Like in the previous patches for other targets, this will remove
the "devicename" from LED labels in lantiq.
The devicename is removed in DTS files and 01_leds, consolidation
of definitions into DTSI files is done where (easily) possible,
and migration scripts are updated. The DTS/DTSI consolidation is
only performed for files-5.4.
For lantiq,easy98020 some LED definitions have the form
"devicename:function" without the color, so we need to implement
explicit migration for that one.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This is the most popular choice in the linux kernel tree.
Within OpenWrt, this change will establish consistency with ath79
and ramips targets.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[extend commit message, include netgear_dm200, update base-files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Split the /etc/uci-defaults/01_led_migration scripts into subtargets
as already done for most of the other base-files.
While this introduces a minor amount of code duplication, it still
is considered an improvement, as device-specific settings are kept
together in the subtargets' base-files and the script at hand can be
removed entirely for two of the subtargets not needing it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Use similiar naming scheme as ath79.
Since the fritz 7360 v2 was only in the tree for 2 days, there
is no compatibility for the old image.
Users which has installed the fritz 7360 v2 before this change, must
use sysupgrade --force to skip checks on the board.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for the Fritzbox 7360v2
CPU: VR9 500MHz Cores: 2
RAM: 128 MB
NOR-Flash: 32 MB
WLAN: AR9287-BL1A
DECT is not working.
Thanks Sebastian Ortwein for adding 7360SL.
The dts file is derived from avm_fritz7360sl.dts.
Firmware can be flashed with this method:
1.) Set your client IP to 192.168.178.2
2.) Power on your your Fritzbox and connect to 192.168.178.1
via ftp in the first 5 seconds.
3.) login with adam2/adam2
4.) type into the ftp prompt:
passive
binary
debug 1
quote MEDIA FLSH // (not FLASH)
put openwrt-lantiq-xrx200-avm_fritz7360v2-squashfs-sysupgrade.bin mtd1
// using the correct location for the squashfs-sysupgrade-firmware.bin
5.) wait till red light flashing turns off.
6.) type: exit
Run tested with kernel 4.19 and 5.4 on Fritzbox 7360 V2.
Issue:
Ethernet speed is slow, (iperf between a Xiaomi mir3g
and this router results in <80Mbits throughput
with a wired cable when using the gbit ports.)
Signed-off-by: Yushi Nishida <kyro2man@gmx.net>
This reorganizes 02_network board.d files based on what's done for
ath79 and ramips: Instead of putting all settings into a single big
case, the interface/dsl/MAC address setup is put into separate
functions with a specific switch case for each of them. This makes
grouping of devices much easier and should be easier to read, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
DSL setup consists of the same commands for all subtargets, so move it
into a helper function.
While at it, remove shebang from library file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This splits the device-dependent base-files into subtarget directories,
like done recently for ath79 and ramips. While this increases the
overall lines of codes, it will make the code per subtarget smaller
and easier to keep track of features and devices.
While at it, several variables at the top of 02_network are removed,
as they were never changed. The values are put directly into the
function calls where they are used.
Remove unneeded LED setup from 01_leds, and remove 01_leds entirely
for falcon subtarget (as it is not used there).
Applies alphabetic reordering to device cases in base-files.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
