This adds support for the TP-Link TL-WR710N v2.1. It is basically a
re-issue of the v1.2.
Specifications:
SoC: Atheros AR9331
CPU: 400 MHz
Flash: 8 MiB
RAM: 32 MiB
WiFi: 2.4 GHz b/g/n
Ethernet: 2x 100M ports
USB: 1x 2.0
The only difference from the v1 is the TP-Link hardware ID/revision.
Attention:
The TL-WR710N v2.0 (!) has only 4 MB flash and cannot be flashed with
this image. It has a different TPLINK_HWREV, so accidental flashing
of the factory image should be impossible without additional measures.
Unfortunately, the v2.0 in ar71xx has the same board name, so sysupgrade
from ar71xx v2.0 into ath79 v1/v2.1 will not be prevented, but will brick
the device.
Flashing instruction:
Upload the factory image via the OEM firmware GUI upgrade mechanism.
Further notes:
To make implementation easier if somebody desires to port the 4M v2.0,
this already creates two DTSI files.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Fabian Eppig <fabian@eppig.de>
As described in commit commit 891a700759 ("lantiq: enable second VPE
on Fritz!Box 7412"):
The AVM Fritz!Box 7412 does not use the VMMC part of the Lantiq chip but
rather a proprietary solution based on the DECT chip for the FXS ports.
We can remove last traces of vmmc in dts.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Abort the dhcp-check based on the interface instead of the carrier
state. In cases where the interface is up but the carrier is down,
netifd won't cause a dnsmasq reload, thus dhcp won't become active
on this interface.
Signed-off-by: David Bauer <mail@david-bauer.net>
The layerscape kernel patches appears to be just some uncleaned local
development tree, where patches are sometimes directly followed by
their revert. While this does not seem a problem in the first place,
it becomes incredibly unpleasant when the upstream kernel changes in
the relevant areas and requires rebase.
This removes all these patch-revert pairs and refreshs the rest.
It removes about 44000 lines of entirely useless code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In order to support SAE/WPA3-Personal in default images. Replace almost
all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for
consistency. Keep out ar71xx from the list as it won't be in the next
release and would only make backports harder.
Build-tested (build-bot settings):
ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway,
sunxi: a53
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Patch 1 introduces a change, and patch 2 reverts it again. Remove
both patches and achieve the same outcome.
Refreshed patches for the target as well.
Cc: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
"type" is already used as a common option for all protocols types, so
using the same option name for the map type makes the configuration
ambiguous. Luci in particular adds controls for both options and sees
errors when reading the resulting configuration.
Use "maptype" instead, but still fallback to "type" if "maptype" is not
set. This allows configurations to migrate without breaking old
configurations.
This addresses FS#3287.
Signed-off-by: Remi NGUYEN VAN <remi.nguyenvan+openwrt@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
TP-LINK published a firmware update for the archer c6 v2.
This updates also reached the factory devices. Newer software version
rejects downgrading to 1.2.x. Use 1.9.x to allow installing the factory images
and have a little bit time to change it again.
Tested on archer c6 v2 with firmware 1.3.1
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
This PR is a blend of several kernel bumps authored by ldir taken from his
staging tree w/ some further adjustments made by me and update_kernel.sh
Summary:
Deleted upstreamed patches:
generic:
742-v5.5-net-sfp-add-support-for-module-quirks.patch
743-v5.5-net-sfp-add-some-quirks-for-GPON-modules.patch
bcm63xx:
022-v5.8-mtd-rawnand-brcmnand-correctly-verify-erased-pages.patch
024-v5.8-mtd-rawnand-brcmnand-fix-CS0-layout.patch
mediatek:
0402-net-ethernet-mtk_eth_soc-Always-call-mtk_gmac0_rgmii.patch
Deleted patches applied differently upstream:
generic:
641-sch_cake-fix-IP-protocol-handling-in-the-presence-of.patch
Manually merged patches:
generic:
395-v5.8-net-sch_cake-Take-advantage-of-skb-hash-where-appropriate.patch
bcm27xx:
950-0132-lan78xx-Debounce-link-events-to-minimize-poll-storm.patch
layerscape:
701-net-0231-enetc-Use-DT-protocol-information-to-set-up-the-port.patch
Build system: x86_64
Build-tested: ath79/generic, bcm27xx/bcm2708, bcm27xx/bcm2711,
imx6, mvebu/cortexa9, sunxi/a53
Run-tested: Netgear R7800 (ipq806x)
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Tested-By: Lucian Cristian <Lucian.cristian@gmail.com> [mvebu]
Tested-By: Curtis Deptuck <curtdept@me.com> [x86/64]
[do not remove 395-v5.8-net-sch_cake-Take-advantage-... patch,
adjust and refresh patches, adjust commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-By: John Audia <graysky@archlinux.us> [ipq806x]
On Mikrotik SPI NOR devices, the firmware partition must be erased when
flashing from stock firmware, otherwise leftover bits (in particular a
kernel signature) can trigger a boot loop.
When booted from initramfs (the only way to install OpenWRT on these
devices), this patch unconditionally erases the firmware partition in
the do_upgrade() stage for all supported SPI NOR devices.
This is forward-ported from ed49d0876 and 20452a8db
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This reverts commit b1f6a5d9df.
In this particular case, the echo command was _not_ useless, but
converted the newlines back to spaces.
Add a comment into the code to make that obvious for the next one
looking at it like me.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The is no reason to catch the output by $() and then echo it again.
Remove the useless echos.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The output is already produced in the inner $() brackets, no need
to catch and echo it again.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The node needs to be terminated by a semicolon.
Fixes: 8484a764df ("ath79: ar724x: make sure builtin-switch is
enabled in DT")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Both TL-WPA8630(P) v1 and v2 feature a button labelled "WiFi".
While this is implemented as KEY_RFKILL for v1 in ar71xx and ath79,
the v2 sets it up as WPS button.
According to the manual, the behavior in OEM firmware is:
"Press and hold the button for 1 second to copy wireless settings
from the main router to the extender. Go to Wi-Fi Clone for more
information. Press and hold the button for at least 5 seconds to
turn the wireless function on or off."
Consequently, and since this is historic behavior on v1 in OpenWrt,
we set this button to KEY_RFKILL on both revisions.
Fixes: ab74def0db ("ath79: add support for TP-Link TL-WPA8630P v2")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The moves a few additional common nodes to the common DTSI files
for qcom-ipq8064-v2.0 and qcom-ipq8065 devices.
Remove a few redundant definitions on the way.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
On ar7240/ar7241 the mdioX node with the builtin-switch is enabled
in the DTSI files, but the parent ethX node is left disabled. It
only gets enabled per device or device family, and has not been
enabled at all yet for the TP-Link WA devices with ar7240, making
the switch unavailable there.
This patch makes sure ð0/ð1 nodes are enabled together with
the &mdio0/&mdio1 nodes containing the builtin-switch.
For ar7240_tplink_tl-wa.dtsi, ð0 is properly hidden again via
compatible = "syscon", "simple-mfd";
This partially fixes FS#2887, however it seems dmesg still does
not show cable (dis)connect in dmesg for ar7240 TP-Link WA
devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The leds block was copied over from the RT-AC85P DTS to the common
DTSI while keeping the device-specific model name in the label.
This moves the LEDs back to the DTS files and adjusts the names to
properly resemble the model name of the devices used at, just like
it is handled on most other devices.
Fixes: 7c5f712e4f ("ramips: add support for Asus RT-AC65P")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This files have been emptied during subtarget consolidation, but
not removed. Remove them now.
Fixes: aff084adf3 ("at91: Merge SAMA5 subtargets")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Itus Networks Shield - 1Ghz dual-core mips64 / Cavium Octeon 3 SoC,
1Gb RAM, 4Gb eMMC,3 GbE 10/100/1000 ports
Information regarding device can be found:
https://deviwiki.com/wiki/Itus_Networks_Shield_Pro
Installing OpenWrt on Itus Networks Shield:
1) Boot Shield
2) On device: mount /dev/mmcblk1p1 /mnt
3) scp openwrt-octeon-itus,shield-router-initramfs-kernel.bin to
/mnt/ItusrouterImage
3a) Optionally: scp openwrt-octeon-itus,shield-router-initramfs-kernel.bin
to /mnt/ItusgatewayImage to allow you to have an emergency recovery
boot in the GATEWAY slot - this slot will have no permament storage and
is used for emergency recovery only when booted in the (G)ateway
position
4) On device: umount /mnt
5) reboot
Once booted, run the sysupgrade via cli or luCi on the
openwrt-octeon-itus,shield-router-squashfs-sysupgrade.tar file the mode
you are running.
Once rebooted, the system installation is complete. Your storage partition
for the mode is inialized and set.
Signed-off-by: Donald Hoskins <grommish@gmail.com>
[cut out sysupgrade-* changes, move a few lines,
drop case CVMX_BOARD_TYPE_ITUS_SHIELD]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, the sysupgrade-* folder used during upgrade in octeon was
hardcoded to contain the board name. Therefore, changing board name
or BOARD_NAME variable in image/Makefile might have broken upgrade.
Improve this by adding a step to determine the folder name via
a wildcard, as it is done for generic nand_upgrade_tar() in
lib/upgrade/nand.sh.
While this still does not remove the problem for existing devices
(which still have the old script), it will entirely remove the
issue on newly added devices on this platform.
Signed-off-by: Donald Hoskins <grommish@gmail.com>
[split into separate patch, add commit message, add return values]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This renames board patches to make finding devices easier
and reorders them based on their board.
The devices are grouped based on the board/cpu_id. New device
patches should be numbered based on their group.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The legacy map version based on the IPv6 Interface Identifier in
draft-ietf-softwire-map-03 was typically used by uncommenting the LEGACY
variable in the map.sh file, which is not ideal. A proper configuration
option is needed instead.
The IPv6 Interface Identifier format described in the draft was
eventually changed in RFC7597, but is still used by some major ISPs,
including in Japan.
Signed-off-by: Remi NGUYEN VAN <remi.nguyenvan+openwrt@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
If not needed, disabling scp allows for a nice size reduction.
Dropbear executable size comparison:
153621 bytes (baseline)
133077 bytes (without scp)
In other words, we trim a total of 20544 bytes.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
ALLNET ALL-WAP02860AC is a dual-band wireless access point.
Specification
SoC: Qualcomm Atheros QCA9558
RAM: 128 MB DDR2
Flash: 16 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9880 Mini PCIe card
Ethernet: 1x 10/100/1000 Mbps AR8035-A, PoE capable (802.3at)
LEDS: 5x, which four are GPIO controlled
Buttons: 1x GPIO controlled
UART: 4 pin header near Mini PCIe card, starting count from white
triangle on PCB
1. VCC 3.3V, 2. GND, 3. TX, 4. RX
baud: 115200, parity: none, flow control: none
MAC addresses
Calibration data does not contain valid MAC addresses.
The calculated MAC addresses are chosen in accordance with OEM firmware.
Because of:
a) constrained environment (SNMP) when connecting through Telnet
or SSH,
b) hard-coded kernel and rootfs sizes,
c) checksum verification of kerenel and rootfs images in bootloder,
creating factory image accepted by OEM web interface is difficult,
therefore, to install OpenWrt on this device UART connection is needed.
The teardown is simple, unscrew four screws to disassemble the casing,
plus two screws to separate mainboard from the casing.
Before flashing, be sure to have a copy of factory firmware, in case You
wish to revert to original firmware.
Installation
1. Prepare TFTP server with OpenWrt initramfs-kernel image.
2. Connect to LAN port.
3. Connect to UART port.
4. Power on the device and when prompted to stop autoboot, hit any key.
5. Alter U-Boot environment with following commands:
setenv failsafe_boot bootm 0x9f0a0000
saveenv
6. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use
'setenv' to do that, then run following commands:
tftpboot 0x81000000 <openwrt_initramfs-kernel_image_name>
bootm 0x81000000
7. Wait about 1 minute for OpenWrt to boot.
8. Transfer OpenWrt sysupgrade image to /tmp directory and flash it
with:
sysupgrade -n /tmp/<openwrt_sysupgrade_image_name>
9. After flashing, the access point will reboot to OpenWrt. Wait few
minutes, until the Power LED stops blinking, then it's ready for
configuration.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[add MAC address comment to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The malta subtargets for mips64 and mips64el fail to start the init process
at boot, resulting in a boot loop. The issue was raised and analyzed within
FS#3277. Investigation suggested code near the [vdso] memory area of the
process was long jumping into a region inaccessible to the process, e.g.
init: - preinit -
init: Launched preinit instance, pid=522
do_page_fault(): sending SIGSEGV to init for invalid read access from 0000000000000360
epc = 0000000000000360 in init[aaab42b000+4000]
ra = 000000fffee385e0 in
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Rebooting in 1 seconds..
Note the low-memory read access and epc are the same. Upstream kernel 5.6
included a relevant patch and discussion:
* d3f703c4359f ("mips: vdso: fix 'jalr t9' crash in vdso code")
Disassembly of the failing kernel's vdso.so confirmed presence of the
telltale long jumps, e.g.:
00000000000007c0 <__vdso_clock_getres@@LINUX_2.6>:
[...]
7dc: 0320f809 jalr t9
[...]
Restore booting mips64/mips64el malta by backporting the above commit:
* 310-v5.6-mips-vdso-fix-jalr-t9-crash-in-vdso-code.patch
Fixes: 54310a3aa0 ("malta: add kernel 5.4 config")
Fixes: FS#3277
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3277
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The most recent patch added add lines in one block instead of in the
appropriate places to keep Makefiles in consistent style. Fix that.
Fixes: ff02e1561f ("pcre: add host variant of libpcre")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This ports the TP-Link TL-WPA8630 v1 from ar71xx to ath79.
Specifications:
SoC: QCA9563
CPU: 750 MHz
Flash/RAM: 8 / 128 MiB
Ethernet: 3x 1G ports (QCA8337 switch)
WLAN: 2.4 GHz b/g/n, 5 GHz a/n/ac (ath10k)
Buttons, LEDs and network setup appear to be almost identical
to the v2 revision.
Powerline interface is connected to switch port 5 (Label LAN4).
Installation:
No "fresh" device was available for testing the factory image.
It is not known whether flashing via OEM firmware GUI is possible
or not. A discussion from 2018 [1] about that indicates a few
adjustments are necessary, but it is not clear whether those
are already implemented with the TPLINK_HEADER_VERSION = 2 or not.
Note that for the TL-WPA8630P v1, the TPLINK_HWID needs to be
changed to 0x86310001 to allow factory flashing.
[1] https://forum.openwrt.org/t/solved-tl-wpa8630p-lede-does-not-install/8161/27
Recovery:
Recovery is only possible via serial.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
34aed01ca865 mt76: mt7915: use ieee80211_free_txskb to free tx skbs
efc8669db5f9 mt76: mt7915: fix max_mpdu_size field for A-MSDU
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Dependencies are meant to express actual run-time dependencies and
strictly speaking, libselinux can be build and used on kernels without
SELinux (not in a very meaningful way, but never mind).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The commands to read ath9k caldata on mikrotik subtarget are
mostly repetitive, so let's put them into a function to make
writing and reading them easier.
This function will only be required when patching the MAC address.
For cases where it is put correctly into the calibration data by
the vendor, caldata_sysfsload_from_file can be used directly as
done for ath10k at the moment.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the MikroTik RouterBOARD 760iGS router.
It is similar to the already supported RouterBOARD 750Gr3.
The 760iGS device features an added SFP cage, and passive
PoE out on port 5 compared to the RB750Gr3.
https://mikrotik.com/product/hex_s
Specifications:
- SoC: MediaTek MT7621A
- CPU: 880MHz
- Flash: 16 MB
- RAM: 256 MB
- Ethernet: 5x 10/100/1000 Mbps
- SFP cage
- USB port
- microSD slot
Unsupported:
- Beeper (requires PWM driver)
- ZT2046Q (ADS7846 compatible) on SPI as slave 1 (CS1)
The linux driver requires an interrupt, and pendown GPIO
These are unknown, and not needed with the touchscreen
only used for temperature and voltage monitoring.
ads7846 hwmon:
temp0 is degrees Celsius
temp1 is voltage * 32
GPIOs:
- 07: input passive PoE out (lan5) compatible (Mikrotik) device connected
- 17: output passive PoE out (lan5) switch
Installation through RouterBoot follows the usual MikroTik method
https://openwrt.org/toh/mikrotik/common
To boot to intramfs image in RAM:
1. Setup TFTP server to serve intramfs image.
2. Plug Ethernet cable into WAN port.
3. Unplug power, hold reset button and plug power in.
Wait (~25 seconds) for beep and then release reset button.
The SFP LED will be lit in RouterBoot, but will not be lit in OpenWRT.
4. Wait for a minute. Router should be running OpenWrt,
check by plugging in to port 2-5 and going to 192.168.1.1.
To install OpenWrt to flash:
1. Follow steps above to boot intramfs image in RAM.
2. Flash the sysupgrade.bin image with web interface or sysupgrade.
3. Once the router reboots you will be running OpenWrt from flash.
OEM firmware differences:
- RouterOS assigns a different MAC address for each port
- The first address (E01 on the sticker) is used for wan (ether1 in OEM).
- The next address is used for lan2.
- The last address (E06 on the sticker) is used for sfp.
[Initial port work, shared dtsi]
Signed-off-by: Vince Grassia <vincenzo.grassia@zionark.com>
[SFP support and GPIO identification]
Signed-off-by: Luka Logar <luka.logar@iname.com>
[Misc. fixes and submission]
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
[rebase, drop uart3 from state_default on 750gr3, minor commit
title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves some common definitions for Mikrotik devices, mainly
routerboot partitions and reset key, to a common DTSI file.
While at it, remove unused hard_config DT label.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
