This backports patches
leds: turris-omnia: convert to use dev_groups
leds: turris-omnia: Use sysfs_emit() instead of sprintf()
leds: turris-omnia: Drop unnecessary mutex locking
leds: turris-omnia: Do not use SMBUS calls
leds: turris-omnia: Make set_brightness() more efficient
leds: turris-omnia: Support HW controlled mode via private trigger
leds: turris-omnia: Add support for enabling/disabling HW gamma correction
leds: turris-omnia: Fix brightness setting and trigger activating
into backport-5.15.
The above patches replace:
leds: turris-omnia: support HW controlled mode via private trigger
leds: turris-omnia: initialize multi-intensity to full
leds: turris-omnia: change max brightness from 255 to 1
from mvebu/patches-5.15.
Signed-off-by: Marek Behún <kabel@kernel.org>
This reverts commit 0c117e1f6c.
Activate the lantiq/xrx200 target again.
There are still some problems with the GSWIP, but it is not leaking
packets to the wrong bridge in normal operations.
It shows some error messages at configuration like these:
[ 54.308861] gswip 1e108000.switch: port 5 failed to add ce:9d:84:d1:81:f0 vid 1 to fdb: -22
[ 54.325633] gswip 1e108000.switch: port 5 failed to add e8🇩🇪27:95:c1:b4 vid 0 to fdb: -22
[ 54.351242] gswip 1e108000.switch: port 5 failed to add e8🇩🇪27:95:c1:b4 vid 1 to fdb: -22
[ 54.358311] gswip 1e108000.switch: port 5 failed to delete ce:9d:84:d1:81:f0 vid 1 from fdb: -2
The problems are described in this pull request:
https://github.com/openwrt/openwrt/pull/13200
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With patch 101-03-spi-mtk_spim-get-spi-clk-rate-only-once.patch
a new system to calculate the SPI clocks has been added.
Unfortunately, the do_div macro overrides the global
priv->pll_clk_rate field. This will cause to have a reduced
clock rate on each subsequent SPI call.
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
Some packages (like wavemon >= 0.9.4) depend on libnl-cli. Add support
for this part of the lib. libnl-cli itself depends on libnl-genl and
libnl-nf. On MIPS, this component adds 81kB.
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
(punctuation correction and reorganisation of commit message)
Signed-off-by: Nick Hainke <vincent@systemli.org>
1) clear nvram partialboots upon successful boot
This behavior is already defined for EA9500; enabled for EA9200 too.
2) fix MAC address in board.d/02_network
Use the correct nvram variable to derive lan/wan MAC address.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
Set correct GPIO (10) for the WPS button. This matches GPIO settings in
vendor GPL sources. Note that GPL sources also mention a USB indicator
LED (GPIO 13) but the device has neither an external USB port nor a USB LED.
In addition, prefixes (button-, led-) are added to relevant DT entries,
as well as color and function specifications for LEDs.
Closes: #13736
Reported-by: Waldemar Czabaj <kaball@wp.pl>
Signed-off-by: Rani Hod <rani.hod@gmail.com>
(added led mitigations for wifi leds)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This backports patches
leds: turris-omnia: Use sysfs_emit() instead of sprintf()
leds: turris-omnia: Drop unnecessary mutex locking
leds: turris-omnia: Do not use SMBUS calls
leds: turris-omnia: Make set_brightness() more efficient
leds: turris-omnia: Support HW controlled mode via private trigger
leds: turris-omnia: Add support for enabling/disabling HW gamma correction
leds: turris-omnia: Fix brightness setting and trigger activating
into backport-6.1.
The above patches replace:
leds: turris-omnia: support HW controlled mode via private trigger
leds: turris-omnia: initialize multi-intensity to full
leds: turris-omnia: change max brightness from 255 to 1
from mvebu/patches-6.1.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
When using an external toolchain, ldd is not linked into the rootfs.
This causes subsequent upgrades to fail with 'Failed to exec upgraded'.
This patch adds the symlink when using an external toolchain and musl.
Signed-off-by: Arien Judge <arienjudge@outlook.com>
This is an RTL8382-based switch with 24 copper ports + 4 SFP ports
Specifications:
---------------
* SoC: Realtek RTL8382M
* Flash: 32 MiB SPI flash
* RAM: 256 MiB
* Ethernet: 24x 10/100/1000 Mbps
* Buttons: 1x "Reset" button
* UART: 1x serial header, unpopulated
* SFP: 4 SFP ports
Works:
------
- (24) RJ-45 ethernet ports
- Switch functions
- Buttons
- Sys LED on front panel (no port LEDs)
Not yet enabled:
----------------
- Port LEDs (no driver for RTL8231 in this mode)
- SFP cages (no driver for PHY)
Install via web interface:
-------------------------
Not supported at this time.
Install via serial console/tftp:
--------------------------------
The U-Boot firmware drops to a TP-Link specific "BOOTUTIL" shell at
38400 baud. There is no known way to exit out of this shell, and no
way to do anything useful.
Ideally, one would trick the bootloader into flashing the sysupgrade
image first. However, if the image exceeds 6MiB in size, it will not
work. To install OpenWRT:
Prepare a tftp server with:
1. server address: 192.168.0.146
2. the image as: "uImage.img"
Power on device, and stop boot by pressing any key.
Once the shell is active:
1. Ground out the CLK (pin 16) of the ROM (U6)
2. Select option "3. Start"
3. Bootloader notes that "The kernel has been damaged!"
4. Release CLK as soon as bootloader thinks image is corrupted.
5. Bootloader enters automatic recovery -- details printed on console
6. Watch as the bootloader flashes and boots OpenWRT.
Blind install via tftp:
-----------------------
This method works when it's not feasible to install a serial header.
Prepare a tftp server with:
1. server address: 192.168.0.146
2. the image as: "uImage.img"
3. Watch network traffic (tcpdump or wireshark works)
4. Power on the device.
5. Wait 1-2 seconds then ground out the CLK (pin 16) of the ROM (U6)
6. When 192.168.0.30 makes tftp requests, release pin 16
7. Wait 2-3 minutes for device to auto-flash and boot OpenWRT
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Like with some other ipq40xx devices, the kernel image size for the WPJ428
is limited in stock u-boot. For that reason, the current release doesn't
include an image for the board.
By switching to the zImage format, the kernel image size is reduced which
re-enables the build process. The image boots and behaved normally through
a few days of testing.
Before the switch to kernel version 6.1, it was possible to reduce the
image size by enough when disabling UBIFS and its otherwise unneeded
dependencies.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
prepend-dtb got extended to handle the Meraki devices too,
the problem here was that the Netgear WNDR4700 expects an
u-boot header in front of the DTB, whereas Meraki devices
don't.
Since the header was dropped, the WNDR4700's uboot started
to complain:
Bad Magic Number,it is forbidden to be written to flash!!
when flashing the factory.img since it expects an u-boot
header there.
Fixes: 5dece2d9355a ("apm821xx: switch over from DTB_SIZE to DEVICE_DTC_FLAGS")
Reported-by: @kisgezenguz
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Make use of new toolchain define. TOOLCHAIN_DIR should be used only for
toolchain related packages and for everything else TOOLCHAIN_ROOT_DIR
and other define should be used instead.
Switch to new entry where possible.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Make toolchain dirs define more consistent between internal and external
toolchains.
Make use of specific dirs also for intenral toolchain and generilize
include and lib inclusion.
Also set TOOLCHAIN_ROOT_DIR for internal toolchain as this is what
packages should use to reference staging toolchain directory.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some package may needs to enable compatibility option based on the GCC
version.
Currently the GCC version is set based on the default value and doesn't
actually reflect the real value provided by the external toolchain if
used.
Fix this by correctly detecting the GCC version in the external
toolchain and set the correct value in CONFIG_GCC_VERSION.
A new option is added in menuconfig to manually set the GCC version if
needed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some packages won't ever have something to patch as they normally
install files or are meta-packages.
For these special packages, disable QUILT refresh.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The option 31 in the RA specifies the DNS search list, the support
to configure this via UCI is missing in case dnsmasq-dhcpv6 is used.
This commit uses the uci option domain (same as is done by odhcpd) to
read and pass the DNS search list to dnsmasq, which is then used by RA.
Hence, with this commit, we are able to configure DNS search list for the
RA messages via the uci config when dnsmsaq-dhcpv6 is used.
Signed-off-by: Rahul Thakur <rahul.thakur@iopsys.eu>
Doing a simple ping to my device shows this:
64 bytes from 10.0.253.101: icmp_seq=1 ttl=64 time=2.00 ms
64 bytes from 10.0.253.101: icmp_seq=2 ttl=64 time=2.02 ms
64 bytes from 10.0.253.101: icmp_seq=3 ttl=64 time=1.68 ms
64 bytes from 10.0.253.101: icmp_seq=4 ttl=64 time=1.91 ms
64 bytes from 10.0.253.101: icmp_seq=5 ttl=64 time=1.92 ms
64 bytes from 10.0.253.101: icmp_seq=6 ttl=64 time=2.04 ms
Some users even report higher values on older kernels:
64 bytes from 192.168.1.10: seq=0 ttl=64 time=0.612 ms
64 bytes from 192.168.1.10: seq=1 ttl=64 time=2.852 ms
64 bytes from 192.168.1.10: seq=2 ttl=64 time=2.719 ms
64 bytes from 192.168.1.10: seq=3 ttl=64 time=2.741 ms
64 bytes from 192.168.1.10: seq=4 ttl=64 time=2.808 ms
The problem is that the governor is set to Ondemand, which causes
the CPU to clock all the way down to 48MHz in some cases.
Switching to performance governor:
64 bytes from 10.0.253.101: icmp_seq=1 ttl=64 time=0.528 ms
64 bytes from 10.0.253.101: icmp_seq=2 ttl=64 time=0.561 ms
64 bytes from 10.0.253.101: icmp_seq=3 ttl=64 time=0.633 ms
64 bytes from 10.0.253.101: icmp_seq=4 ttl=64 time=0.526 ms
In theory, using the Performance governor should increase power draw,
but it looks like it really does not matter for this soc.
Using a calibrated precision DC power supply (cpu idle):
Ondemand
24.00V * 0.134A = 3.216 Watts
48.00V * 0.096A = 4.608 Watts
Performance
24.00V * 0.135A = 3.240 Watts
48.00V * 0.096A = 4.608 Watts
Let's simply switch to the Performance governor by default
to fix the general jittery behaviour on devices using this soc.
Tested on: MikroTik wAP ac
Fixes: #13649
Reviewed-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
To support the IXP42x platforms we need a kernel module
for the Epson R7301 RTC so we can load it as an optional
module.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Robert Marko <robimarko@gmail.com>
To support the IXP42x platforms we need a kernel module
for the X1205 RTC so we can load it as an optional module.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Robert Marko <robimarko@gmail.com>
The lib-chacha20 library is missing build rules for big endian
ARM, and since IXP4xx is big endian ARM we need those rules to
build for IXP4xx.
Suggested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a partial revert of the deletion of the IXP4xx
target: we restore the APEX boot loader so we can use it
for the NSLU2 and related targets.
The APEX upstream is as dead as it gets so I have applied
OpenWrts old patches on top of the never released
v1.6.10 version and forked it into an OpenWrt variant
on GitHub. If the upstream comes back alive I will
happily switch over to it.
The file refers to the external GitHub, I suppose when
integrating this patch the file should be copied to OpenWrts
file repository and the file link changed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ucidef_set_network_device_* functions in uci-defaults.sh disagree
on whether to use "network-device" or "network_device" in board.json.
With the additional caveat that jshn will translate hyphens (-) into
underscores (_). This casues problems in netifd which expected
"network_device" causing boards which depend on assigning MACs in
board.json via uci-defaults.sh (or jshn in general) to fail.
This commit addresses the issue by using network_device in
uci-defaults.sh.
The bug was uncovered in the forums here:
https://forum.openwrt.org/t/support-for-rtl838x-based-managed-switches/57875/2596
This was exposed by commit 4ebba8a05d ("realtek: add support for HPE
1920-8g-poe+") where the board_config_load call from 03_gpio introduced
the key normalization by jshn.
Fixes: 9290539ca9 ("base-files: allow setting device and bridge macs")
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Michael 'ASAP' Weinrich <michael@a5ap.net>
[ improve commit title, description and fix wrong Tested-by tag ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Copy configuration to boot partition (partition 1) instead of root
partition (partition 2) because the root partition is not writable if
it's a suqashfs image.
Move configuration back to root during preinit.
Fixes: https://github.com/openwrt/openwrt/issues/13695
Signed-off-by: Christian Buschau <cbuschau@d00t.de>
479c7f8676d9 cache: make record/hostname lookup case-insensitive
26c97a5a50bf ubus: add a browse flag for suppressing cached ip addresses
c286c51a9bd9 Fix AVL tree traversal in cache_record_find and cache_host_is_known
4035fe42df58 interface: use a global socket instead of per-interface ones
c63d465698c7 cache: dump hostname target from srv records
b42b22152d73 use hostname from SRV record to look up IP addresses
d45c443aa1e6 ubus: add array flag support for the hosts method
Signed-off-by: Felix Fietkau <nbd@nbd.name>
At this moment, 702-phy-Add-2.5G-SGMII-interface-mode.patch cause error
durring kernel compilation:
CC drivers/net/phy/phylink.o
drivers/net/phy/phylink.c: In function 'phylink_get_capabilities':
drivers/net/phy/phylink.c:443:9: error: enumeration value 'PHY_INTERFACE_MODE_2500SGMII' not handled in switch [-Werror=switch]
443 | switch (interface) {
| ^~~~~~
cc1: all warnings being treated as errors
NXP take care of it. Let's port their patch.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Patches recreated from NXP 6.1 tree:
400-LF-20-3-mtd-spi-nor-Use-1-bit-mode-of-spansion-s25fs.patch
701-staging-add-fsl_ppfe-driver.patch
702-phy-Add-2.5G-SGMII-interface-mode.patch
Patch 703 includes changes made by Christian Marangi, extracted from commit
0d4a547905.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Some MT7915 devices need to load the second part of the eeprom to
work properly. The mt76 driver is not yet ready to read the pre-cal
data via the NVMEM cell. Therefore, partially revert commit to fix
the device probe issue on some devices.
P.S.
Except for D-Link and Ubnt devices, It is still uncertain whether
pre-cal data is required for other devices in the patch.
This partially reverts commit 9ac891f8c4.
Fixes: https://github.com/openwrt/openwrt/issues/13700
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Telco Electronics X1 has MT7603E and MT7612E PCIe NICs. They are
driven by kmod-mt7603 and kmod-mt76x2.
Ref: 73e0f52b6e ("ramips: add support for Telco Electronics X1")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The starting address of 'factory' partition is 0x40000, and the
starting address of the next partition is 0x50000. It's obvious
that the correct size for the 'factory' is 0x10000, just like
other MT7620 devices.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
These three devices uses MT7612E PCIe NIC and supported by the
'mt76' driver. So the right frequency limit property should be
`ieee80211-freq-limit`.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
On the ramips target, all 'wmac' nodes in SoC dtsi are enabled by
default except mt7628. There is no need to mark them as 'okay'
again. So these useless properties can be removed.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch converts MT761{0,2,3} PCIe WiFi calibration data to NVMEM
format for legacy Ralink SoCs (MT7620 and Mt7628). The EEPROM size of
the MT7610 and MT7612 is 0x200. there are only three devices uses
MT7613 NIC, ASUS RT-AC1200 V2, COMFAST CF-WR758AC V2 and Keenetic
KN-1613. The EEPROM size of them is 0x4da8.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch converts legacy Ralink SoCs and MT7620 WiFi calibration
data to NVMEM format. The EEPROM size is 0x200.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
