omcproxy will not start up if either the downlink or uplink interface is
not up at boottime as the interface triggers are not correctly
installed.
Further rework omcproxy init to make use of network functions defined
in network.sh; set proper family and proto options in procd firewall
rules.
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Specs
SoC: MT7621AT
RAM: 512MiB
Flash: 32MiB MX25L25635F SPI NOR
2.4G: MT7603EN
5G: MT7612EN
Ethernet: 4x GE ports (1x WAN, 3x LAN) with link status LEDs
USB 3.0
LEDs: POWER, 5G WIFI, 2.4G WIFI, USB, Internet.
The last two ones are controlled by GPIO
UART: There are 2 UARTs (UARTLITE1/ttyS0 and UARTLITE3/ttyS1) on board.
UARTLITE1 is close to LEDs, and UARTLITE3 is close to flash chip.
The stock u-boot uses UARTLITE1 by default. Baud rate is 57600
Flash instruction
1. telnet 192.168.9.1 2317, username is "root" and password is "admin"
One can alternatively use UART to log in
2. Put OpenWrt firmware in a FAT32 USB drive, and connect it to the router
One can alternatively download the firmware via wget through Internet
3. mtd write /path/to/openwrt.bin firmware
4. reboot
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Very similar to the DWR-921-C1, except has a telephony/RJ11 port (not
sure if supported, I didn't try), wireless router with QMI LTE embedded
modem is based on the MT7620N SoC.
Specification:
* MediaTek MT7620N (580 Mhz)
* 64 MB of RAM
* 16 MB of FLASH
* 802.11bgn radio
* 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
* 2x external, detachable (LTE) antennas
* UART header on PCB (57600 8n1)
* 6x LED (GPIO-controlled)
* 1x bi-color Signal Strength LED (GPIO-controlled)
* 2x button
* JBOOT bootloader
The status led has been assigned to the dwr-922-e2:green:signalstrength
(lte signal strength) led. At the end of the boot it is switched off and
is available for lte operation. Works correctly also during sysupgrade
operation.
Installation:
Apply factory image via d-link http web-gui, or via recovery interface:
How to recover/revert to OEM firmware:
1.) Push and hold the reset button and turn on the power. Wait until all
LEDs start rapidly blinking (~10sec.)
2.) DHCP should give you an IP in the 192.168.123.0/24 subnet, or set
one manually
3.) Upload original factory image via JBOOT http interface at IP
192.168.123.254
4.) If http doesn't work, it can be done with curl command:
curl -F FN=@XXXXX.binhttp://192.168.123.254/upg
where XXXXX.bin is name of firmware file.
5.) You can optionally telnet to 192.168.123.254 before or during the
upload and it will report the flashing status, memory address etc.
6.) Once web UI and/or telnet says "Success", power cycle the router, or
type "reboot" into the telnet session.
Signed-off-by: Simon Quigley <squigley@squigley.net>
[squashed commits, word wrap commit message, rename signal strenght led
name to match what is used for the DWR-921-C1 since they share the led
configuration, add label referenced in the aliases node]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The WD MyBook Live SquashFS images didn't work anymore due to
a upstream regression in f2fs commit: 0cfe75c5b01199
("f2fs: enhance sanity_check_raw_super() to avoid potential overflows")
that got backported to 4.14.86 and landed in 4.18.
by Martin Blumenstingl:
|Treat "block_count" from struct f2fs_super_block as 64-bit little endian
|value in sanity_check_raw_super() because struct f2fs_super_block
|declares "block_count" as "__le64".
|
|This fixes a bug where the superblock validation fails on big endian
|devices with the following error:
| F2FS-fs (sda1): Wrong segment_count / block_count (61439 > 0)
| F2FS-fs (sda1): Can't find valid F2FS filesystem in 1th superblock
| F2FS-fs (sda1): Wrong segment_count / block_count (61439 > 0)
| F2FS-fs (sda1): Can't find valid F2FS filesystem in 2th superblock
|As result of this the partition cannot be mounted.
|
|With this patch applied the superblock validation works fine and the
|partition can be mounted again:
| F2FS-fs (sda1): Mounted with checkpoint version = 7c84
|
|My little endian x86-64 hardware was able to mount the partition without
|this fix.
|To confirm that mounting f2fs filesystems works on big endian machines
|again I tested this on a 32-bit MIPS big endian (lantiq) device.
Hopefully, this will do until Martin's patch moved through upstream
to -stable.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The MyBook Live DUO used "wd,mybooklive-duo" as the first
compatible string and not "wd_mybooklive-duo".
Fixes: 9b47aa93c7 ("apm821xx: unify My Book Live Single + Duo images")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Currently all Archer A7 v5 have the same (incorrect) MAC address.
The address is currently derived from eth1 which is not present on the
QCA9563. Use eth0 to get the correct MAC address.
Signed-off-by: David Bauer <mail@david-bauer.net>
dd508af iwinfo: fix QCA9984 vendor id
0eaabf1 iwinfo: add device id for Atheros AR9287
6e998ec iwinfo: add device id for MediaTek MT7612E
5aa8c54 libiwinfo: nl80211: add mesh stats on assoclist.
77a9e98 iwinfo: Add Mikrotik R11e-2HPnD and R11e-5HacT to hardware list
Signed-off-by: Mathias Kresin <dev@kresin.me>
This reverts commit fd569e5e9d.
After an extra review & discussion few concerns were raised regarding
that feature:
1) It reacts to hotplug.d "block" events instead of more accurate (but
currently unavailable) "mount" events.
2) It requires *something* to mount block device before samba hotplug.d
gets fired. Otherwise samba_add_section() will just return.
3) It doesn't reload Samba which some users may expect
4) It operates on /etc/ which is not a right place for autogenerated
ephemeral config.
5) It doesn't include any cleanup for non-existing shares.
Cc: Rosy Song <rosysong@rosinson.com>
Cc: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
417ab77 mt7603: improve recovery from PSE reset failure
fea7ad8 mt76: move mt76x02_phy_get_min_avg_rssi to mt76 core
9d009be mt7603: add dynamic sensitivity tuning based on false CCA events
2c8e9ac mt7603: initialize channel maximum power from eeprom data
b2cc29b mt76: move mt76x02_get_txpower to mt76 core
6203d46 mt7603: add support for setting transmit power
294e095 mt7603: reset DMA scheduler on MT7628
8178f0d mt7603: apply efuse data only when it exists
e67e551 mt76: dma: remove napi from mt76_dma_rx_fill signature
0490bd2 mt76: usb: do not build the skb if reported len does not fit in buf_size
eb076ae mt76: Add missing include of linux/module.h
1d2819e mt76: fix typo in mt76x02_check_mac_err routine
9c9fae3 mt76: mac: run mt76x02_mac_work routine atomically
6be90b6 mt76: usb: avoid queue/status spinlocks while passing tx status to mac80211
40dad32 mt76x0: pci: fix ACS support
d94e9c4 mt76x02: do not set protection on set_rts_threshold callback
0d83d73 mt76x02: fixup MT_PROT_RATE_* defines
628f8d7 mt76x02: set protection according to ht operation element
f7d8c17 mt76x0: configure MT_VHT_HT_FBK_CFG1
10f57cf mt76x2: add static qualifier to mt76x2_init_hardware
37b2ad3 mt76: dfs: run mt76x02_dfs_set_domain atomically
51b6daf mt76x2: init: set default value for MT_TX_LINK_CFG
9661da4 mt76: add energy detect CCA support to mt76x{0,2}e drivers
876d0e9 mt76: mac: minor optimizations in mt76x02_mac_tx_rate_val
c78e317 mt76: dma: do not build skb if reported len does not fit in buf_size
3598046 mt76: mmio: introduce mt76x02_check_tx_hang watchdog
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch converts the MyBook Live's recovery image to utilize the
multi-image method which integrates the device-tree binary directly
into the image.
The new initramfs can be loaded through the MyBook Live's U-boot
in the following way:
=> setenv ipaddr 192.168.1.1
=> setenv serverip 192.168.1.2
=> sata init; run addtty; tftp $kernel_addr_r wd_mybooklive-initramfs.bin; bootm
Waiting for PHY auto negotiation to complete... done
ENET Speed is 1000 Mbps - FULL duplex connection (EMAC0)
Using ppc_4xx_eth0 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'wd_mybooklive-initramfs.bin'.
Load address: 0x1000000
Loading: ################################################ [...]
done
[...]
Booting kernel from Legacy Image at 01000000 ...
Image Name: initramfs
Image Type: PowerPC Linux Multi-File Image (gzip compressed)
[...]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch fixes the build regression on 4.14 build
due to dt-bindings/dma/dw-dmac.h MIA.
apm82181.dtsi:24:10: fatal error: dt-bindings/dma/dw-dmac.h: No such file or directory
Fixes: 32141c183a ("apm821xx: add linux 4.19 apm821xx patches")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
It's same for Bullet and Nanostation so far, so let's hope it's going to
be the same for other boards sharing the same platform.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It's not necessary as it's already defined in ar934x.dtsi to:
pll-data = <0x16000000 0x00000101 0x00001616>;
And in ar71xx it's currently set to the same values:
#define AR934X_PLL_VAL_1000 0x16000000
#define AR934X_PLL_VAL_100 0x00000101
#define AR934X_PLL_VAL_10 0x00001616
And dumping the value from the airOS v6.1.7 has the same value:
AR934X_PLL_ETH_XMII_CONTROL_REG 0x1805002C 0x101
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Currently there is no LED signalization for various system states
implemented in diag.sh, so this patch adds support for it.
Tested-by: Joe Ayers <ae6xe@arrl.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch updates the apm821xx target to use the 4.19 kernel.
4.19 ships with all the crypto4xx driver patches. Furthermore,
the DW-DMA fix for the SATA controller has been backported from
4.20 and integrated.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|In the patch "usb: simplify usbport trigger" together with
|"leds: triggers: add device attribute support" caused an
|regression for the usbport trigger. it will no longer
|enumerate any "ports" (i.e the sysfs directory stays empty)
|if the usb host drivers are fully initialized before the
|usbport trigger was loaded.
<https://marc.info/?l=linux-usb&m=154577101631079>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Thanks to the ledtrig-usb.c the USB LED trigger can be
setup in the device-tree definition for the Asus RT-AC58U
and ZyXEL NBG6617.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch fixes a kernel warning that got triggered by 4.19
because of a bad/missing interrupt level definition in the DTS.
| WARNING: CPU: 2 PID: 1996 at drivers/irqchip/irq-gic.c:1016
| CPU: 2 PID: 1996 Comm: kmodloader Not tainted 4.19.9 #0
| Hardware name: Generic DT based system
| [<c0317884>] (warn_slowpath_null) from [<c04f9cd0>]
| [<c04f9cd0>] (gic_irq_domain_translate) from [<c035af30>]
| [<c035af30>] (irq_create_fwspec_mapping) from [<c035b1e0>]
| [<c035b1e0>] (irq_create_of_mapping) from [<c0614eec>]
| [<c0614eec>] (of_irq_get) from [<c0614f3c>]
| [<c0614f3c>] (of_irq_to_resource) from [<c0614ff0>]
| [<c0614ff0>] (of_irq_to_resource_table) from [<c0610e08>]
| [<c0610e08>] (of_device_alloc) from [<c0610ea0>]
| [<c0610ea0>] (of_platform_device_create_pdata)
| [<c061120c>] (of_platform_bus_create)
| [<c06113c4>] (of_platform_populate)
| [<bf4c06b4>] (dwc3_qcom_probe [dwc3_qcom])
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Robert Marko <robimarko@gmail.com> noted in
"ipq40xx: Use kmod-usb-dwc3-qcom by default":
| Since 4.18 we cant use DWC3 OF Simple anymore so we
| have to use kmod-usb-dwc3-qcom.
This patch adds a TODO right next to the KERNEL_PATCHVER so
it will be picked up when moving to 4.19.
I would also like to point out:
All users/devs that are compiling their own images from source
and have a existing 4.14 config and want to switch to 4.19:
Please drop kmod-usb-dwc3-of-simple and add kmod-usb-dwc3-qcom
module package. Otherwise, the USB port on your router will no
longer work.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
- 4.19 no longer refuses to initialize the mdio bus if
a phy is not connected.
- fix partition unit-address
- restrict partition offset and size to 32-bit integers.
- add note to warn people not to mess with the ubi
partition size.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Upstream commit:
80483c3abf8 ("ARM: qcom: Cleanup/Remove unnecessary board file")
removed all the platform device compatibles stating that:
"This patch removes the unnecessary board file. The generic machine
definition is sufficient for the Qualcomm platforms."
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
- make the device userspace integration (WIFI,MAC,sysupgrade)
work again by renaming the ubi to UBI_DEV as a temporary measure.
In the future, once 4.14 support is dropped, this can all be
refactored again. *sigh*
- use the wifi0 and wifi1 labels
- follow Device-Tree Release v0.2 2.2.2 Generic Names Recommendation
- fix duplicated partition node-names
- remove qcom,ipq4019 platform compatible. it's no longer needed
(and wrong because the chip is a qcom,ipq4018).
Fixes: 4c67f3ad78d ("ipq40xx: Adapt 4.19 DTS for upstream SPI-NAND driver")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
IPQ40xx series has a HW pseudo random number generator built in.
It already has a node in the upstream ipq4019.dtsi so we just need to enable it.
Its driver has been rewritten to use crypto API so we dont have char interface like under 4.14 kernel.
Signed-off-by: Robert Marko <robimarko@gmail.com>
DTC was throwing warnings like this:
image-qcom-ipq4018-jalapeno.dtb: Warning (avoid_unnecessary_addr_size): /soc/spi@78b5000/m25p80@0: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
image-qcom-ipq4018-jalapeno.dtb: Warning (avoid_unnecessary_addr_size): /soc/spi@78b5000/spi-nand@1: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
So lets fix this for our downstream boards.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since 4.19 upstream kernel provides generic SPI-NAND
framework and vendor specific drivers.
Since only users of MT29F are 2 boards with Winbond
W25N01GV SPI-NAND for which support has been backported
from 4.20 we can drop the ever stuck in staging MT29F
driver and instead use the upstream driver.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [squashed]
Since kernel 4.18 support for Qualcomm glue layer was
moved from DWC3 OF Simple to a separate DWC3 QCOM module.
So lets add it and make it depend on 4.19 kernel and make
sure that DWC3 OF Simple is not included if 4.19 is used.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This adds the necessary patches for 4.19 kernel.
Upstreamed patches were dropped, backported upstreamed patches
from 4.20.
Drop Winbond ID patch since that NAND IC was upstreamed to use
SPI-NAND framework and support for it was backported from 4.20.
Rework ESSEDMA patches to compile under 4.19 due to timer changes,
Clément Péron did the hard work and his changes were taken from the
initial 4.19 PR.
MR33 changes had to be manually refreshed to apply.
Refresh other patches to apply.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN: 1x Reset
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to reset-button
There is also a Micro-B USB-port present but this only seems to be a
dummy as the circuit next to it is not present (at least in my unit).
It is also not mentioned in the devolo manual.
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
1x Atheros AR8033
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN: 1x Reset
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to reset-button
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds support for TP-Link Archer C7 v5, leveraging most effort
from commit ea9baee and 1e4ee63. Archer C7 v5 is identical to Archer A7 v5
but with a different flash layout.
Specification:
- QCA9563 SoC (750 MHz)
- 128 MiB of RAM (DDR2)
- 16 MiB of flash (SPI)
- 5x 1 Gbps Ethernet (1x WAN + 4x LAN)
- 2.4GHz (bgn) SoC internal + 5GHz (ac) QCA9880
- 10x LED, 2x button
- UART header on PCB
Flash instructions:
1. Upload openwrt-ath79-generic-tplink_archer-c7-v5-squashfs-factory.bin
via web interface.
Flash instructions using TFTP recovery:
1. Plug PC to one of the LAN ports
2. Set PC to fixed IP address 192.168.0.66
3. Rename the factory image to ArcherC7v5_tp_recovery.bin and place it in
TFTP root directory
4. Turn on the router with the reset button pressed for about 15 secs
5. Release the button and wait about 150 secs to complete flashing
Signed-off-by: TOCK Chiu <tock.chiu@gmail.com>
Even with squashfs brcm2708 requires ROOTFS_PART_SIZE because the overlay
exists as a loopback device on the space not used by squashfs in the root
partition. Also for ext4 (the other fs option) ROOTFS_PART_SIZE is required,
so use feature flag rootfs-part to enable it.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
The rootfs-part feature flag ensures that
CONFIG_ROOTFS_PART_SIZE symbol will be present
at all times.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Start 03x with 030 instead of 035. It's a trivial change that adds more
place for further backports in the 03x space.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The configuration option was renamed with kernel 4.19 from
CONFIG_CC_STACKPROTECTOR to CONFIG_STACKPROTECTOR adapt the code to set
both options.
CONFIG_STACKPROTECTOR now sets the regular stack protector and
CONFIG_STACKPROTECTOR_STRONG activates the additional protection of more
functions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With kernel 4.19 new configuration options for the compiler were added.
These are automatically selected and set, instead of having them in each
target configuration, put them into the generic configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>