Replace patches for MediaTek Ethernet driver SGMII/SerDes unit with
their corresponding upstream patches. Not all of the patches in our
tree went upstream as-is, some are slightly different implementations,
and they require the phylink_pcs helpers now made available.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It isn't feasible to literally backport all upstream phylink_pcs changes
down to Linux 5.15: It's just too many patches, and many downstream
drivers and hacks are likely to break. We are too close to branching off
to risk this, and it's also just too much work.
Instead just add helper functions used by modern PCS drivers while keeping
the original functions instact as well. While this may add a kilobyte or
two of extra kernel size, it has the advantage that we get the best of both
worlds: None of the existing codepaths are touched, but yet we have the
option to backport singular improvements to Ethernet drivers where needed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The current patches are old, update them from mainline.
Backports taken from https://github.com/yuzhaogoogle/linux/commits/mglru-5.15
Tested-by: Kazuki H <kazukih0205@gmail.com> #mt7622/Linksys E8450 UBI
Signed-off-by: Kazuki H <kazukih0205@gmail.com>
General specification:
SoC Type: MediaTek MT7620N (580MHz)
ROM: 8 MB SPI-NOR (W25Q64FV)
RAM: 64 MB DDR (EM6AB160TSD-5G)
Switch: MediaTek MT7530
Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
Wireless: 2.4 GHz (MediaTek RT5390): b/g/n
Buttons: 3 button (POWER, RESET, WPS)
Slide switch: 4 position (BASE, ADAPTER, BOOSTER, ACCESS POINT)
Bootloader: U-Boot 1.1.3
Power: 9 VDC, 0.6 A
MAC in stock:
|- + |
| LAN | RF-EEPROM + 0x04 |
| WLAN | RF-EEPROM + 0x04 |
| WAN | RF-EEPROM + 0x28 |
OEM easy installation
1. Use a PC to browse to http://my.keenetic.net.
2. Go to the System section and open the Files tab.
3. Under the Files tab, there will be a list of system
files. Click on the Firmware file.
4. When a modal window appears, click on the Choose File
button and upload the firmware image.
5. Wait for the router to flash and reboot.
OEM installation using the TFTP method
1. Download the latest firmware image and rename it to
klite3_recovery.bin.
2. Set up a Tftp server on a PC (e.g. Tftpd32) and place the
firmware image to the root directory of the server.
3. Power off the router and use a twisted pair cable to connect
the PC to any of the router's LAN ports.
4. Configure the network adapter of the PC to use IP address
192.168.1.2 and subnet mask 255.255.255.0.
5. Power up the router while holding the reset button pressed.
6. Wait approximately for 5 seconds and then release the
reset button.
7. The router should download the firmware via TFTP and
complete flashing in a few minutes.
After flashing is complete, use the PC to browse to
http://192.168.1.1 or ssh to proceed with the configuration.
Signed-off-by: Alexey Bartenev <41exey@proton.me>
The generic subtarget supports only a few devices. None of
these devices are equipped with a ADM6996 switch. On the
mips74k subtarget, the driver for the adm6996 switch is
disabled. So it seems that the ADM6996 driver should
be enabled only on the legacy subtarget.
Support for ADM6996 switches was enabled in commit 68081fc1c8.
At the time when this driver was enabled the bcm47xx
target had only one subtarget.
Switches used by individual devices suported by the generic
subtarget are listed below.
Device Switch
Edimax PS-1208MFG int. SoC
Linksys WRT300N v1.1 Broadcom BCM5325
Linksys WRT310N v1 Broadcom BCM5397
Linksys WRT350N v1 Broadcom BCM5397
Linksys WRT610N v1 Broadcom BCM53115
Linksys WRT610N v2 Broadcom BCM53115
Linksys E3000 v1 Broadcom BCM53115
Reduce uncompressed kernel size by 8320 Bytes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
The AVM FRITZ!Box 7330 shares hardware with the AVM Fritzbox 7320
except for the second ethernet port, which only supports 100M.
Hardware:
- SoC: Lantiq ARX 188
- CPU: 2x MIPS 34Kc 393 MHz
- RAM: 64 MiB 196 MHz
- Flash: 16 MiB NAND
- Ethernet: Built-in Gigabit Ethernet switch, 1x 1GbE, 1x 100M
- Wifi: Atheros AR9227-BC2A b/g/n with 2 pcb/internal antennas
- USB: 2x USB 2.0
- DSL: Built-in ADSL2+ modem
- DECT: Dialog SC14441
- LEDs: 1 two-color, 4 one-color
- Buttons: 1x DECT, 1x WIFI
- Telephone connectors: 1 FXS port via TAE or RJ11 connector
Installation:
The installation process is described on the wiki.
Unsupported (same as AVM 7320):
- VoIP (DECT and FXS),
- Second Ethernet port.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This board is very similar to the Aruba AP-105, but is
outdoor-first. It is very similar to the MSR2000 (though certain
MSR2000 models have a different PHY[^1]).
A U-Boot replacement is required to install OpenWrt on these
devices[^2].
Specifications
--------------
* Device: Aruba AP-175
* SoC: Atheros AR7161 680 MHz MIPS
* RAM: 128MB - 2x Mira P3S12D40ETP
* Flash: 16MB MXIC MX25L12845EMI-10G (SPI-NOR)
* WiFi: 2 x DNMA-H92 Atheros AR9220-AC1A 802.11abgn
* ETH: IC+ IP1001 Gigabit + PoE PHY
* LED: 2x int., plus 12 ext. on TCA6416 GPIO expander
* Console: CP210X linking USB-A Port to CPU console @ 115200
* RTC: DS1374C, with internal battery
* Temp: LM75 temperature sensor
Factory installation:
- Needs a u-boot replacement. The process is almost identical to that
of the AP105, except that the case is easier to open, and that you
need to compile u-boot from a slightly different branch:
https://github.com/Hurricos/u-boot-ap105/tree/ap175
The instructions for performing an in-circuit reflash with an
SPI-Flasher like a CH314A can be found on the OpenWrt Wiki
(https://openwrt.org/toh/aruba/ap-105); in addition a detailed guide
may be found on YouTube[^3].
- Once u-boot has been replaced, a USB-A-to-A cable may be used to
connect your PC to the CP210X inside the AP at 115200 baud; at this
point, the normal u-boot serial flashing procedure will work (set up
networking; tftpboot and boot an OpenWrt initramfs; sysupgrade to
OpenWrt proper.)
- There is no built-in functionality to revert back to stock firmware,
because the AP-175 has been declared by the vendor[^4] end-of-life
as of 31 Jul 2020. If for some reason you wish to return to stock
firmware, take a backup of the 16MiB flash before flashing u-boot.
[^1]: https://github.com/shalzz/aruba-ap-310/blob/master/platform/bootloader/apboot-11n/include/configs/msr2k.h#L186
[^2]: https://github.com/Hurricos/u-boot-ap105/tree/ap175
[^3]: https://www.youtube.com/watch?v=Vof__dPiprs
[^4]: https://www.arubanetworks.com/support-services/end-of-life/#product=access-points&version=0
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
One user reported that his SIMAX1800T couldn't boot like the others. After
debugging, I found that this was caused by the disabled PCIe port. I cannot
reproduce this issue on my SIMAX1800T. But when I disabled pcie2 on the
ASUS RT-AC57U, I got the same result.
It seems that disabling these unused PCIe ports on some mt7621 revisions
will cause PCIe to fail to initialize. So we'd better to re-enable them on
all related mt7621 devices.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
There's no valid mac address for the second band in the eeprom.
The vendor fw uses 2.4G mac + 4 as the mac for 5G radio.
Do the same in our firmware.
Fixes: 23be410b3d ("ramips: add support for TOTOLINK X5000R")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration
data from the nvmem subsystem.
This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.
Currently, only ethernet devices uses the mac address of
"mac-address-ascii" cells, while PCI ath9k devices uses the mac address
within calibration data.
Signed-off-by: Edward Chow <equu@openmail.cc>
(restored switch configuration in 02_network, integrated caldata into
partition)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
this was thoroughly tested (warm and cold boots). on a
real 7360v2. This is because there have been documented
hick-ups with other lantiq devices that need the
owl-loader too.
It's likely that the 7360(sl) could be converted in the
same way as well. However the 7362sl uses a reversed
caldata format, so the "qca,no-eeprom" stays in place.
The patch also moves the urloader nvmem partition
definition into the partition section.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
libdeflate's gzip compressor provides a better
compression ratio and uboot's decompressor has
no problem with the data streams.
Tested on MX60, WNDR4700, WNDAP660
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
It appears that the refactor of the upgrade process for NAND devices
resulted in the nand_do_upgrade_success step not being called for
devices using the linksys.sh script. As a result, configuration
was not preserved over sysupgrade steps.
This was restored for some devices in
commit 84ff6c90dd ("base-files: bring back nand_do_upgrade_success").
This restored preservation of config for ipq40xx devices using the
linksys.sh script. Other devices and targets have not been examined.
Closes: #11677
Fixes: e25e6d8e54 ("base-files: fix and clean up nand sysupgrade code")
Tested-on: EA8300
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
(checkpatch nitpick)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Sercomm H500-s devices don't need the JFFS2 cleanmarkers as opposed to the
other bmips NAND devices.
Fixes: 6df12200d9 ("bmips: add support for Sercomm H-500s")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Hardware
--------
SOC: MediaTek MT7986
RAM: 512MB DDR3
FLASH: 256MB SPI-NAND (Winbond W25N02KV)
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
MaxLinear GPY211C 2.5 N-Base-T PHY
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not ocnnect VCC)
Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.66/24. Rename the image to tufax4200.bin.
2. Connect the TFTP server to the AX4200. Conect to the serial console,
interrupt the autoboot process by pressing '4' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.66
$ tftpboot 0x46000000 tufax4200.bin
$ bootm 0x46000000
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Missing features
----------------
- The LAN port LEDs are driven by the switch but OpenWrt does not
correctly configure the output.
Signed-off-by: David Bauer <mail@david-bauer.net>
The ASUS TUF-AX4200 bootloader adds invalid parameters for the rootfs.
Without overwriting the cmdline, the kernel crashes when trying to
attach the rootfs, as OpenWrt uses a different partition than the vendor
OS.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add a patch to allow modification of the PHY LED configuration. This is
required for boards, where the reset configuration of LED functions is
incompatibe with the usage of the device LEDs.
This is the case for the ASUS TUF-AX4200 Wireless router. It requires
modification of the LED configuration because as the WAN LED on the
front of the device is driven by the PHY. Without patching, it would
only illuminate in case the Link speed is 100 Mbit/s.
Signed-off-by: David Bauer <mail@david-bauer.net>
This flash-chip is used on the Asus TUF-AX4200 and TUF-AX6000 routers.
As the filogic target only uses kernel 5.15, skip the 5.10 backport.
Signed-off-by: David Bauer <mail@david-bauer.net>
This can improve load balancing by pushing backlog (and RPS) processing
to separate threads, allowing the scheduler to distribute the load.
It can be enabled with: echo 1 > /proc/sys/net/core/backlog_threaded
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Hardware
========
- SoC: MediaTek MT7621AT (880MHz, Duel-Core)
- RAM: DDR3 128MB
- Flash: Winbond W25Q128JV (SPI-NOR 16MB)
- WiFi: MediaTek MT7915D (2.4GHz, 5GHz, DBDC)
- Ethernet: MediaTek MT7530 (WAN x1, LAN x3, SoC)
- UART: >TX RX GND 3v3 (115200 8N1, J1)
Do not connect 3v3. TX is marked with an arrow.
Installation
============
Flash factory image. This can be done using stock web ui.
Revert to stock firmware
========================
Flash stock firmware via OEM Web UI Recovery mode.
Web UI Recovery method
======================
1. Unplug the router
2. Plug in and hold reset button 5~10 secs
3. Set your computer IP address manually to 192.168.1.x / 255.255.255.0
4. Flash image with web browser to 192.168.1.1
Co-authored-by: Robert Senderek <robert.senderek@10g.pl>
Co-authored-by: Yoonji Park <koreapyj@dcmys.kr>
Signed-off-by: David Bauer <mail@david-bauer.net>
These patches have now received a positive review upstream, so let's add them
to pending patches.
776-net-dsa-b53-mmap-add-phy-ops.patch:
This is mostly bmips/bcm63xx-specific to get external switches working
without hanging the device when accessing certain registers.
777-net-dsa-b53-mdio-add-support-for-BCM53134:
This adds support for BCM53134 switch on DSA B53, so any target using DSA B53
can benefit from it.
Also fix sercomm-h500-s external switch IMP port phy-mode.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Refreshing the patches for fff07085fb moved the b53_adjust_63xx_rgmii() call
from b53_phylink_mac_link_up() to b53_phylink_mac_link_down().
In order to properly configure the RGMII ports we need to restore it to its
correct place.
Fixes: fff07085fb ("kernel: add pending bmips patches")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Ruckus ZoneFlex 7363 is a dual-band, dual-radio 802.11n 2x2 MIMO enterprise
access point. ZoneFlex 7343 is the single band variant of 7363
restricted to 2.4GHz, and ZoneFlex 7341 is 7343 minus two Fast Ethernet
ports.
Hardware highligts:
- CPU: Atheros AR7161 SoC at 680 MHz
- RAM: 64MB DDR
- Flash: 16MB SPI-NOR
- Wi-Fi 2.4GHz: AR9280 PCI 2x2 MIMO radio with external beamforming
- Wi-Fi 5GHz: AR9280 PCI 2x2 MIMO radio with external beamforming
- Ethernet 1: single Gigabit Ethernet port through Marvell 88E1116R gigabit PHY
- Ethernet 2: two Fast Ethernet ports through Realtek RTL8363S switch,
connected with Fast Ethernet link to CPU.
- PoE: input through Gigabit port
- Standalone 12V/1A power input
- USB: optional single USB 2.0 host port on the -U variants.
Serial console: 115200-8-N-1 on internal H1 header.
Pinout:
H1 ----------
|1|x3|4|5|
----------
Pin 1 is near the "H1" marking.
1 - RX
x - no pin
3 - VCC (3.3V)
4 - GND
5 - TX
Installation:
- Using serial console - requires some disassembly, 3.3V USB-Serial
adapter, TFTP server, and removing a single PH1 screw.
0. Connect serial console to H1 header. Ensure the serial converter
does not back-power the board, otherwise it will fail to boot.
1. Power-on the board. Then quickly connect serial converter to PC and
hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
you'll enter U-boot shell. Then skip to point 3.
Connection parameters are 115200-8-N-1.
2. Allow the board to boot. Press the reset button, so the board
reboots into U-boot again and go back to point 1.
3. Set the "bootcmd" variable to disable the dual-boot feature of the
system and ensure that uImage is loaded. This is critical step, and
needs to be done only on initial installation.
> setenv bootcmd "bootm 0xbf040000"
> saveenv
4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed.
Use the Gigabit interface, Fast Ethernet ports are not supported
under U-boot:
> setenv serverip 192.168.1.2
> setenv ipaddr 192.168.1.1
> tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7363-initramfs-kernel.bin
> bootm 0x81000000
5. Optional, but highly recommended: back up contents of "firmware" partition:
$ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7363_fw_backup.bin
6. Copy over sysupgrade image, and perform actual installation. OpenWrt
shall boot from flash afterwards:
$ ssh root@192.168.1.1
# sysupgrade -n openwrt-ath79-generic-ruckus_zf7363-squashfs-sysupgrade.bin
After unit boots, it should be available at the usual 192.168.1.1/24.
Return to factory firmware:
1. Copy over the backup to /tmp, for example using scp
2. Unset the "bootcmd" variable:
fw_setenv bootcmd ""
3. Use sysupgrade with force to restore the backup:
sysupgrade -F ruckus_zf7363_backup.bin
4. System will reboot.
Quirks and known issues:
- Fast Ethernet ports on ZF7363 and ZF7343 are supported, but management
features of the RTL8363S switch aren't implemented yet, though the
switch is visible over MDIO0 bus. This is a gigabit-capable switch, so
link establishment with a gigabit link partner may take a longer time
because RTL8363S advertises gigabit, and the port magnetics don't
support it, so a downshift needs to occur. Both ports are accessible
at eth1 interface, which - strangely - runs only at 100Mbps itself.
- Flash layout is changed from the factory, to use both firmware image
partitions for storage using mtd-concat, and uImage format is used to
actually boot the system, which rules out the dual-boot capability.
- Both radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
OpenWrt by choice.
It is controlled by data in the top 64kB of RAM which is unmapped,
to avoid the interference in the boot process and accidental
switch to the inactive image, although boot script presence in
form of "bootcmd" variable should prevent this entirely.
- On some versions of stock firmware, it is possible to obtain root shell,
however not much is available in terms of debugging facitilies.
1. Login to the rkscli
2. Execute hidden command "Ruckus"
3. Copy and paste ";/bin/sh;" including quotes. This is required only
once, the payload will be stored in writable filesystem.
4. Execute hidden command "!v54!". Press Enter leaving empty reply for
"What's your chow?" prompt.
5. Busybox shell shall open.
Source: https://alephsecurity.com/vulns/aleph-2019014
- There is second method to achieve root shell, using command injection
in the web interface:
1. Login to web administration interface
2. Go to Administration > Diagnostics
3. Enter |telnetd${IFS}-p${IFS}204${IFS}-l${IFS}/bin/sh into "ping"
field
4. Press "Run test"
5. Telnet to the device IP at port 204
6. Busybox shell shall open.
Source: https://github.com/chk-jxcn/ruckusremoteshell
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Ruckus ZoneFlex 7351 is a dual-band, dual-radio 802.11n 2x2 MIMO enterprise
access point.
Hardware highligts:
- CPU: Atheros AR7161 SoC at 680 MHz
- RAM: 64MB DDR
- Flash: 16MB SPI-NOR
- Wi-Fi 2.4GHz: AR9280 PCI 2x2 MIMO radio with external beamforming
- Wi-Fi 5GHz: AR9280 PCI 2x2 MIMO radio with external beamforming
- Ethernet: single Gigabit Ethernet port through Marvell 88E1116R gigabit PHY
- Standalone 12V/1A power input
- USB: optional single USB 2.0 host port on the 7351-U variant.
Serial console: 115200-8-N-1 on internal H1 header.
Pinout:
H1 ----------
|1|x3|4|5|
----------
Pin 1 is near the "H1" marking.
1 - RX
x - no pin
3 - VCC (3.3V)
4 - GND
5 - TX
Installation:
- Using serial console - requires some disassembly, 3.3V USB-Serial
adapter, TFTP server, and removing a single T10 screw.
0. Connect serial console to H1 header. Ensure the serial converter
does not back-power the board, otherwise it will fail to boot.
1. Power-on the board. Then quickly connect serial converter to PC and
hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
you'll enter U-boot shell. Then skip to point 3.
Connection parameters are 115200-8-N-1.
2. Allow the board to boot. Press the reset button, so the board
reboots into U-boot again and go back to point 1.
3. Set the "bootcmd" variable to disable the dual-boot feature of the
system and ensure that uImage is loaded. This is critical step, and
needs to be done only on initial installation.
> setenv bootcmd "bootm 0xbf040000"
> saveenv
4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed:
> setenv serverip 192.168.1.2
> setenv ipaddr 192.168.1.1
> tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7351-initramfs-kernel.bin
> bootm 0x81000000
5. Optional, but highly recommended: back up contents of "firmware" partition:
$ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7351_fw_backup.bin
6. Copy over sysupgrade image, and perform actual installation. OpenWrt
shall boot from flash afterwards:
$ ssh root@192.168.1.1
# sysupgrade -n openwrt-ath79-generic-ruckus_zf7351-squashfs-sysupgrade.bin
After unit boots, it should be available at the usual 192.168.1.1/24.
Return to factory firmware:
1. Copy over the backup to /tmp, for example using scp
2. Unset the "bootcmd" variable:
fw_setenv bootcmd ""
3. Use sysupgrade with force to restore the backup:
sysupgrade -F ruckus_zf7351_backup.bin
4. System will reboot.
Quirks and known issues:
- Flash layout is changed from the factory, to use both firmware image
partitions for storage using mtd-concat, and uImage format is used to
actually boot the system, which rules out the dual-boot capability.
- Both radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
OpenWrt by choice.
It is controlled by data in the top 64kB of RAM which is unmapped,
to avoid the interference in the boot process and accidental
switch to the inactive image, although boot script presence in
form of "bootcmd" variable should prevent this entirely.
- On some versions of stock firmware, it is possible to obtain root shell,
however not much is available in terms of debugging facitilies.
1. Login to the rkscli
2. Execute hidden command "Ruckus"
3. Copy and paste ";/bin/sh;" including quotes. This is required only
once, the payload will be stored in writable filesystem.
4. Execute hidden command "!v54!". Press Enter leaving empty reply for
"What's your chow?" prompt.
5. Busybox shell shall open.
Source: https://alephsecurity.com/vulns/aleph-2019014
- There is second method to achieve root shell, using command injection
in the web interface:
1. Login to web administration interface
2. Go to Administration > Diagnostics
3. Enter |telnetd${IFS}-p${IFS}204${IFS}-l${IFS}/bin/sh into "ping"
field
4. Press "Run test"
5. Telnet to the device IP at port 204
6. Busybox shell shall open.
Source: https://github.com/chk-jxcn/ruckusremoteshell
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Sercomm H-500s is a BCM63268 with 128M, internal and external (Quantenna) wifi
and external BCM53134S switch.
This device is already supported in bcm63xx target, so more information can be
found in https://openwrt.org/toh/sercomm/h500-s.
It's a perfect example of a device with internal and external switch
coexistance since most devices only have ports on one of the switches but not
both of them.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
bcm63268-timer-clocks have been sent upstream with a positive review, so let's
add them to pending v5.15.
Also add devm_clk_hw_register_gate() patch from v5.17 to backports since it's
needed for upstream bcm63268-timer-clocks patches.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Fixes the following warnings for Netgear DGND3700v2 and Comtrend VR-3032u:
[ 1.059540] 7 fixed-partitions partitions found on MTD device brcmnand.0
[ 1.066570] OF: Bad cell count for /ubus/nand@10000200/nandcs@0/partitions
[ 1.073766] OF: Bad cell count for /ubus/nand@10000200/nandcs@0/partitions
[ 1.081927] OF: Bad cell count for /ubus/nand@10000200/nandcs@0/partitions
[ 1.089128] OF: Bad cell count for /ubus/nand@10000200/nandcs@0/partitions
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Huawei HG253s v2 is a BCM6362 with 128M RAM, internal wifi and external
BCM53124S switch.
This device is already supported in bcm63xx target, so more information can be
found in https://openwrt.org/toh/huawei/hg253s_v2.
It's a perfect example of a device with internal and external switch
coexistance since most devices only have ports on one of the switches but not
both of them.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The Netgear DGND3700v2 has an external BCM53125 switch which can now be enabled
as a DSA disjoint switch tree setup.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Without this change, internal and external B53 switches couldn't coexist as
reported in https://github.com/openwrt/openwrt/issues/10313.
In order to fix this we need to force the B53 MMAP DSA switch driver to use
bcm6368-mdio-mux for accessing the PHY registers instead of its own phy_read()
and phy_write() functions.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Adds support for the Wallys DR40x9 series boards.
They come in IPQ4019 and IPQ4029 versions.
IPQ4019/4029 only differ in that that IPQ4029 is the industrial version that is rated to higher temperatures.
Specifications are:
* CPU: Qualcomm IPQ40x9 (4x ARMv7A Cortex A7) at 716 MHz
* RAM: 512 MB
* Storage: 2MB of SPI-NOR, 128 MB of parallel NAND
* USB 3.0 TypeA port for users
* MiniPCI-E with PCI-E 2.0 link
* MiniPCI-E for LTE modems with only USB2.0 link
* 2 SIM card slots that are selected via GPIO11
* MicroSD card slot
* Ethernet: 2x GBe with 24~48V passive POE
* SFP port (Does not work, I2C and GPIO's not connected on hardware)
* DC Jack
* UART header
* WLAN: In-SoC 2x2 802.11b/g/n and 2x2 802.11a/n/ac
* 4x MMCX connectors for WLAN
* Reset button
* 8x LED-s
Installation instructions:
Connect to UART, pins are like this:
-> 3.3V | TX | RX | GND
Settings are 115200 8n1
Boot initramfs from TFTP:
tftpboot 0x84000000 openwrt-ipq40xx-generic-wallys_dr40x9-initramfs-fit-uImage.itb
bootm
Then copy the sysupgrade image to the /tmp folder and execute sysupgrade -n <image_name>
The board file binary was provided from Wallystech on March 14th 2023
including full permission to use and distribute.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
The original claim about conflicting MAC addresses is wrong. mac80211
does increment the first octet and sets the LA bit.
This means our "workaround" actually leads to the issue while
incrementing the last octet is safe.
Signed-off-by: David Bauer <mail@david-bauer.net>
Cases have been reported in which certain devices do not boot correctly
or have errors. After various tests by users who have such errors it has
been concluded that the SPI frequency should be reduced to 40Mhz, at
this speed it appears that all devices work correctly.
Signed-off-by: Óscar García Amor <ogarcia@connectical.com>
Manually rebased:
ramips/patches-5.10/810-uvc-add-iPassion-iP2970-support.patch
All other patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
Disable interrupts for the eth-PHYs, as the interrupts are either not
firing or lost within the stack. Switch to polling the PHY status in the
meantime until a proper fix is implemented.
Ref: https://github.com/openwrt/openwrt/issues/12192
Signed-off-by: David Bauer <mail@david-bauer.net>
The boot-procedure for the Extreme WS-AP3825I is vfragile to put it
mildly. It does not relocate the FDT properly. It currently exercises
every step manually as well as coming with a pre-padded dtb.
Use the PowerPC bootwrapper code for legacy platforms with a pre-filles
DTS instead. We still need to ship a fit image to not break the fdt
resize / relocate instructions on existing boards. This does not require
adapting the U-Boot bootcommand.
Ref: https://github.com/openwrt/openwrt/issues/12223
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes issues with legacy boot loaders that don't process reserved memory
regions outside of system RAM
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move it to pending, since it wasn't actually accepted upstream yet.
Fixes potential issues when doing offload between multiple MACs.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Netgear WAX218 is a 802.11ax AP claiming AX3600 support. It is wall
or ceiling mountable. It can be powered via PoE, or a 12 V adapter.
The board has footprints for 2.54mm UART headers. They're difficult to
solder because the GND is connected to a large copper plane. Only try
soldering if you are very skilled. Otherwise, use pogo pins.
Specifications:
---------------
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 366 MB of RAM available to OS, not sure of total amount
* Storage: Macronix MX30UF2G18AC 256MB NAND
* Ethernet:
* 2.5G RJ45 port (QCA8081) with PoE input
* WLAN:
* 2.4GHz/5GHz with 8 antennas
* LEDs:
* Power (Amber)
* LAN (Blue)
* 2G WLAN (Blue)
* 5G WLAN (Blue)
* Buttons:
* 1x Factory reset
* Power: 12V DC Jack
* UART: Two 4-pin unpopulated headers near the LEDs
* "J2 UART" is the CPU UART, 3.3 V level
Installation:
=============
Web UI method
-------------
Flashing OpenWRT using the vendor's Web UI is problematic on this
device. The u-boot mechanism for communicating the active rootfs is
antiquated and unreliable. Instead of setting the kernel commandline,
it relies on patching the DTS partitions of the nand node. The way
partitions are patched is incompatible with newer kernels.
Newer kernels use the SMEM partition table, which puts "rootfs" on
mtd12. The vendor's Web UI will flash to either mtd12 or mtd14. One
reliable way to boot from mtd14 and avoid boot loops is to use an
initramfs image.
1. In the factory web UI, navigate to System Manager -> Firmware.
2. In the "Local Firmware Upgrade" section, click Browse
3. Navigate and select the 'web-ui-factory.fit' image
4. Click "Upload"
5. On the following page, click on "Proceed"
The flash proceeds at this point and the system will reboot
automatically to OpenWRT.
6. Flash the 'nand-sysupgrade.bin' using Luci or the commandline
SSH method
----------
Enable SSH using the CLI or Web UI. The root account is locked out to
ssh, and the admin account defaults to Netgear's CLI application.
So we need to get creative:
First, make sure the device boots from the second firmware partition:
ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \
/usr/sbin/fw_setenv active_fw 1
Then reboot the device, and run the update:
scp -O -o kexalgorithms=diffie-hellman-group14-sha1 \
-o hostkeyalgorithms=ssh-rsa \
netgear_wax218-squashfs-nand-factory.ubi \
admin@<ipaddr>:/tmp/openwrt.ubi
ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \
/usr/sbin/ubiformat /dev/mtd12 -f /tmp/openwrt.ubi
ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \
/usr/sbin/fw_setenv active_fw 0
Now reboot the device, and it should boot into a ready-to-use OpenWRT.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Francisco G Luna <frangonlun@gmail.com>
The wrapper-image for the WL-WDR4900 was used as a build-target for the
kernel. This workd fine as long as only a single wrapper is used with
the OpenWrt build-system.
If additional wrappers are used, the build becomes racy in the
wrapper-stage.
The wrapper images actually do not represent a target. They are built
based on the kernel configuration. Only copy the resulting images to
avoid race-conditions as explained.
Signed-off-by: David Bauer <mail@david-bauer.net>
As the mac-address readout never worked, the mac-address fillout by the
bootloader is sufficient. Remove the readout for the Watchguard T10
then.
Signed-off-by: David Bauer <mail@david-bauer.net>
The mac-address accessor functions were not included in the sourced
script. Fix this by importing the correct script path.
Signed-off-by: David Bauer <mail@david-bauer.net>
Make it possible to change the kernel configuration option
CONFIG_HARDLOCKUP_DETECTOR from OpenWrt.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
This sets the CONFIG_KCOV_IRQ_AREA_SIZE kernel configuration option to its default value.
This is shown when I set CONFIG_KERNEL_KCOV=y in the OpenWrt configuration on x86/64.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
This deactivates some kernel configuration options I see when
CONFIG_KERNEL_KASAN=y is set in the OpenWrt configuration on x86/64.
Set CONFIG_STACK_HASH_ORDER to its default value.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
This sets some kernel configuration options to their default values. I saw
these as warnings when I set CONFIG_KERNEL_UBSAN=y is set in the OpenWrt
configuration on x86/64.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
This deactivates some kernel configuration options I see when
CONFIG_KERNEL_DYNAMIC_FTRACE=y is set in the OpenWrt configuration on x86/64.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
This deactivates some kernel configuration options I see when
CONFIG_KERNEL_HIST_TRIGGERS=y is set in the OpenWrt configuration on x86/64.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
This deactivates some kernel configuration options I see when
CONFIG_KERNEL_DEBUG_VIRTUAL=y is set in the OpenWrt configuration on x86/64.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
This deactivates some kernel configuratoion options I see when
CONFIG_KERNEL_DEBUG_VM=y is set in the OpenWrt configuration on x86/64.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
Hardware
--------
SoC: Qualcomm IPQ8065
RAM: 512 MB DDR3
Flash: 256 MB NAND (Macronix MX30UF2G18AC) (split into 2x128MB)
4 MB SPI-NOR (Macronix MX25U3235F)
WLAN: Qualcomm Atheros QCA9984 - 2.4Ghz
Qualcomm Atheros QCA9984 - 5Ghz
ETH: eth0 - POE (100Mbps in U-Boot, 1000Mbps in OpenWrt)
eth1 - (1000Mbps in both)
Auto-negotiation broken on both.
USB: USB 2.0
LED: 5G, 2.4G, ETH1, ETH2, CTRL, PWR (All support green and red)
BTN: Reset
Other: SD card slot (non-functional)
Serial: 115200bps, near the Ethernet transformers, labeled 9X.
Connections from the arrow to the 9X text:
[NC] - [TXD] - [GND] - [RXD] - [NC]
Installation
------------
0. Connect to the device
Plug your computer into LAN2 (1000Mbps connection required).
If you use the LAN1/POE port, set your computer to force a 100Mbps link.
Connect to the device via TTL (Serial) 115200n8.
Locate the header (or solder pads) labeled 9X,
near the Ethernet jacks/transformers.
There should be an arrow on the other side of the header marking.
The connections should go like this:
(from the arrow to the 9X text): NC - TXD - GND - RXD - NC
1. Prepare for installation
While the AP is powering up, interrupt the startup process.
MAKE SURE TO CHECK YOUR CURRENT PARTITION!
If you see: "Current Partition is : partB" or
"Need to switch partition from partA to partB",
you have to force the device into partA mode, before continuing.
This can be done by changing the PKRstCnt to 5 and resetting the device.
setenv PKRstCnt 5
saveenv
reset
After you interrupt the startup process again,
you should see: Need to switch partition from partB to partA
You can now continue to the next step.
If you see: "Current Partition is : partA",
you can continue to the next step.
2. Prevent partition switching.
To prevent the device from switching partitions,
we are going to modify the startup command.
set bootcmd "setenv PKRstCnt 0; saveenv; bootipq"
setenv
3. First boot
Now, we have to boot the OpenWrt intifs.
The easiest way to do this is by using Tiny PXE.
You can also use the normal U-Boot tftp method.
Run "bootp" this will get an IP from the DHCP server
and possibly the firmware image.
If it doesn't download the firmware image, run "tftpboot".
Now run "bootm" to run the image.
You might see:
"ERROR: new format image overwritten - must RESET the board to recover"
this means that the image you are trying to load is too big.
Use a smaller image for the initial boot.
4. Install OpenWrt from initfs
Once you are booted into OpenWrt,
transfer the OpenWrt upgrade image and
use sysupgrade to install OpenWrt to the device.
Signed-off-by: Kristjan Krušič <kristjan.krusic@krusic22.com>
This commit adds the PHY reset gpio for the LAN1 port to the dts.
According to the GPL sources, gpios 34 and 36 are used on the AVM
FritzBox 7320 and 7330. The second port is unsupported.
The gpio assignment has been verified on the FritzBox 7330.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit includes some additional changes:
- better handling of iv and keys in openssl/wolfssl variants
- fix compiler warnings and whitespace
- build all 3 variants as separate packages
- adjust the new package name in targets' DEVICE_PACKAGES
- remove PKG_FLAGS:=nonshared
[Beeline SmartBox Flash - OK]
Tested-by: Mikhail Zhilkin <csharper2005@gmail.com>
[after test: replaced a hardcoded IV size of 16 by cipher_info->iv_size]
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Make sure it uses updated Jalapeno BDF inherited from
Device/8dev_jalapeno-common
Fixes: 146eb4925c ("ipq40xx: add support for Crisis Innovation Lab MeshPoint.One")
Signed-off-by: Mantas Pucka <mantas@8devices.com>
[ fix Fixes tag to correct format and fix commit title ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Set specific BDF file for 8devices Habanero/Jalapeno in ipq40xx
generic.mk
Signed-off-by: Mantas Pucka <mantas@8devices.com>
[ split ipq40xx changes in separate commit ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add new patch sent upstream for requesting the memory region in the bcm6345-l1
interrupt controller.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Hardware
--------
CPU: MediaTek MT7621 DAT
RAM: 128MB DDR3 (integrated)
FLASH: 16MB SPI-NOR ()
WiFi: MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax
SERIAL: 115200 8N1
LEDs - (3V3 - GND - RX - TX) - ETH ports
Installation
------------
Upload the factory image using the Web-UI.
Web-Recovery
------------
The router supports a HTTP recovery mode by holding the reset-button
when powering on. The interface is reachable at 192.168.0.1 and supports
installation using the factory image.
Signed-off-by: David Bauer <mail@david-bauer.net>
Setting this options modifies the rootfs size of created images. When
installing a large number of packages it may become necessary to
increase the size to have enough storage.
This option is only useful for supported devices, i.e. with an attached
SD Card or installed on a hard drive.
Signed-off-by: Paul Spooren <mail@aparcar.org>
