though, ata-dwc is built-in on the target already.
Fixes: fd9dc10530 ("apm821xx: make ata-dwc as a standalone module")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
module is only useful for apm821xx targets, so
limit visability to just this target.
Fixes: 55fbcad20a ("apm821xx: make crypto4xx as a standalone module")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Make the crypto4xx crypto accelerator support as a standalone module.
This saves 90kb on a gzipped kernel.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
In order to cut down on the Netgear WNDR4700, the ata
driver can be outsourced. This helps other apm821xx
devices too to save up on kernel size (~200 kb).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
it was reported that this flag caused the mx60
not to boot anymore.
Fixes: f095822699 ("apm821xx: convert legacy nand partition layou")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
specify that this functions adds a Cisco Meraki
special-sauce header for their custom loader/uboot.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
All targets are bumped to 5.15. Remove the old 5.10 patches, configs
and files using:
find target/linux -iname '*-5.10' -exec rm -r {} \;
Further, remove the 5.10 include.
Signed-off-by: Nick Hainke <vincent@systemli.org>
libdeflate's gzip compressor provides a better
compression ratio and uboot's decompressor has
no problem with the data streams.
Tested on MX60, WNDR4700, WNDAP660
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Manually rebased:
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
[Move gro_skip in 680-NET-skip-GRO-for-foreign-MAC-addresses.patch to old position]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
use the toolchain's default CPU (464fp) as the CPU option.
This fixes a CPU selection prompt which shows up now.
CPU selection
> 1. Generic 32 bits powerpc (POWERPC_CPU) (NEW)
2. Rely on the toolchain's implicit default CPU (TOOLCHAIN_DEFAULT_CPU) (NEW)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
All targets expect the malta target already activate the CONFIG_GPIOLIB
option. Move it to generic kernel configuration and also activate it for
malta.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tim Small reported:
| Viewing the 'Network' -> 'Switch' config page in LuCI:
|
| The LuCI LAN 1 port corresponds to the port physically
| labelled 2 at the rear of the device.
| [...]
|
| When a patch cord is attached to the port labelled 1 [...],
| the LED labelled 2 illuminates. [...]
=> Ports, LuCI and LEDs are reversed/don't match.
Reported-by: Tim Small
Fixes: #10111
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This is now built-in, enable so it won't propagate on target configs.
Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca9367069 ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
As per the series:
<https://www.spinics.net/lists/devicetree/msg508906.html>
"Enforce specific naming pattern for children (keys) to narrow the
pattern thus do not match other properties. This will require all
children to be properly prefixed or suffixed (button, event, switch
or key)."
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The MBL has a 512KiB Microchip SST39VF040 chip for uboot and
not much else.
Thanks to Ewald who figured out that the "jedec-probe" vs.
"jedec-flash" was the wrong binding. With this information
and the jedec-probe support enabled => the chip works.
| physmap-flash 4fff80000.nor_flash: physmap platform flash device: [mem 0x4fff80000-0x4ffffffff]
| Found: SST 39LF040
| 4fff80000.nor_flash: Found 1 x8 devices at 0x0 in 8-bit bank
Suggested-by: Ewald Comhaire <e.comhaire@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This makes it possible to fix Netgear WNDAP620+660 DTS ugliness.
Bring back the dtb and firmware partitions for the WNDR4700.
Thank you, mans0n.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch copies over refreshed config and patches from 5.10
with the following changes:
- dropped superfluous tc654/tc655 variant detection patch
(tc654 support will become available upstream starting with
5.17-rc7+).
- dropped xhci msi(x) workaround... as the broken MSI(X)
is now gone.
- dropped dwc2 workaround since the driver was fixed and it
works without it.
Please note: Netgear WNDAP660 & WNDAP620 users:
Due to the kernel's size increase, uboot will likely break
because it is overwrite the kernel during decompression.
To fix this (and debrick affected devices, no reflash
necessary), attach the RJ45-Serial-Console cable and
enter the following in the uboot prompt during bootup:
setenv kernel_addr_r 1100000
saveenv
run bootcmd
to restore the old/previous behavior:
setenv kernel_addr_r 600000
saveenv
run bootcmd
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Upstream hwmon-maintainer had various comments about
the changes to the tc654 driver. These have been
addressed and the cooling device support is destined
for inclusion.
One of the comments was the change of the cooling states
scaling. No longer the driver uses the same values as the
hwmon interface, instead the states are now the 17 states
the tc654 supports.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
with the introduction of the DEVICE_ALTX_VENDOR, DEVICE_ALTX_MODEL
multiple/sibiling devices can seemingly supported by one device entry.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
the WNDR4700 can fetch its calibration data and
mac-addresses directly from the "wifi_data" partition.
This allows us to get rid of the 10-ath9k-eeprom file
for the apm821xx target completely.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
in order to get nvmem-cells to work on AP and routers
(Netgears WNDR4700). The nvmem-cell needs to be within
a fixed-partition dt-node.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Add and enable a new kconfig knob to disable unprivileged eBPF by default.
Patches automatically rebased.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
These never worked and upstream is in the process of removing
them as well. Legacy PCI interrupt signaling is still working
as before.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Apart from the dtb partition, these were all "read-only;"
they serve no purpose other than being a copy of what
netgear had defined in their original firmware.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
where to begin? the USB regulator settings were just
a part of the issue. With them changed, according to
the forum it still failed when a USB device was
connected to the port with:
dwc2 4bff80000.usbotg: dwc2_restore_global_registers: no global registers to restore
dwc2 4bff80000.usbotg: dwc2_exit_partial_power_down: failed to restore registers
dwc2 4bff80000.usbotg: exit partial_power_down failed
dwc2 4bff80000.usbotg: HC died; cleaning up
One clue was found upstream in
commit cc10ce0c51b1 ("usb: dwc2: disable power_down on Amlogic devices")
|Disable power_down by setting the parameter to
|DWC2_POWER_DOWN_PARAM_NONE. This fixes a problem on various Amlogic
|Meson SoCs where USB devices are only recognized when plugged in before
|booting Linux. A hot-plugged USB device was not detected even though the
|device got power (my USB thumb drive for example has an LED which lit
|up).
|[...]
the same method proposed there worked with APM821xx's USB IP-Core.
Link: https://forum.openwrt.org/t/wd-my-book-duo-usb/111926/2
Reported-by: thwe and takimata (openwrt forum)
Fixes: b70d3557e0 ("apm821xx: clean up gpio-hogs")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
