Commit Graph

22887 Commits

Author SHA1 Message Date
Álvaro Fernández Rojas
edafbe81e0 bcm63xx: bcm6328-leds: improve HW blinking
Add support for second HW blinking interval.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-19 11:03:58 +02:00
Álvaro Fernández Rojas
daee6b4661 bcm63xx: add Comtrend VG-8050 support
BCM63169 with 128M RAM, 128M NAND and BCM53125 switch.
Switch is connected by HSSPI to CS5.
More info: https://openwrt.org/toh/comtrend/vg8050

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-19 10:41:47 +02:00
Álvaro Fernández Rojas
62e7342ddf bcm63xx: add NETGEAR DGND3700v2 support
BCM6362 with 64M RAM, 32M NAND and BCM53125 switch.
Switch is connected by MMAP, which is currently unsupported (no VLANs).
More info: https://openwrt.org/toh/netgear/dgnd3700v2

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-19 10:41:42 +02:00
Adrian Schmutzler
74ff0773b5 ramips: remove leading zeros from MAC address location
Cosmetic adjustment to match the rest of the target.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 21:51:06 +02:00
Adrian Schmutzler
be9eab9bca ramips: set WAN address in DTS for ASUS RT-AC51U/RT-AC54U
The location 0x28 in factory partition is the common one used for
ethernet address on this architecture. Despite, it contains the label
MAC address for the devices at hand.

Consequently, this patch moves 0x28 to the &ethernet node in DTS files
(setting the WAN MAC address there) and sets up the lan_mac from 0x22
in 02_network. As a benefit, this allows to use label-mac-device in
DTS instead of ucidef_set_label_macaddr.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 21:51:06 +02:00
Adrian Schmutzler
a1f0fd8cba ramips: use DT trigger for 2G WiFi on ASUS RT-AC51U
Like for the RT-AC54U, this uses a DT trigger for WiFi also at the
RT-AC51U. While at it, rename node and label to wifi2g.

Note that the 5g WiFi LED still isn't supported (see PR #3017 for
further details: https://github.com/openwrt/openwrt/pull/3017 )

Tested-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 21:51:06 +02:00
Adrian Schmutzler
0b34a36da9 ramips: fix MAC address assignment for ASUS RT-AC51U
The current MAC address assignment for the ASUS RT-AC51U is "wrong",
it actually should be the same as for the RT-AC54U. Fix it.

MAC assignment based on vendor firmware:

  2g    0x4	label
  5g    0x8004	label +4
  lan   0x22	label +4
  wan   0x28	label

Thanks to Davide Fioravanti for checking this on his device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 21:51:06 +02:00
Fabian Bläse
33b2078528 mt7621: Make ER-X-SFP factory image compatible with EP-R6
The version inside the compat file determines, if a firmware supports
a specific device. I have not yet fully understood, how this is checked,
but it only seems to indicate which devices are supported by a specific
version of the combined vendor firmware. Devices assume that subsequent
versions, starting with the version that initially added support for a
specific device, are always compatible.

The first compat version that added support for the EP-R6 was '21001:7',
but OpenWrt did use '21001:6' before. This is why the factory image could
not be flashed using the vendor software, but only using TFTP.

The compat version has been bumped by the vendor a few times, but more
devices have been added since (e.g. ER-10X). Because OpenWrt currently
only supports the ER-X, ER-X-SFP and EP-R6, the compat version is
incremented to the version that first supported the EP-R6, which is
'21001:7'.

This allows the factory image to be flashed on EP-R6 without TFTP.

Signed-off-by: Fabian Bläse <fabian@blaese.de>
2020-05-18 21:11:47 +02:00
David Bauer
4133304413 mpc85xx: restructure image receipts
Move the image receipts into separate per-subtarget files like it is
done on most other targets.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-05-18 21:11:39 +02:00
David Bauer
564f87ef5b mpc85xx: rename generic subtarget to p1010
The mpc85xx-generic subtarget supports the QorIQ SoCs of the p1010
family. Rename the subtarget to reflect this affiliation as it's the
case with the other mpc85xx subtargets.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-05-18 21:11:22 +02:00
Álvaro Fernández Rojas
367a30389d bcm63xx: add support for Comtrend VR-3032u
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-18 18:24:06 +02:00
Álvaro Fernández Rojas
86583384ff bcm63xx: smp: add NAND support
NAND controller is present on BCM6328, BCM6362, BCM6368 and BCM63268.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-18 18:24:06 +02:00
Álvaro Fernández Rojas
cca13d8e82 kernel: mtdsplit: add BCM WFI support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-18 18:24:06 +02:00
Adrian Schmutzler
4a61a88f90 ath79: add support for TP-Link TL-WA901ND v4 and v5
This ports support for the TL-WA901ND v4 and v5 from ar71xx to ath79.
They are similar to the TP9343-based TL-WR940N v3/v4 and TL-WR941ND v6.

Specifications:
  SoC: TP9343
  Flash/RAM: 4/32 MiB
  CPU: 750 MHz
  WiFi: 2.4 GHz b/g/n
  Ethernet: 1 port (100M)

Flashing instructions:
  Upload the factory image via the vendor firmware upgrade option.

Flash instruction (TFTP):
  1. Set PC to fixed ip address 192.168.0.66
  2. Download *-factory.bin image and rename it to * (see below)
  3. Start a tftp server with the image file in its root directory
  4. Turn off the router
  5. Press and hold Reset button
  6. Turn on router with the reset button pressed and wait ~15 seconds
  7. Release the reset button and after a short time
     the firmware should be transferred from the tftp server
  8. Wait ~30 second to complete recovery.

  * The image name for TFTP recovery is wa901ndv4_tp_recovery.bin for
  both variants.

In ar71xx, a MAC address with offset 1 was used for ethernet port.
That's probably wrong, but this commit sticks to it until we know
the correct value.

Like in ar71xx, this builds the default factory.bin with EU country
code.

Thanks to Leonardo Weiss for testing on the v5.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 13:35:38 +02:00
Alexander Couzens
bf5d800578
lantiq: fritz 7360 v2: remove additional supported devices
The additional supported device isn't required since this is a new
device. Some board contains an addtional device,
those device were supported in earlier versions which used the
"old" image builder code.
To support an sysupgrade from such old version, there is the all caps
additional device.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 11:59:22 +02:00
Alexander Couzens
0962baae4e lantiq: fritz 7360 v2: rename device before it will be used
Use similiar naming scheme as ath79.
Since the fritz 7360 v2 was only in the tree for 2 days, there
is no compatibility for the old image.
Users which has installed the fritz 7360 v2 before this change, must
use sysupgrade --force to skip checks on the board.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 11:57:57 +02:00
Adrian Schmutzler
30cc7f3510 ramips: increase SPI frequency for ASUS RT-AC51U/RT-AC54U
This increases the SPI frequency for both ASUS RT-AC51U and RT-AC54U.

Speed comparison tests have been performed on RT-AC54U:

- 10Mhz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real    4m 37.78s
user    0m 0.02s
sys     2m 43.92s

- 50Mhz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real    1m 28.34s
user    0m 0.03s
sys     0m 46.96s

- 50Mhz fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real    1m 11.94s
user    0m 0.01s
sys     0m 46.94s

- 80Mhz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real    1m 12.31s
user    0m 0.04s
sys     0m 46.96s

- 80Mhz fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real    1m 12.15s
user    0m 0.02s
sys     0m 46.97s

Based on that, we took 50 MHz with fast-read, as higher frequencies
didn't yield further improvements.

For the RT-AC51U, only the final configuration was tested.

Tested-by: Zhijun You <hujy652@gmail.com> [RT-AC54U]
Tested-by: Davide Fioravanti <pantanastyle@gmail.com> [RT-AC51U]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 11:38:22 +02:00
Álvaro Fernández Rojas
13c33f3f12 bcm63xx: mask interrupts on init
Fixes BCM6348/BCM6358 hangs while booting:
https://bugs.openwrt.org/index.php?do=details&task_id=2202

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-17 23:29:48 +02:00
Roger Pueyo Centelles
a0ef42e77c ath79: add support for Ubiquiti PowerBeam 5AC 500
The Ubiquiti PowerBeam 5AC 500 (PBE-5AC-500) is an outdoor 802.11ac
5 GHz bridge with a radio feed and a dish antenna.

Specifications:
 - SoC: Qualcomm Atheros QCA9558
 - RAM: 128 MB DDR2
 - Flash: 16 MB SPI NOR (mx25l12805d)
 - Ethernet: 1x 10/100/1000 Mbps Atheros 8031, 24 Vdc PoE-in
 - WiFi 5 GHz: QCA988x HW2.0 Ubiquiti target 0x4100016c chip_id 0x043222ff
 - Buttons: 1x (reset)
 - LEDs: 1x power, 1x Ethernet, 4x RSSI, all blue
 - UART: not tested

Not supported:
 - RSSI LEDs (probably through 74HC595 chip)

Installation from stock airOS firmware:
 - Follow instructions for XC-type Ubiquiti devices on OpenWrt wiki at
   https://openwrt.org/toh/ubiquiti/common

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2020-05-17 21:03:30 +02:00
Davide Fioravanti
31b49f02ca ramips: add support for Linksys EA7500 v2
The Linksys EA7500 v2 is advertised as AC1900, but its internal
hardware is AC2600 capable.

Hardware
--------
SoC:   Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM:   256M (Nanya NT5CC128M16IP-DI)
FLASH: 128MB NAND (Macronix MX30LF1G18AC-TI)
ETH:   5x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
  - 2.4GHz: 1x MT7615N (4x4:4)
  - 5GHz:   1x MT7615N (4x4:4)
  - 4 antennas: 3 external detachable antennas and 1 internal
USB:
  - 1x USB 3.0
  - 1x USB 2.0
BTN:
  - 1x Reset button
  - 1x WPS button
LEDS:
  - 1x White led (Power)
  - 6x Green leds (link lan1-lan4, link wan, wps)
  - 5x Orange leds (act lan1-lan4, act wan) (working but unmodifiable)

Everything works correctly.

Installation
------------
The “factory” openwrt image can be flashed directly from OEM stock
firmware. After the flash the router will reboot automatically.

However, due to the dual boot system, the first installation could fail
(if you want to know why, read the footnotes).
If the flash succeed and you can reach OpenWrt through the web
interface or ssh, you are done.
Otherwise the router will try to boot 3 times and then will
automatically boot the OEM firmware (don’t turn off the router.
Simply wait and try to reach the router through the web interface
every now and then, it will take few minutes).

After this, you should be back in the OEM firmware.

Now you have to flash the OEM Firmware over itself using the OEM web
interface (I tested it using the FW_EA7500v2_2.0.8.194281_prod.img
downloaded from the Linksys website).

When the router reboots flash the “factory” OpenWrt image and this
time it should work.

After the OpenWrt installation you have to use the sysupgrade image
for future updates.

Restore OEM Firmware
--------------------
After the OpenWrt flash, the OEM firmware is still stored in the
second partition thanks to the dual boot system.
You can switch from OpenWrt to OEM firmware and vice-versa failing
the boot 3 times in a row:
 1) power on the router
 2) wait 15 seconds
 3) power off the router
 4) repeat steps 1-2-3 twice more.
 5) power on the router and you should be in the “other” firmware

If you want to completely remove OpenWrt from your router, switch to
the OEM firmware and then flash OEM firmware from the web interface
as a normal update.
This procedure will overwrite the OpenWrt partition.

Footnotes
---------
The Linksys EA7500-v2 has a dual boot system to avoid bricks.
This system works using 2 pair of partitions:
 1) "kernel" and "rootfs"
 2) "alt_kernel" and "alt_rootfs".
After 3 failed boot attempts, the bootloader tries to boot the other
pair of partitions and so on.

This system is managed by the bootloader, which writes a bootcount in
the s_env partition, and if successfully booted, the system add a
"zero-bootcount" after the previous value.

A system update performed from OEM firmware, writes the firmware on the
other pair of partitions and sets the bootloader to boot the new pair
of partitions editing the “boot_part” variable in the bootloader vars.
Effectively it's a quick and safe system to switch the selected boot
partition.

Another way to switch the boot partition is:
 1) power on the router
 2) wait 15 seconds
 3) power off the router
 4) repeat steps 1-2-3 twice more.
 5) power on the router and you should be in the “other” firmware

In this OpenWrt port, this dual boot system is partially working
because the bootloader sets the right rootfs partition in the cmdline
but unfortunately OpenWrt for ramips platform overwrites the cmdline
so is not possible to detect the right rootfs partition.

Because all of this, I preferred to simply use the first pair of
partitions and set read-only the other pair.

However this solution is not optimal because is not possible to know
without opening the case which is the current booted partition.
Let’s take for example a router booting the OEM firmware from the first
pair of partitions. If we flash the OpenWrt image, it will be written
on the second pair. In this situation the router will bootloop 3 times
and then will automatically come back to the first pair of partitions
containg the OEM firmware.
In this situation, to flash OpenWrt correctly is necessary to switch
the booting partition, flashing again the OEM firmware over itself.
At this point the OEM firmware is on both pair of partitions but the
current booted pair is the second one.
Now, flashing the OpenWrt factory image will write the firmware on
the first pair and then will boot correctly.

If this limitation in the ramips platform about the cmdline will be
fixed, the dual boot system can also be implemented in OpenWrt with
almost no effort.

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Co-Developed-by: Jackson Lim <jackcolentern@gmail.com>
Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
2020-05-17 18:44:28 +02:00
Sungbo Eo
a4e9c8f14b ramips: add support for netis WF2770
netis WF2770 is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.

Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7610EN
- Ethernet: 5x 10/100/1000Mbps
  - Switch: MT7530BU
- UART:
  - J2: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1

MAC addresses in factory partition:
0x0004: LAN, WiFi 2.4GHz (label_mac-6)
0x0028: not used (label_mac-1)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac+2)

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-05-17 18:41:48 +02:00
Zhijun You
46674723e1 ramips: add support for ASUS RT-AC54U
Specification:

- CPU: MTK MT7620A
- RAM: 64MB
- ROM: 16MB SPI Flash Macronix MX25L12835E
- WiFi1: MediaTek MT7620A
- WiFi2: MediaTek MT7612E
- Button: reset, wps
- LED: 9 LEDs:Power, WiFi 2.4G,WiFi 5G, USB, LAN1, LAN2, LAN3, LAN4, WAN
- Ethernet: 5 ports, 4 LAN + 1 WAN
- Other: 1x UART 1x USB2.0

Installation:

   Update using ASUS Firmware Restoration Tool:

1. Download the ASUS Firmware Restoration Tool but don't open it yet
2. Unplug your computer from the router
3. Put the router into Rescue Mode by: turning the power off, using a pin
   to press and hold the reset button, then turning the router back on while
   keeping the reset button pressed for ~5 secs until the power LED starts
   flashing slowly (which indicates the router has entered Rescue Mode)
4. Important (if you don't do this next step the Asus Firmware
   Restoration Tool will wrongly assume that the router is not in Rescue Mode
   and will refuse to flash it): go to the Windows Control Panel and
   temporarily disable ALL other network adapters except the one you will use
   to connect your computer to the router
5. For the single adapter you left enabled, temporarily give it the
   static IP 192.168.1.10 and the subnet mask 255.255.255.0
6. Connect a LAN cable between your computer (make sure to use the
   Ethernet port of the adapter you've just set up) and port 1 of the router
   (not the router's WAN port)
7. Rename sysupgrade.bin to factory.trx
8. Open the Asus Firmware Restoration Tool, locate factory.trx and click
   upload (if Windows shows a compatibility prompt, confirm that the tool worked fine)
9. Flashing and reboot is finished when the power LED stops blinking and
   stays on

MAC assignment based on vendor firmware:

2g    0x4	label
5g    0x8004	label +4
lan   0x22	label +4
wan   0x28	label

Signed-off-by: Zhijun You <hujy652@gmail.com>
[rebased due to DTSI patch, minor commit message adjustments, fix
label MAC address (lan->wan), do spi frequency increase separately]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:40:56 +02:00
Adrian Schmutzler
685cc66c2a ramips: create DTSI for ASUS RT-AC51U and RT-AC54U
This creates a DTSI for the ASUS RT-AC51U and the upcoming RT-AC54U,
as they are quite similar.

White at it, drop the unneeded "status = okay" for ethernet.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:39:48 +02:00
Adrian Schmutzler
b24fd13024 lantiq: drop outdated kernel version switches from patches-5.4
This drops some ancient kernel version switches from patches on
lantiq target. The patch only adjusts the latest kernel 5.4, as
doing it a second time for an older kernel seems a waste of time
for a cosmetic change.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:36:21 +02:00
Adrian Schmutzler
41b5ca1458 bcm27xx: drop outdated kernel version switches from patches-5.4
This drops some ancient kernel version switches from patches on
bcm27xx target. The patch only adjusts the latest kernel 5.4, as
doing it a second time for an older kernel seems a waste of time
for a cosmetic change.

Refresh remaining target patches.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:36:10 +02:00
Adrian Schmutzler
8ff813e5f4 generic: drop outdated kernel version switches in local drivers
This drops the obsolete version switches for non-supported kernels
from local drivers in generic target.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:35:59 +02:00
Adrian Schmutzler
c00b2df6c8 ramips: drop non-existant ralink,port-map for Ravpower WD03
The property "ralink,port-map" has been obsolete long before
this device was added, and the device is a one-port anyway.
Just remove it.

Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:34:40 +02:00
Adrian Schmutzler
d7a28e8ed2 ramips: mt7620: tidy up ethernet node in DTS files
This tidies up the ethernet node in mt7620 DTS files by:

- removing unnecessary status as it is not disabled
- reordering properties consistently
- adding empty lines to enhance readability

This should make comparison and reviewing new PRs based on C/P easier.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:28:03 +02:00
Thibaut VARÈNE
2ea481193c generic: platform/mikrotik: fix LZOR support
31e99fe3da which introduced this code was unfortunately untested.
This commit fixes a number of issues and works around the fact that in
this particular scheme, the LZO payload may be padded at the end which
will trigger a harmless lzo decompression error.
This commit also disambiguates the debug printks.

Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Fixes: 31e99fe3da ("generic: platform/mikrotik: support LZOR encoding")
2020-05-16 20:30:46 +02:00
Yushi Nishida
78bebe680f
lantiq/xrx200: add support for the Fritzbox 7360v2
This commit adds support for the Fritzbox 7360v2

CPU: VR9 500MHz Cores: 2
RAM: 128 MB
NOR-Flash: 32 MB
WLAN: AR9287-BL1A

DECT is not working.

Thanks Sebastian Ortwein for adding 7360SL.
The dts file is derived from avm_fritz7360sl.dts.

Firmware can be flashed with this method:

1.) Set your client IP to 192.168.178.2
2.) Power on your your Fritzbox and connect to 192.168.178.1
    via ftp in the first 5 seconds.
3.) login with adam2/adam2
4.) type into the ftp prompt:

passive
binary
debug 1
quote MEDIA FLSH // (not FLASH)
put openwrt-lantiq-xrx200-avm_fritz7360v2-squashfs-sysupgrade.bin mtd1
// using the correct location for the squashfs-sysupgrade-firmware.bin

5.) wait till red light flashing turns off.
6.) type: exit

Run tested with kernel 4.19 and 5.4 on Fritzbox 7360 V2.

Issue:
Ethernet speed is slow, (iperf between a Xiaomi mir3g
and this router results in <80Mbits throughput
with a wired cable when using the gbit ports.)

Signed-off-by: Yushi Nishida <kyro2man@gmx.net>
2020-05-16 04:37:55 +02:00
Aleksander Jan Bajkowski
2f7118712e ath79: increase spi frequency on tp-link tl-wr1043nd v2
Increase SPI frequency to 33.333 MHz. It's maximum frequency supported
by SPI Flash memory chip without Fast read opcode.

Before:
$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real	0m 3.21s
user	0m 0.00s
sys	0m 3.21s

After:
$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real	0m 2.52s
user	0m 0.00s
sys	0m 2.52s

Tested on TP-Link TL-WR1043ND V2.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-05-15 10:00:32 +08:00
Daniel Gonzalez Cabanelas
e04ff3c7cc bcm63xx: periph_intc: report effective affinity
The bcm6345-periph-intc driver only targets a single CPU at a time, even
if the notional affinity is wider. Let's inform the core code about this.

This patch gets rid of the kernel message:
"genirq: irq_chip bcm6345-periph-intc did not update eff. affinity mask
of irq 52"

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
2020-05-14 18:10:12 +02:00
Álvaro Fernández Rojas
29c3bb5f41 bcm63xx: ext_intc: fix warning
In file included from ./arch/mips/include/asm/io.h:34,
                 from ./arch/mips/include/asm/mmiowb.h:5,
                 from ./include/linux/spinlock.h:60,
                 from ./include/linux/irq.h:14,
                 from drivers/irqchip/irq-bcm6345-ext.c:10:
drivers/irqchip/irq-bcm6345-ext.c: In function 'bcm6345_ext_intc_of_init':
./arch/mips/include/asm/mach-bcm63xx/ioremap.h:48:9: warning: 'base' may be used uninitialized in this function [-Wmaybe-uninitialized]
  return is_bcm63xx_internal_registers((unsigned long)addr);
         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/irqchip/irq-bcm6345-ext.c:255:16: note: 'base' was declared here
  void __iomem *base;
                ^~~~

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-14 16:28:31 +02:00
Álvaro Fernández Rojas
f2f2cf07a6 bcm63xx: periph_intc: fix warning
drivers/irqchip/irq-bcm6345-periph.c: In function 'bcm6345_periph_irq_handle':
drivers/irqchip/irq-bcm6345-periph.c:55:21: warning: 'block' may be used uninitialized in this function [-Wmaybe-uninitialized]
  struct intc_block *block;
                     ^~~~~

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-14 16:27:31 +02:00
Álvaro Fernández Rojas
f314cbe54b bcm63xx: redboot: fix warning
drivers/mtd/parsers/redboot.c: In function 'parse_redboot_partitions':
drivers/mtd/parsers/redboot.c:194:59: warning: suggest parentheses around '-' in operand of '&' [-Wparentheses]
     fis_origin = (buf[i].flash_base & (master->size << 1) - 1);
                                       ~~~~~~~~~~~~~~~~~~~~^~~

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-14 16:12:12 +02:00
Álvaro Fernández Rojas
ee6bf7e865 bcm63xx: bcm6362: fix pinctrl bug
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-14 16:12:12 +02:00
Álvaro Fernández Rojas
aa2f2276f7 bcm63xx: image: remove unused definition
KERNEL_ENTRY isn't used by lzma-loader.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-14 16:12:08 +02:00
Álvaro Fernández Rojas
eea23c2004 bcm63xx: remove linux 4.14 support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-14 14:52:54 +02:00
Koen Vandeputte
eb17ee294c kernel: bump 5.4 to 5.4.41
Refreshed all patches.

Compile-tested on: imx6
Runtime-tested on: imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-05-14 13:33:40 +02:00
Koen Vandeputte
d503492857 kernel: bump 4.19 to 4.19.123
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-05-14 13:33:40 +02:00
Adrian Schmutzler
2308644b0c ipq40xx: replace "ok" with "okay" for status in DTS files
While "ok" is recognized in DT parsing, only "okay" is actually
mentioned as valid value. Replace it accordingly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-12 19:16:41 +02:00
Adrian Schmutzler
fdd968d64e bcm63xx: replace "ok" with "okay" for status in DTS files
While "ok" is recognized in DT parsing, only "okay" is actually
mentioned as valid value. Replace it accordingly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-12 16:59:04 +02:00
Adrian Schmutzler
026fe1308c bcm63xx: use generic diag.sh
This commit removes the target-specific diag.sh script. This way, the
generic one is used for the target, which uses DT-aliases to specify the
LEDs used.

Though generic diag.sh allows to use different LEDs to indicate different
states, this patch just moves the old assignment and does not try to
"improve" the assignment by using additional colors.
However, individual proposals to do so are welcome.

For the few cases where status_led2 was used in old diag.sh, only the
primary LED was migrated.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-12 16:57:45 +02:00
Thibaut VARÈNE
96414047c9 ar71xx: mikrotik: mach-rbspi.c remove wlan id
Following on the previous commit, this patch removes useless id argument
from rbspi_wlan_init().

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-12 12:41:12 +02:00
Thibaut VARÈNE
1c6990fe6d ar71xx: mikrotik: bypass id check in __rb_get_wlan_data()
The id parameter in __rb_get_wlan_data() was incorrectly used on the
assumption that id "0" would always be tied to ath9k with RLE encoding
and positive id (in fact, only id "1" was valid) would always be tied to
("external") ath10k with LZO encoding.

Newer hardware revisions of supported devices prove this assumption to
be invalid, with ath9k caldata being now wrapped in MAGIC_ERD and LZO
compressed, so disable this check to allow newer hardware to correctly
decode caldata for ath9k. Since ath10k caldata is no longer pulled from
this implementation, this commit also disables the publication in sysfs
to avoid wasting memory.

Note: this patch assumes that ath9k caldata is never stored with the new
"LZOR" encoding scheme found on some ath10k devices.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-12 12:41:08 +02:00
Koen Vandeputte
0fed36dd48 kernel: bump 5.4 to 5.4.40
Refreshed all patches.

Compile-tested on: imx6
Runtime-tested on: imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-05-12 12:36:28 +02:00
Koen Vandeputte
7dd2d7289a kernel: bump 4.19 to 4.19.122
Refreshed all patches.

Remove upstreamed:
- 551-loop-Better-discard-support-for-block-devices.patch

Fixed:
- CVE-2020-11884
- CVE-2020-12114
- CVE-2019-3016
- CVE-2020-11669

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-05-12 12:36:28 +02:00
Koen Vandeputte
ef2d5a2ab4 kernel: bump 4.14 to 4.14.180
Refreshed all patches.

Fixes:
- CVE-2020-12114
- CVE-2020-11669

Compile-tested on: pistachio
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-05-12 12:36:28 +02:00
Álvaro Fernández Rojas
a0081b1945 bcm63xx: loader-lzma: use default lzma
Specific CFE LZMA parameters aren't needed for LZMA Loader.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-12 12:34:57 +02:00
Álvaro Fernández Rojas
84646936a6 bcm63xx: image: rename LOADADDR to KERNEL_LOADADDR
Also remove KERNEL_ENTRY, since it's the same as KERNEL_LOADADDR

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-12 12:34:57 +02:00