implementation shared by hostapd and wpa_supplicant to perform the PWE
derivation loop using operations that use constant time and memory
access pattern to minimize the externally observable differences from
operations that depend on the password even for the case where the
attacker might be able to run unprivileged code on the same device.
Vulnerable versions/configurations
All wpa_supplicant and hostapd versions with EAP-pwd support
(CONFIG_EAP_PWD=y in the build configuration and EAP-pwd being enabled
in the runtime configuration).
It should also be noted that older versions of wpa_supplicant/hostapd
prior to v2.7 did not include additional protection against certain
timing differences. The definition of the EAP-pwd (RFC 5931) does not
describe such protection, but the same issue that was addressed in SAE
earlier can be applicable against EAP-pwd as well and as such, that
implementation specific extra protection (commit 22ac3dfebf7b, "EAP-pwd:
Mask timing of PWE derivation") is needed to avoid showing externally
visible timing differences that could leak information about the
password. Any uses of older wpa_supplicant/hostapd versions with EAP-pwd
are recommended to update to v2.7 or newer in addition to the mitigation
steps listed below for the more recently discovered issue.
Possible mitigation steps
- Merge the following commits to wpa_supplicant/hostapd and rebuild:
OpenSSL: Use constant time operations for private bignums
Add helper functions for constant time operations
OpenSSL: Use constant time selection for crypto_bignum_legendre()
EAP-pwd: Use constant time and memory access for finding the PWE
These patches are available from https://w1.fi/security/2019-2/
- Update to wpa_supplicant/hostapd v2.8 or newer, once available
- Use strong passwords to prevent dictionary attacks
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
[bump PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
SAE side-channel attacks
Published: April 10, 2019
Identifiers:
- VU#871675
- CVE-2019-9494 (cache attack against SAE)
Latest version available from: https://w1.fi/security/2019-1/
Vulnerability
Number of potential side channel attacks were discovered in the SAE
implementations used by both hostapd (AP) and wpa_supplicant
(infrastructure BSS station/mesh station). SAE (Simultaneous
Authentication of Equals) is also known as WPA3-Personal. The discovered
side channel attacks may be able to leak information about the used
password based on observable timing differences and cache access
patterns. This might result in full password recovery when combined with
an offline dictionary attack and if the password is not strong enough to
protect against dictionary attacks.
Cache attack
A novel cache-based attack against SAE handshake was discovered. This
attack targets SAE with ECC groups. ECC group 19 being the mandatory
group to support and the most likely used group for SAE today, so this
attack applies to the most common SAE use case. Even though the PWE
derivation iteration in SAE has protections against timing attacks, this
new cache-based attack enables an attacker to determine which code
branch is taken in the iteration if the attacker is able to run
unprivileged code on the victim machine (e.g., an app installed on a
smart phone or potentially a JavaScript code on a web site loaded by a
web browser). This depends on the used CPU not providing sufficient
protection to prevent unprivileged applications from observing memory
access patterns through the shared cache (which is the most likely case
with today's designs).
The attacker can use information about the selected branch to learn
information about the password and combine this information from number
of handshake instances with an offline dictionary attack. With
sufficient number of handshakes and sufficiently weak password, this
might result in full discovery of the used password.
This attack requires the attacker to be able to run a program on the
target device. This is not commonly the case on access points, so the
most likely target for this would be a client device using SAE in an
infrastructure BSS or mesh BSS.
The commits listed in the end of this advisory change the SAE
implementation shared by hostapd and wpa_supplicant to perform the PWE
derivation loop using operations that use constant time and memory
access pattern to minimize the externally observable differences from
operations that depend on the password even for the case where the
attacker might be able to run unprivileged code on the same device.
Timing attack
The timing attack applies to the MODP groups 22, 23, and 24 where the
PWE generation algorithm defined for SAE can have sufficient timing
differences for an attacker to be able to determine how many rounds were
needed to find the PWE based on the used password and MAC
addresses. When the attack is repeated with multiple times, the attacker
may be able to gather enough information about the password to be able
to recover it fully using an offline dictionary attack if the password
is not strong enough to protect against dictionary attacks. This attack
could be performed by an attacker in radio range of an access point or a
station enabling the specific MODP groups.
This timing attack requires the applicable MODP groups to be enabled
explicitly in hostapd/wpa_supplicant configuration (sae_groups
parameter). All versions of hostapd/wpa_supplicant have disabled these
groups by default.
While this security advisory lists couple of commits introducing
additional protection for MODP groups in SAE, it should be noted that
the groups 22, 23, and 24 are not considered strong enough to meet the
current expectation for a secure system. As such, their use is
discouraged even if the additional protection mechanisms in the
implementation are included.
Vulnerable versions/configurations
All wpa_supplicant and hostapd versions with SAE support (CONFIG_SAE=y
in the build configuration and SAE being enabled in the runtime
configuration).
Acknowledgments
Thanks to Mathy Vanhoef (New York University Abu Dhabi) and Eyal Ronen
(Tel Aviv University) for discovering the issues and for discussions on
how to address them.
Possible mitigation steps
- Merge the following commits to wpa_supplicant/hostapd and rebuild:
OpenSSL: Use constant time operations for private bignums
Add helper functions for constant time operations
OpenSSL: Use constant time selection for crypto_bignum_legendre()
SAE: Minimize timing differences in PWE derivation
SAE: Avoid branches in is_quadratic_residue_blind()
SAE: Mask timing of MODP groups 22, 23, 24
SAE: Use const_time selection for PWE in FFC
SAE: Use constant time operations in sae_test_pwd_seed_ffc()
These patches are available from https://w1.fi/security/2019-1/
- Update to wpa_supplicant/hostapd v2.8 or newer, once available
- In addition to either of the above alternatives, disable MODP groups
1, 2, 5, 22, 23, and 24 by removing them from hostapd/wpa_supplicant
sae_groups runtime configuration parameter, if they were explicitly
enabled since those groups are not considered strong enough to meet
current security expectations. The groups 22, 23, and 24 are related
to the discovered side channel (timing) attack. The other groups in
the list are consider too weak to provide sufficient security. Note
that all these groups have been disabled by default in all
hostapd/wpa_supplicant versions and these would be used only if
explicitly enabled in the configuration.
- Use strong passwords to prevent dictionary attacks
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
[bump PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
With this change, the file is reduced from 5186 bytes to 4649 bytes that
its approximately 10.5 percent less memory consumption. For small
devices, sometimes every byte counts.
Also, all other protocol handler use tabs instead of spaces.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Fix dbclient regression in 2019.77. After exiting the terminal would be left
in a bad state. Reported by Ryan Woodsmall
drop patch applied upstream:
010-tty-modes-werent-reset-for-client.patch
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* allowedips: initialize list head when removing intermediate nodes
Fix for an important regression in removing allowed IPs from the last
snapshot. We have new test cases to catch these in the future as well.
* tools: warn if an AllowedIP has a nonzero host part
If you try to run `wg set wg0 peer ... allowed-ips 192.168.1.82/24`, wg(8)
will now print a warning. Even though we mask this automatically down to
192.168.1.0/24, usually when people specify it like this, it's a mistake.
* wg-quick: add 'strip' subcommand
The new strip subcommand prints the config file to stdout after stripping
it of all wg-quick-specific options. This enables tricks such as:
`wg addconf $DEV <(wg-quick strip $DEV)`.
* tools: avoid unneccessary next_peer assignments in sort_peers()
Small C optimization the compiler was probably already doing.
* peerlookup: rename from hashtables
* allowedips: do not use __always_inline
* device: use skb accessor functions where possible
Suggested tweaks from Dave Miller.
* blake2s: simplify
* blake2s: remove outlen parameter from final
The blake2s implementation has been simplified, since we don't use any of the
fancy tree hashing parameters or the like. We also no longer separate the
output length at initialization time from the output length at finalization
time.
* global: the _bh variety of rcu helpers have been unified
* compat: nf_nat_core.h was removed upstream
* compat: backport skb_mark_not_on_list
The usual assortment of compat fixes for Linux 5.1.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
OpenVPN as of 2.4.7 uses some OpenSSL APIs that are deprecated in
OpenSSL >= 1.1.0.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [white space fix]
Instead of creating host-routes depending on fwmark as (accidentally)
pushed by commit
1e8bb50b93 ("wireguard: do not add host-dependencies if fwmark is set")
use a new config option 'nohostroute' to explicitely prevent creation
of the route to the endpoint.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The 'fwmark' option is used to define routing traffic to
wireguard endpoints to go through specific routing tables.
In that case it doesn't make sense to setup routes for
host-dependencies in the 'main' table, so skip setting host
dependencies if 'fwmark' is set.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
- limit ECC support to ec*-sha2-nistp256:
* DROPBEAR_ECC now provides only basic support for ECC
- provide full ECC support as an option:
* DROPBEAR_ECC_FULL brings back support for ec{dh,dsa}-sha2-nistp{384,521}
- update feature costs in binary size
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
* option "keyfile" is more generic than "rsakeyfile".
* option "rsakeyfile" is considered to be deprecated and should be removed
in future releases.
* warn user (in syslog) if option "rsakeyfile" is used
* better check options ("rsakeyfile" and "keyfile"): don't append
"-r keyfile" to command line if file is absent (doesn't exist or empty),
warn user (in syslog) about such files
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Felix Fietkau pointed out that bundled libtomcrypt/libtommath do funny stuff with CFLAGS.
fix this with checking environment variable OPENWRT_BUILD in both libs.
change in dropbear binary size is drastical: 221621 -> 164277.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
compiler complains about messed up CFLAGS in build log:
<command-line>: warning: "_FORTIFY_SOURCE" redefined
<command-line>: note: this is the location of the previous definition
and then linker fails:
mips-openwrt-linux-musl-gcc [...] -o dropbearmulti [...]
collect2: fatal error: ld terminated with signal 11 [Segmentation fault]
compilation terminated.
/staging_dir/toolchain-mips_24kc_gcc-8.2.0_musl/mips-openwrt-linux-musl/bin/ld: /tmp/cc27zORz.ltrans0.ltrans.o: relocation R_MIPS_HI16 against `cipher_descriptor' can not be used when making a shared object; recompile with -fPIC
/staging_dir/toolchain-mips_24kc_gcc-8.2.0_musl/mips-openwrt-linux-musl/bin/ld: /tmp/cc27zORz.ltrans1.ltrans.o: relocation R_MIPS_HI16 against `ses' can not be used when making a shared object; recompile with -fPIC
/staging_dir/toolchain-mips_24kc_gcc-8.2.0_musl/mips-openwrt-linux-musl/bin/ld: /tmp/cc27zORz.ltrans2.ltrans.o: relocation R_MIPS_HI16 against `cipher_descriptor' can not be used when making a shared object; recompile with -fPIC
/staging_dir/toolchain-mips_24kc_gcc-8.2.0_musl/mips-openwrt-linux-musl/bin/ld: BFD (GNU Binutils) 2.31.1 assertion fail elfxx-mips.c:6550
[...]
/staging_dir/toolchain-mips_24kc_gcc-8.2.0_musl/mips-openwrt-linux-musl/bin/ld: BFD (GNU Binutils) 2.31.1 assertion fail elfxx-mips.c:6550
make[3]: *** [Makefile:198: dropbearmulti] Error 1
make[3]: *** Deleting file 'dropbearmulti'
make[3]: Leaving directory '/build_dir/target-mips_24kc_musl/dropbear-2018.76'
make[2]: *** [Makefile:158: /build_dir/target-mips_24kc_musl/dropbear-2018.76/.built] Error 2
make[2]: Leaving directory '/package/network/services/dropbear'
This FTBFS issue was caused by hardening flags set up by dropbear's configure script.
By default, Dropbear offers hardening via CFLAGS and LDFLAGS,
but this may break or confuse OpenWrt settings.
Remove most Dropbear's hardening settings in favour of precise build,
but preserve Spectre v2 mitigations:
* -mfunction-return=thunk
* -mindirect-branch=thunk
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
* wg-quick: freebsd: allow loopback to work
FreeBSD adds a route for point-to-point destination addresses. We don't
really want to specify any destination address, but unfortunately we
have to. Before we tried to cheat by giving our own address as the
destination, but this had the unfortunate effect of preventing
loopback from working on our local ip address. We work around this with
yet another kludge: we set the destination address to 127.0.0.1. Since
127.0.0.1 is already assigned to an interface, this has the same effect
of not specifying a destination address, and therefore we accomplish the
intended behavior. Note that the bad behavior is still present in Darwin,
where such workaround does not exist.
* tools: remove unused check phony declaration
* highlighter: when subtracting char, cast to unsigned
* chacha20: name enums
* tools: fight compiler slightly harder
* tools: c_acc doesn't need to be initialized
* queueing: more reasonable allocator function convention
Usual nits.
* systemd: wg-quick should depend on nss-lookup.target
Since wg-quick(8) calls wg(8) which does hostname lookups, we should
probably only run this after we're allowed to look up hostnames.
* compat: backport ALIGN_DOWN
* noise: whiten the nanoseconds portion of the timestamp
This mitigates unrelated sidechannel attacks that think they can turn
WireGuard into a useful time oracle.
* hashtables: decouple hashtable allocations from the main device allocation
The hashtable allocations are quite large, and cause the device allocation in
the net framework to stall sometimes while it tries to find a contiguous
region that can fit the device struct. To fix the allocation stalls, decouple
the hashtable allocations from the device allocation and allocate the
hashtables with kvmalloc's implicit __GFP_NORETRY so that the allocations fall
back to vmalloc with little resistance.
* chacha20poly1305: permit unaligned strides on certain platforms
The map allocations required to fix this are mostly slower than unaligned
paths.
* noise: store clamped key instead of raw key
This causes `wg show` to now show the right thing. Useful for doing
comparisons.
* compat: ipv6_stub is sometimes null
On ancient kernels, ipv6_stub is sometimes null in cases where IPv6 has
been disabled with a command line flag or other failures.
* Makefile: don't duplicate code in install and modules-install
* Makefile: make the depmod path configurable
* queueing: net-next has changed signature of skb_probe_transport_header
A 5.1 change. This could change again, but for now it allows us to keep this
snapshot aligned with our upstream submissions.
* netlink: don't remove allowed ips for new peers
* peer: only synchronize_rcu_bh and traverse trie once when removing all peers
* allowedips: maintain per-peer list of allowedips
This is a rather big and important change that makes it much much faster to do
operations involving thousands of peers. Batch peer/allowedip addition and
clearing is several orders of magnitude faster now.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
omcproxy's configuration is lost on every update or installation.
Avoid it by defining the configuration file.
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
max_ttl - limit the ttl in the dns answer if greater as $max_ttl
min_cache_ttl - force caching of dns answers even the ttl in the answer
is lower than the $min_cache_ttl
max_cache_ttl - cache only dns answer for $max_cache_ttl.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
This makes it clear that localuse when explicitly specified in the
config will have its final say on whether or not the initscript should
touch /etc/resolv.conf, no matter whatever the result of previous
guesswork would be
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Cherry-pick Multi-AP commits from uptream:
9c06f0f6a hostapd: Add Multi-AP protocol support
5abc7823b wpa_supplicant: Add Multi-AP backhaul STA support
a1debd338 tests: Refactor test_multi_ap
bfcdac1c8 Multi-AP: Don't reject backhaul STA on fronthaul BSS
cb3c156e7 tests: Update multi_ap_fronthaul_on_ap to match implementation
56a2d788f WPS: Add multi_ap_subelem to wps_build_wfa_ext()
83ebf5586 wpa_supplicant: Support Multi-AP backhaul STA onboarding with WPS
66819b07b hostapd: Support Multi-AP backhaul STA onboarding with WPS
8682f384c hostapd: Add README-MULTI-AP
b1daf498a tests: Multi-AP WPS provisioning
Add support for Multi-AP to the UCI configuration. Every wifi-iface gets
an option 'multi_ap'. For APs, its value can be 0 (multi-AP support
disabled), 1 (backhaul AP), 2 (fronthaul AP), or 3 (fronthaul + backhaul
AP). For STAs, it can be 0 (not a backhaul STA) or 1 (backhaul STA, can
only associate with backhaul AP).
Also add new optional parameter to wps_start ubus call of
wpa_supplicant to indicate that a Multi-AP backhaul link is required.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Currently it seems impossible to configure /etc/config/dhcp to achieve
the following use case
- run dnsmasq with no-resolv
- re-generate /etc/resolv.conf with "nameserver 127.0.0.1"
Before this change, we have to set resolvfile to /tmp/resolv.conf.auto
to achive the 2nd effect above, but setting resolvfile requires noresolv
being false.
A new boolean option "localuse" is added to indicate that we intend to
use dnsmasq as the local dns resolver. It's false by default and to
align with old behaviour it will be true automatically if resolvfile is
set to /tmp/resolv.conf.auto
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
