openwrt/package/boot
Jeff Kletsky 819e7946b0 ipq40xx: Add support for Linksys EA8300 (Dallas)
The Linksys EA8300 is based on QCA4019 and QCA9888 and provides three,
independent radios. NAND provides two, alternate kernel/firmware
images with fail-over provided by the OEM U-Boot.

Installation:

  "Factory" images may be installed directly through the OEM GUI.

Hardware Highlights:

  * IPQ4019 at 717 MHz (4 CPUs)
  * 256 MB NAND (Winbond W29N02GV, 8-bit parallel)
  * 256 MB RAM
  * Three, fully-functional radios; `iw phy` reports (FCC/US, -CT):
      * 2.4 GHz radio at 30 dBm
      * 5 GHz radio on ch. 36-64 at 23 dBm
      * 5 GHz radio on ch. 100-144 at 23 dBm (DFS), 149-165 at 30 dBm
      #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1
      * All two-stream, MCS 0-9
  * 4x GigE LAN, 1x GigE Internet Ethernet jacks with port lights
  * USB3, single port on rear with LED
  * WPS and reset buttons
  * Four status lights on top
  * Serial pads internal (unpopulated)

  "Linksys Dallas WiFi AP router based on Qualcomm AP DK07.1-c1"

Implementation Notes:

  The OEM flash layout is preserved at this time with 3 MB kernel and
  ~69 MB UBIFS for each firmware version. The sysdiag (1 MB) and
  syscfg (56 MB) partitions are untouched, available as read-only.

Serial Connectivity:

  Serial connectivity is *not* required to flash.

  Serial may be accessed by opening the device and connecting
  a 3.3-V adapter using 115200, 8n1. U-Boot access is good,
  including the ability to load images over TFTP and
  either run or flash them.

  Looking at the top of the board, from the front of the unit,
  J3 can be found on the right edge of the board, near the rear

      |
   J3 |
  |-| |
  |O| | (3.3V seen, open-circuit)
  |O| | TXD
  |O| | RXD
  |O| |
  |O| | GND
  |-| |
      |

Unimplemented:

    * serial1 "ttyQHS0" (serial0 works as console)
    * Bluetooth; Qualcomm CSR8811 (potentially conected to serial1)

Other Notes:

    https://wikidevi.com/wiki/Linksys_EA8300 states

        FCC docs also cover the Linksys EA8250. According to the
	RF Test Report BT BR+EDR, "All models are identical except
	for the EA8300 supports 256QAM and the EA8250 disable 256QAM."

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-05-18 13:43:54 +02:00
..
apex apex: Remove dead URL. 2018-08-22 11:21:53 +02:00
arm-trusted-firmware-sunxi arm-trusted-firmware-sunxi: Replace with official ARM version 2019-01-13 17:35:14 +01:00
at91bootstrap at91: Add SAMA5D2 PTC EK board 2018-05-05 06:55:22 +02:00
fconfig fconfig: cleanup Makefile 2019-04-06 19:14:06 +02:00
grub2 build: remove leftovers from previous x86 commits 2019-02-17 18:22:40 +01:00
imx-bootlets treewide: clean up download hashes 2016-12-16 22:39:22 +01:00
kexec-tools kexec-tools: bump version to 2.0.16 2018-02-11 16:10:51 +01:00
kobs-ng kobs-ng: add header for integer definitions 2017-11-16 22:56:54 +01:00
rbcfg rbcfg: Implement CPU frequency control 2017-10-07 15:00:26 +02:00
uboot-ar71xx uboot-ar71xx: fix musl host build 2019-01-22 13:29:46 +01:00
uboot-at91 at91: Add SAMA5D2 PTC EK board 2018-05-05 06:55:22 +02:00
uboot-envtools ipq40xx: Add support for Linksys EA8300 (Dallas) 2019-05-18 13:43:54 +02:00
uboot-fritz4040 uboot-fritz4040: fix PKG_MIRROR_HASH 2019-03-21 00:57:54 +01:00
uboot-imx6 uboot-imx6: Add support for Toradex Apalis board family 2019-04-08 18:37:03 +02:00
uboot-kirkwood uboot-kirkwood: update to 2019.01 2019-02-17 19:22:39 +01:00
uboot-lantiq uboot-lantiq: fix compile with modern host dtc 2018-10-07 02:12:06 +02:00
uboot-layerscape layerscape: add LS1021AIOT board support 2018-12-18 20:17:23 +01:00
uboot-layerscape-armv8_32b layerscape: add ls1012afrwy support and drop ls1012afrdm 2018-09-22 21:20:57 +02:00
uboot-mvebu mvebu: align device names to vendor_device format 2019-05-11 23:11:04 +02:00
uboot-mxs uboot-mxs: bump to v2019.01 2019-01-26 21:46:32 +01:00
uboot-omap package/uboot-omap: backport patches to fix build 2019-03-28 02:10:12 +01:00
uboot-oxnas uboot-oxnas: fix typo accidentally committed during oxnas reboot 2018-06-18 18:55:19 +02:00
uboot-sunxi uboot-sunxi: add fix for A20-OLinuXino-Lime2-eMMC rev. K boards 2019-03-13 22:43:13 +01:00
uboot-tegra tegra: add vendor string to device name 2019-05-15 13:34:23 +02:00
uboot-zynq uboot-zynq: use a file to modify the default environment 2018-09-10 08:54:41 +02:00