The nvmem-cells is deprecated. Also simplify mac address settings.
Fixes: b4086f4 ("mediatek: add support for YunCore AX835")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
The mac address of the network port under the switch is
the same as the corresponding gmac by default, so there
is no need to repeat the setting. Compile test only.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
The GS110TUP v1 is a managed switch similar to the GS110TPP v1, but with
port 10 as SFP instead of RJ-45 and a total budget of 240 watts. Ports
1-4 support 60-watt 802.3bt PoE and ports 5-8 support 30-watt 802.3at.
The flash layout of the two switches are identical, and the U-Boot
configurations are the same except for having a different magic number,
so installation can be done via the same U-Boot method.
The following command will be needed to enable the port LEDs as per
https://forum.openwrt.org/t/72510/51 :
fw_setenv bootcmd "rtk network on; boota"
Additionally, port 9 (1000base-T from a separate QSGMII PHY) does not
function without this. Port 10 was not tested as no SFP module was
available.
Signed-off-by: Jacob Potter <jacob@j4cbo.com>
[rebase on merged flash layout]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Flash layouts for GS108Tv3, GS110TPPv1, GS308Tv1 and GS310TPv1 are
almost identical, except for the uimage header magic.
Move the flash layout to the common dtsi, and only place the magic value
in the device dts files.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Make the call deferred instead of blocking to avoid deadlock issues
Fixes: 3df9322771 ("hostapd: make ubus calls to wpa_supplicant asynchronous")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reverts commit b7f9742da8.
There are several reports of regressions with this commit. Will be added
back once I've figured out and fixed the cause
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When hitting a timing window where ubus configuration calls are hitting hostapd
and wpa_supplicant simultaneously, they can deadlock waiting for each other.
Fix this by using a lock around the ubus calls.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This fixes a deadlock issue where depending on the setup order, hostapd and
wpa_supplicant could end up waiting for each other
Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Read back the reset register in order to flush the cache. This fixes
spurious reboot hangs on TP-Link TL-WDR3600 and TL-WDR4300 with Zentel
DRAM chips.
This issue was fixed in the past, but switching to the reset-driver
specific implementation removed the cache barrier which was previously
implicitly added by reading back the register in question.
Link: https://github.com/freifunk-gluon/gluon/issues/2904
Link: https://github.com/openwrt/openwrt/issues/13043
Link: https://dev.archive.openwrt.org/ticket/17839
Link: f8a7bfe1cb2c ("MIPS: ath79: fix system restart")
Signed-off-by: David Bauer <mail@david-bauer.net>
Modems which are using qmi do not reply on the 1st sync but they do
on subsequent. Sometimes uqmi is hanging - even when using an early
dummy access to unlock the modem. To always guarantee a proper
initialisation, running or hanging uqmi processes must be stopped
before. All uqmi calls have now a timeout option -t to avoid hanging.
Signed-off-by: Uwe Niethammer <uwe@dr-niethammer.de>
TP-Link RE365 is a wireless range extender, hardware-wise resembles
RE305 with slight changes regarding buttons and LEDs.
Specification
SoC: MediaTek MT7628AN
RAM: 64 MiB DDR2
Flash: 8 MiB SPI NOR
WiFi: 2.4 GHz 2T2R integrated
5 GHz 2T2R MediaTek MT7612EN conncted to PCIe lanes
Ethernet: 1x 10/100 Mbps integrated
LEDs: 6x GPIO controlled
Buttons: 4x GPIO controlled
UART: row of 4 holes marked on PCB as J1, starting count from white
triangle
1. VCC (3.3V), 2. GND, 3. RX, 4. TX
baud: 57600, parity: none, flow control: none
Installation
1. Open web management interface.
2. Go to Settings > System Tools > Firmware upgrade.
3. Select "Browse" and select the OpenWrt image with factory.bin suffix.
4. After selecting "Upgrade" firmware writing process will start.
5. Wait till device reboots, power LED should stay solid when it's fully
booted, then it's ready for configuration through LAN port.
Additional information
With how device manufacturer patrtitioned the flash memory, it's possible
that with default packages set, initial factory.bin image won't be
created. In such case, try to reduce packages amount or use older release
for initial conversion to OpenWrt. Later You can use sysupgrade.bin
image with full set of packages because OpenWrt uses unpartitioned flash
memory space unused by vendor firmware.
Reverting to vendor firmware involves converting firmware using
tplink-safeloader with -z option (can be found in ImageBuilder or SDK)
and forcibly applying converted firmware as sysupgrade.
Known issues
WARNING: after removing casing of the device one is exposed to high
voltage and is in a risk of being electrocuted.
Caution when interfacing whith bootloader, saving its environment either
by issuing "saveenv" or selecting option "1: Load system code to SDRAM
via TFTP." in boot menu, any of those will lead to overwriting part of
kernel. This will lead to need of firmware recovery. The cause of this
issue is bootloader having environment offset on flash at 0x40000,
while kernel starts from 0x20000.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[Wrap long line in DTS]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Use postinst script to reload service instead of uci-defaults hack. It's
possible thanks to recent base-files change that executes postinst after
uci-defaults.
This fixes support for uhttpd customizations. It's possible (again) to
adjust uhttpd config with custom uci-defaults before it gets started.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Fixes: d25d281fd6 ("uhttpd: Reload config after uhttpd-mod-ubus was added")
Ref: b799dd3c70 ("base-files: execute package's "postinst" after executing uci-defaults")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Before, PVID is reset for all ports and goes out of bounds. Also, PVID
is later changed by dsa configuration by `ip link` and `bridge vlan`
commands, this does not change the CPU port PVID and CPU PVID stays 0.
It does not allow sending packets from OpenWrt to any connected devices
unless default configuration is changed
This change iterates up to and including cpu_port and sets default PVID
to 1. For lan* ports PVID can be configured with `ip link` and `bridge
vlan` commands
Acked-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Fix incorrect register value being set for VLAN_PORT_FWD
Before, the 0b1111 would be set for the register which means outgoing
packets would receive an extra tag, corresponding to the PVID of the
port.
On untagged ports, this meant outgoing packets with a single tag.
On tagged ports, this meant outgoing QinQ packets, where the inner tag
was either the PVID of the untagged ingress port, or the already
assigned original (single) tag.
Acked-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Without this, luci shows 10M full duplex when there is no link. So
explicitly set half duplex and unknown speed.
Acked-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Use led_setX to determine number of LEDs per port. Introduce macros to
calculate register value and shift for particular LED in a particular
set.
Problem with previous implementation is that it uses is10G status to
determine leds per port. However with usxgmii, driver sets 10g, 5g and
2.5g so even though there are only 2 leds per port it selects 4 leds per
port
This implementation relies on configured led_set node.
Acked-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Before driver code
- enabled egress filter for cpu and non-cpu ports
- enabled ingress filter for non-cpu ports
This patch explicitly enables ingress and egress filtering for non-cpu
ports and disables ingress and egress filtering for cpu port.
Acked-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Setting/clearing bits on the first byte of the mac address causes collisions
when using multiple SSIDs on both PHYs. Change the allocation to alter the
last byte instead.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
rpath handling seems to be more restrictive now. To deal with this,
link the libubox library from STAGING_DIR_HOST to STAGING_DIR_HOSTPKG, so that
packages installed to STAGING_DIR_HOSTPKG can pick it up. This mainly affects
ucode, but possibly other host builds as well
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 16MB NOR
RAM: 256MB
Ethernet: 2x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset
Power: DC 12V 1A, PoE 802.3af 48V
Flash instructions:
Option #1 - SSH
I was able to SSH into the stock firmware of my device.
1. Attach the router to the network
2. Use scp (-O) to copy the sysupgrade image
3. Connect using SSH and run `sysupgrade -n`
Option #2 - U-Boot
One way to use the bootloader for flashing is using TFTP:
1. Connect to the router using an ethernet cable
2 Spin up a TFTP server serving the sysupgrade file
3. Open the case and attach a UART
4. Attach power to the router and interrupt the countdown by pressing
any key
5. Select option #2 (Upgrade firmware)
6. Enter IP address information and image name
7. Wait patiently
Co-Authored-By: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net>
Co-Authored-By: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Adjust LED names and provide the OpenWrt status indicator aliases
to actually use LEDs by the OpenWrt boot & sysupgrade processes.
* Name both LEDs clearly by the color
* Add the missing OpenWrt LED status indicator aliases and
remove the now unnecessary default status from blue LED
After this commit, the LEDs are used as:
* bootloader, really early Linux boot: blue LED is on
* preinit/failsafe: white LED blinks rapidly
* late boot: white LED blinks slowly
* boot completed, running normally: blue LED is on
* sysupgrade: white LED blinks
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Incorrect PKG_MIRROR_HASH introduced on #14356
Fixes: 934873f451 ("ipq-wifi: bump version to 2024-01-06-71f45cff")
Signed-off-by: Manuel Fombuena <mfombuena@innovara.co.uk>
Previously the script would calculate the size of the compressed archive
which isn't the size installed in the overlayfs.
This commit uses zcat in combination with wc to calculate the
umcompressed size.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Using PKG_URL one may set the URL for all sub packages, which is usually
shared anyway. Future packages should only use PKG_URL instead of adding
it per sub-package.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The manifest should provide as much information as possible about the
package, including the project URL. With this commit the URL is stored
as it's own attribute instead of at the end of the description.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Hardware
--------
CPU: Qualcomm Atheros QCA9563
RAM: 128M DDR2
FLASH: 16MB SPI-NOR
WiFi: Qualcomm Atheros QCA9563 2x2:2 802.11n 2.4GHz
Qualcomm Atheros QCA9880 2x2:2 802.11ac 5GHz
Antennas
--------
The device features internal antennas as well as external antenna
connectors. By default, the internal antennas are used.
Two GPIOs are exported by name, which can be used to control the
antenna-path mux. Writing a logical 0 enables the external antenna
connectors.
Installation
------------
1. Download the OpenWrt sysupgrade image to the device. You can use scp
for this task. The default username and password are "ubnt" and the
device is reachable at 192.168.1.20.
$ scp -O openwrt-sysupgrade.bin ubnt@192.168.1.20:/tmp/firmware.bin
2. Connect to the device using SSH.
$ ssh ubnt@192.168.1.20
3. Disable the write-protect
$ echo "5edfacbf" > /proc/ubnthal/.uf
4. Verify kernel0 and kernel1 match mtd2 and mtd3
$ cat /proc/mtd
5. Write the sysupgrade image to kernel0 and kernel1
$ dd if=/tmp/firmware.bin of=/dev/mtdblock2
$ dd if=/tmp/firmware.bin of=/dev/mtdblock3
6. Write the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtd4
7. Reboot the device
$ reboot
Signed-off-by: David Bauer <mail@david-bauer.net>
Frequent crashes have been observed on MT7916 based platforms. While the
root of these crashes are currently unknown, they happen when decoding
rate information of connected STAs in AP mode. The rate-information is
associated with a band which is not available on the PHY.
Check for this condition in order to avoid crashing the whole system.
This patch should be removed once the roout cause has been found and
fixed.
Link: https://github.com/freifunk-gluon/gluon/issues/2980
Signed-off-by: David Bauer <mail@david-bauer.net>
Previous commits installed non-elf files into /lib/modules/$VER/.
COLLECT_KERNEL_DEBUG tries to strip all files and these two files
break the build.
Fix it by copying only kernel modules for debug info collection.
Fixes: e1d8e57614 ("kernel: include modinfo for built-in modules")
Fixes: 29f6da4340 ("kernel: include built-in module list")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This commit:
1. Removes deprecated "label" property from the dts leds subnnodes;
2. Updates buttons and leds dts description according to kernel docs
examples.
Scope: devices well known to me.
Run-tested: TP-Link ec330-g5u, WiFire S1500.nbn
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
The MikroTik RouterBOARD 911G-5HPacD is a stripped-down version of
RB921GS-5HPacD, removing the SFP cage.
This ports the board from ar71xx, and is based on support for
RB921GS-5HPacD.
Disable mdio1 and eth1 nodes in routerboard-92x.dtsi, then re-enable
them in devices using that, so the newly-added device has the port
disabled properly.
See https://mikrotik.com/product/RB911G-5HPacD for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9558 (720 MHz)
- RAM: 128 MB
- Storage: 128 MB NAND
- Wireless: external QCA9892 802.11a/ac 2x2:2
- Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in
Working:
- NAND storage detection
- Ethernet
- Wireless
- 1x user LED (blinks during boot, sysupgrade)
- Reset button
- Sysupgrade
Installation:
- Boot initramfs image via TFTP and then flash sysupgrade image
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
LEDs 1 through 5 are used for RSSI monitoring on factory firmware.
Reflect that by creating appropriate rssileds configuration.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
This is a stripped-down version of RB912UAG-(2,5)HPnD, without USB,
miniPCIe and SIM sockets.
This board has been supported in the ar71xx.
Add support based on RB912UAG board, by splitting out the common part to
.dtsi, and creating separate device tree for the stripped-down version.
Links:
* https://mikrotik.com/product/RB911G-2HPnD
* https://mikrotik.com/product/RB911G-5HPnD
* https://openwrt.org/toh/hwdata/mikrotik/mikrotik_rb911g-5hpnd
Hardware:
* SoC: Atheros AR9342,
* RAM: DDR 64MB,
* SPI NOR: 64KB,
* NAND: 128MB,
* Ethernet: x1 10/100/1000 port with passive POE in,
* Wi-Fi: 802.11 a/b/g/n (depending on band variant)
* LEDs: 5 general purpose LEDs (led1..led5), power LED, user LED,
Ethernet phy LED,
* Button,
* Beeper.
Flashing:
* Use the RouterBOARD Reset button to enable TFTP netboot,
boot kernel and initramfs and then perform sysupgrade.
* From ar71xx OpenWrt firmware run:
$ sysupgrade -F /tmp/<sysupgrade.bin>
For more info see: https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Image for RB912UAG-2HPnD supports the 5GHz variant without
modifications. Add it as alternative name, so it can be found easier.
While at that, adjust board display name in device tree, to reflect
that.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
MT7688 devices use the "mt7628an.dtsi" as the template. And RT3052
devices use the "rt3050.dtsi" as template. Therefore, we need to add
the corresponding system controller compatible strings to make them
work properly.
Fixes: 1f818b09f8 ("ramips: add proper system clock and reset driver support for legacy SoCs")
Fixes: #14305
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
