libiptc.pc depends on libip[4|6]tc.pc, thus all of those need to be
installed.
Should fix collectd build and thus #13146; which should make collectd
appear in snapshots again.
Signed-off-by: Danny Baumann <dannybaumann@web.de>
SVN-Revision: 36509
And while at it, also include a define check for BCM6328, thanks to
Gabor for spotting this.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 36506
Update the numbering of kernel patch for supporting
Netgear WNR2000v3 from 617 to 618.
Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36498
Fix "Widening multiply-accumulate operation uses wrong value extension"
for 4.7, 4.7-linaro and 4.6-linaro, which backported the broken code to 4.6.
Vanilla 4.6 is unaffected.
Fixes#13420.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 36486
I recently picked up a WNDR3700 to put OpenWRT on, and only after tearing into the box did I find it
was one of the v3 boards, with poor OpenWRT support. This patch should add the board detection and
LED/button control to the broadcom-diag module, and should generate a netgear .chk image that the
bootloader and stock firmware will accept.
The changes to the broadcom-diag module are more than a few lines because the WNDR3700v3 is driving
its LEDs through an HC164 8-bit shift register.
Signed-off-by: Owen Kirby <osk@exegin.com>
SVN-Revision: 36482
Hardcoding channel number to 11 is a bad idea, it may be even not
available on some devices. If there are two single-band radios, the
one for 5GHz doesn't have 11 channel.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 36479
Network connectivity works fine (LAN and WAN).
For GPIOs, only pwr led and the green wan leds are supported for now.
Signed-off-by: Mathieu Olivari <mathieu.olivari@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36459
Add support for TPLINK WR720N v3 which has 4MB flash,
32MB ram, 2 ethernet interfaces, 1 USB 2.0 port.
The patch is mostly a modification from mach-tl-wr703n.c.
GPIO numbers for the slider switch is from mach-tl-mr3020n.c.
Tested on my device and they worked fine.
Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36456
Only difference between Generic and P1020 is that P1020
enables SMP with two CPUs in the kernel config.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36454
This upgrades the AT91 target to 3.8.7, and migrates to device tree.
This allows a single kernel to be built for most at91 variants which
simplifies things quite a bit. The immediate result is that all
subtargets are nuked, and any boards without dts files are no longer
supported, though the target now includes more boards than before. The
adc driver was also nuked as 3.8.7 includes a new one under the IIO
subsystem.
Signed-off-by: Adam Porter <porter.adam@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36452
