WPJ419 is still manually defining SPI node, so lets
convert it to use the existing upstream labels for SPI node.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
WPJ419 is still manually defining pinctrl node, so lets
convert it to use the existing upstream labels for pinctrl node.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
WPJ419 is still manually defining PCIe node, so lets
convert it to use the existing upstream labels for PCIe node and while we
are here use the -gpios suffix instead.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some boards are still defining MDIO nodes under soc instead of using the
existing upstream labels to reference them so convert them.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some boards are still defininig I2C nodes under soc instead of using the
existing upstream labels to reference them so convert them.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some boards are still defininig UART nodes under soc instead of using the
existing upstream labels to reference them so convert them.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
This device does not have NAND enabled at all and NAND is the only consumer
of QPIC BAM DMA, so drop the node.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
WPJ419 is still manually defining dma nodes(And even some labels), so lets
convert it to use the existing upstream labels for DMA nodes.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, a lot of boards are still not using the existing label to
reference the crypto node, so lets rectify this.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, a lot of boards are still not using the existing label to
reference the prng node, so lets rectify this.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, a lot of boards are still not using the existing label to
reference the watchdog node, so lets rectify this.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that DSA is enabled and the MAC addresses are set properly, we can
use it.
Signed-off-by: Corey Minyard <minyard@acm.org>
Link: https://github.com/openwrt/openwrt/pull/15358
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The code that was there was just taking whatever was left in the
registers, which was just wrong. Set the addresses using the value from
the u-boot environment, the same way the OEM firmware does.
Signed-off-by: Corey Minyard <minyard@acm.org>
Link: https://github.com/openwrt/openwrt/pull/15358
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This commit converts the EAP1300 to DSA setup.
Signed-off-by: Corey Minyard <minyard@acm.org>
Link: https://github.com/openwrt/openwrt/pull/15358
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
It's needed to get the MAC addresses for the Engenius EAP1300.
Signed-off-by: Corey Minyard <minyard@acm.org>
Link: https://github.com/openwrt/openwrt/pull/15358
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Commit 6136ebabc5 ("ipq40xx: 6.6: fix DTS to use reference for usb
node") fixed only some of the reference to USB node but many others were
still using the old broken usb3/usb2. Fix every reference to those node
and move them on using the tag name.
Fixes: 6136ebabc5 ("ipq40xx: 6.6: fix DTS to use reference for usb node")
Link: https://github.com/openwrt/openwrt/pull/15392
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
No changes other than the merging itself are intended in this commit.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15345
Signed-off-by: Robert Marko <robimarko@gmail.com>
Apply stylistic changes to facilitate DTS merging with WHW03 V1.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15345
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hardware:
=========
SOC: Qualcomm IPQ4019
WiFi 1: QCA4019 IEEE 802.11b/g/n
WiFi 2: QCA4019 IEEE 802.11a/n/ac
WiFi 3: QCA9886 IEEE 802.11a/n/ac
Bluetooth: Qualcomm CSR8510 (A10)
Zigbee: Silicon Labs EM3581 NCP + Skyworks SE2432L
Ethernet: Qualcomm Atheros QCA8072 (2-port)
Flash: Samsung KLM4G1FEPD (4GB eMMC)
RAM (NAND): 512MB
LED Controller: NXP PCA9633 (I2C)
Buttons: Single reset button (GPIO).
Ethernet:
=========
The device has 2 ethernet ports, configured as follows by default:
- left port: WAN
- right port: LAN
Wifi:
=====
The Wifi radios are turned off by default. To configure the router,
you will need to connect your computer to the LAN port of the device.
Bluetooth and Zigbee:
=====================
Configuration included but not tested.
Storage:
========
For compatibility with stock firmware, all of OpenWrt runs in a 136 MiB
eMMC partition (of which there are two copies, see below). You can also
use partition /dev/mmcblk0p19 "syscfg" (3.4 GiB) any way you see fit.
During very limited tests, stock firmware did not mount this partition.
However, backing up its stock content before use is recommended anyway.
Firmware:
=========
The device uses a dual firmware mechanism: it automatically reverts to
the previous firmware after 3 failed boot attempts.
You can switch to the inactive firmware copy by changing the "boot_part"
U-Boot environment variable. You can also do it by turning on the device
for a couple of seconds and then back off, 3 times in a row.
Installation:
=============
OpenWrt's "factory" image can be installed via the stock web UI:
1. Login to the UI. (The default password is printed on the label.)
2. Enter support mode by clicking on the "CA" link at the bottom.
3. Click "Connectivity", "Choose file", "Start", and ignore warnings.
This port is based on work done by flipy (https://github.com/flipy).
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15345
Signed-off-by: Robert Marko <robimarko@gmail.com>
AVM FRITZ!Repeater 1200 does not use QCA807x PHY at all and thus it
disables all of the individual PHY nodes, however this is not enough
anymore since the conversion to PHY package.
Now its now enough to disable the PHY-s in the package alone, but the PHY
package node itself must also be disabled.
Fixes: 1b931c33a2 ("ipq40xx: adapt to new Upstream QCA807x PHY driver")
Fixes: #15355
Link: https://github.com/openwrt/openwrt/pull/15365
Signed-off-by: Robert Marko <robimarko@gmail.com>
Turn on SoC pull-ups on I2C pins, since there are no discrete pull-up
resistors on the bus.
Increase clock to 400 kHz. Both chips on the bus support 400 kHz. I
tested the ISL28022 at 4,000 reads/sec and didn't see any garbled output
or bus hangs, even with SoC drive strength reduced to 2 for the test.
Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15334
Signed-off-by: Robert Marko <robimarko@gmail.com>
Enable USB 3.0 controller, disable USB 2.0 controller.
The USB 2.0 port on the AP-303H is actually connected to the USB 3.0
controller's HS phy. Enable the HS phy only, since the SS lanes are not
brought out to the connector.
Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
Use NVMEM to assign "factory sticker" MAC address to WAN ethernet
interface. Set LAN address to sticker + 1.
Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
Set DEVICE_DTS_DIR to /qcom by default instead of limiting it to
TESTING_KERNEL since we moved 6.6 to default version.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This device supports channel ranges 36-64 and 100-165, just like
others based on the same reference design, but its current DTS is
unnecessarily restricting these ranges to 36-48 and 149-165.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Change the RGB indicator LED color for the running state from green to
blue. There are various reasons for this change:
- In stock firmware, green means internet connection is up, red means it
is down, and blue means indeterminate. To track stock behavior as
closely as possible, OpenWrt should indicate blue by default.
- In the current 23.x OpenWrt releases for this router, the led glows
blue all the time -not green- because the bootloader sets it blue
and there is an OpenWrt bug that makes it unable to control the LED.
The bug is fixed in master, so without this commit there would be an
unexpected change of behavior for this device in the next release.
- The ports other closely related Linksys devices (such as EA8300 and
MR8300) get this right and use blue for the running state.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
The RGB LED should glow green in the 'running' state, but it
was glowing cyan because the blue component defaulted to 'on'.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Add pending patch fixing mtdcore with MTD OTP with a fragile detection
if Nand supports OTP. Patch has been sent upstream and will be backported
to stable kernel if accepted.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Rework kernel patches for new kernel. Mainly adaptation for patch
related to DTS, OOB Tagger and SDHCI patch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix DTS to use reference for usb node instead of redefining
them since upstream usb node names changed from usb2/3 to usb.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Since with recent kernel version DTS moved to a dedicated directory,
it's required to split files to per kernel version to follow kernel
version directory structure.
Also makes use of DEVICE_DTS_DIR to target the correct DTS directory
based on the kernel version.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Without UBINIZE_OPTS it is possile to have error:
"ubi0 error: ubi_attach_mtd_dev: failed to atach mtd23, error -22"
This solve this problem.
Signed-off-by: Marcin Gajda <mgajda@o2.pl>
