None of the LEDs are enabled by default on the Hornet-UB X2 board
(the 16/64MB version of the Hornet-UB), because it uses a different
board-name ("hornet-ub-x2"); but hornet-ub and hornet-ub-x2 boards
are equivalent WRT their LEDs.
SIgned-off-by: Joshua Judson Rosen <jrosen@harvestai.com>
SVN-Revision: 45328
On newer Mikrotik boards, the radio calibration data
is stored differently and uses LZO compression instead
of RLE.
Update the RouterBOOT helper code to support the new
format.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 45297
Platform device support has been removed from the gpio-74x164
driver in 3.14. Restore that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 45203
The setting has been lost during the transition to 3.18.
The CONFIG_M25PXX_PREFER_SMALL_SECTOR_ERASE option is not
available anymore, so use CONFIG_MTD_SPI_NOR_USE_4K_SECTORS
instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 45161
There were a few issues with the existing code to detect the model string:
* Always using the string starting with byte 56 would cut off the W of WNDR when
the ID starts with 29763654+16+64 instead of 29763654+16+128
* The string contained garbage after the zero byte instead of cutting it off
after the zero (which wasn't always visible using busybox tools, but could
confuse other scripts)
Tested on a WNDR3700v1 and a WNDR3700v2 using the new 29763654+16+64 ID in the
ART. Furthermore, tested against ART dumps of a WNDR3700v2 using the old
$'\xff...' value and a WNDR3800.
The [ -z "$model" ] check was dropped as there is no way to actually hit this
unless no ART partition is found at all.
The awk command was carefully crafted to work both with gawk and the (horribly
broken) busybox awk.
Fixes#18992.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 45140
There are two versions of the GL.iNet, the 6408A and the 6416A. The only
difference is the flash size.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44860
While the switch positions aren't explicitly labeled as on and off, we've heard
complaints about them being wrong. This patch changes the handling to match the
stock firmware.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44795
My previous patch regarding the Hornet-UB board
(commit: beed4d82d6a0154b0cd5f7b84e2180215ace6718) actually
causes the WPS led state to be inverted. Practically this meant
that value 0 in /sys/class/led/alfa:blue:wps/brightness would
turn the LED on and any positive value (1-255) would turn it off.
The above of course is confusing and hence reverting this value
back to the way it was before beed4d82d6a0154b0cd5f7b84e2180215ace6718.
Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>
SVN-Revision: 44791
This problem has existed at least since Attitude Adjustment and
is also present in trunk. Basically on the Hornet-UB board the
functionality of RESET and WPS have "switched places".
There are two tickets about the issue at dev.openwrt.org,
The solution suggested on them both is incomplete though
and introduces the following proglem:
Patching as suggested on #14136/#15282 will result in a situation
where simply pressing the RESET button on the bottom will cause
FACTORY RESET to be run. This is due to GPIO high/low state being
incorrect as a result of the above change and virtually the RESET
button is in the pressed-down state the entire time. When it is
then physically pressed, that causes the opposite, release, to be
triggered and since to the board it seemed that the button was
pressed long before it was released, the FACTORY RESET results.
The attached patch works as expected. I have verified both the
incorrect functionality as well as after fixing the issue as
described in the patch and flashing the resulting firmware to a
Hornet-UB board.
Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>
SVN-Revision: 44692
Previously, the generated images for the My Net Wi-fi Range Extender
wouldn't always work (and panic) due to the fixed mtd offsets and
sizes for the kernel and rootfs. This patch fixes the problem by
utilizing the shared Cybertan's partition parser to recalculate
the mtd partitions for every image dynamically everytime.
Reported-by: Pascal Paradis <peparadis@yahoo.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44665
By removing the NL16 signature check, the parser can be
utilized by other devices like the WD My Net Wi-fi Range
Extender.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44664
This patch renames the partition parser from
wrt160nl to more generic cybertan.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44663
405-mtd-tp-link-partition-parser.patch was updating the
WRT160NL's partition parser Kconfig. This patch moves the
relevant change into the right file:
404-mtd-wrt160nl-trx-parser.patch
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44662
Please also backport to Barrier Breaker (this same patch applies there too).
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 44647
OpenWrt can be flashed with following uboot commands:
tftpboot 0x80500000 openwrt-ar71xx-generic-wpj558-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 44620
CONFIG_GENERIC_NET_UTILS is selected by CONFIG_NET and already enabled
in generic config, so we don't need this symbol in platform specific
configurations.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44611
Most MIPS targets have it disabled, so move the symbol to the generic
configs to keep target configs small.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44583
The firware md5sum check never worked due to missing dollar signs.
Also suppress
`md5sum: can't open '/lib/firmware/ath10k/QCA988X/hw2.0/firmware-3.bin'`
error on any board not using ath10k.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44486
This patch adds corrected profile and build image for the TL-MR12U board.
Unfortunately i cannot test the factory image since i can't find anywhere
the original chinese firmware but
the generated openwrt-ar71xx-generic-tl-mr12u-v1-squashfs-sysupgrade.bin
worked just fine over a modified mr3040 factory image i managed to modify
to initially flash the mr12u from the original firmware.
Proper kernel support probably should be added since cat /proc/cpuinfo shows
MR13U.
Signed-off-by: Daniel Petre <daniel.petre@gmail.com>
SVN-Revision: 44427
This patch adds user-space support for the TL-MR12U board based on the mr13u patches.
Signed-off-by: Daniel Petre <daniel.petre@gmail.com>
SVN-Revision: 44426
This patch adds the mc-mac1200r target to do_load_ath10k_board_bin() in
target/linux/ar71xx/base-files/lib/preinit/81_load_ath10k_board_bin to load the
ath10k radio MAC address from the EEPROM in MERCURY MAC1200R devices
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44375
This patch adds support for MERCURY MAC1200R, a dual band 802.11bgn + 802.11ac
router based on the AR9344, with QCA988x ath10k radio and 5 Fast Ethernet ports
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44359
This device is very similar to the TL-WR841N v8, only two LED GPIOs are
different.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44255
The board is already supported by OpenWrt. WNR1000v2/WNR1000v2-VC are
pretty much the same as WNR2000v3/WNR612v2, therefore the same
initialization code and flash layout is used.
Signed-off-by: Ștefan Rusu <saltwaterc@gmail.com>
Tested-by: Douglas Fraser <1dsfraser@gmail.com>
SVN-Revision: 44221
Fix the WLAN MAC address to match the one printed on the label by using the
correct address from the ART instead of the address of the LAN interface.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44183
This patch adds an entry in the uci-defaults' led-file to configure the
WAN and WLAN LEDs by default.
Signed-off-by: Vincent Wiemann <me@bibbl.com>
SVN-Revision: 44165
TP-LINK TL-WR843ND v1 is the same model like wr41, but with
Power over Ethernet on wan port.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 44085
the GPIO controlling the rf filter is not configured properly by this patch.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44077
This patch adds soc support for QCA9561 and TP9343.
TP9343 is a reduced version of QCA9561, which can be found in TP-LINK routers in China.
The qca956x_wmac has not yet been supported by ath9k.
tested on TL-WDR6500 and TL-WR882N v1 (Chinese version)
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 43744
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43715
It moves firmware patch code behind an extra check on board_name.
Otherwise it will calculate firmware checksum for unaffected boards.
It also reduce boottime by a md5 calculation and removes error message
on boot if firmware not found.
SVN-Revision: 43679
I don't see that we're in an atomic context so there's no need to
busy-wait. Therefore replace the delay with sleep calls.
See also Documentation/timers/timers-howto.txt. It states:
"In general, use of mdelay is discouraged and code should
be refactored to allow for the use of msleep."
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43539
Replace the fixed wait time of 1s with polling for BMCR_RESET
to be cleared on all PHYs.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43538
Patch to add the buildprofile for the GL-Init-6408A-v1 and the GL-Inet-6416A-v1
Both devices are identical, only difference is one comes with 8MB flash and
the other with 16MB flash
Official website: http://www.gl-inet.com/w/?page_id=241&lang=en
Comprehensive list of specs: https://revspace.nl/GL-Inet
Signed-off-by: Martijn Zilverschoon <martijn@friedzombie.com>
SVN-Revision: 43462
This adds support for the TP-LINK CPE210/220/510/520 (Pharos series). These
devices are very similar to the Ubiquiti NanoStations, but with better specs:
faster CPU, more RAM, 2x2 MIMO.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 43385
replace all occurences of LINUX_VERSION with the cleaner
approach. future kernel upgrades must mostly touch only
one file. the only platform left is netlogic, because it
uses a intermediate kernel 3.14.16
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 43047
This patch changes the code of the Wi-Fi On/Off button on the TP-Link WR1043ND v2
from KEY_WLAN to KEY_RFKILL (and renames a few constants to match). The reason
for this change is, that the KEY_WIFI button code is not recognized by the
hotplug subsystem. This means that the userspace is not notified about the
button being pressed which effectively renders it useless.
Signed-off-by: Josef Gajdusek <atx@atx.name>
SVN-Revision: 42922
Currently JFFS2 end-of-filesystem marker 0xdeadc0de is included the
computation of image's MD5 checksum as part of the seama header. But
OpenWrt will erase blocks including and after the marker thus
invalidating the checksum after the first boot.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 42915
Qihoo C301 has 2 flash chips of which one is used as primary and the
other is used as backup. OEM U-Boot will try to boot an activeregion N
with imageNstatus=0 and imageNtrynum <= imagemaxtry. If such a region
is found, bootloader will try to increment imageNtrynum and boot it.
This patch tries to reset imageNtrynum after each successful boot (if
the boot process reaches the execution of /etc/init.d/done).
root@OpenWrt:/# hexdump -C -n 128 /dev/mtdblock9
00000000 9e f3 63 91 61 63 74 69 76 65 72 65 67 69 6f 6e |..c.activeregion|
00000010 3d 31 00 69 6d 61 67 65 31 73 74 61 74 75 73 3d |=1.image1status=|
00000020 30 00 69 6d 61 67 65 32 73 74 61 74 75 73 3d 30 |0.image2status=0|
00000030 00 69 6d 61 67 65 32 74 72 79 6e 75 6d 3d 30 00 |.image2trynum=0.|
00000040 69 6d 61 67 65 6d 61 78 74 72 79 3d 33 00 69 6d |imagemaxtry=3.im|
00000050 61 67 65 31 74 72 79 6e 75 6d 3d 30 00 00 00 00 |age1trynum=0....|
00000060 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 42914
[base-files] shell-scripting: fix wrong usage of '==' operator
normally the '==' is used for invoking a regex parser and is a bashism.
all of the fixes just want to compare a string. the used busybox-ash
will silently "ignore" this mistake, but make it portable/clean at least.
this patch does not change the behavior/logic of the scripts.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42911
This patch fixes LED definitions for the DRAGINO2 board.
1. It renames the Router/USB led to System, as it is now marked "SYS" on the board.
2. It gives control of the LAN and WAN leds and some other GPIOs to Linux.
3. It fixes the active_low property for the LAN and WAN leds.
4. It sets up WLAN, LAN and WAN leds in the UCI defaults.
5. It allows usage of the System led by the diag.sh script, so it will be used to indicate boot and failsafe status.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 42897
All TP-LINK machine names begin with "TP-LINK", so there's no need to check for
more specific model names. This also allows adding new models like the Archer
series more easily.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 42795
A typo in the definition for the OM2P reset button disabled its functionality
in OpenWrt. The actual button for these two devices is "1" and not "11".
Signed-off-by: Oren Poleg <oren@poleg.org>
[sven@open-mesh.org: added a commit subject+message]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 42782
Qihoo 360 C301 is a dual band wireless router supports 802.11n and 802.11ac.
Its chipset is AR9344 + AR9882 with two 16MB flashes.
This patch adds its initial support.
v2:
* use mtd_get_mac_ascii to fetch MAC address for ath10k.
* use ath79_register_pci to initialize AR9882.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 42552
While the AR9331 has a gigabit MAC towards the internal switch, the
integrated PHYs however are only 100-base-tx capable. The existing code
however advertieses gigabit capability in the link status word. If you
attach such a PHY to a gigabit capable switch on the remote end, with
some probability it attempts to negotiate gigabit and fails, falling
baco to the AR9331 assuming a 10mbit half-duplex link. This has been
observed quite frequently with the Carambola2 and gigabit capable
switches.
In ath79_register_eth(), "pdata->has_gbit = 1;" is set unconditionally
for both AR9331 ethernet ports. This is most likely wrong. Despite the
two MAC IP cores being gigabit MACs, the MAC for eth1 is connected to a
100base-T PHY via MII. The has_gbit attribute is used in the ethernet
driver to determine the supported link modes.
So either pdata->has_gbit is not set to 1 anymore, or the ethernet
driver needs to be modified to determine the advertised link code word
on another criteria than pdata->has_gbit. This patch implements the
former solution.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
SVN-Revision: 42432
This improves performance when doing concurrent rx/tx on a single
ethernet MAC, e.g. when routing between VLANs.
Fixes#13072
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 42328
This sets the MAC address of the WLAN interface to the "official" primary MAC
address (the one on the label under the devices, and the one used with the stock
firmware). The MAC address used so far (primary-1) isn't even used at all with
the stock firmware, which sets (primary) on LAN and WLAN and (primary+1) on the
WAN interface (like OpenWrt does with this patch).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 42193
The OpenMesh MR600(v1) can only enable the 2.4G WiFi PHY LED through the
mini-PCIe device. Not configuring the LED pin inside the platform data
makes it impossible to configure it through any standard OpenWrt tool.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 42184
Apparently this is a fairly common refurb unit of the 3800 series now,
with merely the recognition string changed in the boot loader.
Signed-off-by: Dave Taht <dave.taht@bufferbloat.net>
SVN-Revision: 42023
Change list:
* Remove button info on GPIO12, there is no button there.
* Remove nvram mtd partition, as it's not used for anything, saves 64k for user data.
Tested building for carambola2 target.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
SVN-Revision: 41993
this caused factory resets when reboot was pressed
Signed-off-by: Brent Thomson <brentthomson@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41932
without this the build for NBG6716 fails due to missing packages
https://dev.openwrt.org/ticket/17325
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41930
The airGateway has a reset button connected to GPIO 12, so we should use it.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
SVN-Revision: 41794
The default case in 02_network is inappropriate for the MikroTik RouterBOARD 91x boards because they do not have a WAN port, so don't bother setting the non-existent eth1 interface as the WAN port.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
SVN-Revision: 41767
This patch adds support for the Ubiquiti Networks airGateway.
Based in part on code posted by David Hutchison <dhutchison@bluemesh.net> on openwrt-devel:
https://lists.openwrt.org/pipermail/openwrt-devel/2013-December/023035.html
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
SVN-Revision: 41766
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5838/
[juhosg:
- fix coding style,
- check the first and the last character of the MAC string
instead of using the strchr() function]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 41622
The GL-Connect GL.iNet v1 router is basically a TP-Link TL-WR703N with
more DRAM/Flash, 2x Ethernet ports and console/GPIO header in the same
small form-factor:
<http://www.gl-inet.com/w/?lang=en>
Moreover, the manufacturer is promoting the OpenWrt usage to replace
the original firmware and proposing patches against both AA and trunk:
<http://www.gl-inet.com/w/?p=398&lang=en>
This is a clean up of the original manufacturer GPLv2 patch by alzhao,
proposed to the list by Mark Janssen.
Signed-off-by: Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Mark Janssen <mark@sig-io.nl>
Signed-off-by: alzhao <alzhao@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5273/
[juhosg:
- remove user-space and image generation support, will be included
from other patches,
- fix coding style and drop superfluous comment in mach-gl-inet.c,
- rename and refresh kernel patch,
- adjust subject]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 41618
The RB2011UiAS is almost exactly the same as the RB2011UAS, which is
already supported. Hardware-wise, it adds a passive power injector on
Eth10. Software-wise, Routerboot passes a different board name on the
kernel command line. Hence the need for a patch.
Not yet working:
* touchscreen: doesn't work on RB2011UAS either. The touchscreen itself
seems to be driven by an ADS7843-compatible IC, but figuring out which
GPIO pins it's connected to is work for the future.
* control of power injector: remains off. Probably also GPIO-controlled.
Signed-off-by: Soren Harward <stharward@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5841/
[juhosg: rename and refresh the kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 41617
With help of this script the ath10k board.bin settings are loaded from
flash and saved to the ath10k firmware directory. The driver reads it
later in the boot process.
Signed-off-by: André Valentin <avalentin@marcant.net>
SVN-Revision: 41562
This patch adds support for the MikroTik RouterBOARD SXT Lite.
The new RB911L series is also supported as a result.
v2 of this patch fixes the wmac offset to match what is on the sticker.
v3 refreshes the patch against r41148 and defines the power led as the status led in diag.sh
v4 refreshes the patch against r41353 and fixes the patch path issue to make git am work correctly
v5 selects the kernel config option in the mikrotik profile rather than in the main ar71xx config
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41450
205-fix-headers_install.patch is obseleted by upstream commit 3246a0352e3d58380b9386570f1db1faf7edf8a8
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41351
This enables the procd nand upgrade for ZyXEL NBG 6716. Also the ubi config
is cleaned up to match the wndr4300.
Signed-off-by: André Valentin <avalentin@marcant.net>
SVN-Revision: 41346
WAN and LAN are swapped the wrong way around. This patch fixes that by adding the 951Ui-2HnD to ar71xx.sh and the relevant entry in 02_network.
This patch also defines the ACT LED as the status LED in diag.sh.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41255
I added WIFI LED support (so now AP blinks nicely), I removed WPS
button GPIO (as it doesn't exist) and changed GPIO for reset button.
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
SVN-Revision: 40976
This board manufactured by HiWiFi has the following features.
- Atheros 9331 SoC.
- 16MB flash and 64MB RAM.
- 4GB eMMC storage via SK6226 USB 2.0 controller.
- 2 LAN and 1 WAN ethernet ports with LEDs on them.
- 3 blue LEDs on the front panel.
- 1 button labeled as "reset".
- Powered by a USB cable.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 40973
The TL-WA730RE seems to be almost identical to TL-WA701ND, just
that it comes without PoE and a stock-firmware claiming the device
to be a "Range Extender".
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 40972
Detect TL-WA7510N v1 by the board name as defined in mach-tl-wa901nd.c
and add hardware ID to tplink_board_detect
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 40971
Dlink dir-615-e1 can use dir-600-a1's image, but the image can't be
uploaded through dlink's normal firmware update web page.
Add profile for dir-615-e1 so the generated image can be uploaded
through the firmware update web page.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
SVN-Revision: 40969
ARGC is a 'C-ism', but not known/valid in shell-syntax - insert the correct
var $# (=number of args) here. under normal conditions this had no impact,
but we should at least correct it. the error was observable like this:
root@box:~ [ -e "/etc/functions.sh" ] && . /etc/functions.sh
root@box:~ [ -e "/lib/functions.sh" ] && . /lib/functions.sh
root@box:~ . /lib/upgrade/platform.sh
root@box:~ . /lib/upgrade/common.sh
root@box:~ platform_check_image /tmp/myfirmware.bin
ash: bad number
root@box:~ echo $?
0
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 40915
The most important one is qca_force_host_mode, which also sets the
'Stream Disable' bit in the usbmode register.
Fixes usb stability issues on AR933x and AR7241/AR7242
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40841
The change is the same as ("kernel/generic: modify mtd related
patches"). Since these files are under files directory, not a files
directory of specific kernel version, better to also change them. So
it will avoid adding files to future specific files directory
(e.g. files-3.14) for this mtd related change.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
SVN-Revision: 40732
The RB91x boards are suffering from ethernet packet loss after a cold
boot. The cause of the problem is that the AR8035 PHYs requires special
register settings to work reliably on these boards.
Enable the RGMII TX, RX delays and disable SmartEE functionality of
the AR8035 PHYs. Also enable the RXD delay in the ETH_CFG register
to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40509
Add a patch for the at803x phy driver, in order to be able
to configure some register settings via platform data.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40507
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg: use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40500
With this patch OpenWRT supports the following on the ZyXEL NBG 6716:
-WiFi 2G (ath9k)
-WiFi 5G (ath10k)
-NAND flash
-2 Ethernet interfaces
-USB 2.0
-LEDs including switch
-reasonale defaults at first boot
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg:
- rename and refresh kernel patch,
- fix a few typos,
- change button key codes,
- use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40499
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40481
Apart from the wireless chip, the WNDR3700 v4 and the WNDR4300
is the same device. Indicate this in the kernel files.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40479
The 5V power of the USB is controlled by a GPIO pin of
the external WiFi chip. Setup the GPIO bitmasks in the
platform data of the WiFi chip to ensure that the 5V
power gets enabled by the ath9k driver.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40478
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40477
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40475
The bootloader does not initializes the output function
correctly for all LEDs. DO that from the board setup code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40474
The hardware manual says amber so change the color part of
the LED names to reflect that. Also update the constant names.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40473
Adds support for the received signal strength indicator LEDs of the
Bullet M, Nanostation M and Rocket M devices.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/5108/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40471
Move the comments out from the shell script to fix build
breakage introduced in r40464.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40466
The C7v2 has 16 MB flash and QCA9880-BR4A rev 2 supported by ath10k driver.
The C7v1 had 8 MB flash and the unsupported QCA9880-AR1A rev 1.
Signed-off-by: Adam Serbinski <adam@serbinski.com>
Patchwork: http://patchwork.openwrt.org/patch/5071/
[juhosg:
- remove the v2 specific profile add the ath10k driver to the existing
Archer C7 profile instead. Although on v1 devices it does not change
the non-working behaviour, but the ath10k driver is useful for users
whom have replaced the wifi card with a supported one in their units.
- update image/Makefile to build firmware image for both boards if the
Archer C7 profile is selected]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40463
Everything seems to be working fine. Potential issues:
* VLAN port IDs are reversed with regard to the numbers on the case.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 40400
I don't have access to the specs, so I'm not sure about every detail, but I
haven't seen any problems with my test system, a TL-WR841N v9. It looks pretty
much like a QCA955x without PCI, a little twist in the clock calculation and
a AR9331-compatible switch.
Features not yet supported:
* EHCI (my test system doesn't have USB)
* ? (I have no idea if the QCA953x has any other features I don't know about
that aren't used by the TL-WR841N v9)
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 40399
The version of TL-WDR4300 sold in Israel comes with a different
hardware id.
Patch-by: Daniel <daniel@makrotopia.org>
Patchwork: http://patchwork.openwrt.org/patch/5001/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40038
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg: use correct board name in uci-defaults/02_network]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40033
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg:
- use a separate patch for kernel changes,
- reorder Kconfig and Makefile entries,
- change function and variable names to be lowercase only
and fix misaligned tabs in mach-gs-oolite.c,
... ]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40032
The flash address passed to rb_init_info() is bogus,
use the predefined AR71XX_SPI_BASE macro instead.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39891
sizeof(array_from_function_definition) gives back the size of the pointer.
sizeof(type) * array_size should be used in memset.
Signed-off-by: David Völgyes <david.volgyes@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4950/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39890
The ar71xx platform always uses the eth0 interface to provide
access to the device in failsafe mode. Due to this, failsafe
access is broken on devices where the LAN ports are connected
to the 'eth1' interface.
Update the relevant script to correctly set the ifname variable
for these devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39752
The RB91x boards are using a serial shift register
connected to the SPI bus to drive some of the LEDs.
Rework the board setup code to register a SPI device
for that. This makes it possible to use the 'spi-74x164'
driver to control the device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39703
That will be used to drive the 74HC595 serial-in/parallel-out
8-bits shift register which can be found on some RouterBOARDs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39702
The serial flash devices used on the ROuterBOARDs are
supporting 4KiB erase blocks. Enable the small sector
erase option in the m25p80 driver to avoid superfluous
erase/write of adjacent blocks.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39696
I noticed that the patch at http://patchwork.openwrt.org/patch/4017/
for adding support for the MikroTik RouterBOARD 951Ui-2HnD had been
abandoned because it wasn't generated and sent to the mailing list
correctly and doesn't apply as a result. I have cleaned up this patch.
When testing this on real hardware, I also noticed that wireless didn't
work, so this patch fixes that as well.
This patch applies cleanly to SVN 39392.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Patchwork: http://patchwork.openwrt.org/patch/4773/
[juhosg:
- drop the 'rb951ui_wlan_init' function and rework the code to
use the recently introduced rb95x_wlan_init function instead,
- fix GPIO number of the port5 LED,
- rename LEDs according to the standard LED naming conventions,
and use 'rb' prefix in the names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39641
Patch-by: TenNinjas <tenninjas@tenninjas.ca>
Patchwork: http://patchwork.openwrt.org/patch/4849/
[juhosg:
- use the Archer C7 specific LED setup instead of adding
identical code]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39636
This missing bit of the hack saves hugely on instruction traps
on tcp connections to ar71xx based routers.
Patch-by: Dave Taht <dave.taht@bufferbloat.net>
Patchwork: http://patchwork.openwrt.org/patch/4905/
[juhosg: adjust subject, refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39626
Solves ticket #14356 <https://dev.openwrt.org/ticket/14356>
Without this patch, UART output will show only 4 partitions:
[ 0.740000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 0.750000] Creating 4 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000050000 : "u-boot"
[ 0.760000] 0x000000050000-0x000000070000 : "u-boot-env"
[ 0.770000] 0x000000070000-0x0000007f0000 : "firmware"
[ 0.790000] 0x0000007f0000-0x000000800000 : "art"
and then linux complains :VFS: Cannot open root device "(null)"
With this patch, UART out will show 7 partitions:
[ 0.740000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 0.750000] Creating 4 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.760000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.770000] 0x000000050000-0x0000007f0000 : "firmware"
[ 0.780000] 2 netgear-fw partitions found on MTD device firmware
[ 0.780000] 0x000000050000-0x00000014b440 : "kernel"
[ 0.790000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.800000] 0x00000014b440-0x0000007f0000 : "rootfs"
[ 0.810000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.820000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.830000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.830000] 0x000000340000-0x0000007f0000 : "rootfs_data"
[ 0.840000] 0x0000007f0000-0x000000800000 : "art"
This patch is tested against r39502 of trunk.
Signed-off-by: Jonathan Chang <changcs@santos.ee.ntu.edu.tw>
Patchwork: http://patchwork.openwrt.org/patch/4870/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39625
The mtdpartsize macro triggers shell errors on various Linux distributions
when the partname argument $(1) does not appear within the partmap $(2).
Change the sed pattern to only emit anything if a successful substitution
occured and only evaluate the arithmetic expression if something was printed
by the sed program.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39583
The original dragino2 board support was missing some changes from the
upstream svn repository (http://svn.dragino.com/dragino2) that supported
sysupgrade.
[juhosg: change subject]
Signed-off-by: Karl Palsson <karlp@remake.is>
Patchwork: http://patchwork.openwrt.org/patch/4801/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39429
On recent TL-WDR4300 boards the external LNAs of the 2.4GHz
interface are connected to GPIO lines. Because these GPIO
lines are disabled by default, the RX sensitivity of the
device is quite bad.
Setup the GPIOs of the external LNAs to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39392
Get the size of the mtd partitions directly from the
MTD layout and remove the superfluous macro parameters.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39384
The macro checks the size of the rootfs image even if
the second parameter of the macro contains the size of
an eraseblock. It is wrong because the size of the
kernel image will be adjusted to the next eraseblock
and the resulting image might be too large.
Fix the macro to check the size of the final image
instead of the rootfs image.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39383
Since that was the last configuration in defconfig directory we can drop the
defconfig init script too.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39373
The eth5 LED on the RB2011 is not working because the
LED control rule is missing. Fix it.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39335
The r39147 commit introduces a regression: at lease on some routers
with ar8216 switch large packets get lost if 802.1q tagged port is
used on the interface connected to the aforementioned switch.
The r39147 changes code in the way so interface is set to accept
packets no longer than max ethernet frame length for a given mtu.
Unfortunately ar8216 has a feature: it sends two additional bytes
as a packet header and those this header needs to be added to the
max frame length. Otherwise long enough packets get lost.
The problem only manuifests itself if interface is used in vlan
tagged mode. If interface is untagged then ar8216's header fits
into space used by 802.1q tag and not packets are lost.
Include two additional bytes in the max frame length calculation
to fix the issue.
This patch is tested and works with Trendnet TEW-632BRP.
Signed-off-by Nikolay Martynov <mar.kolya@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4656/
[juhosg:
- simplify the patch to include the additional bytes of the
switch header unconditionally,
- change subject and update commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39219
The built-in wireless MAC of the AR934x SoC can handle
external LNAs and the control signal of the LNAs can be
routed to any GPIO line. Add a helper function which
can be used to configure the GPIO lines.
The helper function will be used for AR934x boards
which are using externel LNAs to improve sensitivity.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39215
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.
Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Tested-by: Steven Haigh <netwiz@crc.id.au>
Patchwork: http://patchwork.openwrt.org/patch/4689/
[juhosg:
- remove the GPIO LED changes, the My Net N600 has no yellow LEDs at all,
- change subject and update the commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39214
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.
Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4688/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39213
The hardware supports large ethernet frames. Override
the maximum frame length and packet lenght mask in the
platform data to allow to use large MTU on the ethernet
interfaces.
Limit the feature to AR934x SoCs for now. It should work
on some other SoCs as well, but those has not been tested
yet.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39149
The currently used bitmask of the maximum frame length field
is wrong for both models. On AR724x/AR933x the largest frame
size is 2047 bytes, on the AR934x it is 16383 bytes.
Make the MTU setup code model specific, and use the correct
bitmask for both models. Also change the value to the maximum.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39148
Set the MAX_FRAME_LEN register to zero in ag71xx_hw_init()
and write the correct value into that from the ag71xx_open()
and ag71xx_fast_reset() functions.
Also recalculate the RX buffer size based on the actual
maximum frame length value to optimize memory allocation.
Additionaly, disallow to change the MTU value while the
interface it running.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39147
The currently used bitmask is not correct for all SoCs.
Introduce a new field in struct ag71xx and store the
bitmask in that. Use the current value for now, it will
be adjusted for each SoCs in further patches.
Aslo use the new field directly in the ag71xx_rx_packets
and ag71xx_hard_start_xmit() functions and remove the
ag71xx_desc_pktlen() helper.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39144
Now that the switch works correctly we can enable the images for this
board.
Flashing from the factory firmware, the factory failsafe loader and
sysupgrade was tested successfully.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4617/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39130
Now that the switch is working correctly I had the chance to actually
test the LED config.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4616/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39129
The bootloader on the WD My Net N750 disables the ports on it's internal
AR8327N switch by powering them down. The stock firmware then brings the
ports back up again by starting the auto negotiation process on each
port.
This fix implements just that.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4615/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39128
This enables us to add fixups to the board specific code for boards that
require special treatment of PHYs on mdio bus reset.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
http://patchwork.openwrt.org/patch/4614/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39127
This enables us to modify the ag71xx_mdio_platform_data from within the
board support files.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4613/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39126
Currently, the AG71XX_RX_PKT_SIZE value limits the received
frame size to 1514/1516 bytes with/without a VLAN header
respectively. However the hardware limit is controlled by
the value the AG71XX_REG_MAC_MFL register which contains
the value of the max_frame_len field.
Compute the RX buffer size from the max_frame_len field
to get rid of the 1514/1516 byte limitation. Also remove
the unused AG71XX_RX_PKT_SIZE definition.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39121
The ar7240_probe function uses the network device name
in the kernel log messages, however the name is not yet
initialized when the ar7240_probe function is called.
Use the mdio bus name in the messages to avoid ugly
log lines like the following one:
eth%d: Found an AR7240/AR9330 built-in switch
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39116
The ag71xx debugfs code uses the network device name
for the device specific debugfs directory. Since r38689
'ar71xx: ag71xx: fix a race involving netdev registration'
the debugfs initialization happens before the ethernet
device gets registered and the network device name contains
'eth%d' at this point. If the board setup code registers
multiple ag71xx devices, the debugfs code tries to create
the device specific dir with the same name which causes
an error like this:
eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
ag71xx: probe of ag71xx.0 failed with error -12
Use the device name for the debugfs directory to avoid the
collisions. Also add an error message and change the return
code if the debugfs_create_dir call fails.
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39115
It is only on RB911G-5HPnD and RB912UAG-5HPnD boards.
The LEDs and the USB port is not working yet.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39102
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
[juhosg: remove the image generation part until the ethernet
switch issue is resolved]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39078
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
[juhosg: use a separate patch for kernel changes]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39077
The TL-WA801ND v2 board has only one LAN port which makes
it more similar to the TL-WR[78]50RE devices. Move the
board setup code into the mach-tl-wax50re.c file.
Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39072
This way it is a bit easier to add other TP-LINK devices based on the
Atheros AP123 reference board with one LAN port.
Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39071
Patch to add the user space support for the TL-WA801ND v2
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4501/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39064
Patch to add kernel support for the TP-LINK WA801ND v2
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4500/
[juhosg:
- the TL-WA801ND v2 does not have a sliding switch, it uses a push button
for WPS instead. Use the tl_mr3420v2_gpio_keys array to reflect that,
- rename kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39063
That function provides a slightly improved sanity check than the
currently used solution.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38967
This patch enables the convenient sysupgrade feature for
WD's Wi-Fi Range Extender.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4341/
[juhosg:
- rename 'mynet_rext_check_image' function to 'cybertan_check_image'
and move that into platform.sh,
- remove the the model specific 'platform_do_upgrade_mynet_rext' function,
- drop the mynet-rext.sh script,
- remove the image/Makefile change,
- update commit message]
[christian:
- check all 8 bytes of the firmware/device magic]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38966
Make the Image/Build/CyberTAN macro more generic,
and use simple wrappers for the GZIP/LZMA variants.
This simplifies the Makefile a bit, and allows to
build sysupgrade images for the devices which are
using LZMA compressed uImages.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38965
In the current sysupgrade images, the CRC32 value of
the TRX header covers the whole rootfs data. Due to
this, the CRC value should be changed during sysupgrade
otherwise the bootloader refuses to load the image on
the next boot.
Change the image generation to create sysupgrade images
where the CRC32 value covers the kernel data only. This
allows to skip the 'fixtrx' step during sysupgrade on
the target.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38964
- partitions on factory fw are a bit strange
- unknown contained some strings in factory
- unknown2 contains some atheros (2nd art ?)
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4149/
[juhosg: edit commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38954
There was no way to determine a working config, because
the switch (ar8337) was not working previously.
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4470/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38953
The device has three extra LEDs which indicate the quality
of the wireless link. Thanks to rssileds, this feature now
works out of the box.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4462/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38950
This patch improves support for the device considerably.
1. The wifi didn't work in the initial release. This was because
the WMAC of the AR9340 is not connected to the antennas.
(However, it can pick up wifi signals, if they are strong enough!)
Instead there's a dedicated AR9300 chip on the same board, which
works.
2. Ethernet throughput is improved. iperf shows that the hardware
can sustain more than 200Mbit/s and no longer drops any packages
when the link is under load.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4461/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38949
The F1E Phy (AR8035?) requires additional bits to be
set in order to provide a fast and reliable connection
over gigabit links.
When enabled, the link doesn't suffer anymore from a small
package loss under load and the performance is improved
quite a bit as well. (203 mbit/s vs 112 mbit/s, iperf tcp).
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4460/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38948
Small update to uci_defaults/01_leds, to support the usb led
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4426/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38947
Just a small oversight my part, added the support for the USB led
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4425/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38946
Patch to add the profile for the TP-LINK WR842N/ND v2
Small update, because of a change in the Makefile.
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4382/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38815
Patch to add the user space support for the TL-WR842N/ND v2
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4354/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38814
Get the factory assigned mac addresses stored in the caldata
partition and asign them to lan and wan interfaces. Also put
the correct mac addresses into the WiFi eeprom files to ensure
that the ath9k driver will use the correct ones.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Patchwork: http://patchwork.openwrt.org/patch/4350/
[juhosg:
- move WiFi MAC address setup to the firmware hotplug file,
- use the official MAC address for the 2.4GHz as well,
- remove uci-defaults.sh modifications,
- update commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38812
The current implementation of mtd will not append the backup
file created by sysupgrade to the correct partition, as mtd will append
the data to first jffs2 partition it finds. As the kernel is also
stored on a jffs2 partition (which resides before the overlay
partition), the data will be appended to this partition.
To fix this problem, a new option
-s <number> skip the first n bytes when appending data to the jffs2 partiton, defaults to "0"
is added to mtd.
Signed-off-by: Peter Wagner <tripolar@gmx.at>
SVN-Revision: 38807
Patch to add user space support for the TL-WA750RE/WA850RE range extender
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38718
Patch to add kernel support for the TP-LINK WA750RE and the WA850RE
range extender
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
[juhosg: rename and refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38717
In particular, phy_connect before register_netdev. This is because
register_netdev runs the netdev notifiers, which can race with the rest of
the initialization in ag71xx_probe. In my case this manifested in two ways:
1) If ag71xx is compiled as a module and inserted after netifd has started,
netifd is notified by register_netdev before the call to
ag71xx_phy_connect. netifd tries to bring the interface up, which calls
ag71xx_open, which in turn enters ag71xx_phy_start. This keys off
ag->phy_dev (which is still NULL) and thinks this is a fixed-link board,
and enters ag71xx_link_adjust. This looks at ag->speed which is not yet
initialized and hits the BUG() in the switch (ag->speed) in
ag71xx_link_adjust.
This is the wrong code path for ag71xx_phy_start - my board has PHYs that
need to be brought up with phy_start. Doing ag71xx_phy_connect before
register_netdev ensures that ag->phy_dev is non-NULL before
ag71xx_phy_start is ever called.
2) When ag71xx is built into the kernel, and netconsole is enabled, there
is a gap in the initial burst of replayed printks right after the netdev
comes up. My assumption is that netconsole is also triggered by a netdev
notifier, and part of this printk burst happens before the call into
ag71xx_phy_connect, so part of the burst is lost while the PHY comes up.
This patch fixes the gap - all the printks before eth0 comes up are bursted
in full when netconsole initializes.
ag71xx_phy_connect_xxx no longer runs with a registered netdev, so the
logging has been adjusted accordingly to avoid "unregistered net_device" or
"eth%d" messages in dmesg.
Signed-off-by: Catalin Patulea <cat@vv.carleton.ca>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38689
Patchwork: http://patchwork.openwrt.org/patch/4281/
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
[juhosg:
- remove the Image/Build/CyberTANLZMA/loader macro, it is not used
- move the MYNETREXT SingleProfile definition to the correct place]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38688
This patch adds a new device definition for a
Western Digital device. The hardware seems to
be based on Qualcomm Atheros DB120 design.
Patchwork: http://patchwork.openwrt.org/patch/4281/
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
[juhosg: refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38686
Append EOF markers to the END of the UBI image
file. This forces the kernel to erase all blocks
after the marker even if those blocks are not
empty.
Additionally, the resulting image can be flashed
from the original web UI now, so use '-factory'
suffix for that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38683
Extended the Makefile to generate a working factory reset image
for Netgear WNDR4300. The image uses UBI with two volumes squashfs
(rootfs) and JFFS2 (rootfs_data). In order to make stock U-Boot
happy, a fake rootfs image is placed into the last erase block
of the kernel partition.
Signed-off-by: Stefan Agner <stefan@agner.ch>
[juhosg:
- restore the NetgearNAND/initramfs macro,
- remove unused {Squash,Ubi}fsTemplate macros,
- remove board specific mtd options from CONFIG_CMDLINE, append the
board specific ubi.mtd parameter to the kernel command line instead,
- increase kernel partition size to 2MiB,
- use board specific ini file for ubinize,
- put jffs2 eof mark into the rootfs_data ubi volume,
- use KDIR_TMP for temporary images,
- use the squashfs-raw image,
- increase kernel partition size to 2MiB,
- use a local ubinize macro,
- fix macro parameter comments,
- put the fake rootfs into the last erase block of the kernel
partition,
- move Image/Build/NetgearNAND/buildkernel macro before
define Image/Build/NetgearNAND,
- don't use the wndr3700 utility, use '-M' parameter of mkimage to set
the uImage magic,
- use '-recovery' suffix for the generated image, it is only usable via
the fw_recovery function of the bootloader,
- update commit log]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38655
Add new subtarget nand with UBI/UBIFS including GLUEBI and squashfs.
This target will be used for NAND based router which make use of
UBI (and maybe UBIFS later on) in order to provide proper NAND
support.
Signed-off-by: Stefan Agner <stefan@agner.ch>
[juhosg:
- tweak target.mk:
change BOARDNAME variable,
improve Target/Description,
remove targz and ubifs from FEATURES and add broken flag,
- optimize kernel configuration:
disable ubifs, it is not used yet,
disable unused MTD options,
disable SPI support
disable unused network drivers,
tune kernel command line,
- remove image/ubinize.cfg, it will be in a follow-up patch
- move profile modifications into a separate patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38646
Ensures that the 'Default' images are generated
even if the subtarget has no profiles.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38635
Patchwork: http://patchwork.openwrt.org/patch/4183/
Signed-off-by: Terry Yang <yangbo@bhunetworks.com>
[juhosg:
- remove MultiProfile, it makes no sense for a single board
- move SingleProfile call and the mtdlayout to a different
location keep things sorted (well, almost)]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38593
BXU2000n-2 A1 is a BHU Networks WLAN board, use ar9341 chip.
Patchwork: http://patchwork.openwrt.org/patch/4183/
Signed-off-by: Terry Yang <yangbo@bhunetworks.com>
[juhosg:
- rename and refresh kernel patch,
- fix some checkpatch warnings and adjust whitespaces in
mach-bhu-bxu2000n2-a.c]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38591
This patch adds support for DRAGINO2 board (used by
Meshpotato v2). Most of the files included can be
found in the official svn repository provided by the
company [1]. I have just adapt it to the last OpenWrt
trunk revision (Fri Oct 4 10:49:47 2013).
1. http://svn.dragino.com/dragino2
Patchwork: http://patchwork.openwrt.org/patch/4234/
Signed-off-by: Pau Escrich <p4u@dabax.net>
[juhosg:
- rename and refresh kernel patch,
- fix checkpatch warnings in mach-dragino2.c]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38587
It is for Mikrotik devices only, rename the subtarget
to reflect that. Also fix the wget2nand script to use
the new image names.
Based on the patch by Stefan Agner:
http://patchwork.openwrt.org/patch/4123/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38509
The nand subtarget supports Mikrotik boards only. Change
the title and the description to reflect that.
Based on the patch by Stefan Agner:
http://patchwork.openwrt.org/patch/4123/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38508
Ensure that menuconfig shows the correct help text for
subtargets.
Based on the patch by Stefan Agner:
http://patchwork.openwrt.org/patch/4123/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38507
Both Allnet and OpenMesh sysupgrade uses fw_setenv from uboot-envtools to
change different settings in the uboot environment. uboot-envtools version
2013.01 introduced a filesystem lock "/var/lock/fw_printenv.lock" to guarantee
mutually exclusive access to the uboot environment. But the path /var doesn't
exist on the sysupgrade ramfs.
An upgrade on these devices fails since r36033 ("[package] uboot-envtools:
upgrade to version 2013.01.01") with following messages:
Error opening lock file /var/lock/fw_printenv.lock
failed to update U-Boot environment
Creating the "/var/lock" path before running fw_setenv is therefore a
requirement unless the locking functionality in fw_setenv is removed or
replaced with optional locking.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38483
Fixes the 5 GHz LED.
The same function has no effect on the 2.4 GHz LED at all, so we might
as well remove it.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38482
Fix the image building code so that the kernel correctly
distinguishes between hardware revisions.
Signed-off-by: Mads Hansen <d@taba.se>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38192
This patch adds support for the hardware slide switch on
the TL-MR3040 v2.
Signed-off-by: Mads Hansen <d@taba.se>
[juhosg: use EV_SW instead of EV_KEY]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38190
Remove the kernel and rootfs partitions. The Seama
parser can find those automatically:
0x000000070000-0x000000ff0000 : "firmware"
2 seama-fw partitions found on MTD device firmware
0x000000070000-0x0000001b0000 : "kernel"
0x0000001b0000-0x000000ff0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
1 squashfs-split partitions found on MTD device rootfs
0x000000360000-0x000000ff0000 : "rootfs_data"
0x000000ff0000-0x000001000000 : "radiocfg"
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38155
- append the root squashfs directly after the kernel,
- use the 64kraw/128kraw template instead of the 64k/128k,
- ensure that the generated images have enough erase blocks
for JFFS2 garbage collection,
Tested on WZR-HP-G300NH and WZR-600DHP boards.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38153
The Image/Build/WZRHP64K and the Image/Build/WZRHP128K macros
are similar. Move the common stuff into the Image/Build/WZRHP
macro and update the orignal macros to use that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38152
- append the root squashfs directly after the kernel,
- use the 64kraw template instead of the 64k,
- ensure that the generated images have enough erase blocks
for JFFS2 garbage collection,
Tested on a TEW-673GRU board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38151
The Image/Build/DIR825B1 and the Image/Build/DLRTDEV macros
are identical. Merge those into a new Image/Build/CameoAP94
macro, and update the device profiles to use the new macro.
Also rename the dir825b1_* mtdlayout macros to cameo_ap94_*.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38150
- append the root squashfs directly after the kernel,
- use the 64kraw template instead of the 64k,
- ensure that the generated images have enough erase blocks
for JFFS2 garbage collection,
Tested on a WispStation M5 board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38148
The firmware generation part is the same for both
macros. Move that into a separate macro and use the
new macro for Image/Build/UB{NTXM,DEV}.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38146
- append the root squashfs directly after the kernel,
- use the 64kraw template instead of the 64k
- ensure that the generated images have enough erase blocks
for JFFS2 garbage collection,
Tested on the WHR-G301N board only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38141
- remove the 'kernel' and 'rootfs' partitions from the mtd layout,
- move the .okli image into the uImage,
- append the root squashfs directly after the kernel,
- use the 64kraw template instead of the 64k
- ensure that the generated images have enough erase blocks
for JFFS2 garbage collection,
Tested on the MZK-W300NH board only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38139
- append the root squashfs directly to the kernel,
- use the 64kraw-nojffs template instead of sqashfs-only
- ensure that the generated images have enough erase blocks
for JFFS2 garbage collection,
Tested on a TEW-712BR devices only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38130
- append the root squashfs directly to the kernel,
- use the 64kraw/64kraw-nojffs template instead of 64k/squashfs-only,
- ensure, that the signature is placed at the correct offset in
the *-factory images,
- ensure that the generated images have enough erase blocks
for JFFS2 garbage collection,
Tested on DIR-600-A1 and TEW-632BR devices only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38129
The MTD layout of the AP99 based devices is different.
Add new macros to reflect that and use the new macros
for the DIR-615-E4 board.
This prevents overwriting of the 'mac' partition which
contain vital informations. The disadvantage of the change
is that the usable space is reduced by 192KiB. Blame the
vendors for the unfriendly partition layout.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38128
Also remove the similar code from the Netgear
profile and use the new feature instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38126
- remove the kernel and rootfs partitions from the mtd layout,
the kernel creates those automatically,
- remove estimation step, it is not needed anymore
- put the root squashfs directly after the kernel
- use the 64kraw template
With the default configuration, this allows to use more space for
rootfs_data with 64KiB. Tested on WNDR3700 v1 only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38120
The new macro will be used to determine the firmware
partition size from an MTD layout.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38117
Enable the wlan2g led in the default configuration of dir-825-c1.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Patchwork: http://patchwork.openwrt.org/patch/4079/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38106
This patch
- changes the color names from orange to amber
- changes the name of GPIO 13 from WIFI_BGN (wifi_bgn) to WLAN_2G
(wlan2g) to be more consistent with the other routers' files
- changes the descriptions of the hardware keys to be a tad more
explicit
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Patchwork: http://patchwork.openwrt.org/patch/4081/
[juhosg: update the LED migration script as well]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38105
Enable GPIO 20. This hands off control of the blue planet led to the
integrated switch. Consequently, remove the led configuration for the
blue planet led.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Patchwork: http://patchwork.openwrt.org/patch/4080/
[juhosg: whitespace fixup]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38096
This allows to build images for other boards, even if
the image is too big for Cameo devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38095
This patches fixes the lan led configuration. The new configuration is
identical to the one in mach-db120.c and it works. The previous one
didn't work at all.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38094
The goal is to set the WAN MAC address to the one on the
sticker on the bottom of the unit. Currently it is not
used at all. But some users expect the WAN interface to
have the MAC address that is written on the sticker.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38091
Rename the function and extend it in order to make it
usable from board setup code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38085
Change some flow-level unctions to return with an
error code in order to be able to report errors
to the core code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38068
This patch adds support for TP-Link TL-MR13U router with built-in 10AH
rechargeable battery.
The patch is based on kamwanlai's patch:
https://forum.openwrt.org/viewtopic.php?pid=206746#p206746
Updated to accommodate recent changes introduced with:
ar71xx: remove fs_* variables from image/Makefile
Signed-off-by: Oleg Titov <oleg.titov@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4063/
[juhosg:
- refresh and rename rename 930-add-tl-mr13u-support.patch =>
625-MIPS-ath79-add-tl-mr13u-support.patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38063
This patch adds OpenWRT support for the Netgear WNR2200 (N300)
wireless router with USB.
Technical details of this router can be found at
http://www.netgear.com/home/products/wirelessrouters/work-and-play/WNR2200.aspx
and http://wikidevi.com/wiki/Netgear_WNR2200
Signed-off-by: Aidan Kissane <aidankissane@googlemail.com>
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4055/
[juhosg:
- add commit message and SoB line from the original patch
- remove dead code from mach-wnr2200.c
- refresh 624-MIPS-ath79-WNR2200-support.patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38059
Add a new kernel config option for generic firmware partition
split support and change the uImage split support to depend on
the new option. Aslo rename the MTD_UIMAGE_SPLIT_NAME option to
MTD_SPLIT_FIRMWARE_NAME to make it more generic.
The patch is in preparation for multiple firmware format
support.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38002
This patch adds support for building firmware images for the
TP-Link TL-MR3040 v2. Tested and working on v2.1 hardware.
Signed-off-by: Mads Hansen <d@taba.se>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37964
I checked the GPL code drop from D-Link and tried to get the wireless
and LAN switch LEDs to light up. I found some references in
AthSDK/www/DIR-825_C1/bsp.h as well as
AthSDK/www/DIR-825_C1/rootfs/etc/sysconfig/S2gpio.sh, but in the end I
only got the led for 2.4GHz to work. Anyway, here's the patch.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37963
When the squashfs and jffs2 images are generated
in the same turn, the compressed kernel images
are generated twice with the same parameters.
Move compressed kernel generation into a separate
phase to avoid that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37881
Those are not needed since we are generating the
initramfs images along with the others.
Remove the variables and use the template names
directly.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37876
Initramfs images are not generated for profiles which
are using the squashfs-only template. Add the missing
'Image/Build/Template/squashfs-only/initramfs' to fix
that.
Also, 'Image/Build/Cameo933x/initramfs' uses wrong
parameters for 'MkuImageLzma/initramfs' due to a
misplaced commma. Remove that to fix the generated
initramfs images.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37871
Apparently registering usb device on newest trunk causes
this AP not to boot...
Since there is no USB socket in that device anyway this
can be simply removed (and device boots then no problem).
[juhosg:
- tweak subject line and description,
- remove #include "dev-usb.h",
- remove 'select ATH79_DEV_USB' from Kconfig]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37844
Based on the original firmware, the file must have the tag
HORNET-PACKET-DIR505A1-3, not HORNET-RT-DIR505A1-3.
http://patchwork.openwrt.org/patch/3945/
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 37781
This patch fixes the code of the buttons for TP-Link WA901ND.
Signed-off-by: Rocco Folino <lordzen@autistici.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37696
Small router sold in EU: AR9330@400MHz, 1x USB2.0,
2x ethernet, 8MB flash, 32MB ram, one led, one button.
See: http://galeria.tech-blog.pl/TP-Link_TL-WR710N-EU/
[juhosg: use a separate kernel patch]
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3873/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37572
Mercury MW4530R is a TP-Link TL-WDR4310 clone but
with a much lower price tag (~ $40). This patch
is tested to work at trunk r37525.
Signed-off-by: Leon Xu <ylxu72@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3856/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37571
Mercury MW4530R is a TP-Link TL-WDR4310 clone but
with a much lower price tag (~ $40). This patch
is tested to work at trunk r37525.
Signed-off-by: Leon Xu <ylxu72@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3856/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37570
Looks like trunk@37090 has changed the logic that determines
if router's button was pressed. This resulted in TEW632BRP
always booting into failsafe mode because it detected pressed
button (which was not pressed).
Measure with voltmeter has shown that buttons on this router
are actually active-low. This patch reflects this fact in
board configuration and fixes 'load info failsafe mode' issue.
Note: it looks like Trendnet TEW632BRP and a close relative
to TEW-652BRP V1.0 and D-Link DIR-615C1, so same problem may
exist on those routers as well. This patch doesn't affect
routers other than 632BRP and unfortunately I do not have
hardware to test this issue with other routers.
This patch fixes#13893 and is tested on actuall Trendnet
TEW632BRP.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37569
Create a separate board profile and update the profile
name in image/makefile. Also use the correct machtype
string in kernel command line.
Based on andelf's patch:
http://andelf.diandian.com/post/2013-05-22/40050677370
Signed-off-by: Oleg Titov <oleg.titov@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3840/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37550
This reverts r37477. A generic patch is used to fix
this globally, so revert the ar71xx specific change.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37480
Drop the local get_mtd_part_size implementation and use
the equivalent function provided by lib/functions.sh.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37476
TL-WR941N v6 use almost same IC as WDR3500.
[juhosg: change subject, and change fw layout from 4M to 4Mlzma]
Patchwork: http://patchwork.openwrt.org/patch/3719/
Signed-off-by: ShuYu Wang <andelf@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37471
switch buttons should be declared as switch so the failsafe shell is not
triggered by accident in procd
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 37131
In order to support both normal images and initramfs, ensure that each
target sets KERNELNAME properly so that the generic kernel building code
can copy the corresponding files over $(KDIR) with the appropriate
extension. Update the various paths to the kernel and wrapper images
from $(LINUX_DIR)/arch/$(ARCH)/boot/$(foo) to $(KDIR)/$(foo).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 37049
The TP-LINK TL-MR3220 v2 has a button on the left side
labeled "WIFI". This is GPIO 24. This patch adds the
support for this button.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36848
The port 6 of the switch is connected to the SFP
cage on the RB2011*S boards. Add a helper function
to correctly initialize the switch configuration
data on those boards to make the SFP port usable.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36799
