The nand driver normally while waiting for the device to become ready;
this is normally fine, but xway_nand holds the ebu_lock spinlock, and
this can cause lockups if other threads which use ebu_lock are
interleaved. Fix this by waiting instead of polling.
This mainly showed up as crashes in ath9k_pci_owl_loader (see
https://github.com/openwrt/openwrt/issues/9829 ), but turning on
spinlock debugging shows this happening in other places too.
This doesn't seem to measurably impact boot time.
Tested on bt_homehub-v5a with 5.10 and 5.15.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
[Add commit description into patch]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The AVM FRITZ!Box 7330 shares hardware with the AVM Fritzbox 7320
except for the second ethernet port, which only supports 100M.
Hardware:
- SoC: Lantiq ARX 188
- CPU: 2x MIPS 34Kc 393 MHz
- RAM: 64 MiB 196 MHz
- Flash: 16 MiB NAND
- Ethernet: Built-in Gigabit Ethernet switch, 1x 1GbE, 1x 100M
- Wifi: Atheros AR9227-BC2A b/g/n with 2 pcb/internal antennas
- USB: 2x USB 2.0
- DSL: Built-in ADSL2+ modem
- DECT: Dialog SC14441
- LEDs: 1 two-color, 4 one-color
- Buttons: 1x DECT, 1x WIFI
- Telephone connectors: 1 FXS port via TAE or RJ11 connector
Installation:
The installation process is described on the wiki.
Unsupported (same as AVM 7320):
- VoIP (DECT and FXS),
- Second Ethernet port.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
this was thoroughly tested (warm and cold boots). on a
real 7360v2. This is because there have been documented
hick-ups with other lantiq devices that need the
owl-loader too.
It's likely that the 7360(sl) could be converted in the
same way as well. However the 7362sl uses a reversed
caldata format, so the "qca,no-eeprom" stays in place.
The patch also moves the urloader nvmem partition
definition into the partition section.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Manually rebased:
ramips/patches-5.10/810-uvc-add-iPassion-iP2970-support.patch
All other patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
This commit adds the PHY reset gpio for the LAN1 port to the dts.
According to the GPL sources, gpios 34 and 36 are used on the AVM
FritzBox 7320 and 7330. The second port is unsupported.
The gpio assignment has been verified on the FritzBox 7330.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
The WIFI LED already worked for me with the latest openwrt 22.03 version.
Wifi LED did not with an older 22.x version (in gluon - there phy0radio did nothing but phy0tpt did show activity
the WAN interface has the name "wan" and not "pppoe-wan" on this device
fixes#7757 (and FS#2987)
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Removed upstreamed:
pending-5.15/101-Use-stddefs.h-instead-of-compiler.h.patch[1]
ipq806x/patches-5.15/122-01-clk-qcom-clk-krait-fix-wrong-div2-functions.patch[2]
bcm27xx/patches-5.15/950-0198-drm-fourcc-Add-packed-10bit-YUV-4-2-0-format.patch[3]
Manually rebased:
ramips/patches-5.15/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch[4]
Added patch/backported:
ramips/patches-5.15/107-PCI-mt7621-Add-sentinel-to-quirks-table.patch[5]
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=c160505c9b574b346031fdf2c649d19e7939ca11
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=a051e10bfc6906d29dae7a31f0773f2702edfe1b
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=ec1727f89ecd6f2252c0c75e200058819f7ce47a
4. Quilt gave this output when I applied the patch to rebase it:
% quilt push -f
Applying patch platform/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch
patching file arch/mips/ralink/Kconfig
patching file drivers/pci/controller/Kconfig
patching file drivers/pci/controller/Makefile
patching file drivers/staging/Kconfig
patching file drivers/staging/Makefile
patching file drivers/staging/mt7621-pci/Kconfig
patching file drivers/staging/mt7621-pci/Makefile
patching file drivers/staging/mt7621-pci/TODO
patching file drivers/staging/mt7621-pci/mediatek,mt7621-pci.txt
patching file drivers/staging/mt7621-pci/pci-mt7621.c
Hunk #1 FAILED at 1.
Not deleting file drivers/staging/mt7621-pci/pci-mt7621.c as content differs from patch
1 out of 1 hunk FAILED -- saving rejects to file drivers/staging/mt7621-pci/pci-mt7621.c.rej
patching file drivers/pci/controller/pcie-mt7621.c
Applied patch platform/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch (forced; needs refresh)
Upon inspecting drivers/staging/mt7621-pci/pci-mt7621.c.rej, it seems that
the original patch wants to delete drivers/staging/mt7621-pci/pci-mt7621.c
but upstream's version was not an exact match. I opted to delete that
file.
5. Suggestion by hauke: 19098934f9
"This patch is in upstream kernel, but it was backported to the old
staging driver in kernel 5.15."
Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Signed-off-by: John Audia <therealgraysky@proton.me>
Reported by user: missing driver for USB; add to image definition
https://github.com/openwrt/openwrt/issues/11326Resolves: #11326
Signed-off-by: Tony Butler <spudz76@gmail.com>
Acked-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Enabled CONFIG_MIPS_MT_SMP and CONFIG_SCHED_SMT.
Tested on FRITZ!Box 7330 SL, 7312 and o2 Box 4421.
Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Fixes leftover TODO from commit 6bf179b270
Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Run of 'make kernel_oldconfig CONFIG_TARGET=subtarget'
Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Add 6.1 tag to upstream patch now that 6.1 got tagged. This permits to
track patch in a better way and directly drop them on kernel bump.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
0001-MIPS-lantiq-add-pcie-driver.patch needs to drop
MODULE_SUPPORTED_DEVICE because that macro is gone on newer kernels.
Add checks for copy_{to,from}_user in
0008-MIPS-lantiq-backport-old-timer-code.patch which is now mandatory.
0705-v5.13-net-dsa-lantiq-allow-to-use-all-GPHYs-on-xRX300-and-.patch
get dropped because it's a backport from Linux 5.13.
All other patches are refreshed.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This comit fixes warnings that occur on kernel 5.15:
...
[ 2.269736] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6 1e108000.switch-mii:00:
PHY has delays (e.g. via pin strapping), but phy-mode = 'rgmii'
[ 2.269736] Should be 'rgmii-id' to use internal delays txskew:1500 ps rxskew:1500 ps
...
Ref: be393dd685
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
The CPU port should define the phy-mode and and a PHY phandle or
fixed-link to indicate how the CPU port is connected to the SoC's
Ethernet controller. On xRX200 this is all internal connection, so use
phy-mode = "internal" along with a fixed-link that matches the
definition inside ð0.
Linux 6.0 shows a warning since upstream commit e09e9873152e3f ("net:
dsa: make phylink-related OF properties mandatory on DSA and CPU
ports"). when these properties are missing. Adding the properties
before OpenWrt is updated to Linux 6.0 is harmless.
Suggested-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This patch is needed to handle interrupts by the second VPE on the Lantiq
ARX100, xRX200, xRX300 and xRX330 SoCs. Switching some ICU interrupts to
the second VPE results in a hang. Currently, the vsmp_init_secondary()
function is responsible for enabling these interrupts. It only enables
Malta-specific interrupts (SW0, SW1, HW4 and HW5).
The MIPS core has 8 interrupts defined. On Lantiq SoCs, hardware
interrupts are wired to an ICU instance. Each VPE has an independent
instance of the ICU. The mapping of the ICU interrupts is shown below:
SW0(IP0) - IPI call,
SW1(IP1) - IPI resched,
HW0(IP2) - ICU 0-31,
HW1(IP3) - ICU 32-63,
HW2(IP4) - ICU 64-95,
HW3(IP5) - ICU 96-127,
HW4(IP6) - ICU 128-159,
HW5(IP7) - timer.
This patch enables all interrupt lines on the second VPE.
This problem affects multithreaded SoCs with a custom interrupt controller.
SOCs with 1004Kc core and newer use the MIPS GIC. At this point, I am aware
that the Realtek RTL839x and RTL930x SoCs may need a similar fix. In the
future, this may be replaced with some generic solution.
Tested on Lantiq xRX200.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This matches the scheme used by other target packages and will avoid
confusion with any future version.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Removed following upstreamed patch:
* bcm53xx: 081-next-ARM_dts_BCM53015-add-mr26.patch
All other patches automagically rebased.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
All targets expect the malta target already activate the CONFIG_GPIOLIB
option. Move it to generic kernel configuration and also activate it for
malta.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There are forum reports that 2 LAN ports are still not working,
the phy-mode settings are adjusted to fix the problem.
Fixes: #10371
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
There are forum reports that 2 LAN ports are not working, the
GPIO settings are adjusted to fix the problem.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
lantiq,bus-clock, interrupt-map-mask and interrupt-map are already
defined with these exact values in vr9.dtsi. Drop them from
vr9_tplink_tdw8980.dts to just have one place where these are
maintained.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This is now built-in, enable so it won't propagate on target configs.
Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca9367069 ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ar9.dtsi and danube.dtsi only have one reset controller and they are
naming it "reset". This is equivalent to "reset0" in vr9.dtsi. Fix the
references to the reset controller in the recently added PCI controller
reset line.
Fixes: 087f2cba26 ("lantiq: dts: Add the reset line for the PCI controller")
Reported-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
The PCI controller has it's reset line wired up to bit 13 of RCU.
Describe this in our .dtsi files.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
FRITZ!Box 7360 V2 and FRITZ!Box 7360 SL both use GPIOs 37 (for &phy0)
and GPIO 44 (for &phy1) to control the PHY's reset lines. FRITZ!Box 7362
SL however uses GPIO 45 (for &phy0) and GPIO 44 (for &phy1). Move the
GPIO reset definitions to each individual board .dts and while at it,
fix the GPIOs for the FRITZ!Box 7362 SL.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This commit replaces patch number 0703 with the upstream accepted
version. This patch requires backporting an additional patch to
avoid conflicts.
The only significant change is the lower maximum MTU. Packets with
lengths over 2400 may be dropped.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Without a partition subnode ofpart_core still parses direct subnodes as
partitions, but it ignores nodes with a compatible property. Due to
this, the switch to nvmem-cells made the urlader partition inaccessible.
As a result, the wireless network was broken, as the calibration data
is read from that partition by a script.
Fixes: #8983
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The &spi node has #address-cells = <1> and #size-cells = <0>. Drop the
extra 0 in the reg property from the SPI flash node to ensure it's
number of cells matches the definition in the parent node. This also
makes the reg property for the SPI flash node consistent with all other
VR9 boards.
Fixes: eae6cac6a3 ("lantiq: add support for AVM FRITZ!Box 7362 SL")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
The skb->len field is read after the packet is sent to the network
stack. In the meantime, skb can be freed. This patch fixes this bug.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
