This patch defines the two switch LED to bring them under user control.
Fixes: 158a5af801 ("ramips: improve YunCore AX820 LEDs")
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
[rmilecki: leave "label"s in place]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 7bee10a7d2)
Specifications:
- SoC: Qualcomm Atheros QCA9557-AT4A
- RAM: 2x 128MB Nanya NT5TU64M16HG
- FLASH: 64MB - SPANSION FL512SAIFG1
- LAN: Atheros AR8035-A (RGMII GbE with PoE+ IN)
- WLAN2: Qualcomm Atheros QCA9557 2x2 2T2R
- WLAN5: Qualcomm Atheros QCA9882-BR4A 2x2 2T2R
- SERIAL: UART pins at J10 (115200 8n1)
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
- LEDs: Power (Green/Amber)
WiFi 5 (Green)
WiFi 2 (Green)
- BTN: Reset
Installation:
1. Download the OpenWrt initramfs-image.
Place it into a TFTP server root directory and rename it to 1D01A8C0.img
Configure the TFTP server to listen at 192.168.1.66/24.
2. Connect the TFTP server to the access point.
3. Connect to the serial console of the access point.
Attach power and interrupt the boot procedure when prompted.
Credentials are admin / new2day
4. Configure U-Boot for booting OpenWrt from ram and flash:
$ setenv boot_openwrt 'setenv bootargs; bootm 0xa1280000'
$ setenv ramboot_openwrt 'setenv serverip 192.168.1.66;
tftpboot 0x89000000 1D01A8C0.img; bootm'
$ setenv bootcmd 'run boot_openwrt'
$ saveenv
5. Load OpenWrt into memory:
$ run ramboot_openwrt
6. Transfer the OpenWrt sysupgrade image to the device.
Write the image to flash using sysupgrade:
$ sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: Albin Hellström <albin.hellstrom@gmail.com>
[rename vendor - minor style fixes - update commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit f8c87aa2d2)
Refresh all patches on top of kernel 5.10.138.
The following patches were applied upstream:
bcm27xx/patches-5.10/950-0311-drm-vc4-Adopt-the-dma-configuration-from-the-HVS-or-.patch
bcm27xx/patches-5.10/950-0317-vc4_hdmi-Remove-firmware-logic-for-MAI-threshold-set.patch
bcm27xx/patches-5.10/950-0346-drm-vc4-A-present-but-empty-dmas-disables-audio.patch
bcm27xx/patches-5.10/950-0354-drm-vc4-Add-the-2711-HVS-as-a-suitable-DMA-node.patch
bcm27xx/patches-5.10/950-0413-drm-vc4-hdmi-Don-t-access-the-connector-state-in-res.patch
bcm27xx/patches-5.10/950-0505-vc4-drm-Avoid-full-hdmi-audio-fifo-writes.patch
bcm27xx/patches-5.10/950-0512-vc4-drm-vc4_plane-Remove-subpixel-positioning-check.patch
bcm27xx/patches-5.10/950-0560-drm-vc4-drv-Remove-the-DSI-pointer-in-vc4_drv.patch
bcm27xx/patches-5.10/950-0561-drm-vc4-dsi-Use-snprintf-for-the-PHY-clocks-instead-.patch
bcm27xx/patches-5.10/950-0562-drm-vc4-dsi-Introduce-a-variant-structure.patch
bcm27xx/patches-5.10/950-0565-drm-vc4-Correct-pixel-order-for-DSI0.patch
bcm27xx/patches-5.10/950-0566-drm-vc4-Register-dsi0-as-the-correct-vc4-encoder-typ.patch
bcm27xx/patches-5.10/950-0567-drm-vc4-Fix-dsi0-interrupt-support.patch
bcm27xx/patches-5.10/950-0568-drm-vc4-Add-correct-stop-condition-to-vc4_dsi_encode.patch
bcm27xx/patches-5.10/950-0647-drm-vc4-Fix-timings-for-interlaced-modes.patch
bcm27xx/patches-5.10/950-0695-drm-vc4-Fix-margin-calculations-for-the-right-bottom.patch
Upstream sets the pixel clock to 340MHz now, do not set it to 600MHz any more.
bcm27xx/patches-5.10/950-0576-drm-vc4-hdmi-Raise-the-maximum-clock-rate.patch
Fixes: 89956c6532 ("kernel: bump 5.10 to 5.10.138")
Fixes: 4209c33ae2 ("kernel: bump 5.10 to 5.10.137")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit 5a81e00063 as it was
backported upstream in commit a1e238690916 ("arm64: dts: mt7622: fix
BPI-R64 WPS button").
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Removed following upstreamed patch:
* bcm53xx: 081-next-ARM_dts_BCM53015-add-mr26.patch
All other patches automagically rebased.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit d1163fd13f)
35fec487e3 fixed opkg usage,
but when using buildroot we were still defaulting to
ip(6)tables-legacy
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
(cherry picked from commit 0c8d7e34ab)
Change switch port labels to ethblack & ethblue.
Change lan1 & lan2 LEDs to ethblack_act & ethblue_act and fix GPIO pins.
Add the external phy with ethyellow label on the GB-PC2 devicetree.
Do not claim rgmii2 as gpio, it's used for ethernet with rgmii2 function.
Enable ICPlus PHY driver for IP1001 which GB-PC2 has got.
Update interface name and change netdev function.
Enable lzma compression to make up for the increased size of the kernel.
Make spi flash bindings on par with mainline Linux to fix read errors.
Tested on GB-PC2 by Petr.
Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit 4807bd6a00)
WPA3 enterprise requires group_mgmt_cipher=BIP-GMAC-256 and if 802.11r is
active also wpa_key_mgmt FT-EAP-SHA384. This commit also requires
corresponding changes in netifd.
Signed-off-by: Joerg Werner <schreibubi@gmail.com>
(cherry picked from commit 9fbb76c047)
In the SDK the folder $(LINUX_DIR)/user_headers/include does not exist,
but it more or less contains the same content as
$(LINUX_DIR)/include/uapi which also exists in the SDK.
Since iproute2 commit 1d819dcc741e ("configure: fix parsing issue on
include_dir option") it checks if this folder exists and aborts the
build if it does not exists.
https://git.kernel.org/pub/scm/network/iproute2/iproute2.git/commit/?id=1d819dcc741e25958190e31f8186c940713fa0a8
With this commit the KERNEL_INCLUDE variable points to a valid folder
with the kernel include headers. I am not sure if they are actually
needed because the build worked before even with an invalid path.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 60738feded)
gcc 10 with -O2 reports following:
In function ‘strncpy’,
inlined from ‘rpc_sys_packagelist’ at /opt/devel/openwrt/c-projects/rpcd/sys.c:244:4:
/usr/include/x86_64-linux-gnu/bits/string_fortified.h:106:10: error: ‘__builtin_strncpy’ specified bound 128 equals destination size [-Werror=stringop-truncation]
106 | return __builtin___strncpy_chk (__dest, __src, __len, __bos (__dest));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In function ‘strncpy’,
inlined from ‘rpc_sys_packagelist’ at /opt/devel/openwrt/c-projects/rpcd/sys.c:227:4:
/usr/include/x86_64-linux-gnu/bits/string_fortified.h:106:10: error: ‘__builtin_strncpy’ specified bound 128 equals destination size [-Werror=stringop-truncation]
106 | return __builtin___strncpy_chk (__dest, __src, __len, __bos (__dest));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Since it is not possible to avoid truncation by strncpy, it is necessary
to make sure the result of strncpy is properly NUL-terminated and the
NUL must be inserted explicitly, after strncpy has returned.
References: #10442
Reported-by: Alexey Smirnov <s.alexey@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 34ddd2e545)
e3395cd ucode: initialize search path before VM init
8cb3f85 ucode: initialize default library search path
188dea2 utils: accept '?' as path terminator in uh_path_match()
c5eac5d file: support using dynamic script handlers as error pages
290ff88 relay: trigger close if in header read state with pending data
f9db538 ucode: ignore exit exceptions
8ba0b64 cmake: use variables and find_library for dependency
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(backported from commit 4ee77cfcfa)
bcdd2cb examples: add module search path initialization and freeing
ee1946f ubus: fix GCC strncpy() truncation warning
131d99c lib: introduce three new functions call(), loadstring() and loadfile()
8e8dae0 lib: introduce helper function for indenting error messages
476f02b lib: simplify include_path()
d84b53a source: avoid null pointer access in uc_source_runpath_set()
c43a54f types: gracefully handle unpatched upvalues in ucv_free()
e2fb11a README.md: document gc() function
b41cb2d main: introduce -g flag to allow enabling periodic gc from cli
85d7885 lib: implement gc()
47528f0 vm: support automatic periodic GC runs
381cc75 types: treat vm->exports as GC roots
fcc49e6 compiler: add import statement support for dynamic extensions
c9442f1 vm: introduce new I_DYNLOAD opcode
b6fd8a2 lib: internally expose new uc_require_library() helper
a486adc vm: don't treat offset 0 special for exceptions
41ccd19 compiler: don't treat offset 0 special at syntax errors
b4a3f68 compiler: improve formatting of nested syntax error messages
5d5dadc program: remove now unused uc_program_export_lookup()
304995b compiler: rework export index allocation
506cc37 compiler: fix deriving module path from source runpath
54b7fac compiler: enforce stricter module compilation rules
d62e372 vm: don't initialize upvalues for module functions
b856602 program: add serialization and deserialization for module function flag
d7d1bde compiler: add a flag denoting module functions
156d584 treewide: unexport libucode internal functions
10e056d compiler: add support for import/export statements
862e49d compiler: resolve predeclared upvalues
78dfb08 compiler: require a name in function declarations
afd78c1 compiler: fix reported source position in inc/dec operator error
e1c3db0 tests: run_tests.sh: substitute dynamic test directory path in output
3c168b5 vm, cli: move search path into global configuration structure
d85bc71 vm: introduce import and export opcodes
365782e vm: honor constant flag of objects and arrays
6becc64 vm: transparently resolve upvalue references
3418967 vm: gracefully handle unresolved upvalues
50cf572 program: add function to globally lookup exported name
c441f65 program: add infrastructure to handle multiple sources per program
2322468 program: fix reporting source position of first instruction
9c9a9ec program: fix en/decoding debuginfo upvalue slots in precompiled bytecode
41114a0 source: add tracking of exported symbols
70ae304 lib: honor constant flag of arrays
3c104f5 types: resolve upvalue references on stringification
3a6f9cb types: add ability to mark array and object values as constant
b738f3a lexer: recognize module related keywords
03c8e4b lexer: rewrite token scanner
fd433aa lexer: fix parsing with disabled block left stripping
557577a rtnl: fix parsing/creation of IFLA_AF_SPEC RTA for the AF_BRIDGE family
35c6b73 compiler: fix stack mismatch on continue statements nested in switches
f673096 uloop: end uloop on exceptions in managed code
2e5426c ubus: end uloop on exceptions in managed code
c024270 rtnl: expose IFLA_STATS64 contents
d3c58c0 rtnl: expose ifinfomsg.ifi_change member
c4dde50 rtnl: update NETLINK_GET_STRICT_CHK socket flag with every request
7ef0d02 nl80211: fix NL80211_SURVEY_INFO_NOISE datatype
9a2e592 compiler: fix stack mismatch on nonmatching switch statements with locals
03c8ca5 nl80211: recognize further NL80211_STA_INFO_* NLAs
a1ed566 struct: add optional offset argument to `unpack()`
230e595 rtnl: fix segmentation fault on parsing linkinfo RTA without data
523566d rtnl: zero request message headers
56be30d rtnl: fix premature netlink reply receive abort
1347440 rtnl: avoid stray "netlink: %d bytes leftover after parsing attributes."
44b0a3b struct: fix packing `*` format after other repeated formats
Also package uloop binding module which has been introduced by a previous
ucode update and introduce a host build with the basic set of modules.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 3446d32616)
Musl libc does not support the non-POSIX "%F" format for strptime() so
replace all occurrences of it with an equivalent "%Y-%m-%d" format.
Fixes: #10419
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(backported from commit e6e4f97999)
a4484d4 fw4: support automatic includes
ca7e3a1 fw4: honour enabled option of include sections
5a02f74 tests: add missing fs.stat) mock data for `nf_conntrack_dummy`
111a7f7 fw4: don't inherit zone family from ct helpers
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit fe86b2ffaa)
Add missing scaling_available_frequencies sysfs entry for dedicated
cpufreq driver.
This sysfs entry is not standard and each cpufreq driver needs to
provide it and declare it in the cpufreq driver struct attr.
Fixes: 5dbbefcbcc ("ipq806x: introduce dedicated krait cpufreq")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
[ fix conflict by dropping 5.15 patch not present in openwrt-22.03 ]
(cherry picked from commit d6994c53cd)
It is common for 802.11ax NICs to support more than just AP mode, which
results in there being a distinct set of HE capabilities for each mode. As
(bad) luck would have it, iw prints out info for each HE mode in sequential
order according to `enum nl80211_iftype`, and AP mode isn't always first.
As a result, the wrong set of HE capabilities can be parsed if an AP NIC
supports station (managed) mode or any other mode preceding AP mode, since
only the first set of HE capabilities printed by iw is parsed from awk's
output.
This has a noticeable impact on beamforming for example, since managed mode
usually doesn't have beamformer capabilities enabled, while AP mode does.
Hostapd won't be set up with the configs to enable beamformer capabilities
in this scenario, causing hostapd to disable beamforming to HE stations
even when it's supported by the AP.
Always parse the correct set of HE capabilities for AP mode to fix this.
This is achieved by trimming all of iw's output prior to the AP mode
capabilities, which ensures that the first set of HE capabilities are
always for AP mode.
Signed-off-by: Sultan Alsawaf <sultan@kerneltoast.com>
(cherry picked from commit f338f76a66)
This commit resolves#10062. Adds decryption of the Arcadyan WG4xx223
configuration partition (board_data)to get base MAC address from it.
As a result, after this change the hack with saving MAC addressees to
u-boot-env before installation of OpenWrt is no longer necessary.
This is necessary for the following devices:
- Beeline Smartbox Flash (Arcadyan WG443223)
- MTS WG430223 (Arcadyan WG430223)
Example:
+----------------+-------------------+------------------------+
| | MTS WG430223 | Beeline Smartbox Flash |
+----------------+-------------------+------------------------+
| base mac (mtd) | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:06 |
| label | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:09 |
| LAN | A4:xx:xx:51:xx:F6 | 30:xx:xx:51:xx:09 |
| WAN | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:06 |
| WLAN_2g | A4:xx:xx:51:xx:F5 | 30:xx:xx:51:xx:07 |
| WLAN_5g | A6:xx:xx:21:xx:F5 | 32:xx:xx:41:xx:07 |
+----------------+-------------------+------------------------+
Collected statistic shows that the 2-4th bits of the 7th byte of the
WLAN_5g MAC are the constant (see #10062 for more details):
- Beeline Smartbox Flash - 100
- MTS WG430223 - 010
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit a6b0d08060)
Some Arcadyan devices (e.g. MTS WG430223) keep their config in encrypted
mtd. This adds mtd_get_mac_encrypted_arcadyan() function to get the MAC
address from the encrypted partition. Function uses uencrypt utility for
decryption (and openssl if the uencrypt wasn't found).
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 12c971bc26)
This adds a simple AES-128-CBC encryption/decryption program using
either wolfSSL or OpenSSL as backend to decrypt Arcadyan WG4xx223
configuration partitions. The ipk size is 3,355 bytes.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit bc43ad88ed)
This commit:
1. Renames beeline-trx recipe in mt7621.mk to arcadyan-trx. The recipe
is necessary for:
- MTS WG430223 (Arcadyan WG430223)
- Beeline Smartbox Flash (Arcadyan WG443223)
2. Allows specify custom trx magic which is different for the routers
mentined above.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 109c503bee)
[fix merging conflict in mt7621.mk]
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
This commit moves common properties for the boards below to a new dtsi:
Beeline Smartbox Flash (Arcadyan WG443223)
MTS WG430223 (Arcadyan WG430223)
The boards are almost the same. Here is the differences:
+------+----------+----------+
| | WG430223 | WG443223 |
+------+----------+----------+
| RAM | 128 | 256 |
+------+----------+----------+
| USB | - | 1x3.0 |
+------+----------+----------+
| LEDS | RG | RGB |
+------+----------+----------+
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 5b59137a16)
MTS WG430223 is a wireless AC1300 (WiFi 5) router manufactured by
Arcadyan company. It's very similar to Beeline Smartbox Flash (Arcadyan
WG443223).
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB
Flash: 128 MiB (Winbond W29N01HV)
Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2
Wireless 5 GHz (MT7615DN): a/n/ac, 2x2
Ethernet: 3xGbE (WAN, LAN1, LAN2)
USB ports: No
Button: 1 (Reset/WPS)
LEDs: 2 (Red, Green)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2)
OEM: Arcadyan WG430223
Installation
------------
1. Login to the router web interface (superadmin:serial number)
2. Navigate to Administration -> Miscellaneous -> Access control lists &
enable telnet & enable "Remote control from any IP address"
3. Connect to the router using telnet (default admin:admin)
4. Place *factory.trx on any web server (192.168.1.2 in this example)
5. Connect to the router using telnet shell (no password required)
6. Save MAC adresses to U-Boot environment:
uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \
awk '{print $5}')
uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \
awk '{print $5}')
uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \
awk '{print $5}')
uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \
awk '{print $5}')
7. Ensure that MACs were saved correctly:
uboot_env --get --name eth2macaddr
uboot_env --get --name eth3macaddr
uboot_env --get --name ra0macaddr
uboot_env --get --name rax0macaddr
8. Download and write the OpenWrt images:
cd /tmp
wget http://192.168.1.2/factory.trx
mtd_write erase /dev/mtd4
mtd_write write factory.trx /dev/mtd4
9. Set 1st boot partition and reboot:
uboot_env --set --name bootpartition --value 0
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv bootpartition 1
reboot
2. Optional step. Upgrade the stock firmware with any version to
overwrite the OpenWrt in Slot 1.
MAC addresses
-------------
+-----------+-------------------+----------------+
| Interface | MAC | Source |
+-----------+-------------------+----------------+
| label | A4:xx:xx:51:xx:F4 | No MACs was |
| LAN | A4:xx:xx:51:xx:F6 | found on Flash |
| WAN | A4:xx:xx:51:xx:F4 | [1] |
| WLAN_2g | A4:xx:xx:51:xx:F5 | |
| WLAN_5g | A6:xx:xx:21:xx:F5 | |
+-----------+-------------------+----------------+
[1]:
a. Label wasb't found neither in factory nor in other places.
b. MAC addresses are stored in encrypted partition "glbcfg". Encryption
key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack
with saving of the MACs to u-boot-env during the installation was
applied.
c. Default Ralink ethernet MAC address (00:0C:43:28:80:A0) was found in
"Factory" 0xfff0. It's the same for all MTS WG430223 devices. OEM
firmware also uses this MAC when initialazes ethernet driver. In
OpenWrt we use it only as internal GMAC (eth0), all other MACs are
unique. Therefore, there is no any barriers to the operation of several
MTS WG430223 devices even within the same broadcast domain.
Stock firmware image format
---------------------------
The same as Beeline Smartbox Flash but with another trx magic
+--------------+---------------+----------------------------------------+
| Offset | | Description |
+==============+===============+========================================+
| 0x0 | 31 52 48 53 | TRX magic "1RHS" |
+--------------+---------------+----------------------------------------+
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 498c15376b)
Specifications:
- Device: ASUS RT-AX53U
- SoC: MT7621AT
- Flash: 128MB
- RAM: 256MB
- Switch: 1 WAN, 3 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- Ports: USB 3.0
- LEDs: 1x POWER (blue, configurable)
3x LAN (blue, configurable)
1x WAN (blue, configurable)
1x USB (blue, not configurable)
1x 2.4G (blue, not configurable)
1x 5G (blue, not configurable)
Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.1.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
Select "2. Upgrade firmware"
Press enter when show "Run firmware after upgrading? (Y/n):"
Select 0 for TFTP method
Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.2
Input IP netmask: 255.255.255.0
Input file name: openwrt-ramips-mt7621-asus_rt-ax53u-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"
Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com>
(replaced led label, added key-* prefix to buttons, added note about
BBT)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 8c00fd9b45)
It backports this patch series, which is currently on review:
https://lore.kernel.org/linux-leds/20220704105955.15474-1-kabel@kernel.org/T/#rb89a4ca5a836f17bdcc53d65549e0b1779bb6a18
It allows being able to configure LEDs in userspace.
This fixes issue described in Turris Build repository
https://gitlab.nic.cz/turris/os/build/-/issues/354
It happens in OpenWrt as well.
- Before
```
root@turris:/# ls /sys/class/leds/
ath10k-phy0 ath9k-phy1 mmc0::
```
-After
```
root@turris:/# ls /sys/class/leds/
ath10k-phy0 rgb:indicator-2 rgb:lan-3 rgb:wlan-1
ath9k-phy1 rgb:lan-0 rgb:lan-4 rgb:wlan-2
mmc0:: rgb:lan-1 rgb:power rgb:wlan-3
rgb:indicator-1 rgb:lan-2 rgb:wan
```
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit 049368b936)
In subtarget p2020, there wasn't enabled nand support, and because of
that there weren't available tools from mtd-utils package, which has
utilities for NAND flash memory even though reference board, which
is the only currently supported device in p2020 subtarget has NAND [1].
All subtargets in mpc85xx has already enabled nand support, let's do it
globally.
[1] https://www.nxp.com/design/qoriq-developer-resources/p2020-reference-design-board:P2020RDB
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit 6006f73383)
Add support for LEDs of the CZ.NIC Turris Omnia using the upstream
driver.
There is no generic way to control the LEDs in UCI manner, however
the kernel module is the first step to actually use the RGB LEDs in
custom logic.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
(removed DMARC notice, added driver to Turris Omnia, moved module
recipe to target/linux/mvebu/modules.mk)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit f8fa38c13f)
Reviewed-by: Robert Marko <robimarko@gmail.com>
This adds the following changes:
71326f1f2f nptl: Fix pthread_cancel cancelhandling atomic operations
3e0a91b79b scripts: Add glibcelf.py module
f0c71b34f9 Default to --with-default-link=no (bug 25812)
ca0faa140f misc: Fix rare fortify crash on wchar funcs. [BZ 29030]
0d477e92c4 INSTALL: Rephrase -with-default-link documentation
bc56ab1f4a dlfcn: Do not use rtld_active () to determine ld.so state (bug 29078)
83cc145830 scripts/glibcelf.py: Mark as UNSUPPORTED on Python 3.5 and earlier
16245986fb x86-64: Optimize load of all bits set into ZMM register [BZ #28252]
b5a44a6a47 x86: Modify ENTRY in sysdep.h so that p2align can be specified
5ec3416853 x86: Optimize memcmp-evex-movbe.S for frontend behavior and size
6d18a93dbb x86: Optimize memset-vec-unaligned-erms.S
baf3ece634 x86: Replace sse2 instructions with avx in memcmp-evex-movbe.S
f35ad30da4 x86-64: Improve EVEX strcmp with masked load
a182bb7a39 x86-64: Remove Prefer_AVX2_STRCMP
2e64237a87 x86-64: Replace movzx with movzbl
a7392db2ff x86: Optimize memmove-vec-unaligned-erms.S
cecbac5212 x86: Double size of ERMS rep_movsb_threshold in dl-cacheinfo.h
7cb126e7e7 x86: Shrink memcmp-sse4.S code size
4bbd0f866a x86-64: Use notl in EVEX strcmp [BZ #28646]
f3a99b2216 x86: Don't set Prefer_No_AVX512 for processors with AVX512 and AVX-VNNI
c796418d00 x86: Optimize L(less_vec) case in memcmp-evex-movbe.S
9681691402 linux: Fix missing internal 64 bit time_t stat usage
55640ed3fd i386: Regenerate ulps
88a8637cb4 linux: Fix fchmodat with AT_SYMLINK_NOFOLLOW for 64 bit time_t (BZ#29097)
c66c92181d posix/glob.c: update from gnulib
bc6fba3c80 Add PF_MCTP, AF_MCTP from Linux 5.15 to bits/socket.h
fd5dbfd1cd Update kernel version to 5.15 in tst-mman-consts.py
5146b73d72 Add ARPHRD_CAN, ARPHRD_MCTP to net/if_arp.h
6af165658d Update syscall lists for Linux 5.17
81181ba5d9 Update kernel version to 5.16 in tst-mman-consts.py
0499c3a95f Update kernel version to 5.17 in tst-mman-consts.py
f858bc3093 Add SOL_MPTCP, SOL_MCTP from Linux 5.16 to bits/socket.h
c108e87026 aarch64: Add HWCAP2_ECV from Linux 5.16
97cb8227b8 Add HWCAP2_AFP, HWCAP2_RPRES from Linux 5.17 to AArch64 bits/hwcap.h
31af92b9c8 manual: Clarify that abbreviations of long options are allowed
0d5b36c8cc x86: Optimize strcmp-avx2.S
c41a66767d x86: Optimize strcmp-evex.S
d299032743 x86-64: Fix strcmp-avx2.S
53ddafe917 x86-64: Fix strcmp-evex.S
ea19c490a3 x86: Improve vec generation in memset-vec-unaligned-erms.S
190ea5f7e4 x86: Remove SSSE3 instruction for broadcast in memset.S (SSE2 Only)
5cb6329652 x86-64: Optimize bzero
70509f9b48 x86: Set .text section in memset-vec-unaligned-erms
5373c90f2e x86: Fix bug in strncmp-evex and strncmp-avx2 [BZ #28895]
e123f08ad5 x86: Fix fallback for wcsncmp_avx2 in strcmp-avx2.S [BZ #28896]
e4a2fb76ef manual: Document the dlinfo function
91c2e6c3db dlfcn: Implement the RTLD_DI_PHDR request type for dlinfo
b72bbba236 fortify: Ensure that __glibc_fortify condition is a constant [BZ #29141]
8de6e4a199 x86: Improve L to support L(XXX_SYMBOL (YYY, ZZZ))
6cba46c858 x86_64/multiarch: Sort sysdep_routines and put one entry per line
37f373e334 x86-64: Remove bzero weak alias in SS2 memset
dd457606ca x86_64: Remove bcopy optimizations
3c55c20756 x86: Code cleanup in strchr-avx2 and comment justifying branch
dd6d3a0bbc x86: Code cleanup in strchr-evex and comment justifying branch
0ae1006967 x86: Optimize strcspn and strpbrk in strcspn-c.c
0a2da01110 x86: Optimize strspn in strspn-c.c
0dafa75e3c x86: Remove strcspn-sse2.S and use the generic implementation
3811544655 x86: Remove strpbrk-sse2.S and use the generic implementation
a4b1cae068 x86: Remove strspn-sse2.S and use the generic implementation
5997011826 x86: Optimize str{n}casecmp TOLOWER logic in strcmp.S
3605c74407 x86: Optimize str{n}casecmp TOLOWER logic in strcmp-sse42.S
3051cf3e74 x86: Add AVX2 optimized str{n}casecmp
b13a2e68eb x86: Add EVEX optimized str{n}casecmp
80883f4354 x86: Remove AVX str{n}casecmp
4ff6ae069b x86: Small improvements for wcslen
ffe75982cc x86: Remove memcmp-sse4.S
df5de87260 x86: Cleanup page cross code in memcmp-avx2-movbe.S
0a11305416 x86: Optimize {str|wcs}rchr-sse2
00f09a14d2 x86: Optimize {str|wcs}rchr-avx2
596c9a32cc x86: Optimize {str|wcs}rchr-evex
1f83d40dfa elf: Remove unused NEED_DL_BASE_ADDR and _dl_base_addr
b0bd6a1323 elf: Merge dl-sysdep.c into the Linux version
2139b1848e Linux: Remove HAVE_AUX_SECURE, HAVE_AUX_XID, HAVE_AUX_PAGESIZE
458733fffe Linux: Remove DL_FIND_ARG_COMPONENTS
08728256fa Linux: Assume that NEED_DL_SYSINFO_DSO is always defined
4b9cd5465d Linux: Consolidate auxiliary vector parsing
1cc4ddfeeb Revert "Linux: Consolidate auxiliary vector parsing"
28bdb03b1b Linux: Include <dl-auxv.h> in dl-sysdep.c only for SHARED
ff900fad89 Linux: Consolidate auxiliary vector parsing (redo)
be9240c84c elf: Remove __libc_init_secure
1e7b011f87 i386: Remove OPTIMIZE_FOR_GCC_5 from Linux libc-do-syscall.S
1a5b9d1a23 i386: Honor I386_USE_SYSENTER for 6-argument Linux system calls
b38c9cdb58 Linux: Define MMAP_CALL_INTERNAL
b2387bea84 ia64: Always define IA64_USE_NEW_STUB as a flag macro
e7ca2a475c Linux: Implement a useful version of _startup_fatal
43d77ef9b8 Linux: Introduce __brk_call for invoking the brk system call
ede8d94d15 csu: Implement and use _dl_early_allocate during static startup
89b638f48a S390: Enable static PIE
c73c79af7d rtld: Use generic argv adjustment in ld.so [BZ #23293]
b2585cae28 linux: Add a getauxval test [BZ #23293]
14770f3e04 string.h: fix __fortified_attr_access macro call [BZ #29162]
83ae8287c1 x86: Fallback {str|wcs}cmp RTM in the ncmp overflow case [BZ #29127]
ff450cdbde Fix deadlock when pthread_atfork handler calls pthread_atfork or dlclose
b349fe0722 misc: Use 64 bit stat for daemon (BZ# 29203)
aa8a87f51d misc: Use 64 bit stat for getusershell (BZ# 29204)
9db6a597ef posix: Use 64 bit stat for posix_fallocate fallback (BZ# 29207)
f9c3e57ac2 posix: Use 64 bit stat for fpathconf (_PC_ASYNC_IO) (BZ# 29208)
61fd3e0e74 socket: Use 64 bit stat for isfdtype (BZ# 29209)
34422108f4 inet: Use 64 bit stat for ruserpass (BZ# 29210)
52431199b5 catgets: Use 64 bit stat for __open_catalog (BZ# 29211)
b3f935940e iconv: Use 64 bit stat for gconv_parseconfdir (BZ# 29213)
9947f2df19 socket: Fix mistyped define statement in socket/sys/socket.h (BZ #29225)
4c92a10412 powerpc: Fix VSX register number on __strncpy_power9 [BZ #29197]
a7ec6363a3 nptl: Fix __libc_cleanup_pop_restore asynchronous restore (BZ#29214)
96944f0f81 hppa: Remove _dl_skip_args usage (BZ# 29165)
bb4148283f nios2: Remove _dl_skip_args usage (BZ# 29187)
368c5c3e00 nss: add assert to DB_LOOKUP_FCT (BZ #28752)
94ab2088c3 nss: handle stat failure in check_reload_and_get (BZ #28752)
4b246b2bbd linux: Fix mq_timereceive check for 32 bit fallback code (BZ 29304)
7789a84923 nptl: Fix ___pthread_unregister_cancel_restore asynchronous restore
8d324019e6 x86_64: Remove end of line trailing spaces
eb9aa96fac x86_64: Remove bzero optimization
8ab861d295 x86_64: Implement evex512 version of strlen, strnlen, wcslen and wcsnlen
f6bc52f080 x86-64: Ignore r_addend for R_X86_64_GLOB_DAT/R_X86_64_JUMP_SLOT
82a707aeb7 x86_64: Add strstr function with 512-bit EVEX
70be93d1c5 x86: Create header for VEC classes in x86 strings library
e805606193 x86: Add COND_VZEROUPPER that can replace vzeroupper if no `ret`
4901009dad x86: Optimize memrchr-sse2.S
83a986e9fb x86: Optimize memrchr-evex.S
b05bd59823 x86: Optimize memrchr-avx2.S
a910d7e164 x86: Shrink code size of memchr-avx2.S
3c87383a20 x86: Shrink code size of memchr-evex.S
820504e3ed x86: ZERO_UPPER_VEC_REGISTERS_RETURN_XTEST expect no transactions
fc54e1fae8 x86: Align varshift table to 32-bytes
6e008c884d x86: Fix misordered logic for setting `rep_movsb_stop_threshold`
9d50e162ee x86: Add sse42 implementation to strcmp's ifunc
94b0dc9419 x86: Add bounds `x86_non_temporal_threshold`
ba1c3f23d9 x86: Cleanup bounds checking in large memcpy case
c51d8d383c x86: Add BMI1/BMI2 checks for ISA_V3 check
d201c59177 x86: Align entry for memrchr to 64-bytes.
aadd0a1c7c x86: Put wcs{n}len-sse4.1 in the sse4.1 text section
f4598f0351 x86: Add definition for __wmemset_chk AVX2 RTM in ifunc impl list
7079931c51 x86: Move and slightly improve memset_erms
35f9c72c8b x86: Move mem{p}{mov|cpy}_{chk_}erms to its own file
ccc54bd61c x86: Add missing IS_IN (libc) check to strncmp-sse4_2.S
b991af5063 Update syscall-names.list for Linux 5.18
b2f32e7464 malloc: Simplify implementation of __malloc_assert
875b2414cd dlfcn: Pass caller pointer to static dlopen implementation (bug 29446)
4ab59ce4e5 Update syscall lists for Linux 5.19
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit c97f918d37)
python3.11 beta is out but fails to run the makefile currently
this supports python versions from 3.6 to 3.99 with the python3 binary
it also checks specifically for 3.11 as it is the latest version out
Signed-off-by: Oscar Molnar <oscar@tymscar.com>
(cherry picked from commit a9e8eec221)
Commit 21f460a5db ("ath25: fix duplicate LZMA compression") changed
the way kernel images are generated, affecting initramfs images instead.
Initramfs images were previously ELF images, and by mistake this change
caused the raw kernel image to be used as a source. This caused them to
be non-loadable by bootloaders.
Restore the previous KERNEL_INITRAMFS recipe and adjust
KERNEL_INITRAMFS_NAME to point at the correct source artifact.
While at that, adjust KERNEL_INITRAMFS_SUFFIX to -kernel.elf,
so it matches the suffix of non-initramfs kernel artifact.
Fixes: 21f460a5db ("ath25: fix duplicate LZMA compression")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 9f5cbb6e8b)
Commit 21f460a5db ("ath25: fix duplicate LZMA compression"), when
attempting to restore ELF artifact generation, copiedover the raw
kernel image twice. Because of that, the .elf artifact was actually a
duplicate of raw image.
Fix that by copying over .elf suffixed kernel image instead.
Fixes: 21f460a5db ("ath25: fix duplicate LZMA compression")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 611291383a)
This backports some patches from kernel 5.15 to fix issues with
flowtable offloading in kernel 5.10. OpenWrt backports most of the
patches related to flowtable offloading from kernel 5.15 already, but we
are missing some of the extra fixes.
This fixes some connection tracking problems when a flow gets removed
from the offload and added to the normal SW path again.
The patch 614-v5.18-netfilter-flowtable-fix-TCP-flow-teardown.patch was
extended manually with the nf_conntrack_tcp_established() function.
All changes are already included in kernel 5.15.
Fixes: #8776
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 96ef2dabce)
Before this commit, it was assumed that pkg-config.real is in the PATH. While
this was fine for the normal build workflow, this led to some issues if
make TOPDIR="$(pwd)" -C "$pkgdir" compile
was called manually. The command failed with
Makefile:15: *** No libnl-tiny development libraries found!. Stop.
make[1]: Leaving directory
since pkg-config of the host system was used.
After the commit, the package is built sucessfully.
Signed-off-by: Leonardo Mörlein <me@irrelefant.net>
(cherry picked from commit 37c0d15a8e)
This adds the SMSC PHY which is needed by the kmod-usb-net-smsc95xx
driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5b016a88f9)
This adds the AX88796B PHY which is needed by the kmod-usb-net-asix
driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 712ff388bc)
The ulog iptables target was removed with kernel 3.17, remove the kernel
and also the iptables package in OpenWrt too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 2a0284fb03)
The nft NAT packages for IPv4 and IPv6 were merged into the common
packages with kernel 5.1. The kmod-nft-nat6 package was empty in our
build, remove it.
Multiple kernel configuration options were also removed, remove them
from our generic kernel configuration too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b75425370d)
Add the ipset/ip_set_hash_ipmac.ko file. The CONFIG_IP_SET_HASH_IPMAC
KConfig option is already set by the package.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
(cherry picked from commit 6a2e9f3da6)
