Was inadvertantly missed from the inital forward port from ar71xx to
ath79.
Fixes: 1588114cf2 ("ath79: add etactica-eg200 support")
Signed-off-by: Karl Palsson <karlp@etactica.com>
[commit description/subject facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In the rare event a pre-populated fw_env.config exists in the rootfs prior
to firstboot, calling fw_setenv after the system has initialised will
annihilate the devices environment due to two identical lines in
fw_env.config.
Check for existence prior to blind appendage.
Signed-off-by: Imran Khan <gururug@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: fixed patch format, improved grep, cosmetics]
Hardware:
Allwinner H3 upto 1.2GHz
512MB DDR3 RAM
8GB on-board eMMC - mountable, can be used as boot with custom boot.scr
microSD-card slot
WiFi 802.11n (AP6212A) - working
Bluetooth (AP6212A) - not working for now
Micro-USB OTG + 2*USB headers
UART 3.3V - working
GPIO/I2C/SPI 2.54mm headers
Standard sunxi SD-card installation procedure - copy image to SD card,
insert in into slot and boot. First time you will need UART adapter to
enable on-board wireless (or just build custom image with enabled WiFi).
To boot from eMMC:
- boot from SD
- copy SD image to emmc (dd bs=... if=.... of=/dev/mmcblk2)
- mount eMMC boot partition and replace boot script on it
- unmount, reboot
To use i2c, spi and more uarts - replace dtb on boot partition with
fixed one (use dtc or fdt-tools).
Signed-off-by: Roman Bazalevsky <rvb@rvb.name>
[rebase onto device name consolidation patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This changes device definition to resemble the vendor_device scheme
already present for the majority of device compatible strings.
By doing this, we achieve several advantages at once:
- Image names and node names are more consistent with other targets.
- SUPPORTED_DEVICES can be set automatically for all but two cases.
- Image names and node names are in line with DEVICE_TITLEs.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* add u-boot support for uDPU
* add line to copy u-boot binary to STAGING_DIR_IMAGE, this can later be used
as BL33 variable required for ATF build
* add patch to increase max gunzip size in mvebu_armada-37xx.h which is
required for booting the itb recovery images
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
ATF mvebu is required for building a functional bootloader for A7K/A8K and
A37xx platforms. uDPU device is added as the first target.
A3700 platform has a wide range of settings which can be used per device, so
options are defined under the Device sections.
Platform also required WTP (recovery) tools and mv-ddr package for the DDR
topology configuration. 32-bit cross compiler is used for building the WTMI
image.
After the build, flash-image.bin can be used with the bubt command from the
u-boot shell to flash the new version of u-boot.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
All patches have been dropped, they're either redundant (e.g. due to the
new and unset CONFIG_SPL_FAT_WRITE), break compilation (thumb hacks) or
have been applied upstream.
The defconfig for am335x_boneblack has been removed upstream [0], so use
am335x_evm for boneblack too.
Size changes (before, after, file):
ti_am335x-evm and ti_am335x-bone-black:
79804 110832 MLO
623836 756148 u-boot.img
ti_omap3-beagle:
54148 57708 MLO
496272 665728 u-boot.img
ti_omap4-panda:
39356 40204 MLO
284648 366672 u-boot.img
Tested on boneblack, which has the biggest spl size increase. The beagle and
panda spl sizes seem reasonable to not break booting.
[0] 8fa7f65dd0
Signed-off-by: Andre Heider <a.heider@gmail.com>
The GL.iNet GL-AR750S has been supported by the ar71xx and ath79
platforms with access to its 16 MB NOR flash, but not its 128 MB
SPI NAND flash.
This commit provides support for the NAND through the upstream
SPI-NAND framework.
At this time, the OEM U-Boot appears to only support loading the
kernel from NOR. This configuration is preserved as this time,
with the glinet,gl-ar750s-nand name reserved for a potential,
future, NAND-only boot.
The family of GL-AR750S devices on the ath79 platform now includes:
* glinet,gl-ar750m-nor-nand "nand" target
* glinet,gl-ar750m-nor "nand" target (NAND-aware)
NB: This commit increases the kernel size from 2 MB to 4 MB
"Force-less" sysupgrade is presently supported from the current
versions of following NOR-based firmwre images to the version of
glinet,gl-ar750s-nor firmware produced by this commit:
* glinet,gl-ar750s -- OpenWrt 19.07 ar71xx
* glinet,gl-ar750s -- OpenWrt 19.07 ath79
Users who have sucessfully upgraded to glinet,gl-ar750m-nor may then
flash glinet,gl-ar750m-nor-nand with sysupgrade to transtion to the
NAND-based variant.
Other upgrades to these images, including directly to the NAND-based
glinet,gl-ar750s-nor-nand firmware, can be accomplished through U-Boot.
NB: See "ath79: restrict GL-AR750S kernel build-size to 2 MB" which
enables flashing of NAND factory.img with the current GL-iNet U-Boot,
"U-Boot 1.1.4-gcf378d80-dirty (Aug 16 2018 - 07:51:15)"
The GL-AR750S OEM U-Boot allows upload and flashing of either NOR
firmware (sysupgrade.bin) or NAND firmware (factory.img) through its
HTTP-based GUI. Serial connectivity is not required.
The glinet,gl-ar750s-nor and glinet,gl-ar750s-nor-nand images
generated after this commit flash each other directly.
This commit changes the control of the USB VBUS to gpio-hog from
regulator-fixed introduced by commit 0f6b944c92. This reduces the
compressed kernel size by ~14 kB, with no apparent loss of
functionality. No other ath79-nand boards are using regulator-fixed
at this time.
Note: mtd_get_mac_binary art 0x5006 does not return the proper MAC
and the GL.iNet source indicates that only the 0x0 offset is valid
The ar71xx targets are unmodified.
Cc: Alexander Wördekemper <alexwoerde@web.de>
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
The GL.iNet GL-AR300M series of devices includes variants without NAND
and only the 16 MB NOR flash. These include the GL-AR300M16 and the
GL-AR300M-Lite (already with its own board name).
This board-name addition provides disambiguation from the NAND-bearing
GL-AR300M devices, both for OpenWrt code and for end users.
Kernel and firmware support for NAND and UBI will add ~320 kB to the
overall firmware size at this time. This NOR-only option continues to
provide more compact firmware for both the GL-AR300M16 as well as
those who wish to use it as an alternate or primary, NOR-resident
firmware on the GL-AR300M.
The ar71xx targets are unmodified.
Installation
------------
Install through OEM U-Boot (HTTP-based) or `sysupgrade --force` when
booted from NOR and running OEM or OpenWrt, NOR-based firmware.
As one of the intentions is disambiguation from NAND-bearing units,
users who have flashed this firmware onto a device with NAND would
need to use U-Boot or `sysupgrade --force` to flash firmware that
again supports NAND.
There are no additional SUPPORTED_DEVICES as it is not possible to
determine if a device does or does not have NAND based on
either the OEM's or OpenWrt's board names prior to this patch.
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Forward the OpenWrt TARGET_LDFLAGS to the linker of the fw_printenv tool.
In addition also use the more standard make invocation script.
With this change the fw_printenv tool is built with PIE and Full RELRO
support when activated globally in OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Also update the U-Boot BSP patch for I2SE Duckbill devices.
Run tested on I2SE Duckbill and Olimex OLinuXino Maxi boards.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
This patch adds ath79 support for Netgear WNR2200.
Router was previously supported by ar71xx target only (8 MiB variant).
Netgear WNR2200 has two flash versions - 8MiB sold in EU, US etc. and
16 MiB for Russia and China markets. Apart from flash size both variants
share the same hardware specification.
Specification
=============
* Description: Netgear WNR2200
* Loader: U-boot
* SOC: Atheros AR7241 (360 MHz)
* RAM: 64 MiB
* Flash: 8 MiB or 16 MiB (SPI NOR)
- U-boot binary: 256 KiB
- U-boot environment: 64 KiB
- Firmware: 7808 KiB or 16000 KiB
- ART: 64 KiB
* Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN
* Wireless: 2.4 GHz b/g/n (Atheros AR9287)
* USB: yes, 1 x USB 2.0
* Buttons:
- Reset
- WiFi (rfkill)
- WPS
* LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN (blue)
- 4 x LAN (amber/green)
- WPS (green)
* UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
* Power supply: DC 12V 1.5A
* MAC addresses: LAN on case label, WAN +1, WLAN +2
Installation
============
* TFTP recovery
* TFTP via U-boot prompt
* sysupgrade
* Web interface
Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_generic=y
CONFIG_TARGET_ath79_generic_DEVICE_netgear_wnr2200-8m=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
CONFIG_KERNEL_DEBUG_INFO=y
CONFIG_KERNEL_DEBUG_KERNEL=y
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Hardware
--------
SoC: Qualcomm IPQ4019
RAM: 256M DDR3
FLASH: 128M NAND
WiFi: 2T2R IPQ4019 bgn
2T2R IPQ4019 a/n/ac
ETH: Atheros AR8033 RGMII PHY
BTN: 1x Connect (WPS)
LED: Power (green/red/yellow)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz1200'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz1200.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ1200.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz1200.bin uboot0
> mtd write /path/to/uboot-fritz1200.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
f92be9d add support for AVM FRITZ!Repeater 1200
d651302 enable support for Atheros AR8033 PHY
e4c857c add machtype override hack
Signed-off-by: David Bauer <mail@david-bauer.net>
Erasesize doesn't belong in the u-boot env config for block devices as it is
known to be 512 byte aligned.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
572ff7f fritzcreator: actually add checksum spacer
6edce1a fritzcreator: replace obscure padding generation with something more portable
2ff189f add ASUS RT-AC58U "easy install" factory u-boot shim
b91f9c2 readd spi-nand support
486ae53 improve cmd_sysupgrade
b0933f1 replace sstrip with strip
882e48a do not include generated files into git
0c5aa5f fix bugs in ipq40xx_cdp.c
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds sysupgrade, uboot-env and networking support
for Methode uDPU device.
Device features 4 partitions:
-----------------------------------------
| boot | recovery | rootfs | misc |
| (ext4) | (ext4) | (fsf2) | (f2fs) |
_________________________________________
Idea was to use f2fs only but the u-boot currently lacks support
so first 2 partition are ext4 to be u-boot readable, and this was
a reason why custom build and sysupgrade sections were required.
On the sysupgrade, boot and rootfs partitions are updated, firmare
image and user configuration is saved on the misc partition and if
the upgrade was successfull, recovery partition will be updated on
after the reboot from preinit script. If the sysupgrade fails for any
reason, device will fallback to recovery initramfs image.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
This changes the default PKG_BUILD_DIR to take BUILD_VARIANT into
account (if set), so that packages do not need to manually override
PKG_BUILD_DIR just to handle variants.
This also updates most base packages with variants to use the updated
default PKG_BUILD_DIR.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
- make create_pbl and byte_swap as host tools
- fix a bug that maybe use the cross compiler
to compile create_pbl and byte_swap:
# -a option appends the image for Chassis 3 devices in case of non secure boot
aarch64-openwrt-linux-musl-gcc -Wall -Werror -pedantic -std=c99 -O2
-DVERSION=v1.5(release):reboot-10604-ge9216b3336 -D_GNU_SOURCE -D_XOPEN_SOURCE=700
-c -o create_pbl.o create_pbl.c
cc1: note: someone does not honour COPTS correctly, passed 0 times
LD create_pbl
/usr/bin/ld: create_pbl.o: Relocations in generic ELF (EM: 183)
/usr/bin/ld: create_pbl.o: Relocations in generic ELF (EM: 183)
/usr/bin/ld: create_pbl.o: Relocations in generic ELF (EM: 183)
create_pbl.o: error adding symbols: File in wrong format
collect2: error: ld returned 1 exit status
Makefile:43: recipe for target create_pbl failed
make[4]: *** [create_pbl] Error 1
plat/nxp/tools/pbl_ch2.mk:45: recipe for target pbl failed
make[3]: *** [pbl] Error 2
- add tfa- prefix to all tools in order to avoid future clashes with
other toolnames
Signed-off-by: Biwen Li <biwen.li@nxp.com>
[added missing HOST_CFLAGS, added tfa- prefix to the tools]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
fiptool is a host tool, used in a firmware generation pipeline, but it's
not treated as such, leading to the build breakage on the hosts which
don't have {Open,Libre}SSL dev package installed:
In file included from fiptool.h:16:0,
from fiptool.c:19:
fiptool_platform.h:18:27: fatal error: openssl/sha.h:
No such file or directory
# include <openssl/sha.h>
So this patch promotes fiptool into the host tool with proper host
include and library paths under STAGING_DIR.
Ref: https://github.com/openwrt/openwrt/pull/2267
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Specifications:
- SoC: AR9344
- RAM: 128MB
- Flash: 2 * 16MB (MX25L12845)
- Ethernet: 2 * FE LAN & 1 * FE WAN
- WiFi: 2.4G: AR9344 5G: QCA9882
Flash instruction:
1. Hold reset and power up the router
2. Set your IP to 192.168.1.x
3. Open 192.168.1.1 and upload the generated *factory* firmware
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Some devices and packages require newer version of u-boot to work
properly, update u-boot to keep up with 4.19 kernel.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
[re-added missing commit message]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch is in a series to allow additional STOP indexes after umount,
so that other block devices may stop cleanly.
kdumpinit is now STOP=90
Signed-off-by: Joseph Tingiris <joseph.tingiris@gmail.com>
After commit e82a4d9cfb ("config: regenerate *_shipped sources") the mconf
parser became more strict as a side effect and started to spew a series of
warnings when evaluating our generated kconfig sources:
tmp/.config-package.in:705:warning: ignoring unsupported character '@'
The root cause of these warnings is a wrong use of the @SYMBOL dependency
syntax in various Makefile. Fix the corresponding Makefiles by turning
`@SYM||@SYM2` expressions into the proper `@(SYM||SYM2)` form.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When targets for multiple ESPRESSObin devices were added, not all
files were updated which means any ESPRESSObin version beside generic
won't have proper networking, sysupgrade and uboot-env. This patch
fixes the issue.
* fixup network detection
* fixup uboot-env
* fixup platform.sh for sysupgrade
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Current latest LSDK-19.03 u-boot had a bug that bootcmd
environment was always been reset when u-boot started up.
This was found on boards with spi NOR boot. Before the
proper fix-up is applied, we have to use a workaround
to hard code the bootcmd for OpenWrt booting for now.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to convert to use TF-A for firmware.
- Use un-swapped rcw since swapping will be done in TF-A.
- Use u-boot with TF-A defconfig.
- Rework memory map for TF-A introduction.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Add TF-A packages for Layerscape to implement trusted firmware.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Instead of maintaining 3 very similar subtargets merge them into one.
This does not use the Arm NEON extension any more, because the SAMA5D3
does not support NEON.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
This adds the host staging directory to the include path to make it use
the zlib.h files from the staging include directory and also link
against the zlib version from the staging directory.
This fixes a compile problem when the zlib header were not installed on
the build host.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[picked from openwrt-18.06]
Specification:
- Qualcomm Atheros SoC QCA9558
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 1x 10/100/1000 Mbps Ethernet
- 3T3R 2.4 GHz (QCA9558 WMAC)
- 3T3R 5.8 Ghz (QCA9880-BR4A, Senao PCE4553AH)
https://fccid.io/A8J-ECB1750
Tested and working:
- lan, wireless, leds, sysupgrade (tftp)
Flash instructions:
1.) tftp recovery
- use a 1GbE switch or direct attached 1GbE link
- setup client ip address 192.168.1.10 and start tftpd
- save "openwrt-ath79-generic-engenius_ecb1750-initramfs-kernel.bin" as "ap.bin" in tfpd root directory
- plugin powercord and hold reset button 10secs.. "ap.bin" will be downloaded and executed
- afterwards login via ssh and do a sysuprade
2.) oem webinterface factory install (not tested)
Use normal webinterface upgrade page und select "openwrt-ath79-generic-engenius_ecb1750-squashfs-factory.bin".
3.) oem webinterface command injection
OEM Firmware already running OpenWrt (Attitude Adjustment 12.09).
Use OEM webinterface and command injection. See wiki for details.
https://openwrt.org/toh/engenius/engenius_ecb1750_1
Signed-off-by: sven friedmann <sf.openwrt@okay.ms>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[use interrupt-driven "gpio-keys" binding]
The Linksys EA8300 is based on QCA4019 and QCA9888 and provides three,
independent radios. NAND provides two, alternate kernel/firmware
images with fail-over provided by the OEM U-Boot.
Installation:
"Factory" images may be installed directly through the OEM GUI.
Hardware Highlights:
* IPQ4019 at 717 MHz (4 CPUs)
* 256 MB NAND (Winbond W29N02GV, 8-bit parallel)
* 256 MB RAM
* Three, fully-functional radios; `iw phy` reports (FCC/US, -CT):
* 2.4 GHz radio at 30 dBm
* 5 GHz radio on ch. 36-64 at 23 dBm
* 5 GHz radio on ch. 100-144 at 23 dBm (DFS), 149-165 at 30 dBm
#{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1
* All two-stream, MCS 0-9
* 4x GigE LAN, 1x GigE Internet Ethernet jacks with port lights
* USB3, single port on rear with LED
* WPS and reset buttons
* Four status lights on top
* Serial pads internal (unpopulated)
"Linksys Dallas WiFi AP router based on Qualcomm AP DK07.1-c1"
Implementation Notes:
The OEM flash layout is preserved at this time with 3 MB kernel and
~69 MB UBIFS for each firmware version. The sysdiag (1 MB) and
syscfg (56 MB) partitions are untouched, available as read-only.
Serial Connectivity:
Serial connectivity is *not* required to flash.
Serial may be accessed by opening the device and connecting
a 3.3-V adapter using 115200, 8n1. U-Boot access is good,
including the ability to load images over TFTP and
either run or flash them.
Looking at the top of the board, from the front of the unit,
J3 can be found on the right edge of the board, near the rear
|
J3 |
|-| |
|O| | (3.3V seen, open-circuit)
|O| | TXD
|O| | RXD
|O| |
|O| | GND
|-| |
|
Unimplemented:
* serial1 "ttyQHS0" (serial0 works as console)
* Bluetooth; Qualcomm CSR8811 (potentially conected to serial1)
Other Notes:
https://wikidevi.com/wiki/Linksys_EA8300 states
FCC docs also cover the Linksys EA8250. According to the
RF Test Report BT BR+EDR, "All models are identical except
for the EA8300 supports 256QAM and the EA8250 disable 256QAM."
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
for better identification. Also create SUPPORTED_DEVICES string from it
which corresponds to dts compatible string.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Convert whole target to Device Tree based board detection instead of
identifying devices by dts file name. With this we can drop mvebu.sh
translation script and rely on common method for model detection.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Add vendors in device names and also rename few device names, for easier
identyfying potential firmware to flash. The vendor and device string is
mainly derived from model/compatipble string in dts from particular
device, but since not all devices are well described, some of the renames
follow marketing names.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This version has important change for tegra boards which is reserving
32MB memory for Linux kernel instead of current 16MB.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is sold as a dual-band 802.11ac range extender. It has a sliding
switch for Extender mode or Access Point mode, a WPS button, a recessed
Reset button, a hard-power button, and a multitude of LED's, some
multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is
Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may
connect at 115200 bps, 8 data bits, no parity, 1 stop bit.
Specification:
- System-On-Chip: QCA9558
- CPU/Speed: 720 MHz
- Flash-Chip: Winbond 25Q128FVSG
- Flash size: 16 MiB
- RAM: 128 MiB
- Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3
- Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4
- PHY: Atheros AR8035-A
Installation:
If you can get to the stock firmware's firmware upgrade option, just feed
it the factory.img and boot as usual. As an alternative, TFTP the
factory.img to the bootloader.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[whitespace fix in DTS and reorder of make variables]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
We do not need to define an empty Build/Configure since
the default checks for existing ./configure and does nothing
in case nothing is found.
Similar for Build/Compile: we can remove the definition
when we only call the default.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Add U-Boot for NVIDIA Tegra based boards, with the first being CompuLab
TrimSlice. This is part of initial support for this board.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The PKG_MIRROR_HASH was for some reason wrong.
Fixes: d75db67870 ("uboot-fritz4040: bump version to 2019-03-03")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
- Former "mir3g" board name becomes "xiaomi,mir3g".
- Reorder some entries to maintain alphabetical order.
- Change DTS so status LEDs (yellow/red/blue) mimic
Xiaomi stock firmware: (Section Indicator)
<http://files.xiaomi-mi.co.uk/files/router_pro/router%20PRO%20EN.pdf>
<http://files.xiaomi-mi.co.uk/files/Mi_WiFi_router_3/MiWiFi_router3_EN.pdf>
|Yellow: Update (LED flickering), the launch of the system (steady light);
|Blue: during normal operation (steady light);
|Red: Safe mode (display flicker), system failure (steady light);
Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
[Added link to similar Router 3 model]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware
--------
CPU: Qualcomm IPQ4019
RAM: 256M (NANYA NT5CC128M16JR-EK)
FLASH: 128M NAND (Macronix MX30LF1G18AC-XKI)
ETH: Qualcomm QCA8072
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
WiFi5: QCA9984 4T4R 4SS n/ac
LED: - Connect green/blue/red
- Power green
BTN: WPS/Connect
UART: 115200n8 3.3V
VCC - RX - TX - GND (Square is VCC)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz3000'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz3000.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ3000.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz3000.bin uboot0
> mtd write /path/to/uboot-fritz3000.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware:
CPU: MediaTek MT7621AT (2x880MHz)
RAM: 512MB DDR3
FLASH: 256MB NAND
WiFi: 2.4GHz 4x4 MT7615 b/g/n (Needs driver, See Issues!)
WiFI: 5GHz 4x4 MT7615 a/n/ac (Needs driver, See Issues!)
USB: 1x 3.0
ETH: 1x WAN 10/100/1000 3x LAN 10/100/1000
LED: Power/Status
BTN: RESET
UART: 115200 8n1
Partition layout and boot:
Stock Xiaomi firmware has the MTD split into (among others)
- kernel0 (@0x200000)
- kernel1 (@0x600000)
- rootfs0
- rootfs1
- overlay (ubi)
Xiaomi uboot expects to find kernels at 0x200000 & 0x600000
referred to as system 1 & system 2 respectively.
a kernel is considered suitable for handing control over
if its linux magic number exists & uImage CRC are correct.
If either of those conditions fail, a matching sys'n'_fail flag
is set in uboot env & a restart performed in the hope that the
alternate kernel is okay.
If neither kernel checksums ok and both are marked failed, system 2
is booted anyway.
Note uboot's tftp flash install writes the transferred
image to both kernel partitions.
Installation:
Similar to the Xiaomi MIR3G, we keep stock Xiaomi firmware in
kernel0 for ease of recovery, and install OpenWRT into kernel1 and
after.
The installation file for OpenWRT is a *squashfs-factory.bin file that
contains the kernel and a ubi partition. This is flashed as follows:
nvram set flag_try_sys1_failed=1
nvram set flag_try_sys2_failed=0
nvram commit
dd if=factory.bin bs=1M count=4 | mtd write - kernel1
dd if=factory.bin bs=1M skip=4 | mtd write - rootfs0
reboot
Reverting to stock:
The part of stock firmware we've kept in kernel0 allows us to run stock
recovery, which will re-flash stock firmware from a *.bin file on a USB.
For this we do the following:
fw_setenv flag_try_sys1_failed 0
fw_setenv flag_try_sys2_failed 1
reboot
After reboot the LED status light will blink red, at which point pressing
the 'reset' button will cause stock firmware to be installed from USB.
Issues:
OpenWRT currently does not have support for the MT7615 wifi chips. There is
ongoing work to add mt7615 support to the open source mt76 driver. Until that
support is in place, there are closed-source kernel modules that can be used.
See: https://forum.openwrt.org/t/support-for-xiaomi-wifi-r3p-pro/20290/170
Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[02_network remaps, Added link to notes]
Hardware
--------
SOC: QCA9558
RAM: 128M DDR2
Flash: 16MiB SPI-NOR
ETH: QCA8337N: 2x 10/100/1000 PoE and PoE pass-through
WiFi2: QCA9558 (bgn) 2T2R
WiFi5: 2x mPCIE with AR9582 (an) 2T2R
BTN: 1x Reset
GPIO: multiple GPIO on header, PoE passthrough enable
UART: 3.3V 115200 8N1 header on the board
WDG: ATTiny13 watchdog
JTAG: header on the board
USB: 1x connector and 1x header on the board
PoE: 10-32V input in ETH port 1, passthrough in port 2
mPCIE: 2x populated with radios (but replaceable)
OpenWrt is preinstalled from factory. To install use <your-image>-sysupgade.bin
using the web interface or with sysupgrade -n.
Flash from bootloader (in case failsafe does not work)
1. Connect the LibreRouter with a serial adapter (TTL voltage) to the UART
header in the board.
2. Connect an ETH cable and configure static ip addres 192.168.1.10/24
3. Turn on the device and stop the bootloader sending any key through the serial
interface.
4. Use a TFTP server to serve <your image>-sysupgrade.bin file.
5. Execute the following commands at the bootloader prompt:
ath> tftp 82000000 <your image>-sysupgrade.bin
ath> erase 0x9f050000 +$filesize
ath> cp.b 0x82000000 0x9f050000 $filesize
ath> bootm 0x9f050000
More docs
* Bootloader https://github.com/librerouterorg/u-boot
* Board details (schematics, gerbers): https://github.com/librerouterorg/board
Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
Use tested values on shuttle,kd20 and assumed values for
mitrastar,stg-212 and cloudengines,pogoplug*.
akitio users have yet to report back stock flash layout to support
vendor bootloader environment there as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
CPU: Qualcomm IPQ4019
RAM: 256M
FLASH: 128M NAND
ETH: QCA8075
VDSL: Intel/Lantiq VRX518 PCIe attached
currently not supported
DECT: Dialog SC14448
currently not supported
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
LED: - Power/DSL green
- WLAN green
- FON/DECT green
- Connect/WPS green
- Info green
- Info red
BTN: - WLAN
- FON
- WPS/Connect
UART: 115200n8 3.3V (located under the Dialog chip)
VCC - RX - TX - GND (Square is VCC)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz7530'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ7530.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz7530.bin uboot0
> mtd write /path/to/uboot-fritz7530.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
[removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Adds support for the AVM FRITZ!Box 7530.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [PKG_RELEASE]
VBoxManage is not used and the image is created with proper permisions:
0f5d0f6 image: use internal qemu-img for vmdk and vdi images drop host
dependencies on qemu-utils and VirtualBox
Unreachable config symbols:
9e0759e x86: merge all geode based subtargets into one
No need to define those symbols since x86_64 is subtarget of x86:
196fb76 x86: make x86_64 a subtarget instead of a standalone target
Unreachable config symbols, so remove GRUB_ROOT:
371b382 x86: remove the xen_domu subtarget
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This commit adds support for the Linksys EA6350v3 device in the ipq40xx
target.
This is needed for uboot-envtools to access the environment. Without this
patch, the Linksys EA6350v3 will not be able to access the uboot
environment. As a side effect, the feature auto_recovery will make the
device unstable by switching between the latest and the current firmware.
Signed-off-by: Ryan Pannell <ryan@osukl.com>
Signed-off-by: Oever González <notengobattery@gmail.com>
CPU: FSL P1020 (2x 800MHz E500 PPC)
RAM: 1GB DDR3
FLASH: 256MiB NAND
WiFi: 2x Atheros AR9382 2x2:2 abgn
ETH: 2x BCM54616S - 1x BCM53128 8-port switch
LED: 5x LEDs (Power, WiFi1, WiFi2, N/D, SYS)
BTN: 1x RESET
Installation
------------
1. Download initrams kernel image, dtb binary and sysupgrade image.
2. Place initramfs kernel into tftp root directory. Rename to
"panda-uimage-factory".
3. Place dtb binary into tftp root directory. Rename to "panda.fdt".
4. Start tftp server on 192.168.100.8/24.
5. Power up the device with the reset button pressed. It will download
the initrams and dtb via tftp and boot into OpenWRT in RAM.
6. SSH into the device and remove the factory partitions.
> ubirmvol /dev/ubi0 --name=kernel1
> ubirmvol /dev/ubi0 --name=rootfs1
> ubirmvol /dev/ubi0 --name=devicetree1
You will have around 60 MiB of free space with that.
You can also delete "kernel2", "devicetree2", "rootfs2" and "storage"
respectively in case you do not want to go back to the vendor firmware.
7. Modify the U-Boot bootcmd to allow for booting OpenWRT
> fw_setenv bootcmd_owrt "ubi part ubi && ubi read 0x1000000 kernel
&& bootm 0x1000000"
> fw_setenv bootargs_owrt "setenv bootargs console=ttyS0,115200
ubi.mtd=3,2048"
> fw_setenv bootcmd "run bootargs_owrt; run bootcmd_owrt"
8. Transfer the sysupgrade image via scp into the /tmp directory.
9. Upgrade the device
> sysupgrade -n /tmp/<imagename>
Signed-off-by: David Bauer <mail@david-bauer.net>
On musl based distributions, u-boot 2010.03 fails to build with:
u-boot-2010.03/include/u-boot/crc.h:29:50: error: unknown type name 'uint'
uint32_t crc32 (uint32_t, const unsigned char *, uint);
The issue was fixed in the newer u-boot-2018.03 version, this commit
backports the change to the older version used by ar71xx/ath79.
Signed-off-by: Andy Walsh <andy.walsh44+github@gmail.com>
[add commit message from PR description]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The Detection pin is at PF6 and not at PH13 like defined before. I
checked the schematics and now I am am not seeing this error message any
more:
Loading Environment from FAT... Card did not respond to voltage select!
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Disable the PMIC on Olimex A13 Olinuxino, as the SPL cannot set the
core voltage correctly, which causes the board to freeze later at
kernel if CPU throttling is enabled (see below). This will almost
certainly kill the VGA output (which requires LDO3 to be set), but
this is still a better option than to disable CPU throttling for
all Cortex-A8 based devices.
[ 2.485632] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 384000 KHz
[ 2.525698] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 432000 KHz
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Instead of using a fork of the ARM trusted firmware specifically for the
Allwinner SoCs, use the official version from ARM now, this version
supports the Allwinner SoCs now and the older ATF repository is
deprecated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the uboot for the sunxi target to version 2018.11
The removed patches are applied upstream and not needed any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Copy U-Boot to STAGING_DIR_IMAGE (and append it to the EVA-image from
there) to fix image generation using the image-builder.
Also remove the bootloader from DEVICE_PACKAGES and instead use the
BUILD_DEVICES directive from within the U-Boot makefile.
This fixes eva-image generation using the OpenWRT image-builder.
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds the nescessary settings to allow reading the uboot environment variables on the GL.iNet GL-B1300 board.
Signed-off-by: Ibrahim Tachijian <barhom@netsat.se>
This device is called GL-AR300M, therefore rename the board(s)
to 'gl-ar300m-nor' and 'gl-ar300m-nand'
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
[change boardname in uboot envtools as well, don't use wildcards for
boardname]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The LS1021A-IoT gateway reference design based on the
QorIQ LS1021A processor is a purpose-built, small
footprint hardware platform with a wide array of
high-speed connectivity and low-speed serial interfaces
to support secure delivery of IoT services for home,
business or other commercial location.
- Combines standards-based, open source software with a
feature-rich IoT gateway design to establish a common,
open framework for secured IoT service delivery and
management.
- Provides a wide assortment of high-speed and serial-based
connectivity in a compact, highly secure design.
- High efficiency through the use of the Arm-based QorIQ
LS1021A embedded processor.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
After changing board names to DT compat string, we also need to
adjust the script which generates uboot-env configuration files.
Fixes: e880a30549 ("mxs: use generic sysinfo board detection")
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
According to https://github.com/openwrt/openwrt/pull/1527, support
for the Buffalo BHR-4GRV2 in ath79 requires repartitioning from
an initramfs image, make this easier by supporting uboot-envtools
support out of the box.
Build tested, but not runtime tested.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Port support for the Buffalo WZR-HP-AG300H from the ar71xx target to
ath79 as well.
Build- and runtime tested on the Buffalo WZR-HP-AG300H.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Beside one exception, no one took care of these two remaining boards
still using the legacy image build code during the last two years.
Since OpenWrt 14.07 the ALLNET ALL0239-3G image building is broken.
The Sitecom WL-341 v3 image build code looks pretty hackish and broken.
It's questionable if the legacy image works as all.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch updates the uboot-fritz4040 package to the latest version.
The portability and private-libgcc patches, as well as the
upload-to-f4040.sh script have been added to the upstream repository.
Furthermore, the upload-to-f4040 has been updated to take the first
parameter as the file it is supposed to flash, otherwise it defaults
to the previous "uboot-fritz4040.bin". Furthermore the error messages
have been improved and ftp will now dump some "progress information"
to the user's console.
Also included is support for gcc 8+ and a fix for the obnoxous error
that currently breaks the builders:
| fritz/src/lzma2eva.c:23:30: fatal error: zlib.h: No such file or directory
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for the Netgear WNDAP620 and WNDAP660,
they are similar devices, but due to the LAN LED configuration,
the switch setup and WIFI configuration each gets a different
device target.
Hardware Highlights WNDAP620:
CPU: AMCC PowerPC APM82181 at 1000 MHz
DRAM: 128 MB, 2 x 64 MiB DDR2 Hynix H5PS5162GF
CPU: AMCC PowerPC APM82181 at 1000 MHz
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY - Only 1 GBit Port (POE)
Wifi: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 3 internal dual-band antennae + 3 x RSMA for external antennaes
Hardware Highlights WNDAP660:
CPU: AMCC PowerPC APM82181 at 1000 MHz + 2 Heatsinks
DRAM: 256 MB, 2 x 128 MiB DDR2
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY (POE)
Wifi1: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Wifi2: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, 2x dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 6 internal dual-band antennae + 3 x RSMA for external antennaes
Flashing requirements:
- needs a tftp server at 192.168.1.10/serverip.
- special 8P8C(aka RJ45)<->D-SUB9 Console Cable
("Cisco Console Cable"). Note: Both WNDAP6x0 have
a MAX3232 transceivers, hence no need for any separate
CMOS/TTL level shifters.
External Antenna:
The antennae mux is controlled by GPIO 11 and GPIO14. Valid Configurations:
= Config# = | = GPIO 11 = | = GPIO 14 = | ===== Description =====
1. | 1 / High | 0 / Low | Use the internal antennae (default)
2. | 0 / Low | 1 / High | Use the external antennae
The external antennaes are only meant for the 2.4 GHz band.
One-way Flashing instructions via u-boot:
0. connect the serial cable to the RJ45 Console Port
Note: This requires a poper RS232 and not a TTL/USB adaptor.
1. power up the AP and interrupt the u-boot process at
'Hit any key to stop autoboot'
2. setup serverip and ipaddr env settings
Enter the following commands into the u-boot shell
# setenv ipaddr 192.168.1.1
# setenv serverip 192.168.1.10
3. download the factory.img image to the AP
Enter the following commands into the u-boot shell
# tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-squashfs-factory.img
4. verfiy image integrity
Enter the following commands into the u-boot shell
# crc32 $fileaddr $filesize
If the calculated crc32 checksum does not match, go back to step 3.
5. flash the image
Enter the following commands into the u-boot shell
# nand erase 0x110000 0x1bd0000
# nand write ${kernel_addr_r} 0x110000 ${filesize}
6. setup uboot environment
Enter the following commands into the u-boot shell
# setenv bootargs
# setenv fileaddr
# setenv filesize
# setenv addroot 'setenv bootargs ${bootargs} root=/dev/ubiblock0_0'
# setenv owrt_boot 'nboot ${kernel_addr_r} nand0 0x110000; run addroot; run addtty; bootm ${kernel_addr_r}'
# setenv bootcmd 'run owrt_boot'
# saveenv
7. boot
# run bootcmd
Booting initramfs instructions via u-boot:
Follow steps 0 - 2 from above.
3. boot initramfs
Enter the following commands into the u-boot shell
# tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-initramfs-kernel.bin
# run addtty
# bootm ${kernel_addr_r}
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds u-boot environment access to the MX60(W) target.
"The environment size is one NAND block (128KiB on Buckminster).
We allocate four NAND blocks to deal with bad blocks which may
exist in the saved environment"
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
All apm821xx devices use u-boot and most of them have
an accessible u-boot environment. This patch adds the
necessary template file, but does not add the
uboot-envtools package to any of the targets.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Also update the U-Boot BSP patch for I2SE Duckbill devices
and remove upstreamed patch for LibreSSL support.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
In dtc version 1.4.6 the macro names in header include guards changed,
but the build relies on them matching in order to replace selected
headers. This is a horrible hack to work around this.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
ls1012afrdm was no longer supported in NXP Layerscape SDK.
Instead a new board ls1012afrwy was introduced in LSDK.
This patch is to drop ls1012afrdm and add ls1012afrwy support.
Since only 2MB NOR flash could be used, we just put u-boot
and firmware on NOR flash, and put kernel/dtb/rootfs on SD
card.
The Layerscape FRWY-LS1012A board is an ultra-low-cost
development platform for LS1012A Series Communication
Processors built on Arm Cortex-A53. This tool refines the
FRDM-LS1012A with more features for a better hands-on experience
for IoT, edge computing, and various advanced embedded
applications. Features include easy access to processor I/O,
low-power operation, micro SD card storage, an M2 connector, a
small form factor, and expansion board options via mikroBUS Click
Module. The MicroBUS Module provides easy expansion via hundreds
of powerful modules supporting sensors, actuators, memories,
and displays.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
NOR/QSPI Flash on Layerscape board only has limited 64MB memory size.
Since some boards (ls1043ardb/ls1046ardb/ls1088ardb/ls1021atwr)
could support SD card boot, we added SD boot support for them to put
all things on SD card to meet large memory requirement.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The NXP TWR-LS1021A module is a development system based
on the QorIQ LS1021A processor.
- This feature-rich, high-performance processor module can
be used standalone or as part of an assembled Tower System
development platform.
- Incorporating dual Arm Cortex-A7 cores running up to 1 GHz,
the TWR-LS1021A delivers an outstanding level of performance.
- The TWR-LS1021A offers HDMI, SATA3 and USB3 connectors as
well as a complete Linux software developer's package.
- The module provides a comprehensive level of security that
includes support for secure boot, Trust Architecture and
tamper detection in both standby and active power modes,
safeguarding the device from manufacture to deployment.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to implement u-boot environment txt files
to support OpenWrt boot for all layerscape devices.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The u-boot source code had been migrated to codeaurora
for LSDK-18.06 release and the future release. This
patch is to update u-boot to LSDK-18.06 for both
uboot-layerscape and uboot-layerscape-armv8_32b packages.
Besides, this patch also introduced some other changes.
- Reworked uboot-layerscape makefile to make it more
readable.
- Define package in uboot-layerscape-armv8_32b for each board.
- Fixed u-boot package selection in target image makefile.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Dropped uboot-layerscape patches which were environemnt patches.
We will make u-boot environment binaries with a txt file for all
devices.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The NanoPi NEO2 is a small Allwinner H5 based board available with
different DRAM configurations.
This board is very similar to the NanoPi NEO PLUS2
Signed-off-by: Jasper Scholte <NightNL@outlook.com>
Follow the strategy of other targets and create a
default environment file, uEnv.txt, to configure the
behavior of U-Boot.
For now, use it to pass bootargs to the kernel
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Create a directory inside STAGING_DIR and copy U-Boot
output images, so they can be used later when creating the
sdcard image
Additionally, like others targets, override the default
install method to avoid copying the images to bin directory
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Select the U-Boot variant automatically based on the
current selected device, and hide the package from
menuconfig
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
The board was added when creating the target, but the
corresponding device was never defined inside the target
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
- Specifications -
CuBox i1:
- SoC: i.MX6 Solo
- Cores: 1
- Memory Size: 512MB
- GPU: GC880
- Wifi/Bluetooth: Optional
- USB 2.0 ports: 2
- Ethernet: 10/100/1000 Mbps
CuBox i2 | i2eX:
- SoC: i.MX6 Dual Lite
- Cores: 2
- Memory Size: 1GB
- GPU: GC2000
- Wifi/Bluetooth: Optional
- USB 2.0 ports: 2
- Ethernet: 10/100/1000 Mbps
CuBox i4Pro | i4x4:
- SoC: i.MX6 Quad
- Cores: 4
- Memory Size: 2/4 GB
- GPU: GC2000
- Wifi/Bluetooth: Build In
- USB 2.0 ports: 2
- Ethernet: 10/100/1000 Mbps
Built-in u-boot requires SPL (secondary program loader) to be present on the SD-card regardless of the image type which will be loaded.
SPL is generated by the u-boot-mx6cuboxi package which is preselected by the target device and can be found in bin/u-boot-mx6cuboxi directory.
Flashing the SPL:
dd if=/dev/zero of=/dev/mmcblk0 bs=1M count=4
dd if=bin/targets/imx6/generic/u-boot-mx6cuboxi/SPL of=/dev/mmcblk0 bs=1K seek=1
Preparing the firmware on the SD-card:
(echo o; echo n; echo p; echo 1; echo ''; echo ''; echo w) | fdisk /dev/mmcblk0
mkfs.ext4 /dev/mmcblk0p1
mount /dev/mmcblk0p1 /mnt
tar -xzf bin/targets/imx6/generic/openwrt-imx6-device-cubox-i-rootfs.tar.gz -C /mnt/
mkdir -p /mnt/boot
cp bin/targets/imx6/generic/{*-uImage,*.dtb,*.scr} /mnt/boot/
Generated u-boot.img needs to be placed on the first partition:
cp bin/targets/imx6/generic/u-boot-mx6cuboxi/u-boot.img /mnt/
To boot from the SD card:
Boot script which sets mmc/dtb parameters and boots the board is automatically sourced.
If this does not work for any reason:
mmc dev 0; load mmc 0:1 $scriptaddr boot/boot.scr; source $scriptaddr
Currently imx6dl-cubox-i.dtb (Dual Lite) and imx6q-cubox-i.dtb (Quad) device trees are available.
Tested on i4Pro, MMC, USB (+ HiD), HDMI and ethernet ports are working.
Wireless and bluetooth are broken ATM. According to SolidRun forums, BCM4329/BCM4330 firmware is used which works fine on older kernels.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Backport board support from the upcoming v2018.09 release,
and add an additional patch to read the MAC address
from flash memory
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Patch 300-CVE-2015-8370.patch was added without proper rebasing on the
version used by OpenWrt, make it apply and refresh the patch to fix
compilation.
Fixes: 7e73e9128f ("grub2: Fix CVE-2015-8370")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This CVE is a culmination of multiple integer overflow issues that cause
multiple issues like Denial of Service and authentication bypass.
More info: https://nvd.nist.gov/vuln/detail/CVE-2015-8370
Taken from Fedora.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This commit adds support for the OCEDO Koala
SOC: Qualcomm QCA9558 (Scorpion)
RAM: 128MB
FLASH: 16MiB
WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2: QCA9880 5 GHz 802.11nac 3x3
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
CPU: H5 High Performance Quad-core 64-bit Cortex-A53
GPU: Mali450 OpenGL ES 2.0/1.1/1.0, OpenVG 1.1, EGL
Memory: 1GB DDR3 (shared with GPU)
Onboard Storage: TF card (Max. 32GB) / NOR flash(2MB)
Onboard Network: 1000M/100M Ethernet RJ45
USB 2.0 Ports: Three USB 2.0 HOST, one USB 2.0 OTG, HOST mode
role by default in DTS
Buttons: Power Button(SW4) Debug TTL
UART: ..DC-IN..
>[GND][RX][TX] ..HDMI..
Signed-off-by: Antonio Silverio <menion@gmail.com>
This adds uci entries for all ath79 devices for which this already was
the case on ar71xx. Additionally we add the OCEDO Koala as there was no
support in OpenWRT yet.
Signed-off-by: David Bauer <mail@david-bauer.net>
* change mx6qsabresd to mx6qsabres to match defconfig name
* merge wanboard profiles since there is only one defconfig for the target device
* move wanboard options from wandboard.h to defconfig
* remove legacy patches
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
With current uboot default configuration the bootloader will
fail to start the OpenWrt firmware with the following error:
-----
unexpected character 'b' at the end of partition
Error initializing mtdparts!
incorrect device type in ubi
Partition ubi not found!
Error, no UBI device/partition selected!
Wrong Image Format for bootm command
Error occured, error code = 112
-----
If the uboot configuration is examined with printenv
I can see that mdtparts line (on a nsa310) is wrong:
-----
mtdparts=mtdparts=orion_nand:0x0c0000(uboot),
0x80000(uboot_env),0x7ec0000(ubi)bootargs_root=
----
The "bootargs_root=" that was appended to it should not be there.
Fix the issue by adding a \0 line terminator at the end of affected lines,
mimicking what is also done by uboot upstream.
This issue was detected and confirmed on a nsa310, nsa325 and
a pogoplug v4, but it's not hardware-specific, so apply the same fix
to other devices as well.
Note that the issue is with the uboot's integrated boot configuration,
which is not used unless the uboot configuration in flash is unavailable
(erased or corrupted), which happens only on first time installation,
or if the user deletes the uboot configuration when upgrading uboot.
People just upgrading from an older uboot without erasing their previous
uboot configuration stored in flash would not have noticed this issue.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
This patch adds support for ZyXEL NBG6617
Hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR: 32 MiB Macronix MX25L25635F
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS
Serial:
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
pre-soldered. Pinout:
1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX
first install / debricking / restore stock:
0. Have a PC running a tftp-server @ 192.168.1.99/24
1. connect the PC to any LAN-Ports
2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
into the tftp-server root directory and rename it to just "ras.bin".
3. power-cycle the router and hold down the the WPS button (for 30sek)
4. Wait (for a long time - the serial console provides some progress
reports. The u-boot says it best: "Please be patient".
5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
flashes fast at the same time. You have to reboot the device and
it should then come right up.
Installation via Web-UI:
0. Connect a PC to the powered-on router. It will assign your PC a
IP-address via DHCP
1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
2. Go to the "Expert Mode"
3. Under "Maintenance", select "Firmware-Upgrade"
4. Upload the OpenWRT factory image
5. Wait for the Device to finish.
It will reboot into OpenWRT without any additional actions needed.
To open the ZyXEL NBG6617:
0. remove the four rubber feet glued on the backside
1. remove the four philips screws and pry open the top cover
(by applying force between the plastic top housing from the
backside/lan-port side)
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6617> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6617>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
|NBG6617> ATSE NBG6617
|012345678901
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711
copy and paste the result into the shell to unlock zloader.
|NBG6617> ATEN 1,0046B0017430
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
|NBG6617> ATGU
|NBG6617#
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
The device tree files are now matching the kernel 4.17 and this will be
send also for integration into mainline U-Boot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch 220-add-sunxi50i-nanopi-neo-plus2.patch was merged upstream.
The u-boot-sunxi-with-spl.bin is now also created for the ARM64 sunxi
boards by U-Boot itself, no need to do it manually any more.
This was tested on a H2+ Orange Pi R1 and a H5 Orange Pi Zero Plus.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for the OCEDO Koala
SOC: Qualcomm QCA9558 (Scorpion)
RAM: 128MB
FLASH: 16MiB
WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2: QCA9880 5 GHz 802.11nac 3x3
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Reboot the oxnas target based on Linux 4.14 by rebasing our support on
top of the now-existing upstream kernel support.
This commit brings oxnas support to the level of v4.17 having upstream
drivers for Ethernet, Serial and NAND flash.
Botch up OpenWrt's local drivers for EHCI, SATA and PCIe based on the
new platform code and device-tree.
Re-introduce base-files from old oxnas target which works for now but
needs further clean-up towards generic board support.
Functional issues:
* PCIe won't come up (hence no USB3 on Shuttle KD20)
* I2C bus of Akitio myCloud device is likely not to work (missing
debounce support in new pinctrl driver)
Code-style issues:
* plla/pllb needs further cleanup -- currently their users or writing
into the syscon regmap after acquireling the clk instead of using
defined clk_*_*() functions to setup multipliers and dividors.
* PCIe phy needs its own little driver.
* SATA driver is a monster and should be split into an mfd having
a raidctrl regmap, sata controller, sata ports and sata phy.
Tested on MitraStar STG-212 aka. Medion Akoya MD86xxx and Shuttle KD20.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The uboot-mvebu package incorrectly used the host pkg-config for the tool
build parts, which broke the build on systems lacking pkg-config and only
worked by accident on those that have it installed.
Export the host-build specific environment variables for the uboot build
to redirect pkg-config invocations to our staged host build pkg-config in
buildroot.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The uboot-mvebu package incorrectly used the host pkg-config for the tool
build parts, which broke the build on systems lacking pkg-config and only
worked by accident on those that have it installed.
Export the host-build specific environment variables for the uboot build
to redirect pkg-config invocations to our staged host build pkg-config in
buildroot.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The uboot-mvebu package incorrectly used the host pkg-config for the tool
build parts, which broke the build on systems lacking pkg-config and only
worked by accident on those that have it installed.
Export the host-build specific environment variables for the uboot build
to redirect pkg-config invocations to our staged host build pkg-config in
buildroot.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Linksys WRT32X (Venom) is identical in hardware to the WRT3200ACM
with a different flash layout and boots zImage rather than uImage.
Specification:
- Marvell Armada 385 88F6820 (2x 1.8GHz)
- 256MB of Flash
- 512MB of RAM
- 2.4GHz (bgn) and 5GHz (an+ac wave 2)
- 4x 1Gbps LAN + 1x 1Gbps WAN
- 1x USB 3.0 and 1x USB 2.0/eSATA (combo port)
Flash instruction:
Apply factory image via web-gui.
Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
Add target device as at91-sama5d2_ptc_ek in SAMA5D2 subtarget and
build images for SAMA5D2 PTC Ek board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
reorganizing at91 subtargets based on sama5 soc features and this fix
below problems.
1. able to set neon flags to sama5d2 & sama5d4 subtargets.
2. fix the make clean which removes all the subtargets in bin folder.
3. able to configure kernel specific to subtarget.
4. able to set vfpu4 flags to samad3 subtargets.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
fixed DTC command not found error while compling uboot-at91. The fix
is to set DTC PATH in uboot-at91 MAKE command.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D27 SOM1 with target device as at91-sama5d27_som1_ek
in SAMA5 subtarget and build images for SAMA5D27 SOM1 Ek board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
fetching uboot src from linux4sam/u-boot-at91 github for all at91
target.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
updating to new version v3.8.10 and copying at91bootstrap.bin to bin folder.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Currently, the build system uses an openwrt mirror which does not currently
work and FTP can be unreliable under several circumstances. This change
implicitly allows using all the mirrors to download.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
When libressl was linked the libpthread was missing, add it in addition.
Fixes: 2c192b6916 ("tools/libressl: update to version 2.7.2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When libressl was linked the libpthread was missing, add it in addition.
Also make the mxsimage tool to use the OpenSSL 1.1 API for the recent
libressl version.
Fixes: 2c192b6916 ("tools/libressl: update to version 2.7.2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When libressl was linked the libpthread was missing, add it in addition.
Fixes: 2c192b6916 ("tools/libressl: update to version 2.7.2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Added for convenience. These boards can be used as dev boards running
various operating systems from different media, and this simplifies work
with U-Boot environment.
Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ 802.3at POE+
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 18-24V passive POE (mode B)
* powered only via POE
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
The initramfs image can be started using
setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
set fdt_high 0x85000000
bootm 0x84000000
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Several changes has been made:
+ AES support has been removed by
upstream commit c6831c7 (2017-11-14)
[remove patch "200-fw_env_no_aes.patch"]
+ Support for UBI volumes has beed added by
upstream commit 34255b9 (2017-11-15)
[remove patch "300-support-env-in-ubivol-chardev.patch"]
+ A command line argument has beed added ("-c") to manually indicate
the location of the environment configuration file
Also, patch "400-u-boot-2015.10-stdint.patch" is no longer
necessary, and the config option to enable UBI support has
been removed.
Size comparisons:
fw_printenv size:
Target Before After
ar71xx 15,189 bytes 18,133 bytes (+2,944 bytes)
ipq40xx 20,873 bytes 20,987 bytes (+114 bytes)
mvebu 20,881 bytes 20,991 bytes (+110 bytes)
ramips 15,128 bytes 18,072 bytes (+2,944 bytes)
OPKG package size:
Target Before After
ar71xx 11,309 bytes 12,875 bytes (+1,566 bytes)
ipq40xx 11,772 bytes 13,299 bytes (+1,527 bytes)
mvebu 11,609 bytes 13,114 bytes (+1,505 bytes)
ramips 10,975 bytes 12,503 bytes (+1,528 bytes)
Compile tested: ipq40xx (musl, glibc, gcc5-musl), ar71xx, mvebu, ramips
Run tested: ipq40xx (ASUS RT-AC58U)
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
The serial was working before, but not when doing copy&pasting longer
commands in a short time.
Fixes: a4def18f29 ("uboot-omap: Update to u-boot v2017.01")
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
This release brings various improvements to clearfog support, such as distro-boot.
Obsoletes:
0002-clearfog-reset-usom-onboard-1512-phy.patch
0003-clearfog-enable-distro-boot-code.patch
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
CONFIG_* variables can easily be set by overriding Build/Configure.
so set NET_RANDOM_ETHADDR=y and CMD_SETEXPR=y here.
This replaces the following patches:
0001-clearfog-generate-random-MAC-address.patch
0004-clearfog-enable-setexpr-command-by-default.patch
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
We use the dtc from the kernel and that does not have all the options
which u-boot would like to use now. make these parameters optional.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[wigyori@uid0.hu: renamed to 221-compatible-old-dtc.patch from 220-]
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
U-Boot now requires GCC > 5
Catch up with upstream and move some configuration options from
the header files to the corresponding defconfig files.
Also move some options of patch 010 affecting the whole platform
to 010's device only.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Use the UBOOT_MAKE_FLAGS defined in include/u-boot.mk and do not
overwrite them to compile the host tools against the shipped LibreSSL.
In addition add a patch to fix a compile problem when compiling the
tools against LibreSSL caused by differences in the API between OpenSSL
1.1 and LibreSSL.
This should fix the compile problems seen in build bot from time to time
by not depending on the host libssl-dev package any more but using the
LibreSSL version from OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
