Commit Graph

235 Commits

Author SHA1 Message Date
Mathias Kresin
e20965811d ar71xx: fix ath9k default LED changes fallout
Since 192f0a3db8 ("ath9k: unset the default LED pin if used by
platform leds") the default ath9k wireless LED is not set as soon as
any pin of the ath ath9k gpio controller is used.

All touched boards have leds defined which are using the gpio pins
exposed by the ath9k driver but rely on a default set wireless led
trigger.

Add the wireless leds were missing and setup the wireless phy trigger
in userspace.

Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-13 08:18:57 +02:00
Mathias Kresin
1f5ea4eae4 ar71xx: add correct named default wireless led by using platform leds
Instead of renaming the default wireless led attached to the wireless
chip, add a new led using the platform leds with the phy0tpt trigger
set in userspace.

When switching ar71xx to device tree, the same can be done by using the
build in GPIO controller and without adding new bindings.

Drop the now unused platform code.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-08 14:30:00 +02:00
Ron Angeles
156d9255f2 ar71xx: add userspace support for Mikrotik RB2011iL
Kernel/hardware support for this board has been implemented since
Chaos Calmer. This set of patches is to get the board identified in
userland. This will allow support for things like sysupgrade,
configuring initial LED state, configuring initial switch state, etc.

Signed-off-by: Ron Angeles <ronangeles@gmail.com>
2017-04-03 12:29:07 +02:00
Christian Mehlis
dc4eae7a8c ar71xx: Compex WPJ563 support
Specification:
- SoC: Qualcomm Atheros QCA9563 (775 MHz, MIPS 74Kc)
- RAM: 128 MiB
- Storage: 16MB NOR flash
- Wireless: Built into QCA9563 (Dragonfly), PHY modes b/g/n, 3x3 MIMO
- Ethernet: 2x1G

Tested and working:
- ethernet / switch / lan / wan
- 2.4GHz SoC wifi
- PCIe
- leds
- buzzer

Ramload:
- tftpboot 0x84000000 lede-ar71xx-generic-wpj563-16M-initramfs-uImage.bin
- bootm 0x84000000

Install:
- tftpboot 0x80500000 lede-ar71xx-generic-wpj563-16M-squashfs-sysupgrade.bin
- erase 0x9f030000 +$filesize
- erase 0x9f680000 +1
- cp.b $fileaddr 0x9f030000 $filesize

Erasing 0x9f680000 is required because uboot defines
"bootcmd=bootm 0x9f680000 || bootm 0x9f030000", so it first tries to boot
the higher address. I think the 16 mb flash are intended to be used as
8+8mb for a fallback image. In my hardware only the lower address has a
bootable image. But to make sure future hardware will boot lede too, I
erase one block, so uboot will skip this address.

Signed-off-by: Christian Mehlis <christian@m3hlis.de>
2017-03-30 09:57:22 +02:00
Piotr Dymacz
4436979c83 ar71xx: add support for P&W R602N and CPE505N
P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also
labeled as R602F, R602, etc.) is a simple N300 router with 5-port
10/100 Mbps switch, non-detachable antennas and USB.

CPE505 is an outdoor CPE with PoE support and detachable antennas.

Both devices are based on Qualcomm/Atheros QCA9531 v2.

Common specification:

- 650/597/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- UART (J2) header on PCB

R602N specification:

- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm
- 2x external, non-detachable antennas
- 7x LED, 1x button

CPE505N specification:

- 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V)
- 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm
- 2x external, detachable antennas (RP-SMA connectors)
- 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button

Flash instructions:

It seems that there are many different versions of the firmware which
these devices are shipped with. The generic/standard one is based on
some modified OpenWrt and LEDE firmware can be flashed directly from
vendor's webgui or with sysupgrade (root password is "admin123").

Before flashing, make sure (use "fw_printenv") that the kernel load
address in your device is set to "0x9f050000" (bootcmd variable is
"bootm 0x9f050000"). If your device uses different load address, you
should first change it, under vendor's firmware, with command:

fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS"

Where OLD_ADDRESS is previous kernel load address (in CPE505 version
I got access to, it was "0x9fe80000"). This will allow you to use
both the vendor's and LEDE firmware.

If version of your device contains empty U-Boot environment (you will
get information about this after issuing "fw_printenv"), you should
use U-Boot, serial line access and TFTP to perform firmware upgrade:

1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS"
5. saveenv && reset

These devices contain also web recovery mode inside U-Boot. It can be
started with pressing the reset button for around 3 seconds just after
the device powerup. Web recovery panel is available on "192.168.10.9"
and to be able to use it, IP on your PC must be set to "192.168.10.10".

Make sure to change kernel load address before using recovery mode or
the U-Boot will not be able to load LEDE firmware.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-23 17:59:47 +01:00
Vaclav Svoboda
0d9adb4832 ar71xx: add support for TP-LINK TL-WR840N v2 and v3
This patch adds support for the TP-LINK TL-WR840N v2 and v3.

- SoC: Qualcomm QCA9533-BL3A (650 MHz)
- RAM: 32 MiB (Zentel A3S56D40GTP)
- Flash: 4 MiB
   (v2: Macronix MX 25L323F)
   (v3: Winbond 25Q32FVSIG)
- LAN: 4x 100M
- WAN: 1x 100M

Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
2017-03-23 09:41:15 +01:00
Ryan Mounce
978998628f ar71xx: add support for MikroTik hAP ac
This patch adds initial support for the MikroTik RouterBOARD hAP ac
(RB962UiGS-5HacT2HnT).

All functions are supported except:
-SFP cage (eth1) is not working
-WLAN LEDs are not working

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2017-03-23 09:35:14 +01:00
Ryan Mounce
540edf7045 ar71xx: add support for MikroTik hAP ac lite
This patch adds support for the MikroTik RouterBOARD hAP ac lite
(RB952Ui-5ac2nD).

The hAP ac lite is nearly identical to the hAP, with an added QCA9887
5GHz radio. The 2.4GHz radio ID is also changed in the hAP ac lite.

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2017-03-23 09:35:14 +01:00
Thibaut VARENE
e3dc036cbf ar71xx: add support for RB LHG 5nD
This patch adds support for the MikroTik RouterBOARD LHG 5
https://routerboard.com/RBLHG-5nD

Specifications:
- SoC: Atheros AR9344 (600MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin AR9344 5GHz, 2x2:2
- Ethernet: 1x100M

Initial flash via initramfs, like all other RB devices.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-03-15 23:00:52 +01:00
Daniel Gonzalez Cabanelas
080c6fa476 ar71xx: WNDR4300: Fix network vlan IDs
The Netgear WNDR4300 has the VLAN IDs flipped in LuCi, fix it.

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
2017-03-13 00:13:18 +01:00
Shuanglin Liu
53ef20f65a ar71xx: add support for Rockeetech AP531B0
Specification:
- SoC: Qualcomm Atheros QCA9531 (650/400/216 MHz (CPU/DDR/AHB))
- RAM: 64 MiB DDR2
- Storage: 16 MiB of flash (optional 16 MiB second flash)
- Wireless: built into QCA9531 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0) 1x100M (port 4)
- PCI-E: x1
- SIMcard slot: x1
- USB 2.0 port: x1 (optional)
- Ext GPIO pin: x8
- UART for serial console: x1
- External watchdog: x1 (optional)
- Power supply: 9-48V (DC jack/passive PoE)

Installation through tftp:
- Copy <Firmware Image Name> into tftp directory
- Connect board via ttl port and Ethernet port
- Boot the AP531B0
- When "Autobooting in 1 seconds" appears press Enter
- Set serverip and ipaddr appropriate
  (e.g. setenv serverip 192.168.88.10;setenv ipaddr 192.168.88.1)
- Enter "tftp 0x8050000 <Firmware Image Name>"
- Enter "erase 0x9f050000 +$filesize"
- Enter "cp.b 0x80500000 0x9f050000 $filesize"
- Enter "reset"

Signed-off-by: Shuanglin Liu <roboidler@gmail.com>
2017-03-12 17:38:31 +01:00
Wojciech Jowsa
f223c4a923 ar71xx: set status led for the gl-* boards
Signed-off-by: Wojciech Jowsa <w.jowsa@radytek.com>
2017-03-06 07:50:11 +01:00
Weijie Gao
3ee793f601 ar71xx: fix vlan settings for some boards
For AR71XX devices, GMAC1 always connects port 0 of the built-in switch,
as the CPU port.

This patch sets correct vlan for some devices with wrong settings:
a) mark port 0 as CPU port, tagged
b) reverse port order, marking these ports untagged

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2017-02-20 09:27:43 +01:00
Thomas Roberts
f9278337cf ar71xx: add support for TL-WR802N Version 2
This patch adds support for the TP-Link TL-WR802N Version 2.

Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of FLash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)

Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to http://192.168.0.1 (default user is "admin" & password is "admin)
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware "*.factory-us.bin" or  "*.factory-eu.bin" for eu model
- Click upgrade

Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
      Serial Configuration 115200 8n1

- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
    (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
    (e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
    (e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
    (e.g bootm 0x9f020000)

Signed-off-by: Thomas Roberts <tom.p.roberts@gmail.com>
2017-02-20 09:10:17 +01:00
Henryk Heisig
d6baeb5c48 ar71xx: fix lan ports on archer C59 and C60
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-02-17 10:30:48 +01:00
Thibaut VARENE
b2044a7f60 ar71xx: add support for RB750r2
This patch adds support for the MikroTik RouterBOARD hEX lite
https://routerboard.com/RB750r2

Specifications:
- SoC: Qualcomm QCA9531 (850MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in)

This ethernet router is based on the same platform as the hEX PoE lite (it
shares the same board identifier), but has no USB and no PoE out.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:58 +01:00
Thibaut VARENE
19f42663d2 ar71xx: add support for RB750UPr2
This patch adds support for the MikroTik RouterBOARD hEX PoE lite
https://routerboard.com/RB750UPr2

Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in, 1 PoE out)
- USB: Type A

This ethernet router is based on the same platform as the wireless router hAP.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:58 +01:00
Thibaut VARENE
8cbb2ac633 ar71xx: add support for RB951Ui-2nD
This patch adds support for the MikroTik RouterBOARD hAP
https://routerboard.com/RB951Ui-2nD

Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin QCA9531, 2x2:2
- Ethernet: 5x100M (1 PoE in, 1 PoE out)
- USB: Type A

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:58 +01:00
Thibaut VARENE
b18bae37a4 ar71xx: provide support for RB-941-2nD via mach-rbspi.c
This patch implements support for the hAP lite in mach-rbspi.c

hAP lite was supported via mach-rb941.c, so this file is removed
as well as the corresponding build bits.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:57 +01:00
Thibaut VARENE
c59fa94eee ar71xx: add support for RB mAP L-2nD
This patch adds support for the MikroTik RouterBOARD mAP lite
https://routerboard.com/RBmAPL-2nD

Specifications:
- SoC: Qualcomm QCA9533 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin QCA9533, 2x2:2
- Ethernet: 1x100M

This is another 16M SPI NOR mikrotik device. The machine file is named
mach-rbspi.c because I plan to add support for several of the other spi-based
RouterBOARD devices in subsequent patches: they share most of the hardware
and thus the same codebase.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:57 +01:00
Alexandru Gagniuc
6cce9557a0 ar71xx: Add support for D-Link EBR-2310 Rev. C
Add support for the EBR-2310, which is almost identical to the DIR-615
rev E4, without the wifi.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2017-02-14 12:27:14 +01:00
Piotr Dymacz
56561b9f51 ar71xx: add support for TP-Link TL-WA850RE v2
TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.

Short specification:

- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB

Flash instruction: use "factory" image directly in vendor GUI.

Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.

You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin

Image was tested only in US version of the device, but should work
also with the same device version sold in other countries.

Available FLASH space, with LEDE trunk, is only 240 KB.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-14 12:25:33 +01:00
Sven Eckelmann
640f9158e2 ar71xx: add user-space support for the OpenMesh A40
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
174605c467 ar71xx: add user-space support for the OpenMesh A60
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
bdfe4c1218 ar71xx: add user-space support for the OpenMesh OM2Pv4/-HSv4
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:04 +01:00
Jo-Philipp Wich
ea269c37b8 ar71xx/ipq806x/mediatek/mvebu: fix network defaults
After "73d923e base-files: emit tagged switch configuration by default"
some default network configurations are broken because the lan and wan
ifnames are forcibly set to untagged netdevs.

Adjust the offending set_interfaces_lan_wan() calls to use the proper
tagged device names.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-02-07 09:32:28 +01:00
Henryk Heisig
e39dc8d823 ar71xx: add support to TP-Link Archer C59v1 and C60v1
TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- 8x LED (controled by 74HC595), 3x button
- UART header on PCB

TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Currently not working:
- Port LAN1 on C59, LAN4 on C60
- WiFi 5GHz (missing ath10k firmware for QCA9886 chip)
- Update from oficial web interface ( tplink-saveloader not support "product-info")

Flash instruction:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. reset

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-01-26 11:38:21 +01:00
Qian Zheng
b822f29f25 ar71xx: fix netgear wndr3700 v1/v2, wndr3800/wndr3800ch switch port mapping
Signed-off-by: Qian Zheng <sotux82@gmail.com>
2017-01-26 11:38:20 +01:00
Qian Zheng
3d4069fb8e ar71xx: fix netgear wnr2000 v3 switch port mapping
Signed-off-by: Qian Zheng <sotux82@gmail.com>
[Jo-Philipp Wich: fix alphabetical order after merging with gl-ar300 case]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-01-26 11:38:20 +01:00
Qian Zheng
810eb8d0ea ar71xx: fix tl-wr841n-v7 switch port mapping
Signed-off-by: Qian Zheng <sotux82@gmail.com>
[Jo-Philipp Wich: fix alphabetical order]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-01-26 11:38:20 +01:00
YuheiOKAWA
261415a660 ar71xx: add support for PQI Air Pen
SoC: AR9331
Ethernet x1, Wireless 2.4G, uSD card slot x1.
USB Power, include Li-Po Battery.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

Changes in v2:
alphabetical ordering, tabs fron spaces.
2017-01-20 00:52:48 +01:00
Conor O'Gorman
274546046d ar71xx: add Abicom SC1750 support
Support Abicom International Scorpion SC1750 Board

QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB Nand Flash
16MB Nor Flash
1x SFP, 1x PCIe
2x 10/100/1000 Ethernet
135x100 mm
802.11ng/g/b
802.11ac/an/a

Signed-off-by: Conor O'Gorman <i@conorogorman.net>
2017-01-20 00:40:40 +01:00
Conor O'Gorman
d38ffd8cd9 ar71xx: add Abicom SC450 support
Support Abicom International Scorpion SC450 Board

QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB NAND Flash
16MB NOR Flash
10/100/1000 Ethernet
15W Max, 3x3 Mode, Full Power TX Power
802.3-at POE+ & DC Input options
100x 85mm
USB
PCIe
SFP
GPIO/LED

Signed-off-by: Conor O'Gorman <i@conorogorman.net>
2017-01-20 00:40:33 +01:00
Conor O'Gorman
eb97f41fc2 ar71xx: add Abicom SC300M support
Support Abicom International Scorpion SC300M Module

QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB Nand Flash
16MB SPI Flash
802.11a/na/b/g/ng
GPIO x 22, USB x2, PCIe x2
10/100/1000 Ethernet
23dBm, Optional Onboard Antenna
DC Input, 8-20V DC
85 x 55 mm

Signed-off-by: Conor O'Gorman <i@conorogorman.net>
2017-01-20 00:40:27 +01:00
Cezary Jackiewicz
05115e9656 ar71xx: fix network config for Mikrotik RB411U
Mikrotik RB411U has only one ethernet port - eth0. This patch allows to create
correct config with one lan section.

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2017-01-16 20:40:12 +01:00
Thibaut VARENE
3f7841a70a ar71xx: add support for RB-941-2nD
Add full support for Mikrotik RB-941-2nD (hAP lite)

Original patch by Sergey Sergeev <adron@yapic.net> and
more information is available here:
https://wiki.openwrt.org/toh/mikrotik/rb941_2nd
I updated and adapted the patch to apply cleanly to LEDE trunk
and added proper numbering for the switch ports (matching case
labels).
Tested working on actual hardware with the information
provided in the above webpage. Sysupgrade works.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-16 20:40:12 +01:00
Felix Fietkau
d6c77b9d99 ar71xx: default to external USB power on RB-912UAG
There's a GPIO that can switch between power to USB pins for the
internal MiniPCIe slot or the external USB port.
People are more likely to use the external one so enable it by default.
Existing configurations should be unaffected

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-13 10:53:05 +01:00
Matthias Schiffer
1fef80f29c
ar71xx: add support for TP-Link WBS210/510
The devices are mostly identical to the CPE210/510, but use external
antennas.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-01-05 16:01:17 +01:00
Tal Keren
9c475eca3e ar71xx: add support for TP-Link RE450
Add full support for TP-Link RE450.
The wireless SoC is similiar to Archer C7: QCA9558 + QCA9880 (pci).
The ethernet interface is AR8035, but the mdio is connected to the gpio and
the chipset builtin mdio bus isn't used, which is unique (and weird), so the
kernel gpio mdio module is used.
The two ethernet leds are connected to the GPIO, so they are both configured,
one to indicate link status and the other to indicate data transfer.

The generation of the image was added to the image Makefile.
The return value of tplink-safeloader is not ignored anymore (to fail on error)

The result factory image is flashable from the stock web ui.

Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: ar71xx: RE450: do not build RE450 for nand]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
[hyniu@o2.pl: ar71xx: RE450: Renaming LED accordance with the standard]
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[jo@mein.io: squash fixes from Radek and Henryk into original commit]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-12-22 14:50:05 +01:00
Ludwig Thomeczek
1a4d07c2c5
ar71xx: add support for TP-LINK WR1043ND v4
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
2016-12-20 14:38:48 +01:00
David Lutz
aada15af93
ar71xx: add support for TP-LINK TL-WR940N v4
Signed-off-by: David Lutz <kpanic@hirnduenger.de>
2016-12-16 11:12:46 +01:00
Jo-Philipp Wich
98b14e0906 ar71xx: fix TL-WR842N v2 switch port order
The TL-WR842N v2 has the following switch port layout with swconfig port 0
being connected to eth1:

            Power  LAN4    LAN3    LAN2    LAN1    WAN     USB
             (*) | [...] | [...] | [...] | [...] | [...] | [.]
    swconfig port:   1       4       3       2      n/a
    netdev:        eth1    eth1    eth1    eth1    eth0

Adjust the board defaults to match this model specific layout.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-12-14 18:43:48 +01:00
Felix Fietkau
a5923cd549 ar71xx: remove PB92 reference design board support
Due to flash size limitations, support for this board has not been
functional for years

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Felix Fietkau
30285facbe ar71xx: remove AP113 reference design board support
Due to flash size limitations, support for this board has not been
functional for years

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Felix Fietkau
441ee62931 ar71xx: remove AP83 reference design board support
This board is very old and unlikely to still be relevant today. Support
for it contains a significant amount of device specific baggage which is
worth getting rid of.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Piotr Dymacz
c198ca682c ar71xx: add support for YunCore SR3200 and XD3200
YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9563+QCA9882+QCA8337N.

YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount
AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334.

Common specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB or RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm
- 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm

SR3200 specification:

- 5x 10/100/1000 Mbps Ethernet
- 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips)
- 3x LED (+ 5x LED in RJ45 sockets), 1x button
- UART header on PCB

XD3200 specification:

- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
- 4x internal antennas
- 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button
- UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB

LED for 5 GHz WLAN is currently not supported on both devices as it is
connected directly to the QCA9882 radio chip.

Flash instruction under vendor firmware, using telnet/SSH:

1. If your firmware does not have root password, go to point 5
2. Connect PC with 192.168.1.x address to LAN or WAN port
3. Power up device, enter failsafe mode with button (no LED indicator!)
4. Change root password and reboot (mount_root, passwd ..., reboot -f)
5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP
6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
7. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
- mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware

Flash instruction under U-Boot, using UART:

1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-12-12 09:57:40 +01:00
Matthias Schiffer
9c5af2489a
ar71xx: fix LEDs and sysupgrade support for TL-WA801ND v3
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-12-06 19:08:35 +01:00
João Chaínho
39433bb618 ar71xx: Fix switch config on Mikrotik RB450/G
This patch fixes the ethernet switch initial config for Mikrotik RB450 and RB450G.
The previous version wrongly changed the RouterStation Pro config. This one creates a specific config for the RB450G and leaves the RouterStation Pro unchanged.

Signed-off-by: João Chaínho <joaochainho@gmail.com>
2016-11-21 10:11:37 +01:00
Piotr Dymacz
e33dcd1cfe ar71xx: add support for YunCore CPE830
CPE830 is a clone of AP90Q, with different type of antenna (panel)
and additional 4 LEDs for WiFi signal level indication.

Use the same flash approach as for YunCore AP90Q.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
eb9ba2b91e ar71xx: add support for YunCore CPE870
YunCore CPE870 is an outdoor CPE/AP based on Atheros AR9341.
Short specification:

- 535/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SKY65174-21), up to 30 dBm
- internal 14 dBi panel antenna
- 8x LED, 1x button
- UART (JP1) header on PCB

Flash instruction (do it under U-Boot, using UART):

1. tftp 0x80060000 lede-ar71xx-generic-cpe870-squashfs-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. setenv bootcmd "bootm 0x9f020000"
5. saveenv && reset

Vendor firmware access (login/password): Admin/5up

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
01dda0659e ar71xx: add support for YunCore AP90Q
YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2.
Short specification:

- 650/600/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz with external PA, up to 29 dBm
- 2x internal 5 dBi omni antennas
- 4x LED, 1x button
- UART (JP1) header on PCB

Flash instruction under U-Boot, using UART:

1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Flash instruction under vendor fimrware, using telnet/SSH:

1. Connect PC with 192.168.1.x address to WAN port
2. Power up device, enter failsafe mode with button (no LED indicator!)
3. Change root password and reboot (mount_root, passwd ..., reboot -f)
4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP
5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
6. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9f050000"
- mtd erase firmware
- mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
16afa08d19 ar71xx: add support for COMFAST CF-E380AC v1 and v2
COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE
support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035.

There are two versions of this model, with different RAM
and U-Boot mtd partition sizes:
- v1: 128 MB of RAM, 128 KB U-Boot image size
- v2: 256 MB of RAM, 256 KB U-Boot image size

Version number is available only inside vendor GUI,
hardware and markings are the same.

Short specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 1x 10/100/1000 Mbps Ethernet, with PoE support
- 128 or 256 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm
- 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm
- 6x internal antennas
- 1x RGB LED, 1x button
- UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB
- external watchdog (Pericon Technology PT7A7514)

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
31952dbd1c ar71xx: add support for COMFAST CF-E320N v2 and CF-E520N/CF-E530N
As we already have support for CF-E316N v2 and many devices from
this vendor look similar, the support was included in existing
mach-*.c file, with few cleanups and fixes.

All 3 devices are based on Qualcomm/Atheros QCA9531 v2.

COMFAST CF-E320N v2 is a ceiling mount AP with PoE support.
Short specification:

- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x RGB LED, 1x button
- UART (J1), GPIO (J9) and USB (J2) headers on PCB
- external watchdog (Pericon Technology PT7A7514)

COMFAST CF-E520N/CF-E530N are in-wall APs with USB and PoE support.
They seem to have different only the front panel.
Short specification:

- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, WAN with PoE support
- 1x USB 2.0 (in CF-E520N covered by panel, available on PCB)
- 32 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x LED, 1x button
- UART (J1) headers on PCB

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Jaylin Yu
7ee6ab1a31 ar71xx: Add usable, inactive LEDs on OpenMesh devices
OpenMesh devices have often LEDs which are not yet used by OpenWrt. These
should still be available as disabled LEDs in the system configuration for
easier modification.

Signed-off-by: Jaylin Yu <jaylin.yu@open-mesh.com>
[sven.eckelmann@open-mesh.com: Remove LEDs already specified via diag.sh,
 add wifi/status LEDs]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-11-16 10:54:33 +01:00
FUKAUMI Naoki
0165203304 ar71xx: add support for Buffalo BHR-4GRV2
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
2016-11-16 10:54:33 +01:00
Martin Weinelt
5247ac2f80
ar71xx, ramips: reduce CPU load and flickering on devices using rsslieds
Polling every 40ms causes more than 10% CPU load on weak devices. An
interval of 200ms is much more reasonable.

Signed-off-by: Martin Weinelt <martin@darmstadt.freifunk.net>
[Matthias Schiffer: adapt OpenWrt patch; add ramips; extend commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-11-16 01:42:15 +01:00
Henryk Heisig
1b2b3cb8be ar71xx: wpa8630: change board name to tl-wpa8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-08 11:17:10 +01:00
Henryk Heisig
8cc0c34ef5 ar71xx: Add support to Powerline ac TP-Link WPA8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-31 17:13:37 +01:00
Chris Blake
53b43e65e7 ar71xx: Add net config for MR12 & MR16
Both the MR12 and MR16 are single gigabit ethernet devices, similar to the
MR18. This change gives them the correct network config on a fresh install.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
[Jo-Philipp Wich: adjust for alphabetical ordering, line wrap commit msg]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-10-31 12:52:56 +01:00
Stijn Tintel
e3875350f3 ar71xx: add support for D-Link DAP-2695 rev. A1
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
2016-10-27 01:50:42 +03:00
Julius Schulz-Zander
a71a8955f2 ar71xx: add support for TP-Link WR802N v1
This patch adds support solely for version 1 of the TP-Link WR802N.
It is based on Rick Pannen's patch posted on the OpenWrt devel list.

Signed-off-by: Julius Schulz-Zander <julius@inet.tu-berlin.de>
2016-10-26 12:37:45 +02:00
Jing Lin
7ba9a3a504 ar71xx: Add support to DomyWifi DW33D
Signed-off-by: Jing Lin <mumuqz@163.com>
2016-10-25 17:51:08 +02:00
Henryk Heisig
f5aa459043 ar71xx: Add support to TP-Link EAP120
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-18 09:18:55 +02:00
Christian Lamparter
098f7156cc ar71xx: add support for the Airtight C-60
This patch adds support for the Airtight C-60.

SOC:	Atheros AR9344 rev 2 (CPU:560.000MHz)
RAM:	128 MiB
NOR:	MX25L3205D 4MiB
NAND:	ST Micro NAND 32MiB 3,3V 8-bit
SW-NET:	AR8327N (2 Ports)
WLAN1:	Dual-Band AR9340 Rev:2 (built-in SoC)
WLAN2:	Dual-Band AR9300 Rev:4 PCIe Chip

The switch is setup for an accesspoint:
	LAN1: (gigabit) is the wan-port.
	LAN2: (fast ethernet) is bridged with the br-lan.

Flashing Guide (via initramfs):
  1. Connect a PC to the serial port of the C-60.
     power up the C-60.

     Enter u-boot command prompt:
     #> nand erase
     #> setenv bootcmd "bootm 0x9f060000"
     #> saveenv
     #> setenv ipaddr 192.168.1.1
     #> setenv netmask 255.255.255.0
     #> setenv serverip 192.168.1.100
     #> setenv bootfile lede-ar71xx-nand-c-60-initramfs-kernel.bin
     #> tftpboot
     #> bootm

  2. Wait for the C-60 to boot LEDE.
     On the root prompt. Enter:
     # ubiformat /dev/mtd4
     # ubiattach -p /dev/mtd4

  3. After that copy the sysupgrade.tar onto the router and run:
     # sysupgrade sysupgrade.tar

     to flash the image.

Special thanks to Chris Blake <chrisrblake93@gmail.com>. He provided
a C-60 unit and he helped with debugging the switch, LEDs and platfrom
support.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-10-15 11:36:50 +02:00
Florian Beier
5abeba3450
ar71xx: add userspace support for D-Link DIR-869 A1, generate images
Signed-off-by: Florian Beier <beier.florian@gmail.com>
[Matthias Schiffer: fix factory image, improve commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-11 22:58:37 +02:00
Piotr Dymacz
6e58440fc1 ar71xx: base-files: cleanups in etc/board.d/01_leds
This includes:

- use of local 'board' variable in LED names, wherever possible
- merge of boards with exactly the same LED configuration

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
c142df3094 ar71xx: fix LED names for GL Innovations boards
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
8689078a9b ar71xx: base-files: fix code style in etc/board.d/01_leds
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
edcdb93467 ar71xx: base-files: fix boards order in etc/board.d/02_network
Keep everything in alphabetical order. Boards are ordered in two steps,
first within/inside common configuration (case section), then sections,
globally.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:49 +02:00
Piotr Dymacz
a75cfac1f6 ar71xx: base-files: cleanups in etc/board.d/02_network
This includes:

- code style fixes
- removal of huge comment (it should be in doc, not here) and some small ones
- removal of redundant config for DR531/WPJ531 as the default is the same
- merge of boards with exactly the same interfaces config

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:49 +02:00
Piotr Dymacz
4fa90c49c1 ar71xx: base-files: rework etc/board.d/02_network
Convert etc/board.d/02_network in ar71xx target to the same shape
as we have in ramips target. Split code into two new functions:

- interface/s setup in ar71xx_setup_interfaces()
- MAC/s setup in ar71xx_setup_macs()

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:48 +02:00
Chris Blake
68d649f5cd ar71xx: add support for Cisco Meraki Z1 Cloud Managed Teleworker Gateway
This patch adds support for Cisco's Z1.
Detailed instructions for the flashing the device can
be found in the OpenWrt wiki:
<https://wiki.openwrt.org/toh/meraki/z1>

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-09-27 17:50:22 +02:00
Mathias Kresin
c1578d4fc9 cleanup ucidef_set_interface* usage
- quote the interface name
- remove call of not existing function
- remove the proto if it's the default proto

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-10 15:32:25 +02:00
Piotr Dymacz
f478fba663 ar71xx: add support for Zbtlink ZBT-WE1526
Zbtlink ZBT-WE1526 is based on Qualcomm Atheros QCA9531 v2.
Short specification:

- 650/400/200 MHz (CPU/DDR/AHB)
- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- two external, non-detachable antennas
- 8x LED, 1x button
- UART header (pinout: VCC, RX, TX, GND)

Flash instruction:

Use sysupgrade in vendor firmare which is based on OpenWrt.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-08-18 09:49:18 +02:00
Matthias Schiffer
adbbfb7ff9
ar71xx: don't use D-Link DIR-505 status LED as ethernet indicator
The stock firmware uses the single LED as status indicator only. Using the
same LED both for status and as ethernet indicator is uncommon, and has
been confusing users who were using the device as a WLAN mesh node (so the
LED was just off, as no ethernet was connected).

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-07-28 15:59:04 +02:00
Zhao Gang
42305ae24a ar71xx: add support for gl-mifi
This add initial support for gl-mifi.
Product page: http://www.gl-inet.com/mifi/

Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
2016-07-24 06:38:30 +02:00
Jo-Philipp Wich
e633a1b48f ar71xx: fix default network config of WZR-HP-G300NH and CR3000
The network defaults for the WZR-HP-G300NH and CR3000 models wrongly set the
lan interface to a vlan tagged device while the switch was set up in untagged
mode, leading to broken lan side ethernet connectivity by default.

Fix the issue by emitting untagged interfaces, consistent with the switch
setting on the device.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-07-20 00:21:48 +02:00
Zhao Gang
d963ddf042 ar71xx: add support for gl-ar300m
This add initial support for gl-ar300m router.
Product page: http://www.gl-inet.com/ar300m/

Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
2016-07-20 00:21:48 +02:00
Piotr Dymacz
d2c9b169b3 ar71xx: add support for jjPlus JWAP230
jjPlus JWAP230 is based on Qualcomm Atheros QCA9558 + QCA8337.
Short specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 2x 10/100/1000 Mbps Ethernet
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz with external PA (SST12LP15A), up to 28 dBm
- 3x MMCX connectors
- power input: 802.3at PoE or wide range DC (36-57 V)
- optional 802.3af PSE
- 1x mini-PCIe connector with PCIe, USB buses and SIM slot
- 1x mini-PCIe connector with PCIe bus
- 1x USB type-A connector
- 6x LED, 1x button (hardware reset)
- RS232 (MAX3223) and (E)JTAG headers

Default configuration:

- WAN on eth1 (RJ45 near LEDs with PoE input)
- LAN on eth0 (RJ45 near DC jack)
- left top LED set to be status LED
- all LEDs configurable form user space

Flash instruction (do it under U-Boot, using RS232):

1. tftp 0x80060000 lede-ar71xx-generic-jwap230-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-07-13 20:03:10 +02:00
Piotr Dymacz
e767980eb8 ar71xx: add support for Wallys DR531
Wallys DR531 is based on Qualcomm Atheros QCA9531 v2.
Short specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SE2576L), up to 30 dBm
- 2x MMCX connectors
- mini-PCIe connector with PCIe/USB buses and SIM slot
- 7x LED, 1x button, 1x optional buzzer
- UART, (E)JTAG and LED headers

Default configuration:

- WAN on eth1 (RJ45 near DC jack)
- LAN on eth0 (RJ45 near button)
- S4 LED set to be status LED
- all LEDs configurable form user space
- button configured for reset

Flash instruction (do it under U-Boot, using UART):

1. tftp 0x80060000 lede-ar71xx-generic-dr531-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-07-13 20:03:10 +02:00
David Pinilla Caparrós
bbbe9932e3 ar71xx: WDR4300: Fixed default VLAN order
Reordered the VLANs so the LAN ports are set to VLAN 1 and the WAN port is set to VLAN 2, as in the other routers in the config file. Moreover, this model had this VLAN mapping in OpenWRT Chaos Calmer. It seems that the VLAN were switched when fixing a bug in the port mapping ( OpenWRT changeset 47799 )

Signed-off-by: David Pinilla Caparrós <dpinitux@gmail.com>
2016-06-17 04:13:07 +02:00
Allan Nick Pedrana
e61fe4e4d7 ar71xx: add support for OpenEmbed SOM9331
This patch adds the target profile SOM9331 and configures hardware
functionality for the 3x Eth Ports & corresponding LED's, the USB Host,
the USART to USB bridge and the System LED.

Signed-off-by: Allan Nick Pedrana <nik9993@gmail.com>
2016-06-07 11:21:55 +02:00
KeLei Liang
563e9d5e1b ar71xx: add WRTnode2Q support
Signed-off-by: KeLei Liang <xzmu@wrtnode.com>
2016-06-06 14:58:11 +02:00
Stijn Segers
d2a91f9853
ar71xx: Fix TL-WR841N v11 LEDs, use separate machine
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2016-05-31 17:36:51 +02:00
Cezary Jackiewicz
71e0ef3978 ar71xx: add GPIO pin for usb power switch for RouterBOARD 912
RB912 has one usb shared between external USB and miniPCIe slot. GPIO52 can
reroute power to external USB (=1) or internal miniPCIe slot (=0)

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-05-27 10:27:44 +02:00
Alexander Couzens
c5ff273d85 ar71xx/cpe510: split profile into 2 profiles cpe210 and cpe510
Split profile into 2GHz and 5GHz. The 5GHz devices are
quite "special". The 2 GHz works perfect.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-05-23 13:39:49 +02:00
Sven Eckelmann
58dc285cd6 ar71xx: add user-space support for the OpenMesh MR1750v2
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:25 +02:00
Sven Eckelmann
e10d12411c ar71xx: add user-space support for the OpenMesh OM2P-HSv3
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:23 +02:00
Cezary Jackiewicz
0b45bec22c
ar71xx: add support for TP-LINK TL-WR842N/ND v3
- CPU QCA9531-BL3A
- RAM: 64MB
- flash: 16MB
- USB

AP143 platform, similar to tl-wr841n v10/v11, but with USB

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-05-14 21:45:16 +02:00
P.Wassi
8307c2fe68 ar71xx: Add support for Ubiquiti UniFi AP AC PRO
Add support for the Ubiquiti UniFi AP AC PRO
Signed-off-by: P.Wassi <p.wassi at gmx.at>
2016-05-12 03:29:36 +02:00
P.Wassi
c855e70491 ar71xx: Rename unifiac to unifiac-lite
To avoid confusion with different unifiac devices, rename existing target
"unifiac" to "unifiac-lite", before "unifiac-pro" is introduced.

Signed-off-by: P.Wassi <p.wassi at gmx.at>
2016-05-12 03:29:36 +02:00
blogic
75629fb2a8 ar71xx: add TP-Link TL-WR810N support
This patch adds support for the TP-Link TL-WR810N.
https://wiki.openwrt.org/toh/tp-link/tl-wr810n

Signed-off-by: Jens Steinhauser <jens.steinhauser@gmail.com>

SVN-Revision: 49286
2016-05-10 10:43:12 +02:00
John Crispin
ee53a240ac ar71xx: Add support for the OMYlink OMY-G1
https://wiki.openwrt.org/toh/omylink/omy-g1

http://www.omylink.com/

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 49258
2016-04-26 11:44:36 +00:00
John Crispin
5f1a82ec4f ar71xx: add TP-Link TL-WA901ND-v4 support
Signed-off-by: Tiziano Bacocco <tizbac2@gmail.com>

SVN-Revision: 49158
2016-04-09 10:26:46 +00:00
John Crispin
d9799dea89 ar71xx: add support for Compex WPJ342
OpenWrt can be flashed with following uboot commands:

tftpboot 0x80500000 openwrt-ar71xx-generic-wpj342-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize

Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 49157
2016-04-09 10:26:41 +00:00
John Crispin
2fa2d97ae2 ar71xx: add user-space support for the OpenMesh OM5P-AC
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49142
2016-04-09 10:25:51 +00:00
John Crispin
ba2d1ccffa ar71xx: WNR2200: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR2200 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 49101
2016-04-01 07:11:34 +00:00
Luka Perkov
ebaba15331 ar71xx: add support for ap120c
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 49082
2016-03-23 22:31:38 +00:00
John Crispin
5b2d89f060 ar71xx: WNR1000v2: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR1000v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 49076
2016-03-23 12:52:35 +00:00
John Crispin
3fd98db818 ar71xx: Add support for the OMYlink OMY-X1
This patch adds support for the OMYlink OMY-X1

https://wiki.openwrt.org/toh/omylink/omy-x1

http://www.omylink.com/

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 49026
2016-03-16 09:26:58 +00:00
John Crispin
346b1905fb ar71xx: add support for the Telldus TellStick ZNet Lite
Signed-off-by: Micke Prag <micke.prag@telldus.se>

SVN-Revision: 48977
2016-03-10 19:07:26 +00:00
Felix Fietkau
3f971c0dc8 ar71xx: WNR612v2: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR612v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48924
2016-03-05 09:45:15 +00:00
Felix Fietkau
94b8a6b5cf ar71xx: WNR2000v3: add speed_mask to Ethernet port LED initialization
This patch add speed_mask parameter to Ethernet port LED initialization
during system startup. LEDs are configured to show amber light for 10 Mbps
link and green for 100 Mbps as described on device label.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48923
2016-03-05 09:45:10 +00:00
Felix Fietkau
53b3872ddf ar71xx: WNR2000v3: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR2000v3 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48922
2016-03-05 09:45:06 +00:00
John Crispin
cede06cebc ar71xx: Support for Ubiquiti UniFi AP AC LITE
Add support for the Ubiquiti UniFi AP AC LITE
Signed-off-by: P.Wassi <p.wassi at gmx.at>

SVN-Revision: 48711
2016-02-12 08:31:32 +00:00
John Crispin
d6cb792d21 ar71xx: Added support for TL-WA801NDv3
Signed-off-by: Tiziano Bacocco <tizbac2@gmail.com>

SVN-Revision: 48705
2016-02-12 08:30:28 +00:00
John Crispin
9df952742d ar71xx: board.d: fix switch defaults on dLAN pro 1200+ WiFi ac
transparent for vlans as originally committed

Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>

SVN-Revision: 48358
2016-01-19 10:16:20 +00:00
John Crispin
ed72c5f846 ar71xx: add support for Netgear WPN824N
Add support for Netgear WPN824N.
Hardware specs:
  * AR7240, 4 LAN ports, 1 WAN port
  * AR9285 WLAN
  * 32 MB RAM
  * 4 MB Flash
  * 16 LEDs (LAN, WAN and Power/Status contain two LEDs for dual color
    effect)
  * 3 Buttons (not supported)

Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>

SVN-Revision: 48356
2016-01-19 10:16:04 +00:00
Felix Fietkau
826cfa5773 ar71xx: fix ap152 support
- ethernet gigabit pll
- switch configuration
- sysupgrade

Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 48187
2016-01-10 17:19:34 +00:00
John Crispin
9242d27b4a V2 ar71xx : Add Support for the Bitmain Antrouter R1
This patch adds support for the Bitmain Antrouter R1

http://wiki.openwrt.org/toh/bitmain/r1

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 48058
2016-01-01 21:21:13 +00:00
John Crispin
772f9d4e32 ar71xx: Add support for AirTight Networks C-55
This patch is to add support for the AirTight Networks C-55 Access Point

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47973
2015-12-23 14:43:35 +00:00
Felix Fietkau
fb1273dfdd ar71xx: PowerCloud CR5000 openwrt configuration
OpenWrt configuration part of support for the PowerCloud Systems
CR5000.  The CR5000 is a dual-band 802.11n wireless router with
8MB flash, 64MB RAM, (unused on stock firmware) USB 2.0 port and
five port gigabit ethernet switch.  The CR5000 was sold as
hardware for the Skydog cloud-managed router service.

    Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>

SVN-Revision: 47946
2015-12-19 11:28:18 +00:00
Felix Fietkau
59fc337a9a ar71xx: PowerCloud CR3000 OpenWrt configuration
OpenWRt configuration part of support for the PowerCloud
Systems CR3000.  The CR3000 is a 802.11n 2.4 GHz wireless router with
8MB flash, 64MB RAM, a four port gigabit ethernet switch, and a fast
ethernet wan port that was sold by PowerCloud Systems as
hardware for the Skydog cloud-managed router service.

Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>

SVN-Revision: 47945
2015-12-19 11:28:12 +00:00
Felix Fietkau
abc1faad0b ar71xx: PowerCloud CAP324 OpenWrt configuration
Openwrt configuration part of support for PowerCloud CAP324
Cloud AP.  The CAP324 Cloud AP is a device sold by PowerCloud Systems
who's stock firmware (CloudCommand) provides 'cloud' based managment
of large numbers access points.

The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port.  It can be powered via PoE
or a wall wart.

Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>

SVN-Revision: 47944
2015-12-19 11:27:59 +00:00
John Crispin
1f71f2220d ar71xx: add support for TRENDnet TEW-823DRU
Add support for TRENDnet TEW-823DRU:
- cpu: QCA9558 @720MHz
- flash: 16MB
- ram: 256MB
- 4+1 RJ45 100/1000Mbps
- wifi:  QCA9558 (bgn) and QCA9880-BR4A (ac)
- 1x USB 2.0

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 47927
2015-12-17 09:30:05 +00:00
John Crispin
abc84551c0 ar71xx: add support for Cisco's MR18
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47878
2015-12-12 06:42:29 +00:00
Jo-Philipp Wich
67e1c87012 all: drop old uci-defaults.sh
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47867
2015-12-11 15:26:06 +00:00
John Crispin
eb8ff56684 ar71xx: Add support for Wallys DR344
This patch is for Wallys DR344 support under OpenWRT

Signed-off-by: Philippe Duchein <wireless-dev@duchein.net>

SVN-Revision: 47847
2015-12-11 15:04:47 +00:00
Felix Fietkau
e4fd0a41fd ar71xx: fix switch port mapping for tl-wdr4300/3600
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47799
2015-12-06 14:25:36 +00:00
Jo-Philipp Wich
cc59f31e44 ar71xx: convert gpio switch config to board.d
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47763
2015-12-04 15:02:42 +00:00
Jo-Philipp Wich
08848936dd all: remove redundant board.d/00_model files
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47753
2015-12-04 11:07:06 +00:00
Jo-Philipp Wich
527ec2af59 all: remove dummy ucidef_set_interface_loopback() from board.d
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47744
2015-12-03 23:13:00 +00:00
Jo-Philipp Wich
feb8bf5ddc ar71xx: board.d: add missing include (#21296)
Include /lib/functions/system.sh in 02_network to define missing
mtd_get_mac_binary() procedure.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47723
2015-12-03 19:23:44 +00:00
Jo-Philipp Wich
8f8b702f85 board.d: remove redundant ucidef_set_interfaces_lan_wan() calls
This removes calls to ucidef_set_interfaces_lan_wan() and
ucidef_set_interfaces_lan() on boards where all relevant info can be
inferred from the switch definition.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47722
2015-12-03 17:30:56 +00:00
Jo-Philipp Wich
9b02e73188 board.d: merge ucidef_add_switch() and ucidef_add_switch_ports()
This changes uci-defaults-new.sh, config_generate and all relevant board.d
files in order combine ucidef_add_switch() and ucidef_add_switch_ports() into
a single function.

Also removes now superfluous enable and reset arguments.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47721
2015-12-03 17:30:24 +00:00
Jo-Philipp Wich
d17a64c7c0 base-files: uci-defaults-new: remove reset/enable args of ucidef_add_switch()
Out of 69 switch definitions, only 3 pass something different than "1" as
values for reset and enable, with one of those three being invalid.

This change ...

 * removes the reset and enable arguments from ucidef_add_switch()
 * unconditionally writes reset:1 and enable:1 to JSON
 * converts the three users of nonstandard values to ucidef_add_switch_attr()

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47720
2015-12-03 17:30:08 +00:00
Jo-Philipp Wich
81f603dfb8 ar71xx: record board id and model name in /etc/board.json
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47672
2015-11-30 10:17:20 +00:00
Jo-Philipp Wich
963fc89df2 ar71xx: switch network and led defaults to board detection framework
Also translate ucidef_add_switch_vlan() to ucidef_add_switch_ports() for better
switch topology mapping and improved default config generation.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47663
2015-11-26 14:42:28 +00:00
Jo-Philipp Wich
3fac6dde85 Revert "ar71xx: migrate led and network setup to board detection framework"
The board detect code needs more fixes in order to work properly.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47641
2015-11-25 11:53:59 +00:00
John Crispin
1a092ce0e0 ar71xx: add GL-Domino Pi support V3
This is the patch for GL-Domino Pi V3. Updated against the latest trunk.

Signed-off-by: alzhao<alzhao@gmail.com>

SVN-Revision: 47622
2015-11-24 18:30:50 +00:00
John Crispin
a04c3e73a3 ar71xx: add GL-AR300 support V3
This is the patch for GL-AR300 V3, tested against the latest trunk.

Signed-off-by: alzhao<alzhao@gmail.com>

SVN-Revision: 47621
2015-11-24 18:30:19 +00:00
John Crispin
72093bd528 ar71xx: add GL-AR150 support V3
This is the 3rd version. Modified against the latest trunk.

Signed-off-by: alzhao<alzhao@gmail.com>

SVN-Revision: 47620
2015-11-24 18:29:59 +00:00
Jo-Philipp Wich
7fc4a4581b ar71xx: fix network default config of the TEW-732BR
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47595
2015-11-22 20:00:13 +00:00
John Crispin
99fd9a7041 ar71xx: add support for the devolo dLAN Hotspot
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>

SVN-Revision: 47554
2015-11-21 21:24:18 +00:00
Jo-Philipp Wich
ade2c06d61 ar71xx: migrate led and network setup to board detection framework
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47534
2015-11-20 22:14:36 +00:00