Add pending patch fixing binfmt compilation warning on some arch.
This fix compilation warning:
fs/binfmt_elf.c: In function 'parse_elf_properties.isra':
fs/binfmt_elf.c:821:1: error: the frame size of 1040 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
821 | }
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning:
drivers/pinctrl/bcm/pinctrl-bcm4908.c: In function 'bcm4908_pinctrl_probe':
drivers/pinctrl/bcm/pinctrl-bcm4908.c:541:53: error: passing argument 3 of 'pinmux_generic_add_function' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
541 | function->groups,
| ~~~~~~~~^~~~~~~~
In file included from drivers/pinctrl/bcm/pinctrl-bcm4908.c:16:
drivers/pinctrl/bcm/../pinmux.h:153:46: note: expected 'const char **' but argument is of type 'const char * const*'
153 | const char **groups,
| ~~~~~~~~~~~~~^~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Current gcc set a limit for each stack and complain if this limit is not
followed. JFSS2 in build_xattr function currently exceed the limit by
allocating a massive array of struct of 128 elements. Introduce a
pending patch that allocate this temp array dynamically fixing the
compilation warning:
fs/jffs2/xattr.c: In function 'jffs2_build_xattr_subsystem':
fs/jffs2/xattr.c:887:1: error: the frame size of 1088 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
887 | }
| ^
Affecting many target that require jffs2 support.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop unused res variable from pci ar724x OF convert patch fixing
compilation warning:
arch/mips/pci/pci-ar724x.c: In function 'ar724x_pci_probe':
arch/mips/pci/pci-ar724x.c:387:26: error: unused variable 'res' [-Werror=unused-variable]
387 | struct resource *res;
| ^~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Upstream commit ("net: phylink: add generic validate implementation") was
backported, however PSGMII PHY mode patch for ipq40xx was not updated to
add PSGMII to phylink_get_linkmodes() so the following warning would be
printed during kernel compilation:
drivers/net/phy/phylink.c: In function 'phylink_get_linkmodes':
drivers/net/phy/phylink.c:360:9: error: enumeration value 'PHY_INTERFACE_MODE_PSGMII' not handled in switch [-Werror=switch]
360 | switch (interface) {
| ^~~~~~
Resolve the warning by adding the PSGMII mode to phylink_get_linkmodes().
Signed-off-by: Robert Marko <robimarko@gmail.com>
Handle error from device reset in SPI ralink driver fixing compilation
warning:
drivers/spi/spi-rt2880.c: In function 'rt2880_spi_probe':
drivers/spi/spi-rt2880.c:474:17: error: ignoring return value of 'device_reset' declared with attribute 'warn_unused_result' [-Werror=unused-result]
474 | device_reset(&pdev->dev);
| ^~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop unused res variable from pci ar71xx OF convert patch fixing
compilation warning:
arch/mips/pci/pci-ar71xx.c: In function 'ar71xx_pci_probe':
arch/mips/pci/pci-ar71xx.c:287:26: error: unused variable 'res' [-Werror=unused-variable]
287 | struct resource *res;
| ^~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning from mangle bootargs patch. Now that we flag
warning as error these cause compilation error.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
From 5.15 and up linux kernel introduced CONFIG_WERROR to flag any
warning as error. To improve code quality, enable this by default to
catch any warning and fix it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 91e3419a33.
Now that squashfs3-lzma generates reproducible output we can drop the
empty binary. Having a binary file in the tree is not nice and we actually
also use squashfs3-lzma for devices which expect the kernel to be loaded
from a squashfs3...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Apply the same LED configuration used by the vendor-firmware for the
GPY211 controlled WAN LED in OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
As we can now configure the switch LED configuration, write the switch
LED configuration values from the vendor firmware to the switch-IC.
Previously, the switch-LEDs did not show any acitvity or link-status
whatsoever.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds a small hack similar to the one used for ar8xxx switches to
read a reg:value map for configuring the LED configuration registers.
This allows OpenWrt to write device-specific LED action as well as blink
configurations. It is unlikely to be accepted upstream, as upstream
plans on integrating their own framework for handling these LEDs.
Signed-off-by: David Bauer <mail@david-bauer.net>
The MT753x switches provide a switch-internal MDIO bus for the embedded
PHYs.
Register a OF sub-node on the switch OF-node for this internal MDIO bus.
This allows to configure the embedded PHYs using device-tree.
Signed-off-by: David Bauer <mail@david-bauer.net>
Fix following error when building 32bit arm targets with kmod-crypto-sha512
ERROR: module '/home/user/openwrt/build_dir/target-arm_xscale_musl_eabi/linux-kirkwood_generic/linux-5.15.109/arch/arm/crypto/sha512-arm.ko' is missing.
Signed-off-by: Lu jicong <jiconglu58@gmail.com>
Hardware specification:
- SoC: MediaTek MT7621AT (880 MHz)
- Flash: 16 MB (Macronix MX25L12835FM2I-10G)
- RAM: 128 MB (Nanya NT5CC64M16GP-DI)
- WLAN 2.4 GHz: 2x2 MediaTek MT7603EN
- WLAN 5 GHz: 2x2 MediaTek MT7615N
- Ethernet: 1x 10/100/1000 Mbps
- LED: Power, Wifi, WPS
- Button: Reset, WPS
- UART: 1:VCC, 2:GND, 3:TX, 4:RX (from LAN port)
Serial console @ 57600,8n1
Flash instructions:
Connect to serial console and start up the device. As the bootloader got
locked you need to type in a password to unlock U-Boot access.
When you see the following output on the console:
relocate_code Pointer at: 87f1c000
type in the super secure password:
1234567890
Then select TFTP boot from RAM by selecting option 1 in the boot menu.
As Linksys decided to leave out a basic TFTP configuration you need to
set server- & client ip as well as the image filename the device will
search for. You need to use the initramfs openwrt image for the TFTP
boot process.
Once openwrt has booted up, upload the sysupgrade image via scp and run
sysupgrade as normal.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
The previously stated speed of sdr-104 in is too high for the hardware
to reliably communicate with some fast SD cards.
Rockchip boards have a common bug when operating uhs speed, which will
hang the system during a soft reboot.
To be on the safe side, lower the speed to workaround.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware
--------
RockChip RK3328 ARM64 (4 cores)
4GB DDR4 RAM
1x 1000 Base-T
2 LEDs (POWER / USER)
HDMI 2.0
3.5mm TRRS AV jack
Micro-SD slot
eMMC slot
1x USB 3.0 Port
2x USB 2.0 Port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card using
dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The filesystem is currently created on every build to trick the boot
loader of some FRITZ! devices into accepting the image. Sadly the
resulting squashfs-lzma filesystem is not reproducible. To fix this,
create a squashfs filesystem once and include it into the repository.
Creation happend as shown below
rm -rf empty_dir
mkdir empty_dir
./staging_dir/host/bin/mksquashfs-lzma \
empty_dir/ empty-squashfs-lzma \
-noappend -root-owned -be -nopad -b 65536 -fixed-time 0
Signed-off-by: Paul Spooren <mail@aparcar.org>
All callers of the rtl83xx_mc_group_* functions already do the same
check, so these aren't needed.
For rtl83xx_mc_group_alloc, this branch also incorrectly returned 0
instead of a negative value. If the branch wasn't effectively dead code
anyway, this could potentially have caused bugs, as 0 is a valid
multicast group entry index.
Fixes: cde31976e3 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The current implementation only works when store and load are called for
the same port without any other calls in between. This is because the
store function only saves a single port number instead of a portmask for
each group. It also doesn't take into account that the allocation of
multicast group entries might change between store/load calls.
As a result, the multicast port mask table gets corrupted. This also
includes the reserved entry for unknown multicast, which gets corrupted
even when no other mdb entries have been added.
Remove the code for storing/loading multicast groups entirely, as the
original commit message doesn't offer a convincing reason why this would
be necessary in the first place.
Fixes: 724e4af530 ("realtek: Store and Restore MC memberships for port enable/disable")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
There shouldn't be any reason to forward all multicast to the CPU. The
original commit message also doesn't provide a reason for this seemingly
unrelated change.
The current implementation of the delete method is also broken, as it
entirely removes any entry when the portmask contains only the CPU port,
even if it was explicitly created.
Fixes: 724e4af530 ("realtek: Store and Restore MC memberships for port enable/disable")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
There doesn't appear to be a reason to do this, as only the last entry
is actually reserved for unknown multicast.
This also fixes two issues:
- As the increment happened after the bounds check, the value of the
actually reserved last entry could be overwritten.
- On deletion of entries, a corresponding decrement was missing,
causing the wrong entry to be marked as free.
Fixes: cde31976e3 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Actually use the index returned by rtl83xx_find_l2_cam_entry.
Fixes: cde31976e3 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The port_vlan_add method may be called while a port is already a member
of that VLAN, so it needs to be able to handle changed flags. Fix it to
properly handle when the PVID or UNTAGGED flag was previously set, but
now no longer is.
To reduce duplication, move PVID configuration to a separate function.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The registers L2_PORT_STATIC_MV_ACT seem to specify the action to take
when the source address of a packet exists as a static fdb entry on
another port. By default the configured action is to drop such packets.
For standalone ports, this behaviour is undesired, as all traffic should
be forwarded to the CPU. So change the action to forward on standalone
ports.
A situation where this issue can occur is when a non-offloaded bond
interface is part of a bridge. In that case, the CPU port will have fdb
entries for devices connected to the bond interface, which are managed
by the assisted learning feature.
For now, this is only implemented for RTL838x/RTL839x, as the available
set of registers differs for the other devices.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
All ports are disabled by default, so configure the port isolation masks
and the pm field accordingly in the setup function. When port_enable is
called for a port, the isolation masks will be set up so that traffic
can flow between the port and the CPU.
While at it, change the code to also use the traffic_set method in
rtl83xx_setup, instead of writing to the RTL838x_PORT_ISO_CTRL(i)
registers directly.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Correctly update the isolation mask of the port being configured. The
port_bitmap variable should contain all other bridge members and needs
to be actually removed from the isolation mask instead of added to it.
Also actually remove the port being configured from the pm field of the
other ports, so that any other ports that are currently disabled will be
configured correctly when they are enabled.
Fixes: df8e6be59a ("rtl838x: add new architecture")
[fixed updating pm field of other ports]
Fixes: 2b88563ee5 ("realtek: update the tree to the latest refactored version")
[reintroduced incorrect pm field update]
Fixes: 27029277f9 ("realtek: add switch driver support for the RTL93XX based switches")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Add support for NXP LS1028ARDB reference board. It's a dual core
Coretex-A53 board with 4G RAM and 5 Eternet ports (4 ports are
connected to MSCC Felix switch).
The original layout of NXP board has been kept but firmware
images are adapted to be more sysupgrade friendly. At the moment
NOR and SD boots are supported.
NOR flash instructions:
* make sd card with sdboot image
* boot
* write firmware image to spi flash
$ mtd write /tmp/openwrt-layerscape-armv8_64b-fsl_ls1028a-rdb-
squashfs-firmware.bin /dev/mtd0
* change jumper to NOR boot and reset
V3:
* Added board specific network defaults for lan/wan
v2:
* Added INA220 curent monitor, PCF2129 RTC clock and NXP
SA56004ED temperature sensor to default packages
* removed compat fixups for thist board
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
The ZTE MF282 is a LTE router used (exclusively?) by the network operator
"3".
Specifications
==============
SoC: QCA9563 (775MHz)
RAM: 128MiB
Flash: 8MiB SPI-NOR + 128MiB SPI-NAND
LAN: 1x GBit LAN
LTE: ZTE MF270 (Cat4), detected as P685M
WiFi: QCA9880ac + QCA9560bgn
MAC addresses
=============
LAN: from config
WiFi 1: from config
WiFi 2: +1
Installation
============
TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:
setenv serverip 192.168.1.100
setenv ipaddr 192.168.1.1
tftpboot 0x82000000 openwrt.bin
bootm 0x82000000
From this intiramfs boot you can take a backup of the currently installed
partitions as no vendor firmware is available for download.
Once booted, transfer the sysupgrade image and run sysupgrade.
LTE Modem
=========
The LTE modem is probably the same as in the MF283+, all instructions
apply.
Configuring the connection using modemmanager works properly, the modem
provides three serial ports and a QMI CDC ethernet interface.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Rename to Fritz!Box to keep naming uniform.
Fixes: ceac4ae3b4 ("lantiq: xway: add support for AVM FRITZ!Box 7330")
Signed-off-by: Nick Hainke <vincent@systemli.org>
The current problems blocking the switch to the kernel 5.15 are
related to the GSWIP driver. This driver is only used by the
xrx200 subtarget. The other subtargets are unaffected by this
problem.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Kernel setting CONFIG_IO_URING supports high-performance I/O for file
access and servers, generally for more performant platforms, and adds
~45 KB to kernel sizes. The need for this on less "beefy" devices is
questionable, as is the size cost considering many platforms have kernel
size limits which require tricky repartitioning if outgrown. The size
cost is also large relative to the ~180 KB bump expected between major
OpenWRT kernel releases.
No OpenWrt packages have hard dependencies on this; samba4 and mariadb
can take advantage if available (+KERNEL_IO_URING:liburing) but
otherwise build and work fine.
Since CONFIG_IO_URING is already managed via the KERNEL_IO_URING setting
in Config-kernel.in (default Y), remove it from those target configs
which unconditionally enable it, and update the defaults to enable it
conditionally only on more powerful 64-bit x86 and arm devices. It may
still be manually enabled as needed for high-performance custom builds.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Since CONFIG_DYNAMIC_DEBUG is already managed via the KERNEL_DYNAMIC_DEBUG
setting in Config-kernel.in (default N), remove or disable it in target
configs which unconditionally enable it, along with the related setting
CONFIG_DYNAMIC_DEBUG_CORE. This saves several KB in the kernels for
ipq40xx, ipq806x, filogic, mt7622, qoriq, and sunxi.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This activates CONFIG_SLAB_FREELIST_RANDOM.
This option make the free list less predictable. This makes it harder to
exploit heap based security vulnerabilities.
This adds a little bit more code to the kernel and a small additional
compute overhead.
This option is activated in Debian by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The target is currently broken with Kernel 5.15 and no one in sight to
fix it. Instead of stalling the next release indefinitely, make it
source only and see if someone steps up to fix it.
Signed-off-by: Paul Spooren <paul.spooren@rhebo.com>
The target is currently broken with Kernel 5.15 and no one in sight to
fix it. Instead of stalling the next release indefinitely, make it
source only and see if someone steps up to fix it.
Signed-off-by: Paul Spooren <paul.spooren@rhebo.com>
Rename existing device to v1 and create common .dtsi
Difference to v1: 16MB Flash
Specifications:
SoC: MediaTek MT7621
RAM: 256 MB
Flash: 16 MB (SPI NOR, XM25QH128C on my device)
WiFi: MediaTek MT7915E
Switch: 1 WAN, 4 LAN (Gigabit)
Buttons: Reset, WPS
LEDs: Two Power LEDs (blue and red; together they form purple)
Power: DC 12V 1A center positive
Serial: 115200 8N1
C440 - (3V3 - GND - RX - TX) - C41 | v1 and v2
(P - G - R - T) | v2 labels them on the board
Installation:
Download and flash the manufacturer's built OpenWrt image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWrt image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings.
Recovery:
Loads only signed manufacture firmware due to bootloader RSA verification
Serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
Connect to any lan ethernet port
Power on the device while holding the reset button
Wait at least 8 seconds before releasing reset button for image to
download
MAC addresses as verified by OEM firmware:
use address source
LAN f4:a4:54:86:75:a2 label
WAN f4:a4:54:86:75:a3 label + 1
2g f4:a4:54:86:75:a2 label
5g f6:a4:54:b6:75:a2 label + LA-Bit set + 4th oktet increased
The label MAC address is found in bdinfo 0xde00.
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
The switch driver actually expects every port to have a PHY handle, and
several branches in the code determine if a port is valid by checking
for a non-zero phy field.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The RealTek 2.5G PHY providing the WAN port of the Netgear WAX206 has
previously been hard-coded in the device tree. Now that the PHY can be
probed correctly also via Clause-45 MDIO, use that instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Early versions (?) of the RTL8221B PHY cannot be identified in a regular
Clause-45 bus scan as the PHY doesn't report the implemented MMDs
correctly but returns 0 instead.
Implement custom identify function using the PKGID instead of iterating
over the implemented MMDs to work-around this problem.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This commit adds factory.bin image for TP-Link EC330-G5u v1. This allows
to install OpenWrt without connecting a serial cable (UART).
Installation using factory image
--------------------------------
Tested with "3.16.0 0.9.1 v6037.0 Build 191016 Rel.30619nb" TP-Link
firmware.
1. Login to the router web interface (http://192.168.0.1/ by default) and
save running config to "conf.bin" file
2. Open configuration file in any TP-Link config editor (e.g.
https://jahed.github.io/tp-link-config-editor/)
3. Find "DeviceInfo" section and insert a new string "<Description
val="Modem Router`telnetd -p 1023 -l login`" />" according to the
following example:
<DeviceInfo>
...
<Description val="Modem Router`telnetd -p 1023 -l login`" />
...
</DeviceInfo>
4. Save configuration file and upload changed configuration using stock
firmware interface
5. Login using telnet to IP:192.168.0.1 (Username:admin, password:1234)
6. Run "cat /proc/mtd | grep mtd7"
a. If the result is 'mtd7: 03000000 00020000 "rootfs" 03400000',
then install stock firmware using web interface to toggle booted
firmware image from "os1" to "os0"
b. If the result is 'mtd7: 03000000 00020000 "rootfs" 00400000',
then all is ok, go to the next step
7. Set up a tftp server with OpenWrt factory.bin image (IP:192.168.0.100
in this example)
8. Login using telnet to 192.168.0.1
9. Download OpenWrt factory.bin image from the tftp server:
cd /tmp
tftp -g -r factory.bin 192.168.0.100
10. Write OpenWrt factory.bin image:
dd if=/tmp/factory.bin of=/dev/mtdblock1
11. Power cycle the router
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
The TP-Link EC330-G5u v1 router has MAC address that stored in factory mtd
in ascii format. This commit makes the router use of "mac-address-ascii"
in dts.
After the change:
1. All MAC addresses are explicitly assigned in dts (the workarounds in
network scripts are no longer needed);
2. gmac0 (eth0) MAC address is no longer random.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* Delete unused lantiq makefile
* Delete redundant makefiles and unify them into the main makefile
* Refactor and unify board code into a single file
* Add support and review subtarget specific board support
Signed-off-by: Antonio Vázquez <antoniovazquezblanco@gmail.com>
This deactivates the kernel option CONFIG_OABI_COMPAT.
The old arm OABI is not needed any more, we compile all applications for
the new ARM EABI.
This reduces the attack surface of the kernel syscall interface.
On all other targets CONFIG_OABI_COMPAT is already deactivated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This deactivates the CONFIG_COMPAT kernel option.
With CONFIG_COMPAT the kernel will provide syscall interfaces for arm32
binaries in addition to the interfaces needed for arm64 binaries.
In OpenWrt the complete userspace is compiled for this specific
architecture and support for 32 bit ARM applications is not needed.
This reduces the size and the attack surface for the systems.
On all other targets CONFIG_COMPAT is already deactivated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The legacy (BSD) PTY support could open security problems in a system,
We do not need them in OpenWrt, deactivate this option in all targets.
Debian also deactivates this option.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This activates the CONFIG_ARM64_SW_TTBR0_PAN option for all arm64
kernels by default.
The CONFIG_ARM64_SW_TTBR0_PAN option prevents the kernel form accessing
user space memory directly. This makes it harder to exploit the kernel.
This is activated by default and was already activate on all other arm64
targets before.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This activates CONFIG_HARDENED_USERCOPY for the remaining targets. This
adds additional checks in the copy_from_user() and copy_to_user()
functions.
This was not activated for ARCHS38 before because of a bug in the Linux
kernel 5.4 till 5.14, which as fixed and is described here:
https://github.com/foss-for-synopsys-dwc-arc-processors/linux/issues/15
I do not know why this was deactivated for mt7629 and rockchip.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ZyXEL WSM20 aka Multy M1 is a cheap mesh router system by ZyXEL
based on the MT7621 CPU.
Specifications
==============
SoC: MediaTek MT7621AT (880MHz)
RAM: 256MiB
Flash: 128MiB NAND
Wireless: 802.11ax (2x2 MT7915E DBDC)
Ethernet: 4x 10/100/1000 (MT7530)
Button: 1x WPS, 1x Reset, 1x LED On/Off
LED: 7 LEDs (3x white, 2x red, 2x green)
MAC address assignment
======================
The MAC address assignment follows stock: The label MAC address is the LAN
MAC address, the WAN address is read from flash.
The WiFi MAC addresses are set in userspace to label MAC + 1 and label MAC
+ 2.
Installation (web interface)
============================
The device is cloud-managed, but there is a hidden local firmware upgrade
page in the OEM web interface. The device has to be registered in the
cloud in order to be able to access this page.
The system has a dual firmware design, there is no way to tell which
firmware is currently booted. Therefore, an -initramfs version is flashed
first.
1. Log into the OEM web GUI
2. Access the hidden upgrade page by navigating to
https://192.168.212.1/gui/#/main/debug/firmwareupgrade
3. Upload the -initramfs-kernel.bin file and flash it
4. Wait for OpenWrt to boot and log in via SSH
5. Transfer the sysupgrade file via SCP
6. Run sysupgrade to install the image
7. Reboot and enjoy
NB: If the initramfs version was installed in RAS2, the sysupgrade script
sets the boot number to the first partition. A backup has to be performed
manually in case the OEM firwmare should be kept.
Installation (UART method)
==========================
The UART method is more difficult, as the boot loader does not have a
timeout set. A semi-working stock firmware is required to configure it:
1. Attach UART
2. Boot the stock firmware until the message about failsafe mode appears
3. Enter failsafe mode by pressing "f" and "Enter"
4. Type "mount_root"
5. Run "fw_setenv bootmenu_delay 3"
6. Reboot, U-Boot now presents a menu
7. The -initramfs-kernel.bin image can be flashed using the menu
8. Run the regular sysupgrade for a permanent installation
Changing the partition to boot is a bit cumbersome in U-Boot, as there is
no menu to select it. It can only be checked using mstc_bootnum. To change
it, issue the following commands in U-Boot:
nand read 1800000 53c0000 800
mw.b 1800004 1 1
nand erase 53c0000 800
nand write 1800000 53c0000 800
This selects FW1. Replace "mw.b 1800004 1 1" by "mw.b 1800004 2 1" to
change to the second slot.
Back to stock
=============
It is possible to flash back to stock, but a OEM firmware upgrade is
required. ZyXEL does not provide the link on its website, but the link
can be acquired from the OEM web GUI by analyzing the transferred JSON
objects.
It is then a matter of writing the firmware to Kernel2 and setting the
boot partition to FW2:
mtd write zyxel.bin Kernel2
echo -ne "\x02" | dd of=/dev/mtdblock7 count=1 bs=1 seek=4 conv=notrunc
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Credits to forum users Annick and SirLouen for their initial work on this
device
This activates the CONFIG_SCHED_STACK_END_CHECK option.
The kernel will check if the kernel stack overflowed in the schedule()
function. This just adds a very small computational overhead.
This option is activated in Debian by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This activates some extra checks in SLAB or SLUB to make it harder to
execute kernel heap exploits. This adds a minor performance
degradation which I haven't measured-.
Many mainstream Linux distributions also activate this option.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This activates the following kernel options by default:
* CONFIG_RANDOM_TRUST_CPU
* CONFIG_RANDOM_TRUST_BOOTLOADER
With these option Linux will also use data from the CPU RNG e.g. RDRAND
and the bootloader to initialize the Linux RNG if such sources are
available.
These random bits are used in addition to the other sources, no other
sources are getting deactivated. I read that the Chacha mixer isn't
vulnerable to injected entropy, so this should not be a problem even if
these sources might inject bad random data.
The Linux kernel suggests to activate both options, Debian also
activates them. This does not increase kernel code size.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It was brought to attention the Archer AX23 v1 fails to read jffs2 data
from time to time. While this is not reproducible on my unit, it is on
others.
Reducing the SPI frequency does the trick. While it worked with at lest
40 MHz, opt for the cautious side and choose a save frequency of 25 MHz.
Apply the same treatment to the Mercusys MR70X which uses a similar
design just in case.
Signed-off-by: David Bauer <mail@david-bauer.net>
OpenWrt's developer guide prefers having actual patches so they an be
sent upstream more easily.
However, in the case of hack-5.15 patches which are not meant for
upstream, adding proper fields allows for `git am` to properly function.
This commit tries to rectify that, by digging in the history to find
where and how it was first added.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
- irq_domain_add_simple() can't be used on bmips since interrupts aren't
hardcoded with specific offsets for internal and external as opposed to
bcm63xx. This is needed to avoid collisions with other interrupts.
- remove unused bcm63xx-specific code.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
There's no need to poll the gpio keys every 20 ms and the linux kernel
documentation suggests 100 ms.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The current bcma SPROM extraction from upstream only supports SPROMs with
revisions from 8 to 11.
Let's align the downstream fallback driver with upstream.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
- Remove unneeded mac bytes from struct (it's already present in the SPROM).
- Convert devid_override to boolean.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
- Remove unneeded mac bytes from struct (it's already present in the SPROM).
- Convert devid_override to boolean.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Convert GL-AP1300 to DSA and enable it.
While working on it rename the GL-AP1300 leds from green to white.
Tested-by: Rob White <rob@blue-wave.net>
Tested-by: Robert Sommer <frauhottelmann@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
As was done in commit e11d00d44c ("ath79: create Aruba AP-105 APBoot
compatible image"), alter the Aruba AP-175 image generation process so
OpenWrt can be loaded with the vendor Aruba APBoot. Since the
remainder of the explanation and installation process is identical,
continuing the quote from that commit:
This works by prepending the OpenWrt LZMA loader to the uImage and
jumping directly to the loader. Aruba does not offer bootm on these
boards.
This approach keeps compatibility to devices which had their U-Boot
replaced. Both bootloaders can boot the same image.
With this patch, new installations do not require replacing the
bootloader and can be performed from the serial console without
opening the case.
Installation
------------
1. Attach to the serial console of the AP-175.
Interrupt autoboot and change the U-Boot env.
$ setenv apb_rb_openwrt "setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66;
netget 0x84000000 ap175.bin; go 0x84000040"
$ setenv apb_fb_openwrt "cp.b 0xbf040000 0x84000000 0x10000;
go 0x84000040"
$ setenv bootcmd "run apb_fb_openwrt"
$ saveenv
2. Load the OpenWrt initramfs image on the device using TFTP.
Place the initramfs image as "ap175.bin" in the TFTP server
root directory, connect it to the AP and make the server reachable
at 192.168.1.66/24.
$ run apb_rb_openwrt
3. Once OpenWrt booted, transfer the sysupgrade image to the device
using scp and use sysupgrade to install the firmware.
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
The previous attempt to replace an open coded paged read in the RealTek
Ethernet PHY driver was too naive and resulted in breaking the r8169
PCIe Ethernet driver which also makes use of the RealTek Ethernet PHY
driver.
Fix this by instead of using the (not yet populated) paged operations
rather use rtl821x_write_page and protect the whole paged read operation
using the MDIO bus mutex.
Fixes: 998b973157 ("kernel: net: phy: realtek: improve RealTek 2.5G PHY driver")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It was found this device uses a single tri-color power/status LED
rather than individual red/orange LEDs, which also supports green.
Add GPIO for green color and use with `boot` and `running` aliases.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
- Correct WiFi MACs, they didn't match oem firmware
- Move nvmem-cells to bdinfo partition and remove &bdinfo reference
- Add OEM device model name R13 to SUPPORTED_DEVICES
This allows sysupgrading from Cudy's OpenWrt fork without force
- Label red_led and use it during failsafe mode and upgrades
MAC addresses as verified by OEM firmware:
use address source
LAN b4:4b:d6:2d:c8:4a label
WAN b4:4b:d6:2d:c8:4b label + 1
2g b4:4b:d6:2d:c8:4a label
5g b6:4b:d6:3d:c8:4a label + LA-Bit set + 4th oktet increased
The label MAC address is found in bdinfo 0xde00.
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
[read wifi mac from flash offset]
Signed-off-by: David Bauer <mail@david-bauer.net>
The Alcatel HH40V is a CAT4 LTE router used by various ISPs.
Specifications
==============
SoC: QCA9531 650MHz
RAM: 128MiB
Flash: 32MiB SPI NOR
LAN: 1x 10/100MBit
WAN: 1x 10/100MBit
LTE: MDM9607 USB 2.0 (rndis configuration)
WiFi: 802.11n (SoC integrated)
MAC address assignment
======================
There are three MAC addresses stored in the flash ROM, the assignment
follows stock. The MAC on the label is the WiFi MAC address.
Installation (TFTP)
===================
1. Connect serial console
2. Configure static IP to 192.168.1.112
3. Put OpenWrt factory.bin file as firmware-system.bin
4. Press Power + WPS and plug in power
5. Keep buttons pressed until TFTP requests are visible
6. Wait for the system to finish flashing and wait for reboot
7. Bootup will fail as the kernel offset is wrong
8. Run "setenv bootcmd bootm 0x9f150000"
9. Reset board and enjoy OpenWrt
Installation (without UART)
===========================
Installation without UART is a bit tricky and requires several steps too
long for the commit message. Basic steps:
1. Create configure backup
2. Patch backup file to enable SSH
3. Login via SSH and configure the new bootcmd
3. Flash OpenWrt factory.bin image manually (sysupgrade doesn't work)
More detailed instructions will be provided on the Wiki page.
Tested by: Christian Heuff <christian@heuff.at>
Signed-off-by: Andreas Böhler <dev@aboehler.at>
The RTL8366S/RB switch node in DTS defines "mii-bus = <&mdio0>" to permit
management via SMI but this has likely never worked, instead falling back
to using GPIOs in the past:
rtl8366s switch: cannot find mdio bus from bus handle (yet)
rtl8366s switch: using GPIO pins 19 (SDA) and 20 (SCK)
rtl8366s switch: RTL8366 ver. 1 chip found
Recently, the rtl8366s and rtl8366_smi drivers were changed from built-in
to loadable modules. This affected driver probing order and caused switch
initialization (and network access) to fail:
rtl8366s switch: using MDIO bus 'ag71xx_mdio'
rtl8366s switch: unknown chip id (ffff)
rtl8366s switch: chip detection failed, err=-19
Force using GPIOs to manage the switch by dropping the "mii-bus" DTS
definition, which works for both built-in and loadable switch drivers.
Fixes: 6e0f0eae5b ("ath79: use rtl8366s and rtl8366_smi as a module")
Fixes: 575ec7a4b1 ("ath79: use rtl8366rb as a module")
Tested-by: Tony Ambardar <itugrok@yahoo.com> # WZR-HP-G300NH (RTL8366S)
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Switch drivers for RTL8366S/RB were packaged as modules but not properly
added to device definitions for WZR-HP-G300NH router variants, breaking
network access to both after installation or upgrade.
Assign the correct switch driver package for each router.
Fixes: 6e0f0eae5b ("ath79: use rtl8366s and rtl8366_smi as a module")
Fixes: 575ec7a4b1 ("ath79: use rtl8366rb as a module")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.
Fixes: #11919
Signed-off-by: Haoan Li <lihaoan1001@163.com>
Apart from the embedded BCM63268 wireless, this device has an external BCM4360
connected by PCIe which needs a fallback SPROM.
b43 isn't enabled for this device because BCM4360 isn't supported (AC PHY).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Apart from the embedded BCM6362 wireless, Netgear DGND3700v2 has external
BCM43228 wireless connected by PCIe.
Fallback SPROM isn't needed for this one because it has a physical SPROM.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
late_initcall_sync() is no longer needed so standard module functions can be
used on all bmips PCI/PCIe drivers.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Stop using bmips b43-sprom fixups and switch to generic bcma/ssb fallback
SPROMs. This way we don't need to include the b43-sprom fixups on devices
without Broadcom wireless.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This adds generic kernel support for Broadcom Fallback SPROMs so that it can be
used in any target, even non Broadcom ones.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
A patch was added in kernel 5.4 to support the fiber operation of
AR8033 with ramips devices. In kernel 5.18 similar enhancements
were added to the kernel. Those patches are required for other
fiber based devices but when added, build fails for ramips targets.
This commit removes the ramips patch and adds the kernel 5.18 ones.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
[ split commit,refresh patch and improve commit message ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
A patch was added in kernel 5.4 to support the fiber operation of
AR8033 with ramips devices. In kernel 5.18 similar enhancements
were added to the kernel. Those patches are required for other
fiber based devices but when added, build fails for ramips targets.
This commit removes the ramips patch and adds the kernel 5.18 ones.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
[ split commit, refresh patch and improve commit title ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace pending 730-net-phy-at803x-fix-feature-detection.patch with
upstream version and move it to backport.
Refresh other related patch while moving it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The patch needs to be refreshed to apply cleanly.
Fixes: 998b973157 ("kernel: net: phy: realtek: improve RealTek 2.5G PHY driver")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: ESMT M15T4G16256A 512MB
Ethernet (Max Speed):
XDR4288: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan
XDR6086: 1x 2.5G Wan, 1x 2.5G Lan, 1x 1G Lan
XDR6088: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan
WiFi:
XDR4288: MT7976DAN (2.4G 2T2R, 5G 3T3R)
XDR6086/XDR6088:
WiFi1: MT7976GN 2.4GHz 4T4R
WiFi2: MT7976AN 5GHz 4T4R
Button: Reset, WPS, Turbo
USB: 1 x USB 3.0
Power: DC 12V 4A
Flash instructions:
1. Execute the following operation to open nc shell:
https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting
2. Replace the stock bootloader to OpenWrt's:
dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin
dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip
3. Connect to your PC via the Gigabit port of the router,
set a static ip on the ethernet interface of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
4. Download the initramfs image, and restart the router,
waiting for tftp recovery to complete.
5. After openwrt boots up, perform sysupgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
[Add uboot build, fit and sysupgrade support, fix RealTek PHYs]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* use interface mode switching only when operating in C45 mode
Linux prevents switching the interface mode when using C22 MDIO,
hence use rate-adapter mode in case the PHY controlled via C22.
* use phy_read_paged where appropriate
* use existing generic inline functions to handle 10GbE advertisements
instead of redundantly defining register macros in realtek.c which
are not actually vendor-specific.
* make sure 10GbE advertisement is valid, preventing false-positive
warning "Downshift occurred from negotiated speed 2.5Gbps to actual
speed 1Gbps, check cabling!" with some link-partners using 1G mode.
* Support Link Down Power Saving Mode (ALDPS)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of use mac-address-ascii in nvmem_get_mac_address
function, move it into of_get_mac_addr_nvmem function to
support more devices.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
The Config partition of some machines is special, and the openwrt script
cannot read the protest_lan_mac correctly. This problem can be solved by
reading the mac address (ascii) in dts.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Fix the network configuration according to the device tree.
Fixes: 5faff99 ("mediatek: filogic: fix mt7986a ethernet devicetree entries")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
According to SinoVoip up to 3A @ 3.3V are available for both
SFP modules together. Raise energy limit from 1W (default) to 3W,
however, be aware that using modules consuming more than 1W will
require active cooling!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of erasing the entire NAND partition holding the kernel during
every system upgrade and then flashing a Yaffs file system image
prepared using kernel2minor (not accounting for bad blocks in the
process), use the Yafut utility to replace the kernel executable on
MikroTik NAND devices, preserving the existing Yaffs file system
(including bad block information) on the partition holding the kernel.
Add Yafut to DEFAULT_PACKAGES for the ath79/mikrotik target, so that the
tool is included in the initramfs images created when building for
multiple profiles. However, exclude Yafut from the images built for
MikroTik devices with NOR flash as the tool is currently only meant to
be used on devices with NAND flash.
As this addresses the concerns for MikroTik NAND devices discussed in
commit 9d96b6fb72 ("ath79/mikrotik: disable building NAND images"),
re-enable building images for these devices.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
MEMREAD is a new ioctl for MTD character devices that was first included
in Linux 6.1. It allows userspace applications to use the Linux
kernel's OOB autoplacement mechanism while reading data from NAND
devices. The Yafut tool needs this ioctl to do its job.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
The ramdisk used by sysupgrade on MikroTik devices currently includes
U-Boot fw_* files that are not necessary for performing a system upgrade
on that platform. The relevant lines were added to
target/linux/ath79/mikrotik/base-files/lib/upgrade/platform.sh by commit
a66eee6336 ("ath79: add mikrotik subtarget"), likely because they also
existed in target/linux/ath79/nand/base-files/lib/upgrade/platform.sh,
where the platform_do_upgrade_mikrotik_nand() function moved by commit
a66eee6336 originally lived. However, these lines were added to
target/linux/ath79/nand/base-files/lib/upgrade/platform.sh by commit
55e6c903ae ("ath79: GL-AR300M: provide NAND support; increase to 4 MB
kernel"), which is not related to MikroTik devices in any way.
Remove the code adding unused U-Boot fw_* files to the ramdisk used by
sysupgrade on MikroTik devices.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
Alter the Aruba AP-105 image generation process so OpenWrt can be loaded
with the vendor Aruba APBoot.
This works by prepending the OpenWrt LZMA loader to the uImage and
jumping directly to the loader. Aruba does not offer bootm on these
boards.
This approach keeps compatibility to devices which had their U-Boot
replaced. Both bootloaders can boot the same image.
The same modification is most likely also possible for the Aruba AP-175.
With this patch, new installations do not require replacing the
bootloader and can be performed from the serial console without opening
the case.
Installation
------------
1. Attach to the serial console of the AP-105.
Interrupt autoboot and change the U-Boot env.
$ setenv apb_rb_openwrt "setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66;
netget 0x84000000 ap105.bin; go 0x84000040"
$ setenv apb_fb_openwrt "cp.b 0xbf040000 0x84000000 0x10000;
go 0x84000040"
$ setenv bootcmd "run apb_fb_openwrt"
$ saveenv
2. Load the OpenWrt initramfs image on the device using TFTP.
Place the initramfs image as "ap105.bin" in the TFTP server
root directory, connect it to the AP and make the server reachable
at 192.168.1.66/24.
$ run apb_rb_openwrt
3. Once OpenWrt booted, transfer the sysupgrade image to the device
using scp and use sysupgrade to install the firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
In addition to standardizing LED names to match the rest of the systems, this
commit fixes a possibly erroneous pinout for LEDs in Comfast CF-E314N v2.
In particular, rssimediumhigh and rssihigh are moved from pins 13 and 14 to
14 and 16 respectively. In addition to working on a test device, this pinout
better matches the one set out in the prototype support patch for the device
in Github PR #1873.
Signed-off-by: Mark Onstid <turretkeeper@mail.com>
RA75 has 5 physical LEDs under 2 indicators, mixed with light pipes:
Indicator "System":
GPIO0: blue
GPIO2: amber
Indicator "Signal":
GPIO44: blue
GPIO37: amber
GPIO46: red
All except GPIO46 were already added by Jo Deisenhofer. GPIO46 is used for UART1 by
default, so it needs additional pin control change in devicetree to be operational.
Verified on my RA75.
Signed-off-by: Oleksandr Zharov <alex.zeed@gmail.com>
Re-enable the Aruba AP-365 with DSA support. Changes are trvivial, as
the board design is pretty much the already updated AP-303.
Run-tested on the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Import commit "ubi: Fix failure attaching when vid_hdr offset equals to
(sub)page size" which did not yet make it to stable upstream Linux trees.
Fixes: #12232Fixes: #12339
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that new pinconf features have been backported sync pinctrl-mt7981
and pinctrl-m7986 with bleeding-edge upstream versions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport new features for MediaTek pinctrl/pinconf drivers from upstream.
This will serve as the base to improve pinconf bias/pull-up/pull-down on
MT7981 and MT7986, and also prepare for upcoming support for MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Avoid MCU getting "command reply receive timed out" message when LED
configuration setting trigger function is enabled in heartbeat mode.
Signed-off-by: Ian Chang <ianchang@ieiworld.com>
It appears that the refactor of the upgrade process for NAND devices resulted in the nand_do_upgrade_success step not being called for
devices using the linksys.sh script. As a result, configuration was
not preserved over sysupgrade steps.
This corrects a typo in the call of nand_do_upgrade_failed for ipq40xx
and ipq806x devices using the linksys.sh script.
Fixes: 8634c1080d ("ipq40xx: Fix Linksys upgrade, restore config step")
Fixes: 2715aff5df ("ipq806x: Fix Linksys upgrade, restore config step")
Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
It appears that the refactor of the upgrade process for NAND devices resulted in the nand_do_upgrade_success step not being called for
devices using the linksys.sh script. As a result, configuration was
not preserved over sysupgrade steps.
This restores the preservation of configs for mvebu/cortexa9 devices using the
linksys.sh script.
Fixes: e25e6d8e54 ("base-files: fix and clean up nand sysupgrade code")
Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
It appears that the refactor of the upgrade process for NAND devices
resulted in the nand_do_upgrade_success step not being called for
devices using the linksys.sh script. As a result, configuration was
not preserved over sysupgrade steps.
This restores the preservation of configs for kirkwood devices using the
linksys.sh script.
Fixes: e25e6d8e54 ("base-files: fix and clean up nand sysupgrade code")
Fixes: #12298
Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
Getting ready for the next release.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[rmilecki: tested on GT-AC5300: boot, sysupgrade & 940 Mbps NAT]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
bmips target is now more stable and it's time to start generating buildbot
images in order to receive a wider testing, which will be essential to replace
bcm63xx target in the future.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
BMIPS is a generic arch that can be used for multiple Broadcom SoCs, each one
with its own specific drivers, so instead of having a huge kernel supporting
all of them, let's switch to a subtarget per SoC like other OpenWrt targets.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add BCM6328 and BCM6358 LED kernel modules.
This allows selecting the LED controllers only for those devices using them.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Sercomm SHG2500 is a BCM63168 with 128M of RAM, 256M of NAND, an external
BCM53124S switch for the LAN ports and internal/external Broadcom wifi.
LEDs are connected to an external MSP430G2513 MCU controlled via SPI.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Make use of sercomm-pid script for generating the Sercomm PID, which avoids
having to add an array of hex bytes for every new Sercomm device.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SERCOMM_VERSION is ambiguous and it should be more clear that it refers to the
version used for the filesystem.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
