Commit Graph

29053 Commits

Author SHA1 Message Date
Tianling Shen
dd8972fde3 rockchip: move image generation command to default
It's applicable for all devices so move it to default to reduce
redudant code. Addtionally introduce a new variable `BOOT_SCRIPT`
to allow custom boot script (if necessary).

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-11-26 19:44:56 +01:00
Tony Ambardar
a7818e0550 ipq40xx: enable UBI size checks for some Linksys NAND devices
Add correct NAND_SIZE in device definitions for EA6350v3, EA8300, MR8300,
WHW01 and WHW03v2, to enable improved image size checks wrt UBI reserved
blocks on NAND devices.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2023-11-26 18:37:21 +01:00
Tony Ambardar
b16e14a220 image: use helper function for size units
Add the make function 'exp_units' for helping evaluate k/m/g size units in
expressions, and use this to consistently replace many ad hoc substitutions
like '$(subst k,* 1024,$(subst m, * 1024k,$(IMAGE_SIZE)))' in makefiles.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2023-11-26 18:37:20 +01:00
Tony Ambardar
c66511bc48 ipq40xx: fix typo in Linksys WHW01 image definition
Use lower-case "k" in IMAGE_SIZE for Linksys WHW01, permitting proper unit
conversions in build recipes (e.g. 75776k -> 75776*1024).

Fixes: 2a9f3b7717 ("ipq40xx: fix up Linksys WHW01 board name, device definition")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2023-11-26 18:37:20 +01:00
Rani Hod
e29f4a3f70 ath79: add support for D-link DAP-1720 A1
D-Link DAP-1720 rev A1 is a mains-powered AC1750 Wi-Fi range extender,
manufactured by Alpha Networks [8WAPAC28.1A1G].
(in square brackets: PCB silkscreen markings)

Specifications:
* CPU (Qualcomm Atheros QCA9563-AL3A [U5]):
  775 MHz single core MIPS 74Kc;
* RAM (Winbond W9751G6KB-25J [U3]):
  64 MiB DDR2;
* ROM (Winbond W25Q128FV [U16]):
  16 MiB SPI NOR flash;
* Ethernet (AR8033-AL1A PHY [U1], no switch):
  1 GbE RJ45 port (no PHY LEDs);
* Wi-Fi
  * 2.4 GHz (Qualcomm Atheros QCA9563-AL3A [U5]):
    3x3 802.11n;
  * 5 GHz (Qualcomm Atheros QCA9880-BR4A [U9]):
    3x3 802.11ac Wave 1;
  * 3 foldable dual-band antennas (U.fl) [P1],[P2],[P3];
* GPIO LEDs:
  * RSSI low (red/green) [D2];
  * RSSI medium (green) [D3];
  * RSSI high (green) [D4];
  * status (red/green) [D5];
* GPIO buttons:
  * WPS [SW1], co-located with status LED;
  * reset [SW4], accessible via hole in the side;
* Serial/UART:
  Tx-Gnd-3v3-Rx [JP1], Tx is the square pin, 1.25mm pitch;
  125000-8-n-1 in U-boot, 115200-8-n-1 in kernel;
* Misc:
  * 12V VCC [JP2], fed from internal 12V/1A AC to DC converter;
  * on/off slide switch [SW2] (disconnects VCC mechanically);
  * unpopulated footprints for a Wi-Fi LED [D1];
  * unpopulated footprints for a 4-pin 3-position slide switch (SW3);

MAC addresses:
* Label = LAN;
* 2.4 GHz WiFi = LAN;
* 5 GHz WiFi = LAN+2;

Installation:
* `factory.bin` can be used to install OpenWrt from OEM firmware via the
  standard upgrade webpage at http://192.168.0.50/UpdateFirmware.html
* `recovery.bin` can be used to install OpenWrt (or revert to OEM
  firmware) from D-Link Web Recovery. To enter web recovery, keep reset
  button pressed and then power on the device. Reset button can be
  released when the red status LED is bright; it will then blink slowly.
  Set static IP to 192.168.0.10, navigate to http://192.168.0.50 and
  upload 'recovery.bin'. Note that in web recovery mode the device
  ignores ping and DHCP requests.

Note: 802.11s is not supported by the default `ath10k` driver and
firmware, but is supported by the non-CT driver and firmware variants.
The `-smallbuffers` driver variant is recommended due to RAM size.

Co-developed-by: Anthony Sepa <protectivedad@gmail.com>
Signed-off-by: Rani Hod <rani.hod@gmail.com>
2023-11-26 18:27:35 +01:00
Rosen Penev
b7f26c6392 ath79: ar: convert to mac-base
Replacement for deprecated mac-address-increment

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 21:34:18 -08:00
Rosen Penev
9783340af9 ath79: ar: convert to nvmem-layout
Will allow removing deprecated mac-address-increment.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 21:34:18 -08:00
Rosen Penev
de1d9da150 ath79: tp9343: convert to nvmem-layout
Allows getting rid of deprecated mac-address-increment.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 19:43:35 -08:00
Rosen Penev
ede82f35eb ath79: qcn: convert to nvmem-layout
Allows getting rid of deprecated mac-address-increment.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 19:43:32 -08:00
Rosen Penev
b2f1c6ed52 ath79: qca: remove mac-address-increment
nvmem-layout allows removal

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 17:14:04 -08:00
Rosen Penev
e816591e22 ath79: qca: convert to nvmem-layout
Allows replacing mac-address-increment with mac-base.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 17:14:04 -08:00
Rosen Penev
eea4dfaa7b ath79: mikrotik: fix dts warnings
property has invalid length

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 17:14:04 -08:00
Rosen Penev
3395184825
ramips: mt7621: nix mac-address-increment
nvmem-layout allows removal

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-26 01:30:32 +01:00
Rosen Penev
f4c33d098f
ramips: mt7621: convert to nvmem-layout
Allows replacing mac-address-increment with mac-base.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-26 01:30:32 +01:00
Rosen Penev
3c1c3f4685
ramips: mt7621: add interrupt-controller
Fixes dtc warning:

'#interrupt-cells' found, but node is not an interrupt provider

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-26 01:30:04 +01:00
Rosen Penev
458cb2cd6b
ramips: mt7620a: use mac-base
mac-address-increment is deprecated.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-26 00:15:58 +01:00
Rosen Penev
40feb97e56
ramips: mt7620a: convert to nvmem-layout
Allows using mac-base to replace mac-address-increment.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-26 00:15:58 +01:00
Rosen Penev
32c1ac8960
ramips: mt7620n: convert to nvmem-layout
nvmem-cells is deprecated. nvmem-layout allows using mac-base.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-26 00:15:55 +01:00
Rosen Penev
e8084a3c3b
ramips: mt7628: use mac-base
mac-address-increment is deprecated.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:58:44 +01:00
Rosen Penev
0a1d15642f
ramips: mt7628: use nvmem-layout
Will allow using mac-base.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:58:40 +01:00
Rosen Penev
3eb899fd36
mediatek: use mac-base
mac-address-increment is deprecated.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:45:26 +01:00
Rosen Penev
405bc5be13
mediatek: convert to nvmem-layout
Will allow removing mac-address-increment.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:45:26 +01:00
Rosen Penev
b976fa5d2b
ramips: rtxxxx: remove mac-address-increment
Deprecated and replaced upstream with mac-base.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:39:52 +01:00
Rosen Penev
5f479a4f34
ramips: rtxxxx: convert to nvmem-layout
Allows replacing mac-adress-increment.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:39:47 +01:00
Chukun Pan
07482d15af
mediatek: filogic: reorder alphabetically
Reorder scripts and image recipes to keep alphabetical order.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-11-25 23:16:35 +01:00
Chukun Pan
b74ae69596
mediatek: filogic: remove kmod-usb2 for GL-MT6000
The usb driver requires kmod-usb3, not kmod-usb2.
Remove the useless kmod-usb2 from default package.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-11-25 23:16:34 +01:00
Chukun Pan
1be6347b7d
mediatek: Cetron CT3003: fixes typo for spi properties
Same as commit 3674689, correct 'buswidth' to 'bus-width'.
Also move the nmbm properties outside the partition definition.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-11-25 23:16:34 +01:00
Rosen Penev
7e316bc53a
ipq40xx: remove mac-address-increment
nvmem-layout allows removal

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:14:54 +01:00
Rosen Penev
fe8dd23882
ipq40xx: convert to nvmem-layout
Allows replacing mac-address-increment with mac-base.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:14:54 +01:00
Rosen Penev
14467fd515
ipq40xx: fix dtc warnimg
I2C bus unit address format error, expected "62"

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 23:14:51 +01:00
Rosen Penev
eadf2ead4e
qualcommax: convert to nvmem-layout
nvmem-cells is deprecated

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 22:51:32 +01:00
Rosen Penev
10b7e2d0df
apm821xx: convert to nvmem-layout
nvmem-cells is deprecated.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 22:50:32 +01:00
Hauke Mehrtens
d99aed31a0 mediatek: filogic: Fix GPIOs for Zbtlink ZBT-Z8102AX
The PGIO configuration should be added for the ZBT-Z8102AX and not the ZBT-Z8103AX

Fixes: c8c2f52262 ("mediatek: add support for Zbtlink ZBT-Z8102AX")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-11-25 22:25:42 +01:00
Xiaobo Liu
5fbb1f09ca ramips: mt76x8 add support for RTC class/drivers
This commit adds support for RTC class/drivers to the mt76x8 target.

Signed-off-by: Xiaobo Liu <cppcoffee@gmail.com>
2023-11-25 18:16:46 +01:00
Darlan Pedro de Campos
2a0c9cc8cd ramips: add support for TP-Link EX220 v1
This device is very similar, if not identical, to the TP-Link AX23 v1
but is targeted at service providers and features a completely different
flash layout.

Hardware
--------

CPU:    MediaTek MT7621 DAT
RAM:    128MB DDR3 (integrated)
FLASH:  16MB SPI-NOR
WiFi:   MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax
SERIAL: 115200 8N1
        LEDs - (3V3 - GND - RX - TX) - ETH ports

Installation
------------

Flashing is only possible via a serial connection using the sysupgrade
image; the factory image must be signed. You can flash the sysupgrade
image directly through the U-Boot console, or preferably, by booting the
initramfs image and flashing with the sysupgrade command. Follow these
steps for sysupgrade flashing:

1. Establish a UART serial connection.
2. Set up a TFTP server at 192.168.0.2 and copy the initramfs image
   there.
3. Power on the device and press any key to interrupt normal boot.
4. Load the initramfs image using tftpboot.
5. Boot with bootm.
6. If you haven't done so already, back up all stock mtd partitions.
7. Copy the sysupgrade image to the router.
8. Flash OpenWrt through either LuCI or the sysupgrade command. Remember
   not to attempt saving settings.

Revert to stock firmware
------------------------

Flash stock firmware via OEM web-recovery mode. If you don't have access
to the stock firmware image, you will need to restore the firmware
partition backed up earlier.

Web-Recovery
------------

The router supports an HTTP recovery mode:

1. Turn off the router.
2. Press the reset button and power on the device.
3. When all LEDs start flashing, release reset and quickly press it
   again.

The interface is reachable at 192.168.0.1 and supports installation of
the OEM factory image. Note that flashing OpenWrt this way is not
possible, as mentioned above.

Signed-off-by: Darlan Pedro de Campos <darlanpedro@gmail.com>
2023-11-25 16:14:32 +01:00
Filip Milivojevic
288738c59d ramips: Add support for Cudy WR1300 v3
Specifications:
 - SoC: MediaTek MT7621AT
 - RAM: 128 MB (DDR3)
 - Flash: 16 MB (SPI NOR)
 - WiFi: MediaTek MT7603E, MediaTek MT7613BE
 - Switch: 1 WAN, 4 LAN (Gigabit)
 - Buttons: Reset, WPS
 - LEDs: System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS
 - Power: DC 12V 1A tip positive

Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.

Cudy WR1300 v3 differs from v2 only in swapped WiFi chip PCIe slots. Common
nodes are extracted to .dtsi and new v2 and v3 dts are created.

Cudy WR1300 v2 dts now contains ieee80211-freq-limit and has
eeprom_factory_8000 length fixed.

The same manufacturer's built OpenWRT image is provided for both v2 and v3
devices as a step in installing, but for proper WiFi functionality,
a separate build is required.

Recovery:
 - Loads only signed manufacture firmware due to bootloader RSA verification
 - serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
 - connect to any lan ethernet port
 - power on the device while holding the reset button
 - wait at least 8 seconds before releasing reset button for image to
   download
 - See http://www.cudytech.com/newsinfo/547425.html

Signed-off-by: Filip Milivojevic <zekica@gmail.com>
2023-11-25 15:48:41 +01:00
Valerio 'ftp21' Mancini
b5df398a36 mediatek: add Zyxel EX5601-T0 with uboot custom partition
The flash procedure is similar to the Xiaomi AX6000 router.

Load openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb from original Zyxel U-Boot:

tftpboot openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb
bootm 0x46000000
Load mtd-rw
insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1

Format ubi and create ubootenv partitions

ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
Copy openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb to /tmp and create recovery partition.
If your recovery image is larger than 10MiB, size the recovery partition accordingly to make it fit.

ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
ubiupdatevol /dev/ubi0_2  openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb
Copy preloader and uboot to /tmp and write them in the mtd

mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-preloader.bin bl2
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-bl31-uboot.fip fip
Now write the firmware:
sysupgrade -n  /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-squashfs-sysupgrade.itb

To create a correct BL2, I had to add a profile for 'spim:4k+256' as I could not find a way to value the variable 'NAND_TYPE'.

Features and fixes from hitech95 tree has been squashed, I'm attaching his commit message:

The Power LED was not working correctly and not reacting
 to the boot process and statuses.

The board has space (footprint) for an unpopulated Zigbee chip,
 while we dont know the device model having this chip populated
 we have to assure that the common dts doesnt enable
 interfaces that share pins with such device.

In this instance the PCIe and the uart1 and uart2 are disabled.
Some of the control PCIE pins seems to be used for the Zigbee chip,
 UART1 seems to be used as a flash port while UART2 should be the
 main comunication interface of Zigbee chip.

The Zigbee chip should be a EFR32MG21. But the pins used for UART
 seems to be not on standard PINS used by other adapters.
 So it cannot run firmwares shared on the web.
 But it should be possible to build a custom firmware with
 the corrtect pinmux.

This commit also contains the following squashed commit from hitech95
 - mediatek: fix sysupgrade for Zyxel EX7601-T0 ubootmod

Changes and fixes added in common board:
 - added aliases for boot status leds.
 - added aliases for the mac-label-device.
 - added pin claims for core features (MDIO and UART 0)
 - added default LEDs configuration (01_leds)
 - added default network configuration (02_network)
 - added missing kmod-usb3 module for USB3
 - fixed LED names
 - fixed reset pin for SLIC chip
 - removed unused pinmux configurations and devices
 - fix LAN (switch) port numbering
 - using nvmem cells for wifi eeprom, dropping deprecated "mediatek,mtd-eeprom"
 - proper factory partition and mac address handling
 - cleaned up spi_nand sections and partition

Changes and fixxes added in stock layout:
 - added NMBM, if u-boot has it, the kernel must be informed.

Co-authored-by: Nicolò Veronese <nicveronese@gmail.com>
Co-developed-by: Nicolò Veronese <nicveronese@gmail.com>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
2023-11-25 14:51:21 +01:00
Daniel Golle
1b70025ad1 mediatek: remove DTS property added by mistake
Remove bogus 'phy-handle = <&phy0>;', an undefined reference.

Fixes: c8c2f52262 ("mediatek: add support for Zbtlink ZBT-Z8102AX")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-25 03:22:47 +00:00
Mikhail Zhilkin
1b091311aa ramips: add support for Sercomm CPJ routers
This commit adds support for following wireless routers:
 - Rostelecom RT-FL-1 (Serсomm RT-FL-1)
 - Rostelecom S1010 (Serсomm S1010.RT)

The devices are almost identical and the only difference is one bit in the
factory image PID (thanks to Maximilian Weinmann <x1@disroot.org>
(@MaxS0niX) for the info and idea to make one PR for two devices at once).

Devices specification
---------------------
   SoC:          MediaTek MT7620A, MIPS
   RAM:          64 MB
   Flash:        16 MB SPI NOR
   Wireless 2.4: MT7620 (b/g/n, 2x2)
   Wireless 5:   MT7612EN (a/n/ac, 2x2)
   Ethernet:     5xFE (WAN, LAN1-4)
   BootLoader:   U-Boot
   Buttons:      2 (wps, reset)
   LEDs:         1 amber and 1 green status GPIO leds
                 5 green ethernet GPIO leds
                 1 green GPIO 2.4 GHz WLAN led
                 1 green PHY 5 GHz WLAN led
                 1 green unmanaged power led
   USB ports:    No
   Power:        12 VDC, 1 A
   Connector:    Barrel

OEM easy installation
---------------------
1. Remove all dots from the factory image filename (except the dot
   before file extension)
2. Upload and update the firmware via the original web interface
3. Wait until green status led stops blinking (can take several minutes)
4. Login to OpenWrt initramsfs. It's recommended to make a backup of the
   mtd partitions at this point.
4. Perform sysupgrade using the following command (or use Luci):
   sysupgrade -n sysupgrade.bin
5. Wait until green status les stops blinking (can take several minutes)
6. Mission acomplished

Return to Stock
---------------
Option 1. Restore firmware Slot1 from a backup (firmware2.bin):
   cd /tmp
   mtd -e Firmware2 write firmware2.bin Firmware2
   printf 1 | dd bs=1 seek=$((0x18007)) count=1 of=/dev/mtdblock2
   reboot

Option 2. Decrypt, ungzip and split stock firmware image into the parts,
take Slot1 parts (kernel2.bin, rootfs2.bin) and write them:
   cd /tmp
   mtd -e Kernel2 write kernel2.bin Kernel2
   mtd -e RootFS2 write rootfs2.bin RootFS2
   printf 1 | dd bs=1 seek=$((0x18007)) count=1 of=/dev/mtdblock2
   reboot
More about stock firmware decryption:
Link: https://github.com/Psychotropos/sercomm_fwutils/

Debricking
----------
Use sercomm-recovery tool. You can use "ALL" mtd partition backup as a
recovery image.
Link: https://github.com/danitool/sercomm-recovery

MAC addresses
-------------
+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| label   | 48:3e:xx:xx:xx:1e | label     |
| LAN     | 48:3e:xx:xx:xx:1e | label     |
| WAN     | 48:3e:xx:xx:xx:28 | label+10  |
| WLAN 2g | 48:3e:xx:xx:xx:20 | label+2   |
| WLAN 5g | 48:3e:xx:xx:xx:24 | label+6   |
+---------+-------------------+-----------+

Co-authored-by: Vadzim Vabishchevich <bestmc2009@gmail.com>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-11-25 01:11:18 +01:00
Mikhail Zhilkin
25bab2b8bc ramips: mt7620: drop unnecessary trailing tabs
Let's tidy up a bit (drop unnecessary trailing tabs).

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-11-25 01:11:18 +01:00
Mikhail Zhilkin
e900c45211 ramips: sercomm.mk: make common recipe to set a bit in pid
This commit makes a common recipe to set bit in Sercomm factory pid since
this is necessary for several devices (WiFire S1500.nbn, Rostelecom
RT-FL-1) at different offsets.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-11-25 01:11:18 +01:00
Robert Marko
5dae4a6aba ipq40xx: refresh patches
CI reported that ipq40xx needed a refresh, so lets refresh it.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-11-25 00:12:01 +01:00
Daniel Golle
c8c2f52262 mediatek: add support for Zbtlink ZBT-Z8102AX
Specifications:
SoC: MediaTek MT7981B
RAM: 1024MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit)
USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND

Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware

B. Through TFTP
Standard installation via UART:

1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.

Based on patch adding support for similar Zbtlink ZBT-Z8103AX device by
Ian Ishmael C. Oderon.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-24 21:28:35 +00:00
Christian Marangi
6f5c301eab
generic: 6.1: backport upstream Aquantia PHY firmware loader patches
Backport merged upstream patch that adds support for firmware loader
from NVMEM or attached filesystem for Aquantia PHYs.

Refresh all kernel patches affected by this change.

Also update the path for aquantia .ko that got moved to dedicated
directory upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-11-24 16:46:50 +01:00
Rosen Penev
d1b5981038
realtek: convert to nvmem-layout
nvmem-cells is deprecated.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-24 16:37:02 +01:00
John Audia
df167450a5 kernel: bump 5.15 to 5.15.139
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.139

Removed upstreamed:
	backport-5.15/830-v6.6-2-leds-turris-omnia-Drop-unnecessary-mutex-locking.patch[1]
	backport-5.15/830-v6.7-1-leds-turris-omnia-Do-not-use-SMBUS-calls.patch[2]
	x86/patches-5.15/120-hwrng-geode-fix-accessing-registers.patch[3]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.139&id=aec3706971b332af8321b2beccba981b8061489a
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.139&id=893eedf596dd81c7a7f0cd80b345956ae000eab9
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.139&id=a5c83c8043d70b9a28d1bd78a2dbbab340f43889

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-11-23 22:55:55 +01:00
John Audia
2b75f108fb kernel: bump 6.1 to 6.1.63
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.63

Removed upstreamed:
	generic/backport-6.1/815-v6.6-2-leds-turris-omnia-Drop-unnecessary-mutex-locking.patch
	generic/backport-6.1/815-v6.7-1-leds-turris-omnia-Do-not-use-SMBUS-calls.patch
	ixp4xx/patches-6.1/0007-watchdog-ixp4xx-Make-sure-restart-always-works.patch

Manually rebased:
	bcm27xx/patches-6.1/950-0606-hwrng-bcm2835-sleep-more-intelligently.patch

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.63&id=7d0e60e4ff840e97fb18afb2a7344442c10a6fdf
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.63&id=63cdeb20ee3bfef820b045b8d3b8395f9f815a74
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.63&id=8803da01fe1b4ca3d37745283f7e73c6c2558c0c

Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-11-23 22:51:52 +01:00
Daniel Linjama
a39a49e323 ath79: add support for D-Link COVR-P2500 A1
Specifications:
* QCA9563, 16 MiB flash, 128 MiB RAM, 2T2R 802.11n
* QCA9886 2T2R 801.11ac Wave 2
* QCA7550 Homeplug AV2 1300
* AR8337, 3 Gigabit ports (1, 2: LAN; 3: WAN)

To make use of PLC functionality, firmware needs to be
provided via plchost (QCA7550 comes without SPI NOR),
patched with the Network Password and MAC.

Flashing via OEM Web Interface
* Flash 'factory.bin' using web-interface
* Wait until firmware succesfully installed and device booted
* Hold down reset button to reset factory defaults (~10 seconds)

Flashing via Recovery Web Interface:
* Hold down reset button during power-on (~10 seconds)
* Recovery Web UI is at 192.168.0.50, no DHCP.
* Flash 'recovery.bin' with
  scripts/flashing/dlink_recovery_upload.py
  (Recovery Web UI does not work with modern OSes)

Return to stock
* Hold down reset button during power-on (~10 seconds)
* Recovery Web UI is at 192.168.0.50, no DHCP.
* Flash unencrypted stock firmware with
  scripts/flashing/dlink_recovery_upload.py
  (Recovery Web UI does not work with modern OSes)

Co-developed-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Signed-off-by: Daniel Linjama <daniel@dev.linjama.com>
2023-11-23 00:26:28 +01:00
Rosen Penev
944d3526a3
mvebu: remove mac-address-increment
It's deprecated.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-22 19:58:22 +01:00
Rani Hod
aaeb379023 mediatek: fiilogic: device tree switch@1f fix
Quite a few `fiilogic` devices use the `mt7531` switch.
Some of them have a DT node that looks like:
```
switch: switch@0 {
	compatible = "mediatek,mt7531";
	reg = <31>;
...
};
```
This commit changes the DT node name to `switch@1f`.

Signed-off-by: Rani Hod <rani.hod@gmail.com>
2023-11-22 19:42:23 +02:00